Open Access. Powered by Scholars. Published by Universities.®

Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Discipline
Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 189451 - 189480 of 196559

Full-Text Articles in Engineering

A Stable Explicit Method For Simultaneous Quasi‐Linear Differential Equations, Roy J. Brunson, Robert M. Wellek Jan 1971

A Stable Explicit Method For Simultaneous Quasi‐Linear Differential Equations, Roy J. Brunson, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.


Effects Of Molecular Characteristics Of Polymers On Drag Reduction, Gin‐Chain ‐C Liaw, Jacques L. Zakin, Gary Kent Patterson Jan 1971

Effects Of Molecular Characteristics Of Polymers On Drag Reduction, Gin‐Chain ‐C Liaw, Jacques L. Zakin, Gary Kent Patterson

Chemical and Biochemical Engineering Faculty Research & Creative Works

Turbulent measurements in capillary tubes and in pipes were made on nonpolar solutions of seven polymer species, three at more than one molecular weight, over wide concentration ranges. A critical concentration, Cc, was taken as the minimum concentration for disappearance of the turbulence transition region. Above this concentration, friction factor‐generalized Reynolds number data show only a gradual deviation from extension of the laminar line. Cc increases with tube diameter and decreases with molecular weight. The critical dimensionless volume friction Cc [η] is less dependent on molecular weight. The levels of Cc [η] for different polymer species in a given tube …


The Anodic Dissolution Of Tungsten, James W. Johnson, Cheng-Hsiao Wu Jan 1971

The Anodic Dissolution Of Tungsten, James W. Johnson, Cheng-Hsiao Wu

Chemical and Biochemical Engineering Faculty Research & Creative Works

The anodic dissolution of tungsten was studied in H2SO4-K2SO4 solutions (pH = -2 to 2.5) and K2SO4-K2CO3-KOH solutions (pH = 11.5 to 14.5) at 25 C. Faradaic efficiency studies in basic solutions showed the metal to be oxidized to the +6 state. In acid solutions, a thick protective film of yellow WO3 was formed. Polarization curves possessed linear Tafel regions (slope ~ 2.3 RT/F) at potentials slightly more positive than the rest potentials. An anodic dissolution mechanism is proposed which involves a surface film …


Mass Transfer Inside Liquid Droplets And Gas Bubbles Accompanied By A Second‐Order Chemical Reaction, R. J. Brunson, Robert M. Wellek Jan 1971

Mass Transfer Inside Liquid Droplets And Gas Bubbles Accompanied By A Second‐Order Chemical Reaction, R. J. Brunson, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.


Diffusion Coefficients Of Ethylene Glycol And Cyclohexanol In The Solvents Ethylene Glycol, Diethylene Glycol, And Propylene Glycol As A Function Of Temperature, Ronald D. Mitchell, James W. Moore, Robert M. Wellek Jan 1971

Diffusion Coefficients Of Ethylene Glycol And Cyclohexanol In The Solvents Ethylene Glycol, Diethylene Glycol, And Propylene Glycol As A Function Of Temperature, Ronald D. Mitchell, James W. Moore, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.


Organic Desorption From Carbon-I. A Critical Look At Desorption Of Unknown Organic Materials From Carbon, S. C. Allen, R. H. Pahl, Kenneth G. Mayhan Jan 1971

Organic Desorption From Carbon-I. A Critical Look At Desorption Of Unknown Organic Materials From Carbon, S. C. Allen, R. H. Pahl, Kenneth G. Mayhan

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.


Open-Channel Profiles By Newton's Iteration Technique, D. L. Fread, Terence E. Harbaugh Jan 1971

Open-Channel Profiles By Newton's Iteration Technique, D. L. Fread, Terence E. Harbaugh

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Computation of surface profiles for steady gradually varied flow can be accomplished by use of Newton's Iteration Technique. The magnitude of error is controlled and the profile depth can be conveniently calculated at selected distances upstream or downstream from a control point. A Fortran IV program is provided for utilizing the technique in a trapezoidal channel. © 1971.


Report On The School Of Mechanical Engineering National Technical Center Saigon, South Vietnam, Myrne R. Riley Jan 1971

Report On The School Of Mechanical Engineering National Technical Center Saigon, South Vietnam, Myrne R. Riley

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

"Training in the discipline of Mechanical Engineering is offered in South Vietnam by the School of Mechanical Engineering, one of four engineering schools and a Merchant Marine School composing the National Technical Center located presently in the Phu Tho region of Saigon, South Vietnam. The school was established in 1956 for the training of engineers, for mechanical and industrial activities. It became part of the National Technical Center, established by Decree No. 213-Gd by the President of the Republic of Vietnam on June 29, 1957 and graduated the first class of 20 in the summer of 1960. The KS Degree, …


Experimental Investigation Of Shock Boundary Layer Interaction For Two-Dimensional And Axisymmetric Flow, A. Shawki Zahran Jan 1971

Experimental Investigation Of Shock Boundary Layer Interaction For Two-Dimensional And Axisymmetric Flow, A. Shawki Zahran

Electronic Theses and Dissertations

A supersonic wind-tunnel has been constructed using an 8 inch by 10 inch single stage jet vacuum ejector with a capacity of handling 0.4 lb/sec air at 4 inches Hg absolute suction pressure. A Toepler Schlieren system with 10-inch diameter parabolic mirrors has been set up for flow pattern visualization. The same apparatus was developed to obtain multi-colored views of the flow pattern. That was accomplished by placing an equilateral prism in front of the light source located at the focal plane of the first parabolic mirror. A spectrum was thus produced at the focal plane of the second parabolic …


Screening Electrocardiograms Using Hotelling's Method Of Principle Components, Edward G. Schwartz Jan 1971

Screening Electrocardiograms Using Hotelling's Method Of Principle Components, Edward G. Schwartz

Electronic Theses and Dissertations

Considerable use is presently being made of computers to classify electrocardiograms (ECGs) into various heart defect categories. An example of such a program is the "Electrocardiographic Analysis Program" developed jointly by the Mayo Clinic and IBM. In one of Dr. Caceres published reports, he tells of using a computer program which involves 5,000 instructions. Dr. Caceres does not say whether this is a commercial program or one of bis own. His description does place this program in the same general category as IBM's. These programs have the common criteria of examining the ECG for the same information that a cardiologist …


Floating Bubble Configurations, Robert A. Medrow, B. T. Chao Jan 1971

Floating Bubble Configurations, Robert A. Medrow, B. T. Chao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The configurations of bubbles floating at a vapor-liquid interface are investigated both analytically and experimentally. The differential equations governing the shape of a single bubble at rest in a liquid of infinite extent are deduced under the assumption of zero dome thickness, uniform surface tension, and equal gas densities within the bubble and above the interface. These equations show that nondimensional bubble shapes depend upon the value of a single parameter. An analytical solution, valid for small bubbles, is developed and shown to be in good agreement with the general numerical solution. Good agreement with theory is demonstrated for floating …


Heat Transfer From An Oscillating Horizontal Wire, Bassem F. Armaly, D. H. Madsen Jan 1971

Heat Transfer From An Oscillating Horizontal Wire, Bassem F. Armaly, D. H. Madsen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The effect of vibration on heat transfer by natural convection has been investigated experimentally using a thin wire, 0.010 in. in diameter, and air as a convection medium. Horizontal reciprocating motion of varying amplitudes, peak-to-peak values of 0-2.655 in., and frequencies, 0-20 cps, was applied to an electrically heated horizontal wire. The average wire velocity (frequency times total path length traveled per cycle by the wire) was used to correlate and predict the experimental results. © 1971 by ASME.


Density Distribution Measurements In Rarefied Gases Contained Between Parallel Plates At High Temperature Differences, Darryl J. Alofs, Richard C. Flagan, George S. Springer Jan 1971

Density Distribution Measurements In Rarefied Gases Contained Between Parallel Plates At High Temperature Differences, Darryl J. Alofs, Richard C. Flagan, George S. Springer

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Density Distributions Were Experimentally Determined in Rarefied Gases at Rest Contained between Two Parallel Plates Maintained at Widely Different Temperatures. the Temperatures of the Hot and Cold Plates Were ∼79°K and ∼294°K, Respectively, Resulting in a Temperature Ratio of About 4:1. Both Helium and Nitrogen Were Used as Test Gases. Particular Attention Was Focused on Obtaining Data in the Temperature Jump and Transition Regimes. the Gas Densities Were Measured by Observing the Luminescence Produced by a High-Energy Electron Beam Traversed between the Plates. in Addition to the Density Measurements, Heat Transfer Measurements Were Also Made in Order to Estimate the …


The Axial Contact Of Finite Elastic Cylinders With Application To Thermal Contact Resistance, Ross Orlo Mcnary Jan 1971

The Axial Contact Of Finite Elastic Cylinders With Application To Thermal Contact Resistance, Ross Orlo Mcnary

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Predictions of the macroscopic thermal contact resistance have been severely restricted because the macroscopic contact area between finite members could not be determined. A new method of solution to this contact problem in elasticity is developed which is applicable to a wide variety of geometries and boundary conditions. A physical lumped-parameter model is employed from which the finite difference equations in terms of displacement are derived. Calculations using this method indicate that large errors in the prediction of the thermal contact resistance can result if solutions for bodies of infinite extent are employed for finite regions of interest. Especially large …


Operational Effects Of Auto-Utility Trailer Combinations On Rural Highways In Kentucky, Bruce S. Siria Jan 1971

Operational Effects Of Auto-Utility Trailer Combinations On Rural Highways In Kentucky, Bruce S. Siria

Kentucky Transportation Center Research Report

An analysis of accident records indicated that A-UT combinations are involved in a disproportionately high number of traffic mishaps. Locations which have a history of accidents involving A-UT vehicles indicated that differential crosswinds and unanticipated driving maneuvers contribute to driver loss of control. A-UT combinations contributed to the fatigue loss in pavement life approximately 50 percent as much as single-unit, two-axle, six-tire trucks (per vehicle). In general, this vehicle type constituted approximately three percent of the total traffic stream. Analysis of speed distributions indicated an equivalency factor for A-UT combinations equal to that for trucks for similar roadway types and …


The Anodic Dissolution Reaction Of Insb: Etch Patterns, Electron Number, Anodic Disintegration, And Film Formation, Martin E. Straumanis, Lih Da Hu Jan 1971

The Anodic Dissolution Reaction Of Insb: Etch Patterns, Electron Number, Anodic Disintegration, And Film Formation, Martin E. Straumanis, Lih Da Hu

Materials Science and Engineering Faculty Research & Creative Works

The etching behavior of the inverse {111} planes of undoped, semiconducting, n-type, InSb single crystals was explored. Depending upon the etchant, including anodic dissolution, various etch patterns were obtained on the inverse planes. In general, the etch pits on the In{111} plane were round, and the face was shiny, whereas the face of the inverse plane was dark and rough. The rates of dissolution in the electrolytes used were very low, especially in absence of oxidizers. The components dissolve as In3+ and Sb3 +. At current densities above 40 or 60 mA cm-2 (on Sb{111} or In{111}), growth of a …


A Magnetic Aftereffect In Dilute H.C.P. Co-C Alloys, J. R. Keiser, Manfred Wuttig Jan 1971

A Magnetic Aftereffect In Dilute H.C.P. Co-C Alloys, J. R. Keiser, Manfred Wuttig

Materials Science and Engineering Faculty Research & Creative Works

A magnetic Dis accommodation in dilute h.c.p. Co-C alloys has been observed around 90°C. The thermally activated process giving rise to the Dis accommodation is characterized by an activation energy of 26 kcal mole-1 and an attack frequency on the order of 10+13 sec-1. An application of the selection rules shows that the Dis accommodation cannot be caused by the redistribution of tetrahedral or octahedral interstitials or any nearest neighbor interstitial pairs as long as the defects interact linearly with the internal magnetic field. © 1971.


Charges On Jet Drops Produced By Bursting Bubbles, Robert A. Medrow, B. T. Chao Jan 1971

Charges On Jet Drops Produced By Bursting Bubbles, Robert A. Medrow, B. T. Chao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The sizes and charges of jet drops produced by bursting air bubbles are examined experimentally. The variation in charge for bubble lifetimes of up to 200 sec in NaCl and KCl solutions is reported. Jet drops refer to drops produced by a jet rising from a cavity left in a liquid surface by a bursting bubble; bubble lifetime is the interval during which a bubble is in motion between generation and rupture. With other variables held constant, drop charge shows a characteristic variation of a rise to a maximum followed by a decrease to an asymptotic value, as bubble lifetime …


An Evaluation Of An Aerated Lagoon System Treating Combined Dairy And Domestic Wastes During Summer Operation, Douglas M. Skie Jan 1971

An Evaluation Of An Aerated Lagoon System Treating Combined Dairy And Domestic Wastes During Summer Operation, Douglas M. Skie

Electronic Theses and Dissertations

The Water Quality Act of 1965 and the adoption of the subsequent state water quality standards emphasized the general public's concern for the control of water pollution; for it has become the goal of our nation to maintain all American waters in a suitable condition for domestic and industrial supply, for recreation and for other beneficial uses. It is for these reasons that many communities have been faced with the problem of constructing new sewage treatment facilities or expanding present operations. The use of stabilization ponds as a means of providing sewage treatment has been the practice of many small …


Finite Difference Solutions Of Axisymmetric Infiltration Through Partially Saturated Porous Media, Chi-Yuan Wei, Roland W. Jeppson Jan 1971

Finite Difference Solutions Of Axisymmetric Infiltration Through Partially Saturated Porous Media, Chi-Yuan Wei, Roland W. Jeppson

Reports

Solutions are obtained to the problem of steady-state partially saturated infiltration of moisture applied over a horizontal source circle which moved through homogeneous soils toward a water table. A commonly accepted relationship between relative permeability and capillary pressure has been utilized in conjunction wit Darcy’s law to formulate the mathematical model. The solutions have utilized an inverse formulation and have been obtained by finite difference. The inverse formulation considers the magnitudes of the cylindrical coordinates r and z as the dependent variables and the potential function and the Stokes’ stream function as the independent variables (i.e the problem is solved …


The Behavior Of Pvc Pipe Under The Action Of Water Hammer Pressure Waves, Gary Z. Watters Jan 1971

The Behavior Of Pvc Pipe Under The Action Of Water Hammer Pressure Waves, Gary Z. Watters

Reports

Introduction: Hydraulic transients, commonly referred to as water hammer, occur in a hydraulic system whenver the velocity of flow in any one of the pipes in the system is caused to change. The magnitude of the pressure waves generated by a given change in velocity depends on the geometry of the pipe system, the magnitude of the velocity change and the elastic wave velocity in the system componenets. In turn, the elastic wave velocity depends on the modulus of elasticity of the fluid and the pipe material, the size and thickness of the pipe, the method by which the pipe …


Development Of A Procedure For Determining Spacial And Time Variations Of Precipitation In Venezuela, Luis E. Ramirez Jan 1971

Development Of A Procedure For Determining Spacial And Time Variations Of Precipitation In Venezuela, Luis E. Ramirez

Reports

An analysis of the influence of the length of the record in the reliability of mean values of precipitation was made for the Caracus-Cagigal Station in Venezuela. Ten series of values were obtained for 10, 15, 20, 25, 30, and 35-year periods, extracted for sliding intervals for the overall record of 75 years. The reliability of mean values computer from Figure 3 was quite low for 10, 15, and 20- year periods. The long term record means had higher reliability, increasing with the number of years in the records, but the differences are not important in terms of accuracy. Precipitation …


Water Resources Planning And Social Goals: Conceptualization Toward A New Methodology, D. Peterson, H. Caulfield, R. D'Arge, D. Gordon, M Marts, T. Roefs, R. Roelofs Jan 1971

Water Resources Planning And Social Goals: Conceptualization Toward A New Methodology, D. Peterson, H. Caulfield, R. D'Arge, D. Gordon, M Marts, T. Roefs, R. Roelofs

Reports

A modeling concept relating water resource use to


Inverse Solutions To Three-Dimensional Free Surface Potential Flows, Roland W. Jeppson Jan 1971

Inverse Solutions To Three-Dimensional Free Surface Potential Flows, Roland W. Jeppson

Reports

Methods are developed and defined for obtaining numerical solutions to three-dimensional, free surface, invisvid, incompressible fluid flows and three-dimensional free surface Darcian flow in porous media. Since those boundaries consisting of free surface are unknown a priori, a solution to the space boundary value problem resulting from a formulation in the physical space is very difficult, if not impossible, to obtain. Consequently, the methods described herein are based on a formulation in a space defined by a potential function and two mutually orthogonal stream surfaces whose intersections define the streamlines of the flow. In this space the positions of free …


The Effect Of Carbon On Algal Growth--Its Relationship To Eutrophication, Joel C. Goldman, Donald B. Porcella, Joe E. Middlebrooks, Daniel F. Toerien Jan 1971

The Effect Of Carbon On Algal Growth--Its Relationship To Eutrophication, Joel C. Goldman, Donald B. Porcella, Joe E. Middlebrooks, Daniel F. Toerien

Reports

Introduction: Natural and cultural eutrophication (enrichment with nutrients) frequnetly results in excessive algal growths thereby reducing the beneficial uses of surface waters (Hasler, 1947; Thomas, 1955, Edmondson et al., 1956, Oswald and Golueke, 1966, Skulberg, 1967, Mackenthun et al., 1968, Goldman and Armstrong, 1969, McGauhey et al., 1968,1969, 1970a, 1970b). Recent reviews emphsize that the prevention of further reduction in the quality of water resources requires the implementation of effective control measures (Goldman, 1965, Steward and Rohlich, 1967, Middlebrooks et al., 1969, Rohlich, 1969). Effective control of cultural eutrophication must involve the manipulation of those factors which affect algal growth, …


Application Of Operations Research Techniques For Allocation Of Water Resources In Utah, Calvin G. Clyde Jan 1971

Application Of Operations Research Techniques For Allocation Of Water Resources In Utah, Calvin G. Clyde

Reports

In this report a methodology is described for determining the optimal allocation of water supplies in the State of Utah to minimize the cost of meeting an assumed set of water requirements. A linear programming model was formulated to represent the ten interconnected hydrologic study areas of the state. The comprehensive model considers virtually all uses, areas, sources, transfers and costs of water. The model has 204 constraints and 3378 variables and was solved by the simplex method. Included in the results are the following: the optimal water allocation or the groundwater, surface water, and water transfers which minimize the …


Further Studies Of The Optimum Operation Of Desalting Plants As A Supplemental Source Of Firm Yield, Calvin G. Clyde, Wesley H. Blood Jan 1971

Further Studies Of The Optimum Operation Of Desalting Plants As A Supplemental Source Of Firm Yield, Calvin G. Clyde, Wesley H. Blood

Reports

The Operating Rule Program was developed in an earlier study to furnish a means to determine optimum desalting plant size, optimal operating rule, and costs of operating in conjunction with existing water supply systems, under the present study, five further objectives were accomplished: (1) The program was applied to a New York City water supply system feasibility study in connection with a dual purpose nuclear power plant to develop costs for adding firm yield to the New York City water supply system in conjunctive operation with the desalting plant. (2) The program was modified to enable assessment of stage construction …


Development Of Cold Cloud Seeding Technology For Use In Precipitation Management, Charles F. Chappell, Joel E. Fletcher, George W. Reynolds, William N. Mcneill, Ronald Campbell Jan 1971

Development Of Cold Cloud Seeding Technology For Use In Precipitation Management, Charles F. Chappell, Joel E. Fletcher, George W. Reynolds, William N. Mcneill, Ronald Campbell

Reports

This is a report of the world accomplished and results obtained under a 2-year contract. The primary objective of the Wasatch Weather Modification Project is to assess the effectiveness of selected procedures for increasing the water supply in the Wasatch Mountains by cloud seeding. As part of this overall objective, an airborne seeding experiment has been conducted for two winter seasons. Preliminary results of this experiment indicate a positive seeding effect within and on the periphery of the designated target area. A summary of project designs, procedures, and problems encountered is also included. Data processing, editing, analysis and display procedures, …


The Detection Of Magnetic Fields Caused By Groundwater, Duane G. Chadwick, Larry Jensen Jan 1971

The Detection Of Magnetic Fields Caused By Groundwater, Duane G. Chadwick, Larry Jensen

Reports

Perturbations on the earth’s magnetic field may coincide with the existence of groundwater. Theoretical calculations are made showing how and to what extent this effect may exist. The suggestion is also made that water dowsers may get a dowsing reaction as a result of entering a change in magnetic gradient. Tests were conducted to determine the statistical significance of dowsing reactions obtained by separate individuals dowsing in a common test area. Approximately 150 people participated in the experiment over a period of one year. Chi-square tests showed considerable statistical significance. Virtually all people tested experienced dowsing reactions though most of …


A Computerized Method Of Precipitation Data Quality Control, Ronald H. Campbell Jan 1971

A Computerized Method Of Precipitation Data Quality Control, Ronald H. Campbell

Reports

A computerized data quality check and data edit program has been developed to aid in the processing of telemetered precipitation data. The logic considerations and program development are discussed and results are displayed. This effort has resulted in successful editing of large amounts of precipitation data gathered by automated remote data acquisition techniques. The application of this processing routine has resulted in reducing data editing costs to about three percent of that required to do the work manually.