Engineering Commons^™

A Predictive-Adaptive, Multipoint Feedback Controller For Local Heat Therapy Of Solid Tumors, Charles F. Babbs, V A. Vanguine, J T. Jones

Weldon School of Biomedical Engineering Faculty Publications

Uniform heating of tumor tissue to therapeutic temperatures without damaging surrounding normal tissue is required for optimal local heat therapy of cancer. This paper describes an algorithm for online computer control that will allow the therapist to minimize the standard deviation of measured intratumoral temperatures. The method is applicable to systems incorporating multiple surface and/or interstitial applicators delivering microwave, radiofrequency, or ultrasonic power and operating under the control of a small computer. The essential element is a novel predictive-adaptive control algorithm that infers relevant thermal parameters from the responses of multiple temperature sensors, as each of the power applicators is …

Latent And Sensible Load Distributions In Conventional And Energy Efficient Residences. Final Report, January 1983 - January 1986. 05-86., Florida Solar Energy Center, Alp Kerestecioglu

FSEC Energy Research Center®

To develop a method to characterize the cooling load distributions in conventional and energy efficient residences, specifically as related to building dehumidification loads, as they pertain to the potential for the use of gas-fired dehumidification and cooling equipment.

Two-Step Optimal Thermal Generation Scheduling, B Fardanesh, F. Eugenio Villaseca

Electrical and Computer Engineering Faculty Publications

A new approach to the solution of the optimal thermal generation scheduling problem is presented. The problem is solved in two steps. As a first step, the optimal production schedule for the next day is obtained based on a daily load forecast, reserve capacity requirements, and present status of generating units. The second-step algorithm uses the results of the first step and adjusts the previous schedule to meet new constraints developed during the course of the day. Variable truncation dynamic programming is proposed as a new method to reduce computation effort. To eliminate the need for solving the …

Clostridium Perfringens: An Adjunctive Indicator In Nonpoint Pollution, Steven G. Eberl

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Clostridium perfringens (CP) was evaluated as an additional indicator in assessing impacts and sources of microbial pollution in the Idaho-Utah Cache Valley. Point, nonpoint, river water, and animal fecal samples were analyzed for CP, total coliforms, fecal collforms, and fecal streptococci.

Monthly river samples consistently contained < 20 CP/100 mL, but concentrations of the other indicators varied significantly by location and date. Two sample stations consistently had CP concentrations greater than 20/100 mL. One of these stations was influenced by an upstream wastewater discharge. Chlorinated effluent from this trickling filter plant contained greater than 10³ CP/100 mL, but met a 400 FC/100 mL discharge standard. A consistent decrease in CP concentrations in samples taken downstream from this wastewater source were found, despite significant impact from adjacent nonpoint pollution. Lagoon and oxidation ditch wastewater effluents sampled contained < 20 CP/100 mL.

Nonpoint sources sampled (e.g., cattle feedlot runoff) contained < 20 CP/100 mL and 10²-10⁴/100 …

The Vertical Distribution Of Salts In A Soil Profile During The Drainage Process, Adel Taha Yassin

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The purpose of this study was to develop a model to predict water extraction patterns and therefore salt distribution patterns in a one dimensional homogeneous soil profile for a specified root distribution.

Water extraction was simulated as a function of the total potential and the root density at any level of the profile.

Salt redistribution caused by irrigation was simulated by assuming a partial and proportional displacement of the water in each soil layer.

A computer program was written for the model in Fortran language and implemented on the Vax. To evaluate the performance of the model, test studies were …

Aerating Butterfly Valves To Suppress Cavitation, R. Ted Davis

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Proper aeration of cavitating hydraulic equipment can greatly reduce cavitation intensity, noise, and damage. This thesis quantifies the benefit, in terms of damage and noise, from aerating six inch butterfly valve. The incipient damage level of cavitation was obtained for both aerated and non-aerated conditions. The level is defined as one pit per square inch of a soft aluminum test specimen per one minute of operation. A description of the cavitation pits that occurred plus where they appeared is presented. A graph showing the aerated and non-aerated limits of incipient damage is given along with a table showing the percent …

Irish H & V News

Building Services Engineering

No abstract provided.

Dod6420.1-R, Organization And Functions Of The Armed Forces Medical Intelligence Center (Afmic), April 1986, U.S. Department Of Defense, Robert Bolin , Depositor

United States Department of Defense Military Intelligence

This is the charter for a national-level medical intelligence agency. Specifically, the AFMC was a joint agency of the Military Departments … under the management of the Secretary of the Army…” This directive spells out the mission, functions, responsibilities, and management of the center. An Interdepartmental Advisory Panel (IAP) made recommendations to the Secretary of the Army concerning the director and officers serving at the AFMIC.

The directive contains a lengthy list of acronyms and detailed definitions.

The directive discusses close cooperation with Canada, the United Kingdom, and Australia through a Quadripartite Medical Intelligence Committee (QMIC) headquartered in Washington, DC. …

Test 1591: John Deere 4050 Powershift Diesel 15-Speed (Chassis S/N Rw4050p006510 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1589: John Deere 3150 And 3155 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1590: John Deere 4050 Quadrange Diesel 16-Speed (Chassis S/N Rw4050h006510 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Bulletin - April, 1986, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A six page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Deposition Of Suspensions In Convergent Channels Due To Electrostatic Image Forces, Kwok Wah Hui

Dissertations

The deposition of suspensions for uniform flow in convergent channels under the combined influences of inertia, viscous and electrostatic image forces was studied theorectically. The fluid phase was assumed to be two-dimensional, steady, uniform, incompressible and laminar while the particle phase was assumed to be uniform, steady, dilute and with negligible gravity effects.

Since the image force equations for convergent channels have not been derived, it becomes one of the main purposes of this study to perform the derivation of the image force equations. The lengths of the channels were chosen in a way that the exit area is only …

Reactions Of Chlorocarbon Species With Hydrogen Over Palladium On Alumina Catalyst And Zeolite Catalyst-Development Of Deactivation Models, Yuh-Der Yang

Dissertations

Four catalytic dechlorination reactions were studied experimentally using a fixed-bed reactor at atmosphere pressure. Reaction mechanisms were proposed, and the kinetics modelled.

The first reaction is 1,2-dichloroethane with hydrogen over zeolite catalyst. Catalyst deactivation models were examined.

The second reaction was between 1,2-dichloroethane and hydrogen over palladium catalyst on alumina support. Formation of two intermediates on the catalyst surface is proposed, which then produced ethane, ethylene, and ethyl chloride. Higher conversion to ethane and ethylene was observed at temperatures above 218°C while conversion to chloroethane is higher at temperatures below 218°C. The activation energy was found to be 15 Kcal/gm-mole. …

Deposition Of Particles In Tubes Due To Gravity And Electrostatic Charges, Win-Chung Chen

Dissertations

The deposition of particles in a parallel-plate channel and a circular tube under the influence of inertia, fluid viscosity, gravity and electrostatic image forces was studied by analytical and numerical methods. A laminar flow with uniform and parabolic velocity profiles was investigated with a particle initial velocity of zero as well as that of the local fluid velocity.

The governing equations were solved by the Lagrangian approach to obtain the particle trajectories from which the fraction of deposition was calculated. Closed form solutions for particle trajectory and a complete deposition of particles in a finite length of the flow passage …

Computer Aided Stress Analysis Of Long Bones Utilizing Computed Tomography, Shlomo Asher Marom

Dissertations

A computer aided analysis method, utilizing computed tomography (CT) has been developed, which together with a finite element program determines the stress-displacement pattern in a long bone section. The CT data file provides the geometry, the density and the material properties for the generated finite element model.

A three-dimensional finite element model of a tibial shaft is automatically generated from the CT file by a pre-processing procedure for a finite element program. The developed pre-processor includes an edge detection algorithm which determines the boundaries of the reconstructed cross-sectional images of the scanned bone. A mesh generation procedure then automatically generates …

Acuta Enews April 1986, Vol. 15, No. 4

ACUTA Newsletters

In This Issue

President's Message

Party Line

Telecom Department Compensation: 1985

System 86 Cutover at Cornell

Selling

Spring 1986, Wmpg 90.9 Fm

WMPG Program Guides

WMPG program guide for Spring 1986

Includes notes from Program Director, information on shows and events, and schedule.

Spring 1986, 90.9 Wmpg Fm

WMPG Program Guides

Trifold, light blue, Spring 1986

Two And Three-Dimensional Isoparametric Finite Elements For Axisymmetric Micropolar Elasticity, Fuang-Yuan Huang

Dissertations

Finite element analysis program for isotropic and orthotropic axisymmetric micropolar (Cosserat) elastic solids are developed in this thesis. Isoparametric elements of 8- and 20- node are used to solve general three-dimensional problems, arid both 4- and 8-node elements are used for two-dimensional cases. Three-dimensional finite element formulation for cylindrical coordinate system is derived. Corresponding Fortran programs are then developed. Patch tests are performed for two-dimensional cases to verify the applicability of the finite element method to non-rectangular geometries. Several two-dimensional and three- dimensional problems for micropolar elastic solids are solved to verify the formulations arid computer program.

Good agreements were …

Free-Form Deformations In A Constructive Solid Geometry Modeling System, Scott R. Parry

Theses and Dissertations

No one will question that computers are revolutionizing the design industry. It is pointed out in [Bezier84] that before CAD/CAM, a surface was defined by tracing cross sections on a drawing and then carving these sections in wood, plastic or metal. The final model was determined by someone interpolating between the sections. This labor intensive art is being replaced by techniques of computer aided geometric design.

Effects Of Load Distributions And Axle And Tire Configurations On Pavement Fatigue, Herbert F. Southgate, Robert C. Deen

Kentucky Transportation Center Research Report

Damage factor relationships for axle and tire configurations are presented. Adjustment factors are provided to account for variations in load distributions within axle groups, distances between axles of a tandem, and variations in tire pressure for both dual and flotation tires.

Properly accounting for accumulated fatigue of a pavement requires a traffic volume, proportions of vehicle styles (classifications) within the of service, estimate of the average damage factor for each classification, reasonable measure of traffic stream, dates and estimates of tire contact pressures.

All adjustment factors presented are based on analyses of a limited number of structures and should be …

Use Of Nondestructive Testing To Prevent Failures Of In-Service Metal Bridges, Theodore Hopwood Ii, Robert C. Deen

Kentucky Transportation Center Research Report

The failure of metal bridges, subject to in-service fracture problems mainly caused by fatigue, may be prevented or minimized by performance of periodic nondestructive testing. Attendant factors that justify funding for such inspections include the potential for bridge failure, the consequences of bridge collapse, risk analyses, and inspection strategies. Factors that affect structural integrity include structural design, construction quality, and service loadings.

Details of a computer/strain-gage system capable of obtaining strain-gage data from critical structural elements are described. Data are processed to determine the stress-range distribution, number of stress cycles, resolved mean stress range, need for structural inspection, critical crack …

Documentation For 1986 Weight-Distance Tax Analyses Using Lotus 1-2-3, Herbert F. Southgate

Kentucky Transportation Center Research Report

No abstract provided.

Evaluation Of A Full-Depth Asphaltic Concrete Pavement, Herbert F. Southgate, Gary W. Sharpe, Mark Anderson

Kentucky Transportation Center Research Report

This study was initiated to verify a newly-developed set of design curves for full-depth asphaltic concrete pavements. Quality control during construction was checked using nuclear density testers, Benkelman beams, and a Road Rater. During the course of this study, an analysis system (predicated upon the elastic theory model) was developed to interpret the dynamic deflections as measured by the Road Rater. The thickness design curves were verified by elastic theory and deflection testing within the accuracy of construction variations.

Measured rut depths were analyzed in terms of potential rut depth resulting from consolidation under traffic due to lack of obtaining …

Nondestructive Evaluation Of Rigid Pavements Using Road Rater Deflections [1986], Gary W. Sharpe, Mark Anderson, Robert C. Deen, Herbert F. Southgate

Kentucky Transportation Center Research Report

Dynamic deflections have been used to determine in-place structural conditions of rigid pavements, based on modifications of principles and experience with the structural evaluation of flexible pavements. Details of the use of elastic layer theory to simulate deflection measurements associated with loadings for the Kentucky Road Rater are presented. Included is an illustration of the use of field deflection measurements to "back calculate" in-place moduli. The procedures are generally iterative and involve matching measured deflections with theoretical deflections. Elastic layer principles have been used to simulate deflections only at the mid slab position. Relationships regarding deflections at other locations on …

Stability Of Embankments On Clay Foundations, Tommy C. Hopkins

Kentucky Transportation Center Research Report

Ninety-one well-documented geotechnical failures are reviewed. The case studies involved the failure of embankments, footings and load tests, excavated slopes, and natural slopes. Seventy-five of the geotechnical failures had been analyzed using total stress analysis. Sixteen of the case failures had been analyzed using effective stress analysis. Based on a review of these case studies, there are discrepancies between predicted and actual stabilities of geotechnical structures and there is a tendency tu overestimate the factor of safety. Differences that may arise between predicted and actual performances are discussed and examined and guidelines are proposed for evaluating the potential of successfully …

Use Of Post Delineators On Interstates, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objectives of this report were to investigate 1) the potential benefits of using flexible posts for post delineators and 2) the possibility of not requiring post delineators on sections of interstate-type highways where recessed markers are installed.

It is recommended that post delineators should only be used when the design curvature is 1.5 degrees or more, and the spacing should be based on the formula given in Table III – 1 of the MUTCD. Data obtained concerning the performance of flexible posts do not support widespread use at this time. A testing program should be developed to obtain an …

Treatment Of Narrow Medians On Four-Lane Rural Roadways, Jerry G. Pigman, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objective of this study was to investigate alternatives to paved mountable medians that have been used in the past on sections of four-lane, partially controlled access roads where right-of-way is restricted. These mountable medians present obvious operational problems due to the 3-inch difference in height as compared to the through lanes. In addition, construction and maintenance problems are associated with mountable medians because of the height differential.

A telephone survey of 16 states was conducted to determine their policy for separation of rural four-lane roads with partial control of access and narrow medians. Accident analyses comparing roads in Kentucky …

A Unit Of Instruction In Fiber-Optic Communication, Ronald Struble

Graduate Research Papers

The purposes of this research project were to:

1. Review the historical developments, components, and applications of optical fiber in communications.

2. Develop a laboratory exercise to demonstrate fiber-optic communication.

3. Construct equipment to demonstrate the use of fiber optics in communication. This equipment is used in the laboratory exercise.