Engineering Commons^™

A Closed Form Image Force Function For Deposition Of Particles In A Cylindrical Tube, Hsi-Chung Chiou

Theses

This study investigated the behavior of charged particles suspended in a laminar steady incompressible flow in a cylindrical tube under the influences of image , inertia , viscous and gravitational forces. A new expression for the image force was obtained by introducing an approximate potential energy function. The velocity profiles employed in the analysis were uniform and parabolic.

The governing equations derived were based on Newton's second law of motion and were solved by a Runge-Kutta numerical method. The results were obtained for different values of Q, a dimensionless inertia-charge parameter. For a value of Q equal to zero the …

On Torsional Spring Constants At The Juncture Of Piping-Nozzle, Shean-Juinn Chiou

Theses

Numerical results of torsional spring constants at the juncture of piping-nozzle are studied in this thesis by using the "ANSYS" program and run on VAX computer. These results are presented in tabulated form for a piping-nozzle vessel with constant thickness of 0.375 in. Plot for the torsional spring constants in terms of beta (nozzle radius/pipe radius), gamma (pipe radius/thickness) and alpha (pipe length/radius) are also presented in this thesis. These data are under zero piping internal pressure with beta ranging from 0.1 to 0.8, and gamma ranging from 10 to 150. A numerical example with verification is also given.

Design And Optimization Of Nmos Sense Amplifiers For Vlsi Drams, Nimish K. Shah

Theses

The aim of this thesis is to study and optimize the performance of NMOS sense amplifiers used in modern VLSI DRAMs.

Initially dynamic memory cells and popular sense amplifier circuits are surveyed.

A standard five transistor sense amplifier is later chosen for detailed analysis. Layout of the circuit is drawn to get the physical parameters. Using SPICE simulator, various effects of circuit parameters are studied. From these results optimal values of these parameters are arrived at.

Also an effort is made to derive theoretically equations for the latching time of a post amplifier which is the most important part in …

The Stress Distribution Of The Frp Pressure Vessel By Using Ansys Program, Lung-John Tsai

Theses

The objective of this paper is to take advantage of a general purpose finite element computer program, called ANSYS, to analyze the surface stress distribution of a fiber reinforced plastic (FRP) laminated composite pressure vessel. The vessel is subjected to internal pressure, which is assumed to be constant over the interior surfaces.

In this paper, the material is assumed to be orthotropic, and the stress-strain relationship linear.

A FRP pressure vessel subjected to an Internal pressure, 6.895 MPa (1000 psi), is taken as an example. The results show that this approach compares well with a theoretical solution.

An 8052 Ah - Basic, Based Development System, Suresh Vishwanath Leley

Theses

This project exploits the latest in microcontrollers-an entire environment for developing and prototyping a microcontroller application. With one key chip, a little glue, and a Dumb terminal a powerful system is achieved at a vanishingly small cost. This "one chip" system is adequate for realizing a wide range of applications calling for a small computer or an embedded processor.

Besides economy of system cost, the turn around time from concept to functioning application can be extremely short, even when the development engineer is not particularly well acquainted with traditional assembly language and microprocessor development practices. This economy is achieved by …

An Analysis Of Minimum Shift Keying From The Viewpoints Of Quadrature Multiplexed And Multi-H Continuous Phase Modulation Signaling, Alfred Anthony De Seta

Theses

Minimum Shift Keying (MSK) is a bandwidth efficient modulation scheme which offers superior performance over Quadrature Phase Shift Keying (QPSK) and Offset Quadrature Phase Shift Keying (OQPSK). This paper discusses these modulation techniques from a quadrature multiplexed signaling viewpoint and compares them in terms of error performance, bandwidth properties and bandlimiting and hardlimiting effects. MSK is also considered as a special case of a multi-h Continuous Phase Modulation (CPM) signal and the Viterbi algorithm is presented as an optimal detection scheme for this class of signals. A computer simulation is performed with the VA as the detection mechanism for an …

A Computer Aided Manufacturing System For Small Quantity Prototype Board Production, Santiago Garcia-Perez

Theses

A matrix addressed manufacturing tool has been built, tested, and integrated in a system aimed to exploit wire-wrap wiring technology for protoboard production in small quantities. Extensive software exploits the power and economy of the personal computer as a superb manufacturing tool and documentation system. Computer graphics are used as a visual aid that takes advantage of the cognitive capabilities of the human mind and eliminates the boredom and high costs involved with heavy automation achieving instead a tolerable level of human engagement with significantly increased efficiency. The approach presented is new and delivers substantial gains in productivity. The software …

Modelling Of Pile Load Tests In Weak Rock, Daniel Walter Caruso

Theses

The purpose of this thesis was to investigate the loss of load capacity of relaxed pile groups driven into weak bedrock. This was accomplished in the laboratory using a dynamic driving apparatus equipped with a static load testing system. The static load testing system applied loads hydraulically, and the load settlement behavior was monitored using an electronic load cell and a linear variable differential transducer (LVDT).

Tests were performed using 1" diameter steel pipe piles driven in a five pile group pattern at spacings of two diameters and four diameters. Piles were driven into a simulated rock mass consisting of …

Pressure Drop In A Strainer Element By The Finite Element Method, Wei-Long Chen

Theses

The pressure drop in a strainer element which consists of a channel and a diffuser has been investigated by the finite element method and the semi-empirical analysis.

An existing finite element program, FEM2D using the penalty parameter model, was employed. It was found that the range of Reynolds numbers in the strainer element was 0.193 to 4.824. For the pressure drop in the channel, the finite element method is in agreement with the analytical solution. For flow in the diffuser, the finite element method failed to give satisfactory results due to flow separation.

Realization And Implementation Of A Recursive Digital Convolution Algorithm In Cmos, Lik Tang Cheng

Theses

This thesis describes the implementation of a digital convolver. A recursive digital convolution algorithm was realised and implemented by using CMOS circuitry. This thesis also gives a technical overview of current CMOS processing technologies as well as various novel CMOS logic circuit techniques.

Preparation And Kinetic Study Of Immobilized Enzyme Catalyst, Sanjiv S. Kuray

Theses

Degradation of commercially available immobilized Glucose Isomerase enzyme was studied in a batch reactor. Effect of shearing on the degradation was studied by comparing the performance of a basket type reactor ( with enzyme kept inside the stirrer) and ordinary batch reactor ( with enzyme kept outside the stirrer).

Invertase enzyme is available commercially in a free soluble form. It was coupled with a new kind of starch derivative. The coupling efficiency achieved was 8.7 % and the concentration of the immobilized enzyme was 718 U invertase per gram of starch. The deactivation of enzyme-starch gel was studied in a …

The Conversion Of The Process Flowsheet Simulator, Flowtran, For Fortran 66 Based Mainframe Computers, Timothy Edward Roche

Theses

The process flowsheet simulator FLOWTRAN was converted from FORTRAN 77 code to FORTRAN 66 code. The conversion was accomplished by developing a number of subprograms to handle FORTRAN 77 intrinsic functions that are missing in the FORTRAN 66 standard and by altering the code to take advantage of the developed subprograms. Also developed were a set of procedure files for executing the FORTRAN 66 FLOWTRAN on a Sperry-Univac 90/80-4. The new FLOWTRAN was tested and performs identically to the FORTRAN 77 version. The FORTRAN 66 FLOWTRAN can be installed on any mainframe computer with a FORTRAN 66 compiler.

Implementation Of Finite Element Method On A Microcomputer, Chi-Yuang Huang

Theses

A finite-element program FEM2D has been implemented on a PHILIPS microcomputer. The program has a generation preprocessor and thus makes finite-element analysis on a microcomputer considerably easier than before, since it allows models to be created and edited much faster than by manual method. The interactive program FEM2D prompts the user to input data directly from the screen. It is convenient for the user, both in teaching and learning.

The FEM2D is a two-dimensional finite-element program capable of solving two-dimensional problems, such as plane elasticity, heat transfer and imcompressible fluid flow problems. It is developed with a formulation of a …

Infiltration Into Decomposed Granite Soils; Numerical Modeling, Applications And Some Laboratory Observations, A. W. Jayawardena, Jagath J. Kaluarachchi

Civil and Environmental Engineering Faculty Publications

This paper describes the outcome of a study on rain infiltration into decoposed granite which is one of the two main types of soils found in Hong Kong. It consists of the development and verification of a finite element based numerical model which has general applicability for flow through unsaturated porous media, application of the model for predicting moisture movement in an artificial slope made out of reconstituted decomposed granite and some laboratory observations including the estimation of soil hydraulic parameters.

Test 1596: Kubota M6030dt And M6030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1594: Kubota M4030dt And M4030 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1595: Kubota M5030dt And M5030 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1592: Steiger Bearcat 1000 12-Speed (Caterpiller Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1593: Steiger Couger 1000 12-Speed (Caterpiller Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

A Procedure For Testing Cored Ice Under Uniaxial Tension, Russell W. Lee

Dartmouth Scholarship

A procedure is described for testing cored ice specimens under uniaxial tension. The procedure incorporates an end-capping system described by Cole and others (1985), two carpeted Synthane end caps, and extensometers mounted directly on the ice. Use of the procedure has resulted in a successful test rate of 75%

Development Of A Unified Approach To The Design Of Cold-Formed Steel Members (Draft), Teoman Peköz

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Dynamic Deformation Of Volcanic Ejecta From The Toba Caldera: Possible Relevance To Cretaceous/Tertiary Boundary Phenomena, Neville L. Carter, Charles B. Officer, Craig A. Chesner, William I. Rose

Department of Geological and Mining Engineering and Sciences Publications

Plagioclase and biotite phenocrysts in ignimbrites erupted from the Toba caldera, Sumatra, show microstructures and textures indicative of shock stress levels higher than 10 GPa. Strong dynamic deformation has resulted in intense kinking in biotite and, with increasing shock intensity, the development in plagioclase of planar features, shock mosaicism, incipient recrystallization, and possible partial melting. Microstructures in quartz indicative of strong shock deformation are rare, however, and many shock lamellae, if formed, may have healed during post-shock residence in the hot ignimbrite; they might be preserved in ash falls. Peak shock stresses from explosive silicic volcanism and other endogenous processes …

Acuta Enews May & June 1986, Vol. 15, No. 5 & 6

ACUTA Newsletters

In This Issue

President's Message

Party Line

Illinois Universities

Simplified Message Desk Interface

Pro & Con: Should Users Keep Network Control In-House?

DMI or CPI: Who will win?

Committed To Telecommunication Excellence

Look Boss, No Coax!

Design And Applications Of A Graphics Package For The Hp1000 Computer., Hsiao-Chih George Lee

Electronic Theses and Dissertations

The objective of this thesis is to develop the FORTRAN subroutine PLOTER which is a general-purpose plotting tool to plot charts on a Hewlett Packard plotter. The programs RESP and INVLAP which can plot the frequency and time responses of system functions are modified to adopt the PLOTER subroutine and are stored of the HP1000-A900 minicomputer whose software, the GRAPHICS/1000, supports the graphics ability of PLOTER. This thesis describes the theories, functions, software techniques and operations of the PLOTER subroutine and the application programs RESP and the INVLAP. It also provides program listings and example plots.

Maine Yankee Shutdown Assessment: A Report To Governor Joseph E. Brennan, Maine State Planning Office

Maine Collection

Maine Yankee Shutdown Assessment: A Report to Governor Joseph E. Brennan

Maine State Planning Office, Maine Office of Energy Resources, Maine Public Advocate

Executive Department - May 1986

Contents: Legal Process / Decommissioning Constraints and Costs / Public and Economic Costs and Benefits / Apprendices

Thickness Design Curves For Asphaltic Concrete On A 4-Inch Layer Of Dense-Graded Aggregate, Or On 6, 9, Or 12 Inches Of Stabilized Soil, Or For Maximum Utilization Of Dense-Graded Aggregate, Herbert F. Southgate

Kentucky Transportation Center Research Report

No abstract provided.

Evaluation Of Durable Lane Delineation Materials, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of the study was to evaluate the cost-effectiveness of available marking materials by means of field tests and to make recommendations concerning the optimum lane delineation materials based on these tests. Materials tested include 100-percent solid epoxy paint, polyester paint, extruded thermoplastic, 3M Stamark tape, 3M Bisymmetric tape, EPOFLEX, solvent epoxy paint, chlorinated rubber traffic paint, and alkyd traffic paint. The test installations have been in place up to four years. The evaluation concerned the durability, reflectivity, and appearance of the materials. Based on current data, expanded use is warranted for 1) polyester paint on lower-volume asphaltic concrete …

Evaluation Of Durable Crosswalk And Stopbar Marking Materials, Kenneth R. Agent, Jerry G. Pigman

Kentucky Transportation Center Research Report

The objective of this study was to find the most cost-effective durable marking material to provide long-lasting stop bars and crossbars. Three materials were tested: 1) 3M Stamark tape, 2) Prismo preformed tape, and 3) extruded thermoplastic (hydrocarbon and alkyd). The various test installations were in place for between 6 and 30 months.

The alkyd-resin thermoplastic material was found to be the most cost-effective I material. The preformed tapes cost two to three times as much as the thermoplastic material while not providing as durable a material when used in this application.The alkyd-resin material maintained its appearance better than the …

Comparison Of Four Infiltration Models In Characterizing Infiltration Through Surface Mine Profiles, Larry G. Wells, A. D. Ward, I. D. Moore, R. E. Phillips

Biosystems and Agricultural Engineering Faculty Publications

A laboratory infiltrometer system was used to evaluate the infiltration process through reconstructed surface mine profiles. Six different profiles were subjected to constant simulated rainfall intensities for selected test conditions. Surface runoff rates were monitored and transient soil moisture contents in the profiles were measured with a gamma density gauge. Unsaturated hydraulic conductivity relationships were determined using Campbelfs method and the "zero-flux" procedure. The infiltration process was modeled by the SCS curve number method, a form of Holtan's equation, the Green-Ampt model and Richards' equation. SCS curve numbers were determined by fitting the method to the observed results. Richards' equation …

Analysis Of Compliant Pins Subjected To Plastic Deformation, Lincoln Miller

Theses

An experimental/numerical analysis of two types of compliant pins is presented: dynamic retention pins and cantilever pins. It is shown that there is a trade-off between the performances of both types of pins. For the same range of retention force, the cantilever pin, with a smaller stiffness, is more forgiving and gives a broader range of deflection. The dynamic retention pin is shown to be more reliable with time and replacement frequency, since it exhibits less plastic deformation for the same range of retention force.