Engineering Commons^™

Tests On Square Reinforced Concrete Members Under Combined Biaxial Bending And Tension, Bhadresh Shah

Theses

The research reported herein studies the ultimate strength behavior for square-shaped reinforced concrete short columns under combined biaxial bending and tension that is a common design problem. The present ACI building code (ACI 318-83) (1) and design hand book (2) do not offer an insight into the determination of strength and ductility behavior of biaxially loaded reinforced concrete columns. A design equation developed by Hsu (3,4,5 ) to study the ultimate strength behavior and failure surfaces for members under these combined action was used and the computed results were compared with the present analytical results and experimental results for square-shaped …

Analyze3d, A Structural Analysis Program Employing Membrane And Solid Finite Elements, James Mendham Gathercole

Theses

The purpose of this thesis is to describe the addition of an 8 and 20-node isoparametric brick element to the finite element program ANALYZE, permitting three-dimensional analysis. The reason for the addition is that even though Analyze is a relatively simple program, its simplicity makes it a good educational tool for finite element courses. The added brick element expands the use of the program for educational purposes.

In its original form, Analyze is a finite element package for static structural analysis developed at Wright Patterson Air Force Base. The program consists of four finite elements: (1) bar, (2) membrane triangle, …

The Effect Of Systemic Arterial Pressure On Microvascular Flow And Transcapillary Exchange Of Macromolecules In The Hamster Cheek Pouc, Govind Mohanlal Gawdi

Theses

Microvascular flow velocities and transport of macromolecules were studied in the hamster cheek pouch under control and acute high arterial pressure conditions, with or without topical (local) application of the vasodilating agent, bradykinin. Mean arterial pressures of 130-160% control were attained by intravenous renin infusion. The microcirculation of the cheek pouch was studied using intravital microscopy. Areas with arterioles and venules were recorded on a videotape for later analysis of red cell velocity, using an RBC tracking correlator, and vessel diameter using a video shearing monitor.

In addition, vascular permeability to macromolecules was studied in the hamster cheek pouch vascular …

Theoretical Investigation Of Submerged Turbulent Jet, Talal N. Hindi

Theses

A theoretical investigation concerning the flow characteristics velocity distribution of a circular submerged turbulent axisymetricic water jet impinging on a flat plate was carried out. Starting with the use of the available data and equations obtained by previous investigators and found room for improvement. By solving these equations for the velocity distribution and comparing them to the experimental results is was found out where improvements of the analysis were were necessary. Then taking Tollwien's solution for the velocity distribution and changing the reference axis to see whether or not the equations would give better results for velocity calculations. With certain …

Zeta Potential Measurements Of Biological Flocs Using A Streaming Potential Cell, Wayne James Gallagher

Theses

A streaming potential apparatus was assembled and tested. Its purpose was to characterize the surface of biological flocs in a wastewater environment. Samples of mixed liquor were obtained from the Passaic Valley Sewerage Commissioners wastewater treatment plant in Newark, New Jersey. Filtered mixed liquor was passed through a bed of the floc particles in the streaming potential cell, and the electric potential across the cell was measured as a function of the differential pressure drop. From these data, the zeta potential was calculated using the Helmholtz equation. Values of -0.88 and -0.44 millivolts were obtained for two mixed liquor samples.

Investigation Of Water-Binding Properties Of Industrial Sludges Using Thermal Analysis As A Monitoring Tool, Ron Josephson

Theses

As part of a program to develop new and more cost-effective dewatering approaches for industrial hazardous wastes, sludges and synthetic "model" materials were analyzed by thermal methods in an attempt to comprehend their water-binding qualities and differentiate free and bound water. These thermal methods included Differential Thermal Analysis (DTA), Thermogravimetric Analysis (TG), and Differential Scanning Calorimetry (DSC). Industrial sludges and laboratory models were compared using both standard heating techniques and subambient cooling (to -60°C). This latter technique provides direct indication of the amount of free water. This information can be very useful in evaluating and improving dewatering techniques for industrial …

The Modeling Of A Self-Oscillating Dc-To-Dc Converter, Frank Andrew Linkowsky

Theses

This thesis develops a model of a nonlinear self oscillating current-or-voltage step-up dc-to-dc converter. Expressions are given that predict the operation of the converter in the time domain and in the state plane. To verify these expressions, a large signal computer simulation technique [1] is used to compare theoretical results with actual measurements. This type of simulation allows a nonlinear switching converter to be modeled with a series of piecewise-linear operating intervals. The resulting waveforms predicted by the developed model show close agreement with waveforms found in the laboratory. Therefore, the model represents a powerful tool that may be used …

Gallium Film Formation By Ion Cluster Beam Deposition, Te-Chuan Hsu

Theses

Gallium thin films were deposited by Ion Cluster Beam (ICB) from pure gallium. This research had two objectives: to develop a practical method of crucible heating to generate gallium clusters; and to investigate the influence of ICB system parameters on the formation of clusters and film properties. An electron-bombardment crucible heater with a novel construction was designed. The top section of the carbon crucible was kept at a higher temperature than the middle section to prevent clogging of the nozzle and " spitting " phenomena which were found to occur with the conventional design. Crucible temperatures up to about 1360°C …

Reliability Of Dielectrics : Using Noise As A Diagnostic Tool, Ramesh K. Jain

Theses

The aim of this thesis is to develop a screening method to predict the reliability of a dielectric material. The screen chosen is an electrical noise. The dielectric material studied is varnished fibre glass cloth material supplied by Westinghouse Electric Corporation.

The dielectric material will have varying amount of voids, crystal defects, and surface contaminants impurities introduced during manufacturing process. On application of the electric stress, ionization (corona) will take place. The corona degrades the material due to thermally generated heat, chemical reactions in the voids and ionic bombardment of the material.

An experimental set up is developed to monitor …

A Tracheoesophageal Puncture Voice Prosthesis, Georghios Makris

Theses

A voice prosthesis was developed that allows verbal communication of laryngectomised patients. The prosthesis requires a superiorly directed tracheoesophageal puncture in which the periscope mounted on the tracheal stoma vent is introduced. The prosthesis is operated by air injection through the periscope. Air injection is achieved by pulmonary pressure after the occlusion of the stoma vent. Stoma vent occlusion can be achieved either by the patient's finger or by the designed cover valve mounted on the prosthesis. The cover valve allows free breathing, hand-free prosthesis use, and it can release excess pressure during coughing. Periscope valve air resistance tests have …

28th Rocky Mountain Conference

Rocky Mountain Conference on Magnetic Resonance

Program and abstracts from the 28th annual meeting of the Rocky Mountain Conference, co-sponsored by the Rocky Mountain Section of the Society for Applied Spectroscopy and the Rocky Mountain Chromatography Discussion Group. Held in Denver, Colorado, August 3-7, 1986.

Acuta Enews August 1986, Vol. 15, No. 8

ACUTA Newsletters

In This Issue

President's Message

UNITS

Party Line

1986/87 ACUTA Board Of Directors

Communications Management: An Evolving Role

Design Of Automotive Structural Components Using High Strength Sheet Steels: Web Crippling Of Cold-Formed Steel Beams, Chiravut Santaputra, Wei-Wen Yu

CCFSS Library (1939 - present)

The structural behavior of high strength cold-formed steel beams subjected primarily to web crippling was investigated analytically and experimentally. In this study hat sections and I-beams, formed from five different types of high strength sheet steels commonly used in the automobile industry, were investigated under various loading conditions. The yield strengths of these sheet steels vary from 58 to 165 ksi. In addition to the test data gathered in this phase of study, the experimental results obtained from the beam tests conducted at Inland Steel Company and Ford Motor Company were carefully evaluated. The evaluation indicated that the present available …

Hydraulic Design Algorithms For Upgrading And Enhancing Water Distribution Systems, Don J. Wood, William T. Gilbert

KWRRI Research Reports

The primary objective of this work was to develop algorithms for directly determining design characteristics for effectively enhancing, modifying or adding to existing water distribution systems. This is accomplished by modifying the basic hydraulic network equations to explicitly determine required design parameters to just meet specified conditions. Initially work was completed on directly determining pipeline diameters and directly determining pipeline and network resistance characteristics. This work was published in technical journals and established the feasibility of the approach but did not demonstrate the scope and versitility of the proposed approach. In this report a general approach is developed and tested …

Evaluation Of I-75 Lane Closures, Jerry G. Pigman, Kenneth R. Agent

Kentucky Transportation Center Research Report

A project on I 75 in Whitley and Laurel Counties during the 1986 construction season involved numerous lane closures associated with spot pavement replacement and joint sealing. Traffic congestion associated with heavy volumes and late merges resulted in the use of the following traffic control devices to supplement standard lane closure devices; 1) variable message signs, 2) supplemental lane closure warning signs, and 3) rumble strips placed in the lane to be closed in advance of the taper.

Results showed a decrease in the percentage of traffic in the lane to be closed with each successive traffic control device in …

Isolation And Characterization Of The Dimers Formed In The Free-Radical And Anionic Initiated Polymerization Of Alpha-Methylstryene, Kevin S. Bosman

Masters Theses

No abstract provided.

Interpretation Of Venous Occlusion Plethysmography Using A Nonlinear Model, F. A. Anderson, Jr., William W. Durgin, H. Brownell Wheeler

Office of the Provost Scholarship

Venous occlusion plethysmography (VOP) is a noninvasive technique widely employed for the detection of deep-vein thrombosis. Previous reports that VOP outflow curves are closely fit by a first-order exponential suggest that venous compliance and resistance are nearly constant. Typically, however, the venous compliance function has a sigmoid shape; in addition, the resistance in a collapsing tube must increase. This paradox was resolved by the surprising finding that for realistic nonlinear compliance and resistance these nonlinearities cancel, producing a quasilinear venous outflow that approximates a simple exponential.

Iowa Academy Of Science Position Paper On Pseudoscience, Iowa Academy Of Science

Position Papers

No abstract provided.

Ole Miss Engineer 1986

Ole Miss Engineer

No abstract provided.

Centre For Computer Aided Management: An Overview, V B Kaujalagi

IIMB Management Review

No abstract provided.

Construction And Performance Analysis Of Frequency Stabilized He-Ne Lasers, Long Hsu

Electrical and Computer Engineering ETDs

The instability and drift in the frequency of an internal mirror He-Ne laser in generally caused by a change in cavity length induced by thermal expansion of the plasma tube. This research developed a simple stabilization technique which is able to stabilize a small He-Ne laser to a fractional frequency stability of 2.3 x 10^-11 for a time period between 0.05 and 0.2 seconds. This stability implies that the laser cavity length does not vary more than 0.06 A°. This improved stability will enable more accurate measurements in optical measurements such as spectroscopy, polarimetry and interferometry.

Production Of Aflatoxin On Damaged Corn Under Controlled Environmental Conditions, D. M. Wieman, G. M. White, Joseph L. Taraba, I. J. Ross, Clair L. Hicks, Bruce E. Langlois

Biosystems and Agricultural Engineering Faculty Publications

Aflatoxin B₁ production by Aspergillus flavus (NRRL 6432) was determined on physically damaged corn stored at 35,25 and 20°C and at relative humidities of 97 and 92%. Production at lower relative humidities of 80 and 85% were also tested at 25°C. Production lag times were significantly different for all test conditions. Lag times ranged from 46 h at 97% relative humidity and 35°C to 173. 8 h at 20°C and 92% relative humidity. Aflatoxin B, concentration doubled every 6 to 10 hours after a level of 10 ppb had been reached. Production rate constants were not significantly different between …

Acuta Enews July 1986, Vol. 15, No. 7

ACUTA Newsletters

In This Issue

Fall Seminar --- Orlando, Florida

Party Line

When Growth & Technology Spur Phone-system Change

Dial M For Madness

Bulletin - July, 1986, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A six page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Traffic Forecasting For Pavement Design, Harshad R. Desai, Rick Reel, Robert C. Deen, Herbert F. Southgate, Ronald Noble, Vernon L. Tabery, Mark Hallenbeck, Dennis Crimmins, Wiley Cunagin

Kentucky Transportation Center Research Report

The need for improved traffic estimation procedures has been emphasized by several studies that demonstrated that previously available data were not adequate. Some data were not considered representative of actual traffic conditions because of overloaded trucks avoiding weighing scales and insufficient traffic sampling programs. In addition, previous forecasting procedures did not reflect the increases in legal load limits, the significant increase in the number of heavy trucks, or the shift toward larger vehicle types that has occurred in recent years.

Improved estimates of current traffic loadings based on larger samples of much higher quality data would allow development of procedures …

Performance Monitoring Of A Highway Tieback Wall (I 71, Carroll County, Ky 227, Corrective Landslide Measure), Bobby W. Meade, David L. Allen, Tommy C. Hopkins

Kentucky Transportation Center Research Report

A tieback wall was used to control an earth slide on KY 227 in Carroll County. Herein is contained a description of the wall construction and problems encountered during construction. Also included are descriptions of materials used and wall components.

The short-term wall performance indicates the tieback wall has controlled the earth slide and, to date, is a satisfactory solution. Long-term monitoring of the tieback wall will continue.

A Compiler For A Two-Dimensional Programming Language, Julie Wing Kam Choi

All Computer Science and Engineering Research

A visual programming language is presented. This language uses interactive graphics to convey notion such as subroutine, recursion, block structure, parallel and serial processing to school children. Currently the system is interpreter based. To overcome the inefficiency of the interpreter based system, a compiler is implemented for this language. This report gives an overview of the compiler and the details about the parser, semantic analyzer and the code generator. Finally, a performance comparison between the interpreter based system and the compiler based system is given.

Economic Analyses Of Millings, Herbert F. Southgate

Kentucky Transportation Center Research Report

Economic analyses were made using 1984 and 1985 contract bid data. Data were identified as to who retained ownership. Recommendations as to who retains ownership are made based upon factors prevalent for a specific candidate pavement and other circumstances.

The Effect Of Grinding On The Sorption Capacity Of Activated Carbon, John Garrett Dempsey

Civil & Environmental Engineering Theses & Dissertations

The current procedure employed to design full scale activated carbon contacting systems is presented in detail and followed by a review of the more important process controls and operating parameters. Inherent limitations of the design procedure are identified, with the need to be able to accurately predict carbon sorption capacity from bench scale analysis determined to be the most important. Some of the more recent models developed to predict activated carbon sorption capacity were analyzed leading to the realization that even the most sophisticated dynamic models were based upon sorption capacities determined from classical isotherm procedures. The validity of the …

An Analytical And Experimental Study Of Clearance And Bearing-Bypass Load Effects In Composite Bolted Joints, Rajiv Vikas Arun Naik

Mechanical & Aerospace Engineering Theses & Dissertations

A combined analytical and experimental study is conducted to determine the effects of clearance and bearing-bypass loading for mechanically fastened joints in composites. A simple method of analysis is developed to account for the nonlinear effects of bolt-hole clearance. The nonlinear load-contact variations for clearance-fit fasteners are also measured using specially instrumented fasteners. For a quasi-isotropic graphite/epoxy laminate, results show that the contact arc as well as the peak stresses around the hole and their locations are strongly influenced by the clearance. After a slight initial nonlinearity, the peak stresses vary linearly with applied load. The typical clearance levels are …