Engineering Commons^™

An Investigation Of Electrical And Physical Properties Of Reactively, Diode Sputtered Silicon Nitride Thin Films, Divyang Manharlal Shah

Theses

Silicon nitride thin films were deposited by r.f. reactive sputtering of silicon in nitrogen and argon discharge. Biased and unbiased modes of diode mode sputtering were used. Typical parameters for a sputter deposition run were: base pressure, 1-2x10-6 torr; sputtering pressure, 5-7 mtorr; nitrogen partial pressure, 15-16%; cathode-anode gap, 4 inch; r.f. power, 200-250 watts; cathode voltage, 1.8-2.1 V r.f.; water vapor pressure, 20-30% of the base pressure. The film thickness and the refractive index were measured by ellipsometery. The films of thickness 300-2500A, refractive index 1.9-2.1 and resistivity 10101Ω — cm were obtained. The deposition rate was in the …

Design Of An Experimental Apparatus To Measure The Charge And Mass Of Ionized Species In A Partially Ionized Cluster Beam Deposition System, Nitin K. Shah

Theses

The objective of this research was the design and construction of an experimental apparatus to investigate the size distribution of gallium clusters that can be emitted from a heated crucible with a 1 mm nozzle. This research work involved the design and construction of a partially ionized cluster beam (PICB) deposition system which would provide low charged particle background for retarding field analysis and cluster size measurements. The apparatus also allowed control of critical parameters on which the cluster size may depend.

The promise of PICB is based on the formation of clusters of adatoms, their ionization and their acceleration …

Seizure And Wear Testing Methodology, I-Tsung Shih

Theses

In this work the seizure as an adhesive wear has been discussed and analyzed The diffusion hypotheses is accepted as the seizure mechanism. It was determined that the surface of machine components, material properties, and contact stresses in sliding and loading zone are responsible for the wear.

A computer controlled wear testing methodology has been developed and a wear testing machine has been designed and assembled. The tests for the selected gray cast non and alloy steel specimens with different surface treatment were performed on the designed wear testing machine.

The test results showed that the selected materials with additional …

Investigation Of High Shear-Rate Viscoelastic Flow, Sudarshan S. Sood

Theses

The object of this study is to understand two important characteristics exhibited by viscoelastic fluids at high shear-rates, and analyse their influence on practical applications Viscoelastic fluids, such as polymer solutions, when subjected to high shear stress, behave in a manner which has not been sufficiently analytically explained In experimental studies, such fluids have shown.

(a) Stress relaxation.

(b) Decrease of viscosity with an increase in shear rate.

(c) Slight decrease of viscosity with temperature.

(d) Normal stress differences in shear flow.

In this thesis an analytical explanation is given for two (a and b ) of these features This …

Friedman's Model Of Calculating The Optimum Bid Price Using Dbase Iii Plus, Selim Uzel

Theses

The micro-computer program, BIDCALC presented in this thesis is offered as simple, practical, and proven approach to developing an effective data-based competitive bidding strategy. BIDCALC is written in dBASE III Plus programming language for MS-DOS based computers.

Main purpose of the program is to evaluate the optimum bid using the Friedman's model of Maximizing the Expected Profit. At the same time the program keeps track of necessary competitor and project information in data base files which are easily transferable to other software packages. The program is capable of generating a variety of reports in a matter of seconds.

BIDCALC is …

Investigation Of The Characteristics Of The Kerf And The Surface Generated In The Course Of Cutting Titanium With Abrasive Waterjets, Ajay Vora

Theses

The effect of cutting parameters on the quality of cut in the course of cutting Titanium (Gr.2) with Abrasive Waterjet is investigated. The cutting parameters include nozzle traverse rate, size and feed rate of abrasives and nozzle(s) diameter. The width of kerf (top and bottom ), taper and roughness is studied. The measurements are tabulated and plots are made to study the trend and relationship for each set of parameters.

The qualitative conclusions are made successfully but no quantitative relationship was derived. Suggestions are made for the evaluation of technology for feasibility and economic justification, and to achieve desired cutting …

Attenuation Properties Of An Lp 11 Mode In A W-Type Fiber Operating Below Cutoff, Chih-Chiang Wang

Theses

Rigorous formulation of a W-type fiber for its dispersion properties is presented. An LP mode has been studies extensively with respect to its attenuation properties when the frequency of operation is kept below cut-off. Due to rigorous dispersion equation numerical difficulties encountered in the computations, an approximate dispersion equation corresponding to weakly guided modes is solved. Numerical results corresponding to attenuation and propagation characteristics of the W-type fiber for radii and refractive index variations are presented. A computational subroutine for radial functions (Bessel, etc ) for complex argument has been used and proved to be useful in the legion of …

Schema Based Wiring Tool : A Computer Network And Cad Design System, Jia Jing Zhang

Theses

For the purpose of building a SBC-8052-Basic micro-controller based instrument system, a new SCHEMA II Computer Aided Design system for IBM-PC is used to enhance circuits design routine, and it is described here. The new features of this CAD are discussed, and the design example of a new version of the SBC-8052-Basic micro-controller is given here in detail.

Since the wiring board system is adopted as tool of the laboratory development and controlled by the QL microcomputer, and since SCHEMA II CAD, on the other hand, is used on the IBM-PC-AT, communication between the two microcomputers is accomplished, and the …

On-Line Blood Glucose Control System, Huan Zheng

Theses

A method has been developed that can monitor and control the meal initiation of rats. The goal of studying meal initiation is to find a mechanism of control of the diet, based upon the assumption that the body weight is closely related to feeding behavior. If the feeding behavior can be controlled, then the body weight can be controlled. The experimental system has two major functions: (1) Continuous measurement and recording of the blood glucose concentration and meal pattern of rats. (2) Automatic or manual infusing of glucose or other substances to the rats intravenously.

For blood glucose concentration and …

C/Ku Band Satellite Television Reception System, Costas A. Economides

Theses

The purpose of this thesis is to examine and investigate the design of a satellite reception system able to receive most C and Ku band North American geostationary satellites' TV transmissions. The performance criterion used for the system design is based on a required demodulated video signal-to-noise ratio maintained for a specified percentage of time in conjunction with overall cost considerations.

Furthermore, a computer program written in FORTRAN 77 is developed, which among other functions lists the notified, operational, geostationary satellites in sight with their corresponding look angles, from any given location on the earth.

Determination Of Polycyclic Aromatic Hydrocarbons From Incineration Emission Samples, Robert Cebula

Theses

Stack emissions from five sources (one pulverized coal combustion operation, three sewage sludge incineration operations and one gray tin refractory operation) were sampled by use of U.S. EPA Modified Method 5 isokinetic sampling unit for vapor and particulate effluent. The sampling unit provided XAD-2 resin samples, polytetrafluoroethylene and glass fiber filters and impinger washings of dichloromethane. The resins were soxhlet extracted using dichloromethane (DCM) and the filters were soxhlet extracted using DCM followed by acetone. Fractionation of extracts was accomplished by thin layer chromatography. The resulting fractions were analyzed for polycyclic aromatic hydrocarbons (PAH), nitro-PAH and quinone-PAH by high-performance liquid …

A Model For The Determination Of Market Based Pricing Of Telecommunication Products, Katherine J. Sullivan

Theses

The deregulation of AT&T, has impacted telecommunication product pricing in the U.S. market. Previously, pricing had been based on cost plus mark-up, as stipulated by regulatory commissions. Now, pricing decisions require consideration of the competitive impact, consumer demand for the product, corporate pricing objectives and marketing strategies. This paper proposes a pricing process that is relevant for this new environment which enables the product manager to price properly.

The method proposed utilizes microeconomic theory and takes into account the product test price, unit cost, opportunity cost, nonprice factor cost and consumer demand. Incorporating a number of different pricing strategies, it …

Comparison Of Various Techniques For The Detection Of Lines In 2-Dimensional Images, Somayajulu Bhamidipati

Theses

The detection of straight lines in 2-dimensional images leading to polygonal approximation to the boundaries of the objects is one of the important stages in scene analysis as it leads to the description of the images. The comparison of three diverse approaches for this problem in terms of the efficiency and accuracy is made, and their performance for different types of data and different sets of parameters is studied in this thesis.

The data points are generated using either an edge detection algorithm using chain encoding on real images or a synthetic data generator, which can create a variety of …

Ibm/Xt-Based Automatic Monitoring Instrumentation System For Eating Behavior Studies In Rats, Binghong Gui

Theses

An auto-feeding system based on the IBM-XT microcomputer has been designed for use in the anti-obesity research program in the Pharmacology Department at Hoffmann-La Roche Inc. By using this system, experimental rats can be automatically fed, some which have been given anti-obesity drugs and some which have not. The system can also collect data, such as eating times and food intake, which are used for studying the rat's eating behavior.

The system is designed to control thirty six cages with one experimental rat in each cage and it performs three functions:

1 ) To automatically dispense a preset quantity of …

The Application Of Zero-Sum Games To Low Sensitivity Optimal Control, Jun Huang

Theses

This thesis deals with the synthesis of low sensitivity optimal control systems. Zero-Sum games are applied to the first order linear differential equation system. The goal is to obtain an optimal control of the system performance, and at the same time, reduce the sensitivity of the performance index and sensitivity trajectory.

In this thesis, the quadratic index of performance is selected in the argumented system which is combined/ the system equation with the sensitivity equation. Two control variables U & V are selected to maximize and minimize the system, in order to obtain the optimal value of the system.

Two …

A Dynamic Set-Based Multiaccess Protocol For Local Area Networks, Parul S. Nanavati

Theses

The packet-broadcasting technique brings together the advantages of both packet switching and broadcast communication. The central problem of a packet broadcast network is conflict resolution among the users sharing the broadcast communication link. Collisions are the major source of transmission errors which degrade the performance of a LAN. Proposed here is a novel multiaccess protocol which offers full communication resources to the user at low traffic requirements. It dynamically adjusts the number of users allowed to access the medium at heavy traffic requirements such that number of collisions are reduced and thus maintains the efficient utilization of the medium and …

Reliability Problems In Semiconductor Lasers, Ajay R. Patel

Theses

The stability and reliability of semiconductor laser is dependent on its design, fabrication, and output power. The best way to assure high reliability of these devices is by accelerated aging test and by selection of strict and meaningful criteria for the acceptance or rejection of a particular device. In this thesis emphasis is given on different failure mechanisms that are known. As new development takes place, other mechanisms may be found. Catastrophic degradation, gradual degradation, darkline defects, and contamination during the fabrication process are the main source of device failure.

The noise generation and the packaging issue of semiconductor laser …

Microprocessor Testing And Computer Aided Diagnosability Of Digital Circuits, Shirish Patel

Theses

Computer Aided Diagnosability Of Circuits (CADOC), a new method is developed for isolating and pin-pointing a faulty device in digital circuits. CADOC is based on graph-theoretic principle and PFD numbers. Without considering any SA1 or SAO faults, we can zoom out faulty device by selecting different diagnostic path to narrow down the faulty region and to isolate the faulty device. The efficiency of this new technique is confirmed by applying the technique to many examples.

Reliability Evaluation Of Liquid Crystal Displays Under Accelerated Test Conditions, Ishatdev Singh Rathore

Theses

This thesis deals with the recent study of reliability of liquid crystal displays. This study determined the effects of high temperature on LCD reliability. To accomplish this, reliability life testing was done on different kinds of LCD samples under different operating conditions. The tests were carried out on the samples of two different vendors at two different temperatures. No humidity was added in any test.

Vendor No. 1

1. 120 units at 77° ± l° C.

2. 80 units at 85° ± 1° C.

Vendor No. 2

1. 60 hard and 60 soft glass units at 77° ± 1°C.

2. …

Sorption Characteristics And Their Effects On Geotechnical Properties Of Clay Soils, Arambawattage Mahendra Rodrigo

Theses

An experimental investigation on the sorption characteristics of clay soils with liquid organics (phenol, chlorophenol, nitrophenol and chlorobenzene) and their effects upon geotechnical properties was undertaken. The investigation consisted of two different phases, namely, (1) the sorption/ desorption study, including kinetic rate, equilibrium time, isotherm modeling, and (2) geotechnical properties due to clay/ liquid organic interactions. The results of kinetic rate study indicate that the equilibration time for the contaminants way dependent upon the hydrophobic or the hydrophelic nature of the chemical. For equilibrium adsorption models, the linear isotherm was found to be the best fit in predicting sorption capacities …

Analysis Of Spread Spectrum System Using Direct Sequence Technique In Jamming Environment, Kandarp A. Vyas

Theses

A spread spectrum system is a means of transmitting data over a channel In addition it offers a wide variety of features like data security and signal hiding This work studies in detail a spread spectrum system using direct sequence binary phase shift keying. The Sliding Correlator and Sequential Detector techniques have been used to achieve synchronization. A brief study of pseudorandom noise has been presented. System was simulated on UNIX using 'c'. A modified version, suitable for software implementation, of Sliding Correlator and Sequential Detector was, used. Results generated using tins model are presented here.

The State And Future Of Televised Professional Training Systems, Robert Michael Brady

Theses

This paper investigates the topic of televised professional training -- that is training and educating managers and technical professionals via live or videotaped television broadcasts. The investigation begins with a description of how some typical educational networks operate; it then goes on to analyze in a strictly theoretical sense, some of the advantages and disadvantages that such a system would have compared with the traditional methods of offering continuing education; it then discusses the results of two specially prepared surveys -- one addressed to the administrator/manager, and one addressed to the student. These areas are then united in a final …

A Dynamic Model Of A Fill-And-Draw Reactor And Its Implications For Hazardous Waste Treatment, Shing-Hwa Chang

Theses

A dynamic model of a fill-and-draw reactor has been developed, which includes a number of operational parameters such as the draw-down volume, the fraction of total cycle time devoted to fill, reaction, and draw, and the concentration of the toxic substance in the feed to the reactor. The model has been solved numerically for two cases, one assuming Monod kinetics, and one considering substrate inhibition (Andrews kinetics).

The conversions achieved with this type of reactor have been compared to that of a conventional activated sludge (CSTR) design. These results indicate that for most practical settings of the operating parameters, the …

Temperature Dependent Reliability Of Plastic Packaged Microcircuits, Wasim Ahmed

Theses

Increasing power and power densities in new high complexity semiconductor devices are creating heat removal problems. Increased powers produce higher junction temperature which lead to potentially faster degradation of device reliability. Thermal management at device level packaging involves efficient and cost-effective removal of dissipated thermal energy from the device to assure its reliable performance over the long term. In the context of very high levels of integeration of future ICs, thermal management will mean making such devices possible close to the limits of acceptable high temperature.

The major factors affecting heat flow in a plastic Dual-in-line-packages (DIP'S) are investigated using …

An Investigation Of Interrupt Handling Schemes In Pipeline Processors, Shailesh Ratilal Gami

Theses

In order to acheive higher performance in a pipeline processor, proper interrupt handling is essential. In a pipeline processor, interrupt handling is difficult because many instructions are in the processor at the same time. This study describes and evaluates the different solutions to interrupt handling. Several pipelined 32-bit microprocessors have also been studied and their architectural and programming features are compared.

Performance Of Single Dwell Serial Synchronization System, Chan-Yee Hsiung

Theses

By using the sampling theorem, the problem of the detection of a signal in white Gaussian noise, reduces to the consideration of the sum of the squares of statistically independent Gaussian variates. If the transmitter and and receiver are not synchronous, then no data transmission is possible and the decision statistic has a central chi-square distribution. Otherwise, the decision statistic has a non-central chi-square distribution. Also, this. paper presents a method to calculate the mean and variance of the acquisition time which are the most important parameters to evaluate the performance of a PN spread synchronization system. In addition, the …

Development Of 8052ah-Basic Based Single Board Computer Ii, Suping Lou

Theses

8052AH-BAISC Based Single Board Computer II ( SBC II ) is designed and developed for the application in biomedical instruments as an embedded central processing unit. SBC II offers powerful function in digital signal acquisition, storage and processing, smart on-board EPROM programming, various preipheries supporting and custom supervisor program. The techniques of design and development of SBC II includes computer aided circuits analysis and schematic, optimal design algorithms and computerized setting up SBC II prototype.

This thesis combines the analysis of SBC II circuitry, set up and operation of the complete computer aided electrical circuit design software OrCAD/SDT specifics in …

3-D Reconstruction Of Microvasculature From High Voltage Electron Microscopy (Hvem) Data, Pradip Kumar Paul

Theses

This is a new method for histoarchitectural and volumetric analyses of cell compartments of microvasculature with the use of a unique combination of computerized 3-D reconstruction and HVEM thick serial cross sections. The technology is potentially a reliable, simple, accurate and fast method. Pioneering work in this area was started by Todd et al. (Circ Res Vol :53 p 319 ;1983) basically using light microscopy, but supported by conventional ultrathin transmission electron microscopy. These techniques are important in that they promise to resolve controversies in terms of evaluating the occurance of hyperplasia and hypertrophy in small resistance vessels in various …

Biosynthesis Of Amine Oxides Using Calcium-Alginate Immobilized Hog Liver Microsomes : An Evaluation Of Process And Reactor Design, Ioannis I. Valvis

Theses

An evaluation of the biocatalytic ability and the potential utilization of Calcium-alginate immobilized hepatic microsomes (beads) for the biosynthesis of amine oxides has been performed, To accomplish this task, the following three areas Were investigated: immobilization, catalytic biooxidation ability, and reactor configurations.

Immobilization was found to result in higher yields over free microsomes at the expense of higher cofactor requirements. Refrigerated drying of immobilized micro-somes appears to be a better storage technique than wet storage in buffer. Smaller beads resulted in higher rates than larger beads, but size did not affect the overall yield.

Chlorpromazine (CPZ), diphenylamine (DPA) and 4-hydroxy-2,2,6,6-tetramethylpiperidine …

Study Of The Structure And Capacity Of Construction Industry In Pakistan, Tayyab A. Ansari

Theses

The construction industry is the second largest sector in Pakistan's economy after agriculture. It is a fragmented industry which includes very small and very large contracting groups. It includes professional groups such as architects, engineers, management personnel etc. Major part of this industry is dominated by material's suppliers, vendors etc.

In the light of the developments which have taken place particularly over the last ten years, the study has covered the capacity of the construction industry in terms of estimated output, availability of manpower, demand and production of building materials , financial problems, credit, quality of work, the role of …