Engineering Commons^™

Simplified Strength Prediction For Cold-Formed C- And Z-Shapes, Roger A. Laboube

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Although cold-formed steel C- and Z-shaped members possess a very favorable strength-to-weight ratio, are easily fabricated and erected, and offer a cost-effective structural design solution, they can be highly susceptible to local buckling. To adequately address the impact of the local buckling limit state, a complex, time-consuming design office effort may be required. Therefore, to facilitate the design of such shapes, a study was conducted that focused on developing relatively simple, easy-to-apply design guidelines. The design guidelines address the behavior of cold-formed steel C- and Z-shaped members when used as either a flexural member or a compression member. Both edge-stiffened …

Collapse Behavior Of Pino Suarez Building During 1985 Mexico City Earthquake, Jeng Fuh Ger, Franklin Y. Cheng, Le Wu Lu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the investigation of the collapse behavior of a 22-story steel building during the September 19, 1985, Mexico City earthquake by studying hysteretic behavior, ductility factors of individual structural components, and overall instability of the building. Extensive inelastic analyses have been performed for the building by using the multicomponent seismic input of actual Mexico City earthquake records. It was found that the structural response exceeds the original design ductility of this building, and most girders in the building have severe inelastic deformation. Due to the load redistribution that results from ductile girder failure, local buckling occurred in many …

Postbuckling And Hysteresis Models Of Open-Web Girders, Jeng Fuh Ger, Franklin Y. Cheng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The paper presents analytical studies of hysteretic behavior of open-web girders with angle web members. The partial inelasticity of the member cross section is traced using finite segment formulation with stress-strain control. A member is divided into a number of segments, and, for each segment, the cross section is divided into many small elements, which allows the inelastic deformation of the member to be modeled. Therefore, member stiffness is established for various inelastic deformation stages. The eccentricities and initial imperfections of web members are considered in the analysis. Good agreement between experimental and present analytical results was found for individual …

Postbreakage Behavior Of Heat Strengthened Laminated Glass Under Wind Effects, Chris P. Pantelides, Amy D. Horst, Joseph E. Minor

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Results of a full-scale experimental investigation into the post breakage behavior of heat-strengthened laminated glass subjected to windstorm effects are presented. Two different interlayer constructions and two different glazing configurations are examined. The two interlayer constructions are a PVB polymer and a PVB/PET/PBV composite polymer. The two glazing configurations are a conventional dry glazed system and an unconventional system with a silicone anchor bead. Two test criteria are established that relate to effects of a severe windstorm. The first criterion addresses impact with windborne debris; the second defines a wind-load spectrum that represents a severe windstorm of a 4-hr duration. …

Robust Control Of Flexible Structures Using Multiple Shape Memory Alloy Actuators, R. Lashlee, R. Butler, Vittal S. Rao, F. Kern

Electrical and Computer Engineering Faculty Research & Creative Works

The design and implementation of control strategies for large, flexible smart structures presents challenging problems. To demonstrate the capabilities of shape-memory-alloy actuators, we have designed and fabricated a three-mass test article with multiple shape-memory-alloy (NiTiNOL) actuators. The force and moment actuators were implemented on the structure to examine the effects of control structure interaction and to increase actuation force. These SMA actuators exhibit nonlinear effects due to dead band and saturation. The first step in the modeling process was the experimental determination of the transfer function matrix derived from frequency response data. A minimal state space representation was determined based …

Battery Energy Storage Technologies, Max Darwin Anderson, Dodd S. Carr

Electrical and Computer Engineering Faculty Research & Creative Works

Battery energy storage systems, comprising lead-acid batteries, power conversion systems, and control systems, are in commercial operation around the world. They are used by three main groups: power generating utilities; power distributing utilities; and major power consumers (such as electric furnace foundries). The principal advantages of battery energy storage systems to generating utilities include load leveling; frequency control; spinning reserve; modular construction; convenient siting; no emissions; and investment deferral for new generation and transmission equipment. Power distributing utilities and major power consumers can avoid costly demand changes by discharging their batteries at peak periods and then recharging with lower cost …

Long-Term Performance Of Flexible Pavements Located On Cement-Treated Soils, Tommy C. Hopkins, David Q. Hunsucker, Tony L. Beckham

Kentucky Transportation Center Research Report

Long-term performance of flexible pavements located on cement-treated soils and the longevity of soil-cement subgrades are examined at sections of four highway routes. Ages of the soil-cement subgrades range from 6 to 30 years. Field and laboratory studies were conducted at each section. Generally. the soil-cement subgrades were non-plastic and were classified as SM, or sandy silt, according to the Unified Soil Classification System, although the classification of the untreated soil subgrades located below the treated layers ranged from CL (clay) to GC (clayey gravel). Plasticity index of the untreated soils ranged from non-plastic to 44 percent. Generally, the untreated …

Kentucky Traffic Accident Facts 1993 Report, Kentucky State Police

Kentucky Transportation Center Research Report

KENTUCKY'S TRAFFIC ACCIDENT FACTS report for 1993 is based on accident reports submitted to the Accident Unit housed in the Kentucky State Police Information Services Branch, Records Section. As required by Kentucky Revised Statutes 189.635, "every law enforcement agency whose officers investigate a vehicle accident of which a report must be made ... shall file a report of the accident ... within ten days after investigation of the accident upon forms supplied by the bureau." The stated purpose of this requirement is to utilize data on traffic accidents" for such purposes as will improve the traffic safety program in the …

An Optoelectronic Implementation Of The Adaptive Resonance Neural Network, Donald C. Wunsch, T. P. Caudell, R. J. Marks, R. A. Falk, C. David Capps

Electrical and Computer Engineering Faculty Research & Creative Works

A solution to the problem of implementation of the adaptive resonance theory (ART) of neural networks that uses an optical correlator which allows the large body of correlator research to be leveraged in the implementation of ART is presented. The implementation takes advantage of the fact that one ART-based architecture, known as ART1, can be broken into several parts, some of which are better to implement in parallel. The control structure of ART, often regarded as its most complex part, is actually not very time consuming and can be done in electronics. The bottom-up and top-down gated pathways, however, are …

Permeation Of Several Gases Through Elastomers, With Emphasis On The Deuterium/Hydrogen Pair, M. (Mark) W. Fitch, W. J. Koros, R. L. Nolen, J. R. Carnes

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Diffusion and Permeation Coefficients for He, H2, D2, O2, and N2 in a Variety of Elastomers Were Measured by Simple Manometric Methods. the Elastomers Studied Were Butyl Rubber; Hypalon® 40 and 45; Viton® E60 and GF; Hydrin® 100 and Filled Hydrin® 100; Kraton® G, FG, and KG VTEOS; EPDM; Epoxidized Natural Rubber; and Neoprene. Consistent with Earlier Studies, Elastomers with Higher Glass Transition Temperatures Exhibited Lower Diffusion Coefficients. the Ratio of Diffusion Coefficients of the Hydrogen Isotope Pair Differed from the Purely Molecular‐weight‐based Prediction. Deuterium's Slightly Smaller Size Relative to Hydrogen is Consistent with Observed Deviations from the Molecular‐weight‐based …

Evaluation Of Clsm (Flowable Fill) For Trench Backfill, Bobby W. Meade, David Q. Hunsucker, Michael D. Stone

Kentucky Transportation Center Research Report

Controlled Low Strength Material (CLSM), commonly referred to as flowable fill, has been used for years as a trench backfill for utility repairs in Kentucky, but had not been previously used by the Kentucky Department of Highways (KDQH). In 1991, the KDOH awarded a contract for the reconstruction of Breckinridge Lane in Louisville where CLSM was used as trench backfill for all storm drainage. In 1992, the KDOH awarded a contract for replacement of cross drains for US 25 in Fayette County where CLSM was used as trench backfill. These two sites were monitored for field performance, cylinders were cast …

Development Of Guidelines And Performance For Asphalt Pavements Containing Rubber -- Review Of State-Of-The-Practice, Kamyar C. Mahboub, Donn E. Hancher

Kentucky Transportation Center Research Report

This interim report provides a summary of key points that are important to successful implementation of the asphalt rubber technology in Kentucky in accordance with ISTEA. Various asphalt rubber technologies are presented in this report along with their advantages and disadvantages. Issues related to structural design and construction are discussed. A variety of environmental issues such as: emissions, leachate and issues related to future recyclability are presented. Finally, criteria are recommended to be used for selection of future asphalt rubber projects in Kentucky.

The Removal Of Lead-Based Paint From Steel Bridges, Theodore Hopwood Ii, Christopher M. Oberst

Kentucky Transportation Center Research Report

The purpose of this study was to assist the Department of Highways in conducting bridge-painting operations involving removal of existing lead-based paint. Pertinent state and Federal regulations affecting generation of hazardous wastes, limiting environmental pollution and protecting public and worker safety were obtained and reviewed.State highway agendas were surveyed relative to how they conducted maintenance bridge painting involving lead-based. paints and comply with applicable regulations. Information from the painting industry related to sale removal of lead-based paints was also reviewed.

Based upon the reviews of applicable regulations, operations of other state highway agencies and painting industry practices, the best demonstrated …

Reliability Trend Analyses With Statistical Confidence Limits Using The Luke Reliability Trend Chart, Stephen R. Luke

Engineering Management & Systems Engineering Theses & Dissertations

In electronic systems, it is interesting to understand exactly how the reliability is changing with time. Dynamic performance changes when a system passes from infant mortality stage into useful life phase and when the system passes from useful life phase into wearout phase. Dynamic performance also changes when the system is redesigned or when the system is acted on by a number of other outside forces such as a change in maintenance policy, escalation of alignment problems, or a change in training program. It is important to know when a system is changing dynamically in order to assess design, policy …

The Use Of A Factory Simulation To Evaluate A Flexible Control Structure For Integrated Manufacturing, Ling Ling Pan

Engineering Management & Systems Engineering Theses & Dissertations

Once a control structure for an integrated manufacturing system is decided upon, manufacturing activities are limited by that structure. A flexible control structure is presented as an approach for accommodating a variety of manufacturing activities, without being limited to a single control structure. A flexible control structure is one that allows multiple types of control structure in the manufacturing process. For example, both hierarchical and non-hierarchical structures may be used in a flexible structure. The properties of a flexible control structure are discussed from the point of view of graph theory.

Control structures for automated manufacturing are difficult to evaluate …

Phenotypic Characterization Of Copper-Resistant Mutants Of Methylosinus Trichosporium Ob3b, M. (Mark) W. Fitch, D. W. Graham, R. G. Arnold, S. K. Agarwal, P. Phelps, G. E. Speitel, G. Georgiou

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Cultures of Methylosinus Trichosporium OB3b Grown in the Presence of Very Low Concentrations of Copper Synthesize a Soluble Methane Monooxygenase (SMMO) that Efficiently Catalyzes the Oxidation of Trichloroethylene and Other Organic Pollutants. Recently, We Isolated Five M. Trichosporium OB3b Mutants that Express SMMO Activity When Grown in the Presence of Elevated Copper Concentrations (P. A. Phelps, S. K. Agarwal, G. E. Speitel, Jr., and G. Georgiou, Appl. Environ. Microbiol. 58:3701-3708, 1992). Here We Show that, in Contrast to the Results for the Wild-Type Cells, the Addition of Copper to Mutant Cultures Grown on Methane and Nitrate as the Nitrogen Source …

Mineralization And Uptake Of Triazine Pesticide In Soil-Plant Systems, Dhileepan R. Nair, Joel G. (Gerard) Burken, Louis A. Licht, Jerald L. Schnoor

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Deep-Rooted Trees Planted as a Buffer Zone Can Intercept Runoff and Eroded Sediments, Thus Reducing Non-Point-Source Pollution Due to Agricultural Chemicals. in This Study, Populus Sp. Were Grown in Bioreactors with an Agricultural Soil (Silt-Loam) and in a Silica-Sand Media; Both Were Spiked with ¹⁴C Uniformly Ring-Labeled Atrazine. the Plants Took Up over 11% of the ¹⁴C Labeled Atrazine Applied to the Silt-Loam Soil and over 91% of that Applied to the Silica Sand Media, with the Majority of the ¹⁴C Accumulating as Nonphytotoxic Metabolites in the Leaves. Research Suggests that, in Addition to Nutrient Uptake, Poplar …

An Analytical Investigation Of Aashto Load Equivalencies, Herbert F. Southgate

Kentucky Transportation Center Research Report

An objective of this study was to develop procedures and/or refined relationships between Kentucky ESALs and AASHTO ESALs. Kentucky load equivalency relationships are the result of mechanistic analyses based on elastic theory. AASHTO load equivalency relationships were developed from recorded empirical data collected at the AASHO Road Test. Comparison of Kentucky and AASHTO ESALs necessarily in depth analyses of AASHTO load equivalency equations C-19, D-19, and their developmental equations given in the 1972 AASHTO Interm Guide. These equations evolved from the basic format used in analyzing AASHO Road Test data.

In this investigation, the repetitions reported in Appendix A of …

Analog Chips And Intelligent Vehicles, J. G. Harris

Electrical and Computer Engineering Faculty Research & Creative Works

Numerous digital-based sensor systems have been demonstrated on intelligent vehicles but only the most rudimentary experiments have been attempted with analog VLSI chips in real-world environments. The most significant factor in the choice between analog and digital approaches to sensory processing in intelligent vehicles will be the cost of mass production. If analog sensors can be designed with enough speed, resolution and accuracy to solve sensory processing tasks, then the low-cost of mass production ensures that analog circuits will be the technology of choice for future generations of smart sensors. Current analog VLSI sensors do not have enough resolution and …

Structural Behavior Of Architectural Laminated Glass, R. A. Belir, Joseph E. Minor, H. S. Norville

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Experimental and theoretical investigations conducted over a 20-year time period by several investigators provide sufficient data and information to define, for practical engineering purposes, the behavior of architectural laminated glass under lateral pressures. Investigations included definitions of material properties, theoretical stress analyses, experimental stress analyses, and destructive tests involving monolithic, laminated, and "layered" glass plates of several geometries. The preponderance of data and information indicate that: (1) Architectural laminated glass behaves in a manner similar to monolithic glass of the same nominal thickness under short-term lateral pressures (representative of wind loads) at and below room temperature; (2) the temperature at …

Lattice Boltzmann Thermohydrodynamics, F. J. Alexander, S. Chen, J. D. Sterling

Business and Information Technology Faculty Research & Creative Works

We introduce a lattice Boltzmann computational scheme capable of modeling thermohydrodynamic flows of monatomic gases. The parallel nature of this approach provides a numerically efficient alternative to traditional methods of computational fluid dynamics. The scheme uses a small number of discrete velocity states and a linear, single-time relaxation collision operator. Numerical simulations in two dimensions agree well with exact solutions for adiabatic sound propagation and Couette flow with heat transfer. © 1993 The American Physical Society.

A Model Of Electronic Warfare Systems Acquisition And Engineering For Saudi Arabia, Negaa M. Albegami

Doctoral Dissertations

"A major activity within the systems engineering process is the requirements definition and analysis phase. In technical systems, planning this phase looks too technical for top management and too broad for the engineers specialized in narrow technical fields. This categorization (too technical/too broad) represents a gap between top management and specialized engineering. In Saudi Arabia, such a gap is believed to be very wide.

The main objective of this research is to find a way to narrow this gap between management and engineering when planning government systems, especially in electronic warfare (EW) systems. A solution in this effort is to …

Behavior Of Arc Spot Weld Connections In Tension, Roger A. Laboube, Wei-Wen Yu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Arc spot welds, commonly called puddle welds, are widely used for connecting cold-formed steel roof decks to their supporting members. These support members are typically hot-rolled steel beams or girders, or the top chord of open-web steel joists. A comprehensive experimental study of the tension strength of arc spot weld connections used to affix a cold-formed steel roof deck to its support member was conducted. The study investigated the key parameters that influence the connection strength: Steel thickness, tensile strength, and ductility; type of weld process, automatic or manual; cross section of the roof deck; loading condition, symmetrical or eccentric …

Flexural Behavior Of Web Elements With Openings, Roger A. Laboube, Wei-Wen Yu, Ming-Yang Shan

CCFSS Library (1939 - present)

No abstract provided.

Simulation De L'Interaction Entre Le Voilement Local Et Les Modes Globaux D'Instabilite Des Profils A Froid Par Une Combinaison De La Methode Des Largeurs Effectives Et De L'Element Fini Non-Lineaire De Poutre Spatiale, Luiz Felippe Estrella Jr.

CCFSS Library (1939 - present)

The objective of this thesis is the study of the stability of cold-formed thin-walled steel members. The interaction between global instability and local buckling of the profile walls has a reducing effect on the collapse load. The aim is to develop a numerical tool able to predict not only the collapse load, but also the equilibrium path. With this aim in view, the non-linear spatial beam tinite element recently developed by Vincent de Ville in Liege University was chosen for this purpose. The steel member is considered as an association of flat plates and corners. Local buckling is modeled by …

Decision-Support Tools For Transferring Am/Fm/Gis To Small Communities, Steven W. Mccrary, Colin Othniel Benjamin, Peter J. Schmidt

Engineering Management and Systems Engineering Faculty Research & Creative Works

This paper examines several decision-support tools for transferring AM/FM/GIS technology to small communities. The term Computer-Assisted Spatial Information Systems (CASIS) provides a basis for a systematic categorization and definition of AM/FM/GIS systems that will serve to enhance small communities' understanding of these technologies for future decisions. The acronym CASIS includes such areas as database-management systems, automated mapping/facilities management/geographic information systems (AM/FM/GIS), and computer-aided drafting (CAD). Further, this paper reports the highlights of a survey that assesses the theory-practice gap in AM/FM/GIS usage among very small local government agencies. The survey uncovered an existing theory-practice gap: A, slow rate of system …

Galvanic Stripping Of Fe⁺³ And Pb⁺² Ions And Dissolution Of Metallic Fe, Zn, Pb And Cd Using Di(2-Ethylhexyl)Phosphoric Acid, Luis Miguel Chia Aquije

Doctoral Dissertations

"Two systems were evaluated using the principles of the galvanic stripping process. One of them, the removal of Pb⁺² ions from di-2(ethylhexyl) phosphoric acid (D2EHPA) was performed using metallic zinc. The other, the removal of Fe⁺³ ions from D2EHPA used metallic iron as reductant and was performed simultaneously with the organic phase using a slightly acidic aqueous solution of hydrochloric acid. In addition, the dissolution of metallic zinc, iron, lead, and cadmium in D2EHPA was studied in order to better understand the anodic step in the mechanism of the galvanic stripping process.

Increased temperature was found to dramatically …

Progress In Coal Pyrolysis, Peter R. Solomon, Thomas H. Fletcher, Ronald J. Pugmire

Faculty Publications

The heterogeneous nature of coal and the complexity of the pyrolysis process have made it very difficult to perform unambiguous experiments to determine the rates and mechanisms in coal pyrolysis. However, recent years have seen a number of new experimental and theoretical approaches which shed new light on the subject. This paper considers the recent progress on kinetics, the formation of volatile products, network models, cross-linking, rank effects, and the ‘two-component’ model of coal structure. Recent experiments which measured coal particle temperatures at high heating rates provide reasonable agreement on kinetic rate constants. These rates also agree with those derived …

Observation Of The Charmed Baryon C+ And Measurement Of The Isospin Mass Splittings Of The C, Crawford, G.; Et Al., M. Thulasidas

Research Collection School Of Computing and Information Systems

No abstract provided.

Rio Mimbres Acequia Systems: An Oral History, Neal W. Ackerly

Books

This volume contains transcripts of interviews with various residents collected during the 1993 field phase of the survey of acequia systems in the Mimbres Valley. As noted in Volume 1, additional interviews were conducted with other residents, but were not recorded. Accordingly, no transcript of these interview sessions cannot be included here.

The individuals interviewed, as well as the abbreviated names appearing in these transcripts, included John VonTress (JVT, age 57), Regis McSherry (RM, age 67), Sam Grijalva (age 73), Charles Disert (age 84), and Horace Bounds (HB, age 90). Vesta McSherry, appearing as VM in transcripts, provided additional information …