Engineering Commons^™

Dynamic Response Of A Compressor Research Facility, Janet W. Grondin

Theses and Dissertations

The response of the Wright Laboratory Compressor Research Facility to a small amplitude, acoustic, sinusoidal disturbance was investigated. The fluid transmission line equations for laminar, one-dimensional flow in a circular duct were solved and verified through a laboratory experiment using a scale model of the facility. The resonant frequencies of the facility were determined for a variety of flow conditions. Techniques for analytically modeling end impedance and flow straightening elements were also studied. The fundamental frequency of the facility was determined to be between 5.5 and 6.5 Hz depending on the flow conditions and geometry configurations specified.

Rendering Of Three-Dimensional Data Sets Derived From Finite-Difference And Spectral Methods, Paul A. Schubert

Theses and Dissertations

The timely visualization of three-dimensional data sets and the advantages of using a spectral method solution versus a finite-difference method solution in rendering isosurfaces is described. The Beam-Warming numerical algorithm, which uses implicit-approximate-factorization, is used to generate the steady-state solutions for a model diffusion-convection problem. The Chebyshev collocation operator is used to evaluate the right-hand side of the Beam-Warming algorithm for the spectral solution. Comparing the model problem results with the exact solution, the spectral series solution is truncated to the same degree of accuracy as the finite-difference for comparison of rendering times. The rendering algorithm employs octrees to efficiently …

Design And Construction Of The Aerobot Robotic Manipulator (Arm), William L. Cochran

Theses and Dissertations

This thesis designed, constructed, and tested a robotic arm for the Aerobot Aerial Robot. The main purpose of the ARM is to enable the Aerobot to retrieve objects for use in an annual robotics competition. Design of the ARM involved synthesizing the characteristics of simplicity, weight, strength, and size. The result was a three-degree-of-freedom manipulator that uses electric motors, cable linkages, and telescoping tubes to access a work space below the Aerobot. Forward and inverse kinematics were investigated to enable automation of the ARM. Data was collected from infrared sensors to validate the model. Manipulation of the ARM is presently …

Automating Satellite Range Scheduling, S. Michael Schalck

Theses and Dissertations

The objective of this study was to develop a computer based satellite range scheduling SRS algorithm to create a 24 hour satellite support schedule. The algorithms goal was to schedule as many satellite support requests as possible. An iterative heuristic approach was used to schedule satellite support requests in three successive sub problems. The first sub problem involves scheduling low altitude satellite support requests using a mixed integer programming approach. The next two sub problems each involve scheduling 12 hour blocks of medium and high altitude satellite support requests, again using a mixed integer programming approach. Fourteen 24 hour schedules …

Nitric Oxide Production: A Mechanism For Inhibition Of Chlamydia Trachomatis Replication, Bojun Chen

Electronic Theses and Dissertations

Chlamydia trachomatis (CT) replicates in macrophages, but is inhibited by IFN-$\gamma$ or LPS. IFN-$\gamma$ and/or LPS induced nitrite production in mouse peritoneal macrophages, macrophage cell lines (RAW264.7 and J774A.1) and McCoy cells. Kinetic studies indicated that peak production occurred 48 hours post-treatment. CT infection itself was insufficient to induce nitrite production, but resulted in enhancement of nitrite production in IFN-$\gamma$-treated cells. Treatment with IFN-$\gamma$ or LPS resulted in significant inhibition of CT replication in these cells. Strong correlation between nitrite production and inhibition of CT replication was observed in RAW264.7 and J774A.1 cells (correlation coefficients: $-$0.93 and $-$0.94, p $<$ 0.001). N$\sp{\rm g}$- monomethyl-L-arginine (L-NMMA) specifically inhibited nitrite production and partially reversed inhibition of CT replication in macrophage cell lines. NOS mRNA was measured in RAW264.7 cells by Northern blot and Dot blot hybridization. Strong correlation between NOS mRNA expression and inhibition of CT replication (correlation coefficient: $-$0.97, p $<$ 0.05) was observed. Anti-TNF-$\alpha$ antibody completely neutralized the biological activity of TNF-$\alpha$ secreted by LPS-treated RAW264.7 cells, yet the antibody neither reduced nitrite production nor restored CT replication. Combination of the antibody and L-NMMA significantly enhanced restoration of CT replication. In peritoneal macrophages, inhibition of CT replication induced by IFN-$\gamma$ was partially restored by L-NMMA or anti-TNF-$\alpha$ antibody. In McCoy cells, inhibition of CT replication induced by IFN-$\gamma$ and LPS was not significantly restored by L-NMMA. Great restoration of CT replication by 1 mM L-NMMA was observed in LPS-treated J774A.1 cells (31%), but not in IFN-$\gamma$-treated cells (5%). Our data indicate that (1) NO production is one of the mechanisms for inhibition of CT replication in IFN-$\gamma$-activated peritoneal macrophages and RAW264.7 cells; (2) NO plays a significant role in CT inhibition in LPS-treated macrophage cell lines, but not peritoneal macrophages; (3) TNF-$\alpha$ may be associated with inhibition, but the mechanism(s) may not involve NO production; (4) NO production may not be the mechanism for CT inhibition in McCoy cells treated with IFN-$\gamma$ and LPS.

Modeling And Simulation Of Bipolar Transistor At Low Temperature, Swarupa Madhav Nerurkar

Dissertations and Theses

The BICMOS technology which integrates the CMOS technology with bipolar technology has drawn considerable attention as an attractive VLSI technology because of the high speed performance and low power consumption of the BICMOS. However, continued down scaling of CMOS devices has caused increased concerns with problems such as latch up, hot carriers and short channel effect. Most of the above mentioned problems can be avoided by operating the CMOS at liquid-nitrogen temperature(LNT). At low-temperatures, the CMOS exhibits lower sub threshold leakage, higher carrier mobility (which yields improved speed performance), and a steeper logarithmic currentvoltage slope. On the other hand, the …

Simple High-Quality Lossy Image Coding Scheme, Shaolin Bi, Khalid Sayood

Department of Electrical and Computer Engineering: Faculty Publications

A simple yet efficient image data compression method is presented. This method is based on coding only those segments of the image that are perceptually significant to the reconstruction of the image. Sequences of image pixels whose gray-level differences from the pixels of the previous row exceed two prespecified thresholds are considered significant. These pixels are coded using a differential pulse code modulation scheme that uses a 15-level recursively indexed nonuniform quantizer for the first pixel in a segment and a 7-level recursively indexed nonuniform quantizer for all other pixels in the segment. The quantizer outputs are Huffman coded. Simulation …

Constructed Wetlands As An Innovative, Cost-Effective Solution For Wastewater Treatment In Small Communities, Christy Womack Vines

Honors Capstone Projects and Theses

No abstract provided.

Ionic Charge Dependence Of The Zero Degree Binary Encounter Peak For Partially Stripped Heavy Ions, W. Wolff, H. E. Wolff, J. L. Shinpaugh, Jee-Ching Wang, Ronald E. Olson, D. Fainstein, S. Lencinas, U. Bechthold, R. Herrmann, H. Schmidt-Bocking

Chemical and Biochemical Engineering Faculty Research & Creative Works

We report on the measurements of double differential cross sections, at zero degree, for the production of secondary electrons from the collision of 0, 6 MeV amu^-1 Cu⁵⁺, I⁷⁺, Au¹¹⁺, U¹³⁺, Cu¹⁹⁺, t²³⁺ and Au²⁹⁺ projectiles with H₂ and He. The shapes and positions of the observed binary encounter electron peaks are compared with continuum distorted wave-eikonal initial state (CDW-EIS), impulse approximation and classical trajectory Monte Carlo calculations, as well as with predictions from an adiabatic resonant tunnelling model recently proposed by Fainstein and co-workers. The …

Pattern Recognition And Erp Waveform Analysis Using Wavelet Transform, Hong Qi

Dissertations and Theses

Wavelet transform provides an alternative to the classical Short-Time Fourier Transform (STFT). In contrast to the STFT, which uses a single analysis window, the Wavelet Transform uses shorter windows at higher frequencies and longer windows at lower frequencies. For some particular wavelet functions, the local maxima of the wavelet transform correspond to the sharp variation points of the signal. As an application, wavelet transform is introduced to the character recognition. Local maximum of wavelet transform is used as a local feature to describe character boundary. The wavelet method performs well in the presence of noise. The maximum of wavelet transform …

High Power Edge-Emitting Light Emitting Diodes At 1.5Μ With Extremely Low Back Facet Feedback, J. E. Fouquet, G. R. Trott, W. V. Sorin, M. J. Ludowise, D. M. Braun, Dennis J. Derickson

Electrical Engineering

This paper describes novel semiconductor sources for optical low coherence reflectometry (OLCR), a measurement technique for characterizing device and fiber reflections with high sensitivity and high spatial resolution. Lasers and conventional superluminescent LEDs are not suitable for OLCR because strong reflections from the back facets mask weak reflection signals from the device or fiber under test. Even standard edge emitting LEDs (EELEDs) show significant reflections, which have limited the dynamic range of previous measurements. Low source output powers have also limited sensitivity. In order to obtain high power while minimizing internal reflections, a high single pass gain device is required. …

Explanation Of Timing Jitter Mechanisms In Multisegment Mode-Locked Semiconductor Lasers, Dennis J. Derickson

Electrical Engineering

Multisegment mode-locked semiconductor lasers offer a simple, high performance solution for short pulse generation. Six mode-locking techniques used in multisegment mode-locked semiconductor lasers are shown. This paper concentrates on a theoretical explanation of the timing jitter mechanisms in these lasers with supporting experimental measurements. The analysis covers passive, hybrid, and active mode-locking techniques for both monolithic and external cavity devices. Timing jitter is a very important system consideration for most applications of mode-locked lasers.

Obscured Object Detection Via Bayesian Target Modeling Techniques, Rufus H. Cofer

Electrical Engineering and Computer Science Faculty Publications

Underground objects are by nature often severely obscured although the general character of the intervening random media may be reasonably understood. The task of detecting these underground objects also implies that their exact location and or orientation is not known. To partially counter these difficulties, one may; however, be given a model of the target of interest, e.g. a particular tank type, a water pipe, etc. To set up a quality framework for solution of the above problem, this paper utilizes the paradigm of Bayesian decision theory that promises minimum error detection given that certain probability density functions can be …

Rate Equations For The Phonon Peak In Resonant-Tunneling Structures, Roger Lake, Gerhard Klimeck, J. P. Anantram, Supriyo Datta

Birck and NCN Publications

The ratio of the phonon peak current to the main peak current in double-barrier resonant-tunneling structures is significantly enhanced by barrier asymmetry. Previously, using the Keldysh formalism, we derived analytical expressions, valid in the zero-temperature, high-bias regime, which explained this eftect. We now provide analytical expressions valid for finite temperature and bias obtained from (i) an intuitive derivation using a rate equation approach and (ii) a more general derivation using the Keldysh formalism. The results of the two difFerent approaches are shown to be essentially identical for the ex- perimental device parameters. The finite temperature expressions shed light on the …

Investigation Of Solution Space Of Trees And Dags For Realization Of Combinational Logic In At 6000 Series Fpgas, Philip Ho

Dissertations and Theses

Various tree and Directed Acyclic Graph structures have been used for representation and manipulation of switching functions. Among these structures the Binary Decision Diagrams have been the most widely used in logic synthesis. A BDD is a binary tree graph that represents the recursive execution of Shannon's expansion. A FDD is a directed function graph that represents the recursive execution of Reed Muller expansion.

A family of decision diagrams for representation of Boolean function is introduced in this thesis. This family of Kronecker Functional Decision Diagrams (KFDD) includes the Binary Decision Diagrams (BDD) and Functional Decision Diagrams (FDD) as subsets. …

Local Needs Implementation For All Programs, James G. Harris, Madeleine M. Johnson, Norm Rogers, Jay Waddell

Electrical Engineering

SYNTHESIS is one of four ex1sting NSF Engineering Education Coalitions (there are apparently plans to add two others this year to bring the total number to six). SYNTHESIS consists of eight universities: Cal Poly, Cornell. Hampton, Iowa State, Southern, Stanford, Tuskgekee, and UC-Berkeley. It has been supported by NSF for over three years, being one of the first two-the other being ECSEL. The other two existing coalitions are GATEVI/AY and SUCCEED. One 9f the main goals of the 'SYNTHESIS coalition is the development of the National Engineering Education Dehvery System (NEEDS). After giving a brief overv1ew of the NEEDS, we …

National Engineering Education Delivery System (Needs), Alice M. Agogino, Sheri Sheppard, Kate Mink, James G. Harris, Lawrence Genalo, Jaya Krishnagopalan, Dave Martin, John Saylor

Electrical Engineering

The Synthesis Coalition, supported by the National Science Foundation and industrial partners, is comprised of the following eight educational institutions: California Polytechnic State University at San Luis Obispo, Comell, Hampton, Iowa State, Southern, Stanford, and Tuskegee Universities, and the University of California at Berkeley (1].

The National Engineering Education Delivery System (NEEDS) is an entirely new courseware development and distribution system which will provide Widespread, rapid, electronic access to an almost arbitrarily large number of diverse instructional modules (2-4). Curricular material in the NEEDS database are organized by a diverse range of indices. Links across disciplines are provided in the …

Vertex Ordering For A Partitioning-Based Fitting Algorithm For An Epld Device, Tongjun Gao

Dissertations and Theses

As the Application-Specific Integrated Circuit(ASIC) technology develops to the trend of high density and modulization, the ASIC device market has been dominated gradually by the more complex Erasable Programmable Logic Devices (EPLDs) and the Field Programmable Gate Array(FPGAs) instead of the ordinally Programmable Logic Devices(PLDs). Meanwhile, the design automation system for such programmable devices has also moved from schematic entry design to high level hardware description language entry design. Usually, the whole design automation process consists of three phrases, the high level hardware description language compiler, the logic synthesis stage and the layout synthesis stage. Though the layout synthesis stage …

Wright State University College Of Engineering And Computer Science Bits And Pcs Newsletter, Volume 9, Number 9, November 1993, College Of Engineering And Computer Science, Wright State University

BITs and PCs Newsletter

A fourteen page newsletter created by the Wright State University College of Engineering and Computer Science that addresses the current affairs of the college.

Acuta Enews November 1993, Vol. 22, No. 11

ACUTA Newsletters

In This Issue

Board Report

President's message

TASA commissions

Numbering plan means net manager pains

21st Century Technology

Toll Fraud

Sensitivity Improvement Of A 1-Μm Ladar System Incorporating An Active Optical Fiber Preamplifier, Michael S. Salisbury, Paul F. Mcmanamon, Bradley D. Duncan

Electro-Optics and Photonics Faculty Publications

In an effort to increase the SNR of a continuous wave, 1-μm all solid state ladar system, a rare-earth-doped optical fiber amplifier is investigated as a preamplifier for ladar return signals. The experimental system is detailed and a theoretical analysis of the fiber amplifier's effect on both heterodyne and direct detection schemes is provided. Beginning with the optical powers incident on the detector, the signal and noises are analyzed, through the detector electronics, to predict the SNR. The SNR is then plotted as a function of the return signal power, and a SNR threshold is defined to determine a minimum …

Electrorheological Fluids And Their Application In Automotive Clutches: Design Procedures And Recommendations, Ihab Fahmy

Archived Theses and Dissertations

No abstract provided.

Behavior Of Concrete Masonry Prisms Under Axial Compression, Tarek Ghoneim Mohamed Ghoneim

Archived Theses and Dissertations

No abstract provided.

Crew Scheduling Of Space Operations Squadrons (Sops), Marianne Idzi

Theses and Dissertations

The mission of Space Operations Squadrons is continuous support of military satellite systems. The scheduling problem associated with conducting continuous operations is threefold. The first problem is finding cyclical crew shift schedules that meet daily manning requirements, adhere to current regulations, contain a minimum number of workshift changes during consecutive duty days, and maximize the non-duty time allowed between duty shifts. The second problem is to establish a sea of criteria to evaluate alternative shift schedules. Finally, the third problem is to minimize the number of personnel required to meet the scheduling requirements stated in the first problem. This study …

The Application Of Simulated Annealing To Stochastic Systems, Charles B. Warrender

Theses and Dissertations

Simulated Annealing was used to optimize three constrained simulation models. For each of these models, seven different acceptance functions were evaluated and compared against the performance of Local Search. These comparisons demonstrated the affect that different acceptance functions have on the performance of the algorithm. The performance was measured by the average solution quality and average efficiency obtained from several runs. The first model facilitated the implementation of Simulated Annealing using the SLAM simulation language. The configuration space was small, described by only two decision variables. It demonstrated the viability of using Simulated Annealing to optimize the variable settings in …

A Kinematically Intelligent Blackboard For Computer Aided Instruction, J. Keith Nisbett, D. Watkins, Clark R. Barker

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A CAI (computer-aided instruction) package is being developed to be used as a classroom tool for the instruction of undergraduate mechanical engineering students in an introductory kinematics of mechanisms course. This graphical environment allows the instructor to emulate on the projected graphics screen everything that is currently done on the blackboard for planar mechansims. Unlike the blackboard, the software will have the intelligence to interpret the drawings in a kinematic sense so that the drawing of the linkage will behave as a linkage. The software environment involves three principal components: (1) a sketching method for defining the linkage, (2) the …

A Summary Of Highway Revenues, Expenses And Distributions: 1986 Through 1993, Herpicc

Indiana Local Technical Assistance Program (LTAP) Publications

This report shows the history of receipts, expenses and distributions of revenues that provide funding to all local governments for highway, road and street work.

A Robust Aggregation Approach To Simplification Of Manufacturing Flow Line Models, Paul Savory

Department of Industrial and Management Systems Engineering: Faculty Publications

One of the more difficult tasks facing a modeler in developing a simulation model of a discrete part manufacturing system is deciding at what level of abstraction to represent the resources of the system. For example, questions about plant capacity can be modeled with a simple model, whereas questions regarding the efficiency of different part scheduling rules can only be answered with a more detailed model. In developing a simulation model, most of the actual features of the system under study must be ignored and an abstraction must be developed. If done correctly, this idealization provides a useful approximation of …

S/O Modeling Technique For Optimal Containment Of Light Hydrocarbons In Contaminated Unconfined Aquifers, Grant S. Cooper Jr., Jagath J. Kaluarachchi, Richard C. Peralta

Civil and Environmental Engineering Faculty Publications

An innovative approach is presented to minimize pumping for immobilizing a floating plume of a light non-aqueous phase liquid (LNAPL). The best pumping strategy is determined to contain the free oil product and provide for gradient control of the water table. This approach combined detailed simulation, statistical analysis, and optimization. This modeling technique uses regression equations that describe system response to variable pumping stimuli. The regression equations were developed from analysis of systematically performed simulations of multiphase flow in an areal region of an unconfined aquifer. Simulations were performed using ARMOS, a finite element model. ARMOS can be used simulate …

A Nonlinear Three-Dimensional Micromechanics Model For Fiber-Reinforced Laminated Composites, David D. Robertson

Theses and Dissertations

In this study, a three-dimensional micromechanics model is developed. The present capabilities of the model include both unidirectional and laminated composite layups with various types of nonlinear analysis such as a thermoelastic-plastic analysis employing the Prandtl-Reuss flow relations, a thermoviscoplastic analysis using Bodner-Partom unified constitutive theory, and an interfacial damage progression scheme based on a statistical interfacial failure criteria. Such nonlinearities are critical factors during thermomechanical fatigue TMF loading of high temperature composites. Solutions were obtained and extensive comparisons performed with existing micromechanics models, finite element analysis, and experiment with excellent results. In addition, the analysis was developed to require …