Engineering Commons^™

Intercomparison Between Commercial Condensation Nucleus Counters And An Alternating Temperature Gradient Cloud Chamber, Darryl J. Alofs, C. K. Lutrus, Donald E. Hagen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Three Commercial CNC Counters (TSI Models 3010, 3022A, and 3025A) Are Compared with an Alternating Temperature Gradient Cloud Chamber (ALGR). Electrically Size Classified Aerosols of Sodium Chloride and Silver Are Used. Diffusional Losses within the ALGR Are Much Larger Than for the TSI Instruments: Therefore the ALGR Concentrations Are Corrected for Internal Diffusional Losses, But the TSI Instruments Are Not. the Particle Size Range Tested is 4–90 Nm. for Sodium Chloride, the TSI Concentrations Agreed Fairly Well with the Corrected ALGR at Larger Sizes, and Were Below the Corrected ALGR at Smaller Sizes. the Electrical Aerosol Classifier (EAC) Setting at …

Scheduling Of Parallel Jobs On Dynamic, Heterogenous Networks, Dan Clark, Jeremy Casas, Steve Otto, Robert Prouty, Jonathan Walpole

Computer Science Faculty Publications and Presentations

In using a shared network of workstations for parallel processing, it is not only important to consider heterogeneity and differences in processing power between the workstations but also the dynamics of the system as a whole. In such a computing environment where the use of resources vary as other applications consume and release resources, intelligent scheduling of the parallel jobs onto the available resources is essential to maximize resource utilization. Despite this realization, however, there are few systems available that provide an infrastructure for the easy development and testing of these intelligent schedulers. In this paper, an infrastructure is presented …

Investigation Of The Relationship Between Fuel Injection Nozzle Roto Flow And Hydra Flow And The Engine Torque Of A Diesel Engine, Guang Jin

Dissertations and Theses @ UNI

The purpose of this study was to investigate the possibility of reducing diesel engine torque variation by optimizing fuel injection nozzle tip configuration. In order to reduce engine torque variation, test runs were conducted to determine whether fuel injection nozzles affected diesel engine torque. There was a further effort to determine whether a correlation existed between the fuel injection nozzle roto flow and hydra flow, and the engine torque at specified engine speeds.

Engines installed in cotton pickers and tractors were used for this study. Engines, five from the cotton picker and five from the tractor group were chosen randomly …

Effect Of Agricultural Fiber Reinforcement On The Mechanical Properties Of A Recycled Polyethylene Plastic Composite Material, Michael E. Courbat

Dissertations and Theses @ UNI

This study determined the effect of certain agricultural fiber reinforcements on the tensile and impact mechanical properties of a recycled polyethylene plastic composite material. The purpose of the study was to provide information on certain mechanical properties of a recycled polyethylene plastic material as part of a coordinated materials application process.

A prototype product run of the plastic composite material was done and test specimens were selected from this material. Notch impact, tensile, and flexure tests were conducted on test specimens. Test procedures complied with accepted standards from The American Society For Testing and Materials (ASTM). Tests were conducted on …

An Analysis Of The Use Of Programmable Controllers To Control An In Situ Leach Mine Wellfield, Jimmy W. Stokey

Dissertations and Theses @ UNI

In situ mining is a relatively new method that has the potential of recovering a variety of minerals. This process is quickly becoming an alternative to conventional mining techniques that are environmentally unsound. Two problems associated with in situ mining are, the amount of waste water generated by the process (bleed) and the uncontrolled migration of lixiviant outside the production zone (an excursion).

The purpose of this study was to determine if in situ mining processes could be monitored and controlled with a Sequential Control and Data Acquisition (SCADA) system. Using programmable logic controllers, a cost-effective SCADA system was designed …

Impact Of Erosion, Mass Wasting, And Sedimentation On Human Activities In The Río Grande Basin, Jujuy Province, Argentina, Waldo Chayle, William J. Wayne

Department of Earth and Atmospheric Sciences: Faculty Publications

Nearly all dry mountainous regions are affected by severe erosion, floods, and debris flows during times of intense precipitation. The lithology, geologic structure, and climate in Jujuy Province, Argentina combine to place at serious risk the people who live along the Río Grande, the major river that drains the east side of the Cordillera Oriental and the west side of the Sierras Subandinas. Nearly all precipitation falls during summer (January–March) with little during the remainder of the year; most of the basin is semiarid to arid, although the southern end has a humid subtropical climate. Relief is great, as much …

The Multirate Simulation Of Facts Devices In Power System Dynamics, J. G. Chen, Mariesa Crow

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, the multirate method is applied to the problem of simulating the dynamics of a power system which contains fast components such as induction machine loads and FACTS devices. Results concerning the numerical stability and accuracy of the multirate method are presented. Implementation concerns are also addressed by studying an example power system which contains a wide range of time response behavior

A Bipartite, Differential I Ddq Testable Static Ram Design, Waleed K. Al-Assadi, A. P. Jayasumana, Y. K. Malaiya

Electrical and Computer Engineering Faculty Research & Creative Works

I DDQ (Defect Detection by Quiescent power supply current measurement), or current testing, has emerged in the last few years as an effective technique for detecting certain classes of faults in high-density ICs. In this paper, a testable design that enhances the I DDQ testability of static random access memories (SRAMs) for off-line testing as proposed. To achieve high accuracy and a test speed approaching the system operational speed, the memory is partitioned for comparison of I DDQ values. Parallel write/read operations are used to activate possible faults, while quiescent power supply currents from two blocks are compared

Hamiltonian Based Adaptive Critics For Aircraft Control, S. N. Balakrishnan, Jie Shen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Aircraft designs are becoming more complex in order to either operate more efficiently as in the commercial sector or to push the performance envelopes as in the military sector. An interesting outcome of this scenario is that `control'' has come to play an important role in helping realize these objectives. Increasingly, control is becoming an integral part of an aircraft design rather than an afterthought. More effective and efficient control of an aircraft is certain to lead to improved performance at a lower cost

A New Approch To Low Drift Ta₂O₅ By Ph Reactive Sputtering And Sol-Gel Method, Chang-Soo Kim, Dae-Hyuk Kwon, Byung-Woog Cho, Byung-Ki Sohn

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

A New Ph-Isfet Based Dissolved Oxygen Sensor, Chang-Soo Kim, Dae-Hyuk Kwon, Byung-Ki Sohn

Electrical and Computer Engineering Faculty Research & Creative Works

"A new dissolved oxygen sensor based on pH-ISFET has been discussed. A platinum working electrode surrounding a pH-sensing gate of the pH-ISFET electrolyzes dissolved oxygen, resulting in a corresponding pH change. The pH-ISFET can determine dissolved oxygen concentration through detecting this pH change."--Summary

A Universal Power Converter For Emergency Charging Of Electric Vehicle Batteries, Norman R. Cox

Electrical and Computer Engineering Faculty Research & Creative Works

An on-board electric vehicle battery charger capable of accepting AC or DC inputs in the range of 12 to 260 volts is described. The charger provides near-unity power factor and high efficiency for routine charging from AC sources, but can also be used to tap other sources of power in the event of an emergency.

The Structure And Phase Equilibria Of Salt-Water Solution At Supercritical Conditions, S. T. Cui, J. G. Harris

Electrical and Computer Engineering Faculty Research & Creative Works

We study the thermodynamic properties of the supercritical water and dilute aqueous salt solutions using molecular dynamics simulation, The sodium and chloride ions are found to show strong pairing at conditions corresponding to those of supercritical water oxidation, we also present the first prediction of the solubility of sodium chloride in supercritical water obtained directly from intermolecular interactions using molecular simulations. © 1995 Plenum Publishing Corporation.

Optimizing Object Invocation Using Optimistic Incremental Specialization, Jon Inouye, Andrew P. Black, Charles Consel, Calton Pu, Jonathan Walpole

Computer Science Faculty Publications and Presentations

To make object invocation efficient, it is important to minimize overhead. In general, overhead is incurred in order to maintain transparency; with the advent of mobile computer systems, persistence, increasing security and privacy concerns, transparency becomes more expensive and overhead is increasing. Invocation mechanisms maintain transparency by finding objects, choosing communication media, performing data translation into common formats (e.g., XDR), marshalling arguments, encrypting confidential data, etc. Performing all of these operations on every invocation would lead to unacceptable performance, so designers often avoid operations by specializing object invocation for more restricted environments. For example, the Emerald compiler performs several optimizations …

Hardware Assists For High Performance Computing Using A Mathematics Of Arrays, Hardy J. Pottinger, W. Eatherton, J. Kelly, T. Schiefelbein, Lenore Mullin, R. Ziegler

Electrical and Computer Engineering Faculty Research & Creative Works

Work in progress at the University of Missouri-Rolla on hardware assists for high performance computing is presented. This research consists of a novel field programmable gate array (FPGA) based reconfigurable coprocessor board (the Chameleon Coprocessor) being used to evaluate hardware architectures for speedup of array computation algorithms. These algorithms are developed using a Mathematics of Arrays (MOA). They provide a means to generate addresses for data transfers that require less data movement than more traditional algorithms. In this manner, the address generation algorithms are acting as an intelligent data prefetching mechanism or special purpose cache controller. Software implementations have been …

Model Parameter And Time Delay Estimation In The Frequency Domain, Aidan O'Dwyer, John Ringwood

Conference papers

This paper discusses the estimation of the parameters (including the time delay) of single input, single output (SISO) process models from an appropriate number of arbitrarily specified points on the process frequency response. The method involves combining an analytical approach with a least squares approach using a gradient algorithm, to provide accurate and robust estimates of the parameters.

Study Of The Time Efficiency And Volume Of Wood Used For Three Types Of Stove In The Salitrón Community Of San Juan Ermita, Department Of Chiquimula, Fredy Samuel Coronado López

Theses and Dissertations

In developing countries such as Guatemala, firewood is increasingly being used for cooking in most rural areas. Consequently, there is a shortage of firewood in these areas beca use trees do not grow at the same rate as they are consumed. Some authors report that 90% of the heat from firewood is lost during combustion. Several alternatives to open pit fires exist to reduce the amount of firewood used. However, these alternatives need to be evaluated to determine their efficiency. This project compared the time efficiency and volume of firewood used in the Finlandia style improved stoves, Josefina stoves, and …

Calculating Cross Slot Flux Losses In High Voltage Stator Coils, John D. Amos

Retrospective Theses and Dissertations

At present there are several methods for calculating temperature for inner-cooled stator coils for large electric generators. Determining the highest temperature in a stator coil is very important and is a major limiting factor for the maximum capability of steam turbine synchronous generators.

The load current in the stator winding causes losses in the conductor resistance. That same current excites leakage fluxes that link contours inside the conductors causing non-uniform current distribution and additional losses. these additional losses are caused by eddy currents induced inside the stator coils. These eddy losses are grouped as radial flux losses, cross slot flux …

Gaussian Beam Resonator Formalism Using The Yy Method, Kenneth A. Menard

Retrospective Theses and Dissertations

A simple and powerful new paraxial ray formalism is shown to provide an alternate method for designing Gaussian Beam Resonators. The theory utilizes the Delano yybar diagram approach and is an extension of the recent work by Shack and Kessler for laser systems. The method is shown to be complementary to the conventional ABCD method and is founded upon J.A. Arnaud's pioneering ideas for complex rays. The thesis develops an analytic formulation of a ray based complex wavefront curvature and yields a clearly generalized description of spherical wave propagation, for which Gaussian beams are considered a special case. The resultant …

Electrical And Thermal Transport Properties Of (La,Ca)(Cr,Co)O3, Rasit Koc, Harlan U. Anderson

Materials Science and Engineering Faculty Research & Creative Works

DC electrical conductivity and Seebeck data as functions of temperature and oxygen activity were used to explain the electrical and thermal transport properties of (La,Ca) (Cr,Co)O3. The electrical conductivity data of La (Cr,Co)O3 suggested that it depends upon Co content. At Co concentrations less than 20 mol%, Co acted as traps for the carriers and decreased the electrical conductivity of the compositions at temperatures less than 900 °C. As the Co concentration increased to above 20 mol%, electrical conductivity increased significantly due to a connecting path of available Co sites. Additional Ca substitution for La increased the electrical conductivity in …

La Résistance Des Gants À La Coupure : Développement D'Une Méthode D'Essai, Jaime Lara, Denis Turcot, Renaud Daigle, Jérôme Boutin

Rapports de recherche scientifique

No abstract provided.

The Design Of Fir Filters With Linear Or Non-Linear Phase Using The Kaiser Window Function And A Novel Superposition Method, Cai Zurong

Retrospective Theses and Dissertations

A new design method for FIR filters using the Kaiser window is presented in this paper. Near optimal frequency response and impulse response can be obtained for a given • set of specifications. The synthesis procedure uses the summation of frequency translated and scaled Kaiser functions. The method can be used to design linear phase or non-linear phase filters, and symmetric or non-symmetric arbitrary magnitude response filters. This design method is based on the frequency domain using the approximate Fourier transform of the Kaiser window function. The design procedures and examples for linear and arbitrary phase filters are discussed in …

Diagnostics Of Cdte Electrodeposition By Rest Potential Voltammetry, Brandon Kemp, Robert Engelken, Arif Raza, Arees Siddiqui, Omer Mustafa

Journal of the Arkansas Academy of Science

Due to the extreme sensitivity of the partial elemental currents (i.e.,iCd, iTe) and, hence, stoichiometry to deposition voltage, temperature, mass transport, and ambient light intensity during electrodeposition of semiconductor films, it is important to implement in-situ methods for monitoring the stoichiometry and related semiconductor efficacy of the growing film. We report investigation of open circuit rest potential (Eoc) voltammetry as one such method during electrodeposition of CdTe from aprotic electrolytes such as ethylene glycol. Plots of transient open circuit potential versus sweep voltage exhibit distinct transition and plateau structures corresponding to Te, CdTe, and Cd phases and correlating with the …

Construction Resource Allocation Using A Genetic Algorithm, Siripong Malasri, Jennifer R. Martin

Journal of the Arkansas Academy of Science

A proper allocation of limited resources (men, machines, materials, and money) is critical in a construction project. Traditionally, resource allocation problems have been solved using methods in operations research (OR), such as mathematical programming. In recent years, genetic algorithms (GA) have emerged as an effective optimization methodology. One major advantage of the GA approach over the OR approach is that the GA approach is universal for various types of optimization problems, unlike the OR approach which varies depending on the types of problems at hand. This paper shows an application of GA to a resource allocation problem in the construction …

Retrieval Of Atmospheric Turbidity Coefficiant And Water Column Density Fro Solar Irradiance Data, Felix Tendeku

Journal of the Arkansas Academy of Science

Ground-based measurement of solar irradiance has been made using a spectroradiometer at wavelengths inapx-water absorption band. An algorithm is formulated to retrieve simultaneously the atmospheic water column density and Angstrom's turbidity coefficient. The transmission models used to account for the contribution from diverse atmospheic absorbing and scattering elements are presented.

Catalyst Wetting Efficiency In Trickle-Bed Reactors At High Pressure, Muthanna H. Al-Dahhan, Milorad P. Duduković

Chemical and Biochemical Engineering Faculty Research & Creative Works

Trickle-Bed Reactors Are Widely Used in Industrial High Pressure Operations (Up to 30 MPa). the Knowledge of Catalyst Wetting Efficiency as a Function of Operating Conditions is Needed for Relating Laboratory and Pilot Scale Reactor Data to Large Scale Reactor Operation. the Available Predictions of the Wetting Efficiency Rest on Data Collected at Atmospheric Pressure. in This Study a Phenomenological Analysis Has Been Developed to Relate the Wetting Efficiency with Operating Conditions Such as Reactor Pressure, Gas and Liquid Flow Rate. Experimental Data for the Wetting Efficiency at High Pressure Have Been Obtained Via a Tracer Technique. the Data Support …

An Efficient Multicomputer Algorithm For The Solution Of Chemical Process Flowsheeting Equations, Fikret Ercal, Neil L. Book, S. Pait, J. J. Fielding

Computer Science Faculty Research & Creative Works

This paper presents a parallel solution method of large sparse systems of linear equations arising in the context of a chemical process flowsheeting application on a message passing multicomputer. To maximize the performance, the algorithm uses a novel matrix decomposition and solution method, called parallel two-phased LU decomposition, which schedules the concurrent tasks in a maximally overlapping manner, and at the same time, tries to minimize the interprocessor data dependencies and obtain optimal load balancing. The forward elimination step is performed concurrently with the parallel two-phased LU decomposition step and backward substitution is parallelized in a piecewise manner. Implementation results …

1995 Directory Of Indiana State, County, City And Town Officials Responsible For Road And Street Work, Herpicc

Indiana Local Technical Assistance Program (LTAP) Directory

Contact information for agency officials and employees responsible for Indiana’s local road infrastructure.

Theoretically Optimal Duty Cycles For Chest And Abdominal Compression During External Cardiopulmonary Resuscitation, Charles F. Babbs, Keir Thelander

Weldon School of Biomedical Engineering Faculty Publications

Objective: To use an electronic model of human circulation to compare the hemodynamic effects of different durations of chest compression during external CPR, both with, and without interposed abdominal compression (IAC). Methods: An electrical analog model of human circulation was studied on digital computer workstations using SPICE, a general-purpose circuit simulation program. In the model the heart and blood vessels were represented as resistive-capacitive networks, pressures as voltages, blood flow as electric current, blood inertia as inductance, and cardiac and venous valves as diodes. External pressurization of the heart and great vessels, as would occur in IAC-CPR, was simulated by …

On The Carrier Mobility In Forward-Biased Semiconductor Barriers, Mark S. Lundstrom, Shin'ichi Tanaka

Department of Electrical and Computer Engineering Faculty Publications

A simple one-speed solution to the Boltzmann equation is used to evaluate the mobility and diffusion coefficient for carriers in forward-biased semiconductor barriers. The analysis shows that although the average kinetic energy of carriers remains near thermal equilibrium, the mobility and diffusion coefficient are strongly reduced by the built-in field. Conventional macroscopic transport equations, which treat the carrier mobility and diffusion coefficient as single valued functions of the kinetic energy will improperly treat transport in forward-biased barriers. The results are important for the careful analysis of metal–semiconductor and heterojunction diodes.