Engineering Commons^™

Test 1691: John Deere 8400 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1693: Agco Allis 9455 Diesel 32-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1690: John Deere 8300 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1695: White 6144 Diesel 32-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1694: White 6124 Diesel 32-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1697: Agco Allis 9635 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1699: Agco Allis 9675 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1701: Ford 3930 8x2 Diesel 8-Speed (Chassis S/N Bd81400 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1702: Ford 3930 8x8 Diesel 8-Speed (Chassis S/N Be81400 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1703: Ford 4630 16x8 Diesel 16-Speed (Chassis S/N Bd81699 And Higher), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1704: Ford 5030 16x8 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nebraska Summary: S197 Massey Ferguson 8120, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Semiempirical Model For The Electrical Properties Of La1-Xcaxcoo3, S. R. Sehlin, Harlan U. Anderson, Don M. Sparlin

Materials Science and Engineering Faculty Research & Creative Works

A semiempirical model of the Seebeck coefficient for a small polaron hopping conductor is presented. The population of small polarons is allowed to change as a function of temperature via the mechanism of charge disproportionation. The energy required for polaron formation by the disproportionation mechanism is modeled as screened by a Coulomb interaction with nearby small polarons. The charge carrier site occupancies generated by the model are used to successfully predict the electrical conductivity and Seebeck coefficient for compositions in the La1-xCaxCoO3 system. Cobalt ion valence populations predicted by the model are used to calculate effective paramagnetic moments for LaCoO3, …

Structure And Electrical Properties Of La1-Xsrxco1-Yfeyo3. Part 1. The System La0.8sr0.2co1-Yfeyo3, L. W. Tai, M. M. Nasrallah, Harlan U. Anderson, Don M. Sparlin, S. R. Sehlin

Materials Science and Engineering Faculty Research & Creative Works

Crystal structure, thermal expansion, thermogravimetry, thermoelectricity, and electrical conductivity of compositions in the system La0.8Sr0.2Co1-yFeyO3 with 0 ≤ y ≤ 1 were studied as function of Co Fe ratio and temperature, in air. The electrical conduction mechanism is attributed to the adiabatic-hopping of p-type small polarons. At high temperatures, oxygen deficiency causes lattice expansion and a reduction in electrical conductivity. The observed temperature dependence of the Seebeck coefficient is attributed to changes in carrier concentration caused by a thermally excited charge disproportionation of Co3+ ions and by the ionic compensation of induced oxygen vacancies. The measured electrical conductivity and Seebeck …

Structure And Electrical Properties Of La1 - Xsrxco1 - Yfeyo3. Part 2. The System La1 - Xsrxco0.2fe0.8o3, L. W. Tai, M. M. Nasrallah, Harlan U. Anderson, Don M. Sparlin, S. R. Sehlin

Materials Science and Engineering Faculty Research & Creative Works

Crystal structure, thermal expansion, oxygen stoichiometry, thermoelectricity, and electrical conductivity of compositions in the system La1 - xSrxCo0.2Fe0.8O3 with 0 ≤ x ≤ 0.6 were studied as function of temperature and Sr content, in air. The solubility of Sr in the sintered perovskite-type oxide (ABO3) was limited to x ≤ 0.4. The observed p-type electrical conduction appeared to occur via a small-polaron hopping mechanism. The thermally induced oxygen loss caused a lattice expansion plus decreases in both the carrier concentration and the carrier mobility. A semi-empirical model was developed which takes into account the thermally activated disproportionation of Co3+ ions …

Iron Phosphate Glasses As A Potential Nuclear Waste Disposal Medium, Melissa G. Mesko

Masters Theses

”Phosphate glasses containing large amounts of Fe₂O₃ (up to 43wt%) were studied to determine their potential suitability as nuclear waste disposal glasses for high level radioactive wastes containing large concentrations of iron oxide, phosphate, and fluoride compounds. Glass formation and chemical durability was the prime focus of this study, while properties such as density, thermal expansion, dilatometric softening temperature, and devitrification temperature were examined as well. It was found that large amounts of simulated nuclear waste material (up to 44.4wt% Cs₂O or 37.5wt% SrO) could be incorporated into the base iron phosphate glass while retaining …

Effects Of Specimen Size Reduction On The Transition Curve Of The Charpy V-Notch Impact Test, Lonnie Eugene Schubert

Masters Theses

"This study was undertaken to correlate the impact properties of ASTM standard full size Charpy V-notch impact specimens to the impact properties of subsize specimens. An ASTM A533-B quenched and tempered plate steel was examined. The fine grained martensitic material had a coarse prior austenite grain size, which resulted in a low upper shelf energy for this material. Three sizes of specimens were included. Specimens were irradiated in the TRIGA Reactor Facility operated by the U. S. Geological Survey in Denver, Colorado, to 1 x 10¹⁹ n/cm² (E > 1 MeV) at 150°C (302°F). Unirradiated and irradiated specimens were …

A Neural Network Thrust Force Controller To Minimize Delamination During Drilling In Graphite Epoxy Laminates, Robert B. Stone

Masters Theses

"Delamination is a well-recognized problem associated with drilling in fiber-reinforced composite materials (FRCM). The most noted problems occur as the drill enters and exits the FRCM. Since drilling is often a final operation during assembly, any defects introduced in parts by drilling represent an expensive loss. Studies based on linear elastic fracture mechanics theory have proposed critical thrust forces in the various drilling regions that will prevent crack growth or delamination. Using these critical thrust force curves as a guide, a thrust force controller was developed to minimize the delamination while drilling in graphite epoxy laminates. A neural network control …

Nonlinear Robust Control Of A Series Dc Motor Utilizing The Recursive Design Approach, Michael J. Burridge

Retrospective Theses and Dissertations

In this thesis, the investigation of asymptotic stability of the series DC motor with unknown load-torque and unknown armature inductance is considered. The control technique of recursive, or backstepping, design is employed. Three cases are considered. In the first case, the system is assumed to be perfectly known. In the second case, the load torque is assumed to be unknown and a proportional-integral controller is developed to compensate for this unknown quantity. In the final case, it is assumed that two system parameters, load torque and armature inductance, are not known exactly, but vary from expected nominal values within a …

Ac Impedance Studies On Metal Hydride Electrodes, Wenlin Zhang, M. P. Sridhar Kumar, Supramaniam Srinivasan, Harry J. Ploehn

Faculty Publications

The metal hydride (MH_x) electrode is the negative electrode in one of the most advanced secondary batteries (i.e.,nickel/metal hydride). The objective of this study is to obtain insight on the mechanism of the hydriding/dehydridingreaction in the battery by using the electrochemical impedance spectroscopy (EIS) technique. An equivalent circuit for the MH_x electrode reaction is proposed. The rate capability of charge and discharge of the MH_x electrode is determined by thekinetics of the charge-transfer reaction at the alloy surface, which is mainly represented by the EIS responses in the lowfrequency region. Transient and pseudo-steady-state analyses …

Supralinear Photoconductivity Of Copper Doped Semi-Insulating Gallium Arsenide, K. H. Schoenbach, R. P. Joshi, F. Peterkin, R. L. Druce

Bioelectrics Publications

We report on the intensity dependent supralinear photoconductivity in GaAs:Si:Cu material. The results of our measurements show that the effective carrier lifetime can change over two orders of magnitude with variations in the intensity of the optical excitation. A threshold intensity level has been observed and can be related to the occupancy of the deep copper level. Numerical simulations have also been carried out to analyze the trapping dynamics. The intensity dependent lifetimes obtained from the simulations match the experimental data very well. Finally, based on the nonlinear intensity dependence of the effective lifetimes, a possible low‐energy phototransistor application for …

Towards A More Hands-On, Design-Oriented Course On Mechanisms, Burford Furman

Faculty Research, Scholarly, and Creative Activity

No abstract provided.

Identification Of Success Factors In The Implementation Of Computer-Integrated Manufacturing, Dean Harold Jensen

Dissertations and Theses @ UNI

The review of recent literature showed a clear trend within the manufacturing sector toward the integration of design and production activities through increased application of the computer. The competitive advantages of computer integration were reported, as well as increased risk due to the amount of time and capital expended in system implementation. The identification of computer integrated manufacturing (CIM) success factors may reduce this risk.

Prior efforts to identify success factors for other areas of endeavor showed that success factors tended to vary with the four project phases, but were stable over time within a particular phase. More recently, empirical …

On The Use Of Students For Developing Engineering Laboratories, Bopaya Bidanda, Richard E. Billo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper describes a unique and innovative approach that solved the dual problem of starting up a new engineering instructional laboratory in a timely manner, and for teaching engineering students advanced skills in Automatic Data Collection. Students enrolled in a special pilot course were used to develop and startup an Automatic Data Collection laboratory. These students were assigned individual Automatic Data Collection technologies of interest and given total responsibility for the successful startup of the laboratory. The organization and structure of the course modeled the typical team oriented project development efforts in industry. Feedback from students showed the course to …

Thermal Contact Conductance Of Ceramic Substrate Junctions, K. C. Chung, H. K. Benson, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Improved Finite Element Modeling Of The Turbofan Engine Inlet Radiation Problem, I. Danda Roy, Walter Eversman

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Improvements have been made in the finite element model of the acoustic radiated field from a turbofan engine inlet in the presence of a mean flow. The problem of acoustic radiation from a turbofan engine inlet is difficult to model numerically because of the large domain and high frequencies involved. A numerical model with conventional finite elements in the near field and wave envelope elements in the far field has been constructed. By employing an irrotational mean flow assumption, both the mean flow and the acoustic perturbation problem have been posed in an axisymmetric formulation in terms of the velocity …

Maximum-Likelihood Time Delay Estimation: A New Perspective, John A. Stuller, Nancy Hubing

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Introduces a New Realization for Maximum Likelihood Time-Delay Estimation. the New Realization Illuminatesthe Relationships between Maximum Likelihood Time Delay Estimation and Other Methods. We Obtain the Result by Deriving the Likelihood Function using a Fundamental Method that, Surprisingly, Appears to Be New to The field of Array Processing. This Method is a Natural Complement to the Karhunen-Loeve Transform Having Vector Eigenfunctions and Scalar Eigenvalues, and It Generalizes to M Measurements, M 2 2. Moreover, It Can Be Applied to Other Multichannel estimation problems.

A Two-Dimensional Image Model Based On Occlusion And Maximum Entropy, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Provides New Insights into the Formation of Two-Dimensional Image Autocorrelation Functions. We Model an Image as a Maximum-Entropy Composition of Individual Occluding Object Images that Have Random Positions, Shapes and Intensities. We Derive the Autocorrelation Function of This Image Model, Give an Example, and Comment on the Reasonableness of the Frequently-Made Assumptions of Autocovariance Separability and Isotropy.

Least Squares Order-Recursive Lattice Smoothers, Jenq Tay Yuan, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

Conventional Least Squares Order-Recursive Lattice (LSORL) Filters Use Present and Past Data Values to Estimate the Present Value of a Signal. This Paper Introduces LSORL Smoothers Which Use Past, Present and Future Data for that Purpose. Except for an overall Delay Needed for Physical Realization, LSORL Smoothers Can Substantially Outperform LSORL Filters While Retaining All the Advantages of an Order-Recursive Structure. © 1995 IEEE

The Performance Of Reed-Solomon Codes On A Bursty-Noise Channel, William J. Ebel, William H. Tranter

Electrical and Computer Engineering Faculty Research & Creative Works

The performance of a Reed-Solomon coded binary communication system on a bursty-noise channel is considered. Bursty noise is defined to be background Gaussian noise plus burst noise, where burst noise is defined to be a series of finite-duration Gaussian-noise pulses with fixed duration and Poisson occurrence times. Using the noise model, along with ideal symbol interleaving, decoded bit-error probability bounds are derived for the case where the noise bursts are long with respect to the channel symbol rate. Specific performance results are presented for the (31,15,8) Reed-Solomon Joint Tactical Distribution System (JTIDS) code with a Binary Phase Shift Keyed (BPSK) …