Investigation Of Humidity And Temperature Response Of A Silica Gel Coated Microfiber Coupler, Yuliya Semenova, Gerald Farrell, Dejun Liu

Conference Papers

The humidity and temperature responses of a microfiber coupler (MFC) coated with silica gel are investigated. Two MFC structures with different waist diameters of 2.5 and 3.5 μm were fabricated by fusing and tapering two single-mode fibers using a microheater brushing technique. The influences of the coating thickness and tapered waist diameter on the sensing performance are analyzed. For the proposed sensor with a waist diameter of 2.5 μm and 8-layers thick coating, the change in the relative humidity (RH) results in an exponential blueshift with a maximum sensitivity of 1.6 nm/% RH in the range from 70 to 86% …

Eliminating Electromechanical Instability In Dielectric Elastomers By Employing Pre-Stretch, Liang Jiang, Tony Betts, David Kennedy, Stephen Jerrams

Articles

Electromechanical instability (EMI) is one of most common failure modes for dielectric elastomers (DEs). It has been reported that pre-stretching a DE sample can suppress EMI due to strain stiffening taking place for larger strains and a higher elastic modulus are achieved at high stretch ratios when a voltage is applied to the material. In this work, the influence of equi-biaxial stretch on DE secant modulus was studied using VHB 4910 and silicone rubber (SR) composites containing barium titanate (BaTiO3, BT) particles and also dopamine coated BT (DP-BT) particles. The investigation of equi-biaxial deformation and EMI failure for VHB 4910 …

Corrigendum To “Energy Savings Across Eu Domestic Building Stock By Optimizing Hydraulic Distribution In Domestic Space Heating Systems”, Ciara Ahern, Brian Norton

Articles

No abstract.

Synthesis And Doping Feasibility Of Composite-Hydroxide-Mediated Approach For The Cu1-Xznxo Nanomaterials, Tauseef Shahid, Muhammad Arfan, Waqas Ahmad, Tayyaba Bibi, Taj Muhammad Khan

Articles

In this article, we report feasibility of composite hydroxide-mediated (CHM) approach for the synthesis and doping of Cu1-xZnxO (x=0%, 3%, 6% and 9%) nanomaterial. The proposed method offers a low cost, low temperature and environmentally friendly approach to preparing doped nanomaterials in a feasible and cost- effective route. Further, we investigate the effect of incorporated Zn +2 on the properties of produced Cu (II) O nanostructures. The X-ray diffraction analysis confirms formation of the single-phase monoclinic Cu (II) O and incorporation of Zn at the Cu-lattice sites. The crystalline structure is improved and the average grain size has increased from …

Unique Characterization Of Materials With Memory, John Murrough Golden

Articles

In general, materials with linear memory constitutive relations are characterized by a relaxation function. This leads to a situation where the free energy for most materials with memory is not unique. There is a convex set of free energy functionals with a minimum and a maximum element. An alternative procedure is proposed which characterizes a material by the kernel of the rate of dissipation functional. Using some recent results, we find that a unique free energy and relaxation function may then be deduced. An example is given for discrete spectrum materials. Also, the new results are used to show that …

Sol-Gel Silica Coated Optical Fiber Sensor For Ammonia Gas Detection, Dejun Liu, Arun Mallik, Wei Han, Qiang Wu

Conference papers

A high sensitivity ammonia gas sensor based on a tapered small core single-mode fiber (SCSMF) structure for measurement of ammonia gas concentration is reported. The proposed tapered SCSMF fiber structure has a waist diameter of 13.5 μm and it is fabricated using a customized microheater brushing technique. The silica based material prepared by sol-gel method is used as a coating applied to the surface of tapered fiber structures. Experimental results show that sensor is very sensitive to ammonia. The best measurement resolution of the ammonia concentration is estimated to be 16 ppb for gas concentrations of 0.5 ppm to 2.5 …

Specification Development For Cold In-Situ Recycling Of Asphalt, Amir Tabakovic, Ciaran Mcnally, Eanna Fallon

Research and Innovation - Articles

In-situ cold recycling provides a valuable means to reduce the environmental impact of road construction. The reduced energy requirements relative to traditional hot mix recycling can lead to significant reductions in cost and associated CO₂ emissions. Worldwide, in-situ cold recycling has been found to be particularly useful in the rehabilitation of rural roads where site locations are far from asphalt plants. However, practical issues remain due to the evolving nature of cold bituminous materials. Unlike hot-mix asphalts which gain strength quickly as they cool, cold-mix bituminous materials gain strength slowly over time. This is particularly an issue in countries …

Oxygen Transport, Shear Stress, And Metabolism In Perfused Hepatocyte-Seeded Scaffolds With Radial Pore Architecture: Experimental And Computational Analyses, Chijioke Mbanu

Wayne State University Dissertations

Several modalities have been proposed as treatments or temporary stop-gap for patients suffering from liver failure until a suitable organ is available. However there is still an urgent need for an off-the-shelf device that can accommodate clinically relevant cell numbers, be cultured at physiological oxygen tensions and, can be fully integrated into and heal the injured hepatic space. In this study we investigated the effects that convective and direct oxygenation had on hepatocyte functionality, morphology and viability while cultured in bulk 3D chitosan scaffolds and perfusion bioreactor systems. Cylindrical chitosan scaffolds with radial directed pore structures were fabricated by a …

Computational Modeling Of High-Performance Nickel-Metal Hydride Battery Materials, Diana Felicia Wong

Wayne State University Dissertations

With 10 million hybrid electric vehicles on the road worldwide powered primarily by nickel-metal hydride (NiMH) batteries, research into this battery chemistry will improve the hybrid vehicle driving experience, extending electric-only driving ranges while reducing emissions and using less gasoline. The transfer, storage and transport of protons and electrons depend strongly on the structural and electrical features of the active material, including multiple phases, defects, and structural and compositional disorder. The contributions of such subtle defects and the difference with the bulk structure can be difficult to discern experimentally. Ab initio calculations such as the ones based on density functional …

The Relationship Of Corporate Financial Performance And Innovation Among Manufacturing Industries, Charlaine T. Chong, Samantha R. Chua, Ma. Catrina S. Dy, Antonio Miguel E. Villavicencio

Angelo King Institute for Economic and Business Studies (AKI)

Innovation is becoming a critical determinant of the survival and advancement of firms. Despite this realization, there is a dearth of literature that tackles the subject matter and its specific role in corporate settings remains vague. Using corporate data on East and Southeast Asian manufacturing firms from 2008 to 2013, this study aims to identify the impact of corporate financial performance on research and development (R&D) expenditure as a measure of innovation. On the whole, the researchers utilized random effects (REM) and fixed effects (FEM) models to establish the relationship between R&D and corporate performance. The researchers, then, identified the …

Impacts On One-Off Housing Arising From Amended Building Control Regulations In Ireland, Myles Keaveney, Kieran Compton

Conference papers

Single rural housing is very common in the Irish countryside. The Irish Central Statistics Office reported that one-off housing represented over a quarter of the total number of households in 2011. One-off houses are defined as occupied detached houses with individual septic tank wastewater treatment systems in rural areas (which include towns with a population of 1,500 or less).

The purpose of this study is to determine the increased cost to the consumer resulting from the introduction of the new Building Control (Amendment) Regulations 2014. In order to achieve the objective, a detailed description of past and current building control …

Main Contractor Selection On Construction Projects When Adapting An Integrated Project Delivery Procurement Strategy Within An Irish Context., Fiacra Mcdonnell

Other Resources

The Irish construction industry has experienced turbulent years over the last decade from an economic viewpoint. The industry has tended to be conservative in nature and slow to embrace change. However international influences have exposed Irish construction professionals to new more efficient systems and technologies, which although slow to take hold have started to gain traction within certain sectors of the industry. This study has focussed on the innovative procurement route known as Integrated Project Delivery (IPD), and its facilitator; Building Information Modelling (BIM). The overall aim of this study was to investigate whether Integrated Project Delivery was a viable …

A Coplanar Vivaldi Antenna With Integrated Filter For Ka-Band, Kansheng Yang, Abraham Loutridis, Xiulong Bao, Patrick Mcevoy, Max Ammann

Conference Papers

A new design approach of a dual-stub coplanar Vivaldi antenna with integrated filter is presented. The dual-stub excites coupling between a parasitic elliptical element and tapered slots. The dimensions of the parasitic element are studied and optimized for wide beamwidth. The band pass filter is used for sub harmonic suppression and pattern shaping.

Laboratory Evaluation Of A Real-Time Coaxial Cable Casing Imager For Wellbore Integrity Monitoring, Yurong Li, Runar Nygaard, Baokai Cheng, Wenge Zhu, Hai Xiao

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Leakage is one of the major concerns in a geological carbon sequestration project due to the adverse environmental consequences. The main leakage risk of CO₂ through a thick, low permeable cap rock is identified to be along wells, especially in sedimentary basins that have a history of oil and gas exploration and production. To pursue a robust and cost-effective real-time monitoring technology for CO₂ leakage risk detection along the wellbore, a permanently downhole deployed coaxial cable casing imaging system is developed and tested for various deformation modes in laboratory in this paper. The casing imager consists of a …

Automated Generation And Visualization Of Initial Construction Schedules From Building Information Models, Yibrah Weldemihret Weldu

LSU Doctoral Dissertations

Recent advances in digital technology have had a significant influence on the quality and speed of sharing and communicating project information in the architecture, engineering, and construction (AEC) industry. The process of acquiring the design intent in order to develop and communicate project schedules, as critical components of project delivery, have similarly been benefitting from such progress. With the relatively recent techniques of Building Information Modeling (BIM) and its capability to integrate the facility design with its construction schedule, meaningul strides have been made in improving the information flow and eventually visualizing the final schedule in 4D. However, the need …

Small Scale-Wind Power Dispatchable Energy Source Modeling, Jordan J. Cannon, David Moore, Stephen Eason, Adel El-Shahat

Electrical & Computer Engineering: Faculty Publications

Due to the importance of Wind energy as an intermittent renewable resource in Micro-Grids applications; this paper is proposed. So this research proposal seeks to model and analyze components of a wind turbine generator (WTG) system to store energy and supply loads with the stored energy. Focus is placed on the storage of energy into a lead acid battery and using the battery with the inverter as a dispatchable energy source. The storage device and inverter acts as a steam power plant generator. The small-scale system consists of wind turbine, wind generator, loads, dc-dc converter, ac-dc inverter, controller and battery. …

Modeling Mental Workload Via Rule-Based Expert System: A Comparison With Nasa-Tlx & Workload Profile, Lucas Rizzo, Sarah Jane Delany, Pierpaolo Dondio, Luca Longo

Conference papers

In the last few decades several fields have made use of the construct of human mental workload (MWL) for system and task design as well as for assessing human performance. Despite this interest, MWL remains a nebulous concept with multiple definitions and measurement techniques. State-of-the-art models of MWL are usually ad-hoc, considering different pools of pieces of evidence aggregated with different inference strategies. In this paper the aim is to deploy a rule-based expert system as a more structured approach to model and infer MWL. This expert system is built upon a knowledge-base of an expert and transates into computable …

Mathematical Scaling And Statistical Modeling Of Geopressured Geothermal Reservoirs, Esmail Ansari

LSU Doctoral Dissertations

The interest for developing geopressured-geothermal reservoirs along the US Gulf Coast is increasing for securing energy needs and reducing global warming. Identifying the most attractive candidate reservoirs for geothermal energy production requires quick and simple models. Analytical models are not always available and simulating each case individually is expensive. The use of scaling and statistical modeling is one approach to translate the output of a simulator into quick models with general applicability at all scales. The developed models can quickly estimate temperature and thermal energy recovery from the geopressured-geothermal reservoirs. These models can screen large databases of reservoirs to select …

Effect Of Powder Particle Size On The Fabrication Of Ti-6al-4v Using Laser Metal Deposition From Elemental Powder Mixture, Xueyang Chen, Lei Yan, Wei Li, Frank W. Liou, Joseph William Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct LMD (laser metal deposition) was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM (scanning electron microscopy), OM (optical microscopy) and EDS (energy dispersive spectroscopy) were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the …

Antibody Targeting Facilitates Effective Intratumoral Sirna Nanoparticle Delivery To Her2-Overexpressing Cancer Cells, Maria C. Palanca-Wessels, Garrett Booth, Anthony J. Convertine, Brittany B. Lundy, Geoffrey Y. Berguig, Michael F. Press, Patrick S. Stayton, Oliver W. Press

Materials Science and Engineering Faculty Research & Creative Works

The therapeutic potential of RNA interference (RNAi) has been limited by inefficient delivery of short interfering RNA (siRNA). Tumor-specific recognition can be effectively achieved by antibodies directed against highly expressed cancer cell surface receptors. We investigated the utility of linking an internalizing streptavidinconjugated HER2 antibody to an endosome-disruptive biotinylated polymeric nanocarrier to improve the functional cytoplasmic delivery of siRNA in breast and ovarian cancer cells in vitro and in an intraperitoneal ovarian cancer xenograft model in vivo, yielding an 80% reduction of target mRNA and protein levels with sustained repression for at least 96 hours. RNAi-mediated site specific cleavage …

Analysis Of The Developing States In The Mena Region Seeking Civilian Nuclear Energy, With A Primary Focus On The Kingdom Of Saudi Arabia (Ksa) And The United Arab Emirates (Uae), Thaqal Alhuzaymi, Ayodeji Babatunde Alajo

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

The comprehensive analysis presented here attempts to ana­lyze “newcomer” states in the Middle East and North Africa (MENA), primarily the Kingdom of Saudi Arabia (KSA) and Unit­ed Arab Emirates (UAE), seeking to implement civilian nuclear energy according to their political and economic situations. By investigating their motivations and funding resources for fu­ture nuclear projects, this analysis provides guidance for these states in terms of their nuclear infrastructure and nonprolifera­tion. The overall approach of this analysis relies on the factors for the success of civilian nuclear energy programs identified in experiential studies conducted since the Atoms for Peace speech in 1953.This …

Autonomous Navigation With Obstacle Avoidance For Unmanned Aircraft Systems Using Milp, James A. Devens

Theses and Dissertations

Autonomous coordination among multiple aerial vehicles to ensure a collision free airspace is a critical aspect of today’s airspace. With the rise of Unmanned Aerial Vehicles (UAVs) in the military and commercial sectors, obstacle avoidance in a densely populated airspace is necessary. This thesis investigates finding optimal or near-optimal trajectories in real-time for aircraft in complex airspaces containing a large number of obstacles. The solution for the trajectories is described as a linear program subject to mixed integer constraints, known as a Mixed Integer Linear Program (MILP). The resulting MILP problem is solved in real time using a well-known, public …

Pattern Recognition In Class Imbalanced Datasets, Nahian A. Siddique

Theses and Dissertations

Class imbalanced datasets constitute a significant portion of the machine learning problems of interest, where recog­nizing the ‘rare class’ is the primary objective for most applications. Traditional linear machine learning algorithms are often not effective in recognizing the rare class. In this research work, a specifically optimized feed-forward artificial neural network (ANN) is proposed and developed to train from moderate to highly imbalanced datasets.

The proposed methodology deals with the difficulty in classification task in multiple stages—by optimizing the training dataset, modifying kernel function to generate the gram matrix and optimizing the NN structure. First, the training dataset is extracted …

Structure And Corrosion Behavior Of Sputter Deposited Ce-Al-O Coating On Al 2024-T3 Alloy Substrates, Yuanyuan Liu, Jiamu Huang, James B. Claypool, Matthew J. O'Keefe

Materials Science and Engineering Faculty Research & Creative Works

Deposition of Ce-Al-O coatings on Al 2024-T3 alloy substrates was conducted by magnetron co-sputtering of CeO₂ and Al targets. The incorporation of Al into the CeO₂ film resulted in an amorphous or nanocrystalline structure with binding energy states different from Al, Al₂O₃, and CeO₂. Electrochemical measurements indicated that the amorphous or nanocrystalline Ce-Al-O coating increased the corrosion resistance of bare Al 2024-T3 substrates by more than three orders of magnitude and exhibited a very different cathodic and anodic protective mechanism compared to Al and CeO₂ coated and as-polished Al 2024-T3 samples. …

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Evidential Reasoning For Forensic Readiness, Yi-Ching Liao, Hanno Langweg

Journal of Digital Forensics, Security and Law

To learn from the past, we analyse 1,088 "computer as a target" judgements for evidential reasoning by extracting four case elements: decision, intent, fact, and evidence. Analysing the decision element is essential for studying the scale of sentence severity for cross-jurisdictional comparisons. Examining the intent element can facilitate future risk assessment. Analysing the fact element can enhance an organization's capability of analysing criminal activities for future offender profiling. Examining the evidence used against a defendant from previous judgements can facilitate the preparation of evidence for upcoming legal disclosure. Follow the concepts of argumentation diagrams, we develop an automatic judgement summarizing …

In-The-Wild Residual Data Research And Privacy, William B. Glisson, Tim Storer, Andrew Blyth, George Grispos, Matt Campbell

Journal of Digital Forensics, Security and Law

As the world becomes increasingly dependent on technology, researchers in both industry and academia endeavor to understand how technology is used, the impact it has on everyday life, the artifact life-cycle and overall integrations of digital information. In doing so, researchers are increasingly gathering 'real-world' or 'in-the-wild' residual data, obtained from a variety of sources, without the explicit consent of the original owners. This data gathering raises significant concerns regarding privacy, ethics and legislation, as well as practical considerations concerning investigator training, data storage, overall security and data disposal. This research surveys recent studies of residual data gathered in-the-wild and …

Low Budget Forensic Drive Imaging Using Arm Based Single Board Computers, Eric Olson, Narasimha Shashidhar

Journal of Digital Forensics, Security and Law

Traditional forensic analysis of hard disks and external media typically involves a powered down machine and “dead analysis” of these devices. Forensic acquisition of hard drives and external media has traditionally been by one of several means: standalone forensic duplicator; using a hardware write-blocker or dock attached to a laptop, computer, workstation, etc., forensic operating systems that live boot from a USB, CD/DVD or virtual machines with preinstalled operating systems. Standalone forensics acquisition and imaging devices generally cost thousands of dollars. In this paper, we propose the use of single board computers as forensic imaging devices. Single board computers can …

Digital Forensics In Law Enforcement: A Needs Based Analysis Of Indiana Agencies, Teri A. Cummins Flory

Journal of Digital Forensics, Security and Law

Cyber crime is a growing problem, with the impact to society increasing exponentially, but the ability of local law enforcement agencies to investigate and successfully prosecute criminals for these crimes is unclear. Many national needs assessments have previously been conducted, and all indicated that state and local law enforcement did not have the training, tools, or staff to effectively conduct digital investigations, but very few have been completed recently. This study provided a current and localized assessment of the ability of Indiana law enforcement agencies to effectively investigate crimes involving digital evidence, the availability of training for both law enforcement …

Table Of Contents

Journal of Digital Forensics, Security and Law

No abstract provided.