Civil Engineering Commons^™

Production Of Low-Cost Self-Consolidating Concrete (Scc) Using Manufactured Aggregates, Rabab Raydan, Farah Chamseddine, Ali Jahami, Oussama Baalbaki, Jamal Khatib, Adel Elkordi

BAU Journal - Science and Technology

Limitations to the sources of aggregates and the unavailability of sand is becoming a problematic issue for concrete production. A novel technology of manufactured aggregates can produce well graded round aggregates that can substitute natural aggregates while maintaining the same characteristics needed and preserving the resources. Self-Consolidating Concrete (SCC) using manufactured aggregates is assessed in this experimental work to understand the variability of workability properties and mechanical properties with the changes in w/c ratio and percentages of Coarse Aggregates and Manufactured Sand to Natural Sand in order to choose the best mixture that satisfies an adequate overall performance. Targeting compressive …

Passive Radiative Cooling By Spectrally Selective Nanoparticles In Thick Film Nanocomposites, David Allen Young

USF Tampa Graduate Theses and Dissertations

Passive cooling of buildings is a benefit to society since no energy input is required for space cooling which reduces electricity consumption, fossil fuel burning, and greenhouse gas emissions. When a passive cooling technology radiates heat from the earth through the atmospheric windows to space higher levels of cooling power are possible -- this phenomenon is classified as passive “radiative” cooling. Spectrally selective surface coatings provide radiative cooling to lower surface temperatures by reflecting most solar radiation, while emitting infrared radiation at wavelengths between 8-13 μm through the primary atmospheric window to the cold of space. Multiple applications of radiative …

Unconventional Water Resources: Global Opportunities And Challenges, Zahra Karimidastenaei, Tamara Avellán, Mojtaba Sadegh, Bjørn Kløve, Ali Torabi Haghighi

Civil Engineering Faculty Publications and Presentations

Water is of central importance for reaching the Sustainable Development Goals (SDGs) of the United Nations. With predictions of dire global water scarcity, attention is turning to resources that are considered to be unconventional, and hence called Unconventional Water Resources (UWRs). These are considered as supplementary water resources that need specialized processes to be used as water supply. The literature encompasses a vast number of studies on various UWRs and their usefulness in certain environmental and/or socio-economic contexts. However, a recent, all-encompassing article that brings the collective knowledge on UWRs together is missing. Considering the increasing importance of UWRs in …

Evaluation Of Aluminum Dissolution, Current Density, And Pitting Patterns During Electrocoagulation, Monica Castro Carias

USF Tampa Graduate Theses and Dissertations

Electrocoagulation (EC) is a sustainable water treatment process involving the generation of coagulants on-site through the application of a voltage on metal (usually aluminum or iron alloys). The factors that impact EC system performance have been well researched, however further research is needed on the factors that impact anodic dissolution of aluminum electrodes, especially when the technology is transferred to full-scale applications. Electrode fouling is one of the factors that can impact dissolution of the anode during EC due to the formation of a protective oxide/hydroxide layer on the electrode surface. Previous studies have addressed electrode fouling by reversing polarity, …

Degradation Performance Modeling And Optimal Maintenance Planning Of Deteriorating Critical Infrastructures, Hung Q. Nguyen

USF Tampa Graduate Theses and Dissertations

Serving as the backbone of the nation’s economy, a large and growing number of deteriorating critical infrastructures, such as transportation and water infrastructures, are underperforming, aging, becoming structurally deficient, and must be repaired or replaced. Due to the influence of a variety of factors (e.g., material structure, design, operation, and environmental conditions) at different phases of lifecycle and the costly data acquisition process, field degradation of deteriorating infrastructures is highly uncertain with limited degradation data. The co-location and spatial proximity between many infrastructures, such as road and water infrastructures, further makes them physically and operationally interdependent. The sheer deterioration of …

Simulating Flood Control In Progress Village, Florida Using Storm Water Management Model (Swmm), Azize Minaz

USF Tampa Graduate Theses and Dissertations

Flooding is a natural event caused by heavy rains, melting snow, high tides, and anthropogenic impacts such as channel clogging, improper land use, and deforestation. In this study, the strategies for controlling flooding seek to establish flood prevention systems by implementing grey infrastructure and green infrastructure practices. The main objective of this thesis is to analyze the study area, Progress Village Neighborhood in Delaney Creek Watershed, regarding flood risk and flood mitigation techniques. The analysis was performed using EPA SWMM 5.1 and Arcmap 10.7.1. The study used design storms,10-years 24 hours and 25-years 24 hours, to analyze flood risk in …

Impedance Analysis Of Anodized Aluminum And Structural Bridge Tendons, Justin Silnutzer

USF Tampa Graduate Theses and Dissertations

This is a two-part thesis with the overall investigation technique being electrochemical impedance spectroscopy (EIS). In the first part, EIS is used to estimate the layer thickness of anodized aluminum oxide. This required the development of an appropriate electrical circuit model; that with parameters that correspond to physical properties of the oxide. In this work, it was found that for thicker oxides of which the outer porous layer is greater than 12 microns, impedance may be used to estimate the outer layer thickness. However, further research is required to understand the role of outer porous layer structure on the impedance …

An Improved Polynomial Chaos Expansion Based Response Surface Method And Its Applications On Frame And Spring Engineering Based Structures, Mhd A. Hafez

ETD Archive

In engineering fields, computational models provide a tool that can simulate a real world response and enhance our understanding of physical phenomenas. However, such models are often computationally expensive with multiple sources of uncertainty related to the model’s input/assumptions. For example, the literature indicates that ligament’s material properties and its insertion site locations have a significant effect on the performance of knee joint models, which makes addressing uncertainty related to them a crucial step to make the computational model more representative of reality. However, previous sensitivity studies were limited due to the computational expense of the models. The high computational …

Effects Of Slurry Type On Drilled Shaft Strength, Cesar Quesada Garcia

USF Tampa Graduate Theses and Dissertations

The main objective of this research is to identify how the strength of drilled shafts is affected by the use of various types of drill slurry. When concrete is placed in drilled shafts it flows out radially and a laitance interface forms creating a crease on the backside of the reinforcement cage due to the laitance trapped in concrete flowing around the rebar. This can cause concrete to not fully encapsulate the steel making the shafts prone to corrosion and the strength of the cover concrete is locally reduced. Over the past 9 years 58, 42-inch diameter shafts have been …

Tensile Strain And Damage Self-Sensing Of Flax Frp Laminates Using Carbon Nanofiber Conductive Network Coupled With Acoustic Emission, Yanlei Wang, Guipeng Chen, Yongshuai Wang, Baoguo Han, Baolin Wan, Qingduo Hao, Yulei Bai

Civil and Environmental Engineering Faculty Research and Publications

The strain and damage self-sensing properties of carbon nanofibers (CNFs)/flax fiber-reinforced polymer (FFRP) laminates under tension were investigated via simultaneously measuring the changes of electrical resistance (ER) and acoustic emission (AE) signals. The piezoresistive mechanisms together with the damage evolution of CNFs/FFRP laminates were also explored. The results revealed that both ER and AE responses to tensile strains in CNFs/FFRP laminates could be segmented into three stages, which confirmed their good damage self-sensing ability. The isochronous and reversible electrical resistance responses to tensile strains proved the stability and repeatability of strain self-sensing capability for CNFs/FFRP laminates. Moreover, in-situ ER measurement …

Characterizing The Chemical And Microbial Fingerprint Of Unsheltered Homelessness In An Urban Watershed, Daniel Gerrity, Katerina Papp, Eric Dickenson, Meena Ejjada, Erica Marti, Oscar Quinones, Mayra Sarria, Kyle Thompson, Rebecca A. Trenholm

Civil and Environmental Engineering and Construction Faculty Research

Unsheltered homelessness is rapidly becoming a critical issue in many cities worldwide. The worsening situation not only highlights the socioeconomic plight, but it also raises awareness of ancillary issues such as the potential implications for urban water quality. The objective of this study was to simultaneously leverage diverse source tracking tools to develop a chemical and microbial fingerprint describing the relative contribution of direct human inputs into Las Vegas' tributary washes. By evaluating a wide range of urban water matrices using general water quality parameters, fecal indicator bacteria (FIB), human-associated microbial markers [e.g., HF183, crAssphage, and pepper mild mottle virus …

Fault Tolerance Analysis Of An Adaptive Neuro-Fuzzy Inference System For Mandatory Lane Changing Decisions In Automated Driving, Matthew Vechione, Ruey Long Cheu

Civil Engineering Faculty Publications and Presentations

Past research has developed a binary decision model for mandatory lane changes based on the Adaptive Neuro-Fuzzy Inference System (ANFIS). This ANFIS Decision Model (simply called ADEM), developed and tested with the Next Generation Simulation (NGSIM) data, mimics the sensory inputs and decisions of human drivers. This research assumed that ADEM will be implemented as part of the automated lane changing system in Automated Vehicles (AVs). The system in AVs will depend on active radar sensors to make measurements. The sensor outputs will be converted into the input parameter values of ADEM. This research tested ADEM's performance when the sensors …

Characterization And Performance Enhancement Of Cement-Based Thermoelectric Materials, Ruchita Jani, Niall Holmes Dr., Roger West, Kevin Gaughan, Xiaoli Liu, Ming Qu, Esther Orisakwee, Lorenzo Stella, Jorge Kohanoff, Hongxi Yin, Bartlomiej Wojciechowski

Articles

Thermoelectric materials enable the direct conversion of thermal to electrical energy. One application of this is ambient heat energy harvesting where relatively stable temperature gradients existing between the inside and outside of a building could be utilized to produce electricity. Buildings can thus change from energy consumers to energy generators. This could ultimately help reduce the surface temperatures and energy consumption of buildings, especially in urban areas. In this paper, research work carried out on developing and characterizing a cement-based thermoelectric material is presented. Cement-based samples are doped with different metal oxides (Bi2O3 and Fe2O3) to enhance their thermoelectric properties, …

Discrepancies In Changes In Precipitation Characteristics Over The Contiguous United States Based On Six Daily Gridded Precipitation Datasets, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

Variability and spatiotemporal changes in precipitation characteristics can have profound socioenvironmental impacts. Several studies have shown that the frequency and/or magnitude of precipitation events have changed over the contiguous United States (CONUS) in the past decades. Most previous studies used only one precipitation dataset and only investigated mean or extreme precipitation. Here, using 6 gridded daily precipitation datasets, we show that there are substantial discrepancies in the changes in characteristics of both extreme and non-extreme precipitation events from 1983 to 2017. Our results highlight that using a single record to study precipitation changes can potentially lead to biased results. Using …

Coevolution Of Machine Learning And Process-Based Modelling To Revolutionize Earth And Environmental Sciences: A Perspective, Mojtaba Sadegh

Civil Engineering Faculty Publications and Presentations

Machine learning (ML) applications in Earth and environmental sciences (EES) have gained incredible momentum in recent years. However, these ML applications have largely evolved in ‘isolation’ from the mechanistic, process-based modelling (PBM) paradigms, which have historically been the cornerstone of scientific discovery and policy support. In this perspective, we assert that the cultural barriers between the ML and PBM communities limit the potential of ML, and even its ‘hybridization’ with PBM, for EES applications. Fundamental, but often ignored, differences between ML and PBM are discussed as well as their strengths and weaknesses in light of three overarching modelling objectives in …

Feasibility Report On Water Recycling And The Housing Crisis, Tally A. Perry

City and Regional Planning

The western United States is experiencing increasing population, a housing shortage, and a drought. These challenges demand creative and unprecedented changes to development. Water recycling is slowly emerging as a viable solution for developers, home owners, and cities as a way to continue much-needed housing development while mitigating unnecessary water depletion. With all change, policy, feasibility, and awareness can be the largest influencers. Drought-ridden western-American states require additional and revised regulatory requirements to promote recycled water in new development. Currently, water reuse is largely used for agricultural and industrial purposes. To motivate and encourage housing development, water recycling needs to …

Evaluation Of An Equivalent Mean Grain Size Diameter To Rationally Predict The Erodibility Of Fine Riverbed Soils In Nebraska, Basil Abualshar

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The erosion of riverbed soils under the bridges is one of the major reasons that cause bridge closure or failure leading to a significant effect on the local economy. One of the commonly used methods to predict the erosion rate of soils is the excess shear stress method, which is based on two parameters describing the erodibility behavior; the erodibility coefficient and the critical shear stress. On the other hand, studies showed that the mean grain size diameter D₅₀ could be correlated to the erosion resistance of soils, usually for cohesionless soils but not for cohesive soils. It is …

Effects Of Experimental Scale On The Adsorption Of Two Pharmaceutical Drugs Detected In Municipal Wastewater Effluent, Michael Moore

Master's Theses

Pharmaceutical drugs are being produced and consumed in increasing quantities every year and are poorly treated by conventional wastewater treatment processes, leading to increasing detection of such compounds in surface water, groundwater, and municipal drinking water. Soil aquifer treatment (SAT) is a promising method for treating these emerging compounds through combined adsorption and degradation of target compounds in soil. This thesis examines the consistency of results from typical studies like adsorption isotherms and soil columns utilized in analysis of SAT performance, across varying experimental scales. The adsorption behavior of two pharmaceuticals was investigated as a function of experimental scale and …

Increasing Strength Of Plywood Shear Walls, Elizabeth Claypool, Michelle Dennin

Architectural Engineering

In a recent iteration of an upper-division engineering design lab course at Cal Poly SLO, students were challenged to identify and understand the probable failure mechanism of conventionally built plywood shear walls and hypothesize how they could delay or prevent common failure mechanisms to increase the overall lateral load capacity. After observing the results of a test on a conventional, code specified wall, a solution to integrate metal gauge strapping into edge nailing was developed to address the common failure mechanisms of nail head pull through and panel edge tear out. A shear wall with metal strapping installed between the …

Development Of Probabilistic Failure Pressure Models For Pipelines With Single Corrosion Defect, Kiswendsida J. Kere, Qindan Huang

Civil and Environmental Engineering Faculty Research and Publications

Many models have been developed in the past to predict the failure pressure of a pipeline with a single corrosion defect. However, most of the existing models are conservative and may lead to unnecessary repairs and maintenance in the pipeline risk management. The aim of this study is to develop probabilistic failure pressure prediction models that are suitable for risk assessment of corroded pipelines. The proposed models are developed at three levels of pipe ultimate strength based on a comprehensive database (consist of both experimental and numerical data) established in this study. When comparing with the existing models, it is …

Measuring Accessibility For Pedestrians, Bicyclists, And Transit Riders To Grocery Stores In The Excelsior/Outer Mission Neighborhoods Of San Francisco, Alexandra Lee-Gardner

Master's Theses

Grocery stores are an important amenity in neighborhoods and access to grocery stores is important for health and well-being. While grocery store accessibility is a popular topic of research, studies measuring access for pedestrians, bicyclists, and transit riders are extremely rare. When a new store opened in the Excelsior/Outer Mission districts of San Francisco on a street lacking basic infrastructure for pedestrians, bicyclists, and transit riders, the importance of this study became apparent. The Excelsior/Outer Mission neighborhood has a shocking number of collisions (over 1,100 between 2015 and 2019), elevated levels of walking, biking, and transit ridership, and minimal safe …

Numerical Modelling Of Externally-Bonded Fiber Reinforced Polymer Shear-Strengthened Reinforced Concrete Beams Subjected To Fatigue Loading, Nagwa Ibrahim Fares

Theses

An extensive number of existing structures persistently exposed to fatigue loading such as bridges, offshore structures, pavements, and highways, are in urgent need of repairing and strengthening. This may be attributed to the continuous increase in the load requirements, change of the structure’s function, and meeting current load standards. Among the potential methods of rehabilitation and strengthening of existing reinforced concrete structures, the externally bonding fiber reinforced polymers (FRP) composites are gaining massive popularity and becoming a viable and cost-effective method. Shear failure of reinforced concrete (RC) beams is known to be brittle, which occurs without prior sufficient warnings; therefore, …

Using Metal-Organic Frameworks (Mof) To Reduce The Carbon Footprint Of Concrete, Mona Ibrahim El-Hallak

Theses

The production of concrete by the construction industry has a massive impact on the environment. The process of manufacturing its main component, cement, releases a considerable amount of anthropogenic carbon dioxide. This thesis is concerned with the production of sustainable and eco-friendly concrete that integrates metal-organic frameworks (MOF) to capture and offset the CO₂ emissions emitted during the production of cement. The main objective is to synthesize a MOF capable of capturing CO₂ in concrete through accelerated carbonation curing and to assess its impact on concrete performance. Different parameters were examined, including the MOF content, initial curing duration, …

The Impact Of Material And Environmental Properties On The Ettringite - Metaettringite Thermochemical Reaction, Aaron Strand

Dissertations

The use of energy is an essential need for people, with demand constantly increasing due to an increasing population and an increase in living and comfort standards. Since 1965, world energy consumption has quadrupled. During peak utilization, the strain on the grid infrastructure can be immense. As energy demand fluctuates during different times of the day and year, the energy production needs to scale accordingly This creates inefficiencies within the system such as over building generation capacity or losses from start up or ramping up production. This can be alleviated through load leveling where excess energy generated during low demand …

Partial Systems' Analysis Of Traffic Noise Reduction In Tarik Al Jadidah, Beirut, Ibtihal Y. El-Bastawissi, Nour El Baba, Shireen Khalil, Nour El Hage, Rouba Joumblat, Franz Gatzweiler

BAU Journal - Creative Sustainable Development

Traffic noise is considered one of the main pollutants in an urban space and has multiple side effects regarding the physical and mental health of the human being. Tarik Al Jadidah, one of the most densely populated neighborhoods in Beirut City- Lebanon, is selected as urban area for a project-based initiative and the focal point of different studies in BAU Urban Lab. The area suffers from various urban problems, but prominently traffic noise that highly damages the urban residents' quality of life due to its high levels of traffic noise that surpasses the World Health Organization (WHO) guidelines.

BAU Urban …

Evaluating And Incorporating Site Variability In Different Geotechnical Engineering Applications, Md Habibur Rahman

LSU Doctoral Dissertations

Site investigation and characterization of subsurface soil conditions are crucial for geotechnical engineering design and analysis. Geotechnical properties vary inherently from one point to another within the same site. This study focused on evaluating the site variability from cone penetration tests (CPT) and soil boring data, and its implementation into the Load and Resistance Factor Design (LRFD) formulation. The total Coefficient of Variation (COV_R,total) for each site was estimated from COV_R,spatial (Spatial Coefficient of Variation) and COV_R,method (Method Coefficient of Variation) which were then used to calibrate the resistance factors (ϕ_spatial, ϕ_total) …

Hydrodynamic Limitations To Mangrove Seedling Retention In Subtropical Estuaries, Kelly M. Kibler, Christian Pilato, Linda Walters, Melinda Donnelly, Jyotismita Taye

Flow-biota Interaction and Natural Infrastructure Design

Mangrove forest sustainability hinges upon propagule recruitment and seedling retention. This study evaluates biophysical limitations to mangrove seedling persistence by measuring anchoring force of two mangrove species (Rhizophora mangle and Avicennia germinans). Anchoring force was measured in 362 seedlings via lateral pull-tests administered in mangrove forests of two subtropical estuaries and in laboratory-based experiments. Removal mechanism varied with seedling age: newly-established seedlings failed due to root pull-out while seedlings older than 3 months failed by root breakage. Anchoring force of R. mangle seedlings was consistently and significantly greater than A. germinans (GLM: p = 0.002), however force to …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

Investigation Of Elastic Parameters And Pavement Modeling With Eps Geofoam, Engda Kassahun Temesgen

Dissertations - ALL

Models using EPS geofoam rely on input elastic parameters derived from compression tests on small size samples. Young's modulus and Poisson's ratio are parameters required to model isotropic and homogenous material behavior. For the most widely used EPS density grade of 20 Kg/m3 (1.25 pcf), Young's modulus of 4 MPa and Poisson's ratio of 0.1 are commonly used. Use of these values in models led to unreasonable long term deformation predictions that contradicted with field observations. Tests on small samples are prone to edge effects. Edge effects in turn result in underestimation of input elastic parameters. Alternative tests and sensing …

Transformational Leadership And The Adoption Of Sustainability And Asset Management Practices In Ground Transportation Organizations, Mohammad M. Bushahri

Dissertations - ALL

The unprecedented challenges the infrastructure domain has been facing for the past few decades are forcing the authorities and owners of relevant organizations, particularly within the ground transportation sector, to introduce more innovative measures and to mitigate risks by embracing and adopting sustainability and asset management practices. This study examined the relationship between transformational leadership and the embracing and adopting of sustainability and asset management practices in the U.S. ground transportation sector. Further, this study assessed the mediation effect of organizational innovation on the relationship between transformational leadership style and the leaders' perception in terms of adaptation of sustainability and …