Civil Engineering Commons^™

Calcium Based Carbon Negative Fillers And Additives: Effects On Hydration And Performance Of Low-Carbon Cement Systems, Smita Bhowmick Shithi

Masters Theses

Cement production is a major source of global CO₂ emissions creating an urgent need for carbon-negative fillers and functional additives that lower clinker use while maintaining cement performance. This thesis investigates the effects of organic mineral salts as fillers and additives on cement hydration, fresh properties, compressive strength and pore structure. In the first study, ordinary Portland cement (OPC) was partially replaced with calcium carbonate or calcium oxalate to enable a direct comparison under controlled particle size distribution (PSD). Rheology, flowability, hydration kinetics, phase evolution, mechanical performance and water absorption were evaluated. Calcium carbonate promoted early hydration through nucleation and …

Bond Behavior Of Magnesium Potassium Phosphate Cement (Mkpc) Coating For Steel Reinforcement, Eric Williams

Masters Theses

"This research investigates the bond behavior of magnesium potassium phosphate cement (MKPC) coated mild steel deformed bars in conventional concrete and concrete repair materials. For typical steel reinforcement in concrete, a thin “passive layer” develops around the reinforcement, which protects the reinforcement from corrosion. The concrete carbonates over time, reducing the protection of the passive layer and allowing chlorides, which corrode the reinforcement, to penetrate at an increasing rate. In some cases, to combat this corrosion, a protective layer is added to the reinforcement prior to installation. Common protective layers include epoxy coatings or zinc galvanization. MKPC is a novel …

System Design For Highly Accurate And Efficient Target Detection In Triaxial Testing, Qingqing Fu

Masters Theses

Accurate and automated recognition of coded targets is crucial for high-precision photogrammetry-based measurements in triaxial testing. Traditional recognition methods, including those based on deep learning and table decoding, often struggle with issues such as perspective distortion, rotation, and variable lighting, leading to unreliable results. While deep learning approaches offer some improvements, they remain computationally intensive and sensitive to environmental factors.

This thesis introduces an innovative system that replaces deep learning algorithms with a blob analysis-based method for efficient and robust recognition of coded targets. The system also employs newly designed solid points of varying sizes and patterns, eliminating the need …

Gfrp Reinforced Bridge Barriers: Experiment Testing, Manish Kumar Gadhe

Masters Theses

This study focused on evaluating the performance of concrete bridge barriers reinforced with Glass Fiber Reinforced Polymer (GFRP) compared to those reinforced with conventional mild steel. Four full-scale barriers were constructed, three using GFRP bars as the reinforcement and one with mild steel reinforcement. These were cast on two concrete slabs to ensure consistent support conditions. The use of GFRP aims to address durability concerns associated with steel reinforced concrete (RC), particularly corrosion of these bars in harsh environments.

To simulate real-world impact scenarios, a weighted cart was launched at each barrier using a guided sled system. Sensors, including load …

Designing Exterior Lighting For Safety And Comfort While Minimizing Light Pollution, Energy Consumption, And Cost, Stephen Michael Simmons

Masters Theses

"Artificial light at night brings many benefits to society. However, these benefits do not come without costs. One environmental issue that is often overlooked in the design of public spaces and infrastructure is light pollution. At the expense of large amounts of energy, light pollution causes numerous harmful effects on human health, ecosystems, and the night sky. Today, the problem is becoming more widespread, especially with the increasing use of bright, white LED luminaires. Thus, it is imperative for designers and engineers to create smarter lighting designs that not only allow for safety and comfort at night but also promote …

Selecting Consolidation Procedures For Making Concrete Specimens, Paige Marie Toebben

Masters Theses

"The goal of this research was to reevaluate ASTM C31 Standard Practice for Making and Curing Concrete Test Specimens in the Field, as well as deepen our understanding of the relationship between the consolidation process, concrete composition, and workability. An improved understanding of this area will help to reduce variability in concrete quality. The project involved evaluating the effect of different consolidation methods on concrete specimens with changing levels of workability. To do this, concrete cylinders were created with varying viscosities by adjusting the water-to-cement ratio (w/c) and water-reducing agent. More cylinders were created with varying paste volumes while keeping …

Effect Of In-Situ Formed Nano-Calcite Particles On Hydration And Properties Of Cement-Based Materials, Bowen Tan

Masters Theses

The in-situ preparation of nano-calcite via bubbling method and the effects of the nano-calcite on the hydration process and properties of the cement-based materials are investigated in this research. The nano-calcite is synthesized under different conditions and added into Portland cement to prepare test samples. The bubbling method is then introduced in upcycling the municipal solid waste incineration (MSWI) ashes, and the effects of the upcycled MSWI ashes on the hydration of Portland cement is investigated. Experimental results illustrate that the COâ‚‚ bubbling method can produce nanometer-to-sub- micron-sized calcite particles, and the synthesis rate and the morphology of the nano-calcite …

Numerical Behavior Of Steel H-Plies Repaired Using Layered Concrete Jacket, Fareh Waleed Abudawaba

Masters Theses

“This study developed finite element models (FEMs), using LS-Dyna software, to investigate the repair of corroded steel H-piles using concrete jacket. The concrete modeled as a layered material simulating 3D printed concrete. 3DPC is a new technology that can be used to repair or build structures without formwork by depositing concrete mixture layer by layer. For the 3DPC, this study investigated the feasibility of using alkali-activated concrete (AAC) synthesized using class C fly ash as the main binder. The fresh properties, extrudability, and buildability of the proposed concrete were investigated through open time and deformation tests, respectively. Hardened properties were …

Early Wildfire Detection By Air Quality Sensors On Unmanned Aerial Vehicles: Optimization And Feasibility, Doaa Rjoub

Masters Theses

“Millions of acres of forests are destroyed by wildfires every year, causing ecological, environmental, and economical losses. The recent wildfires in Australia and the Western U.S. smothered multiple states with more than fifty million acres charred by the blazes. The warmer and drier climate makes scientists expect increases in the severity and frequency of wildfires and the associated risks in the future. These inescapable crises highlight the urgent need for early detection and prevention of wildfires. This work proposed an energy management framework that integrated unmanned aerial vehicle (UAV) with air quality sensors for early wildfire detection and forest monitoring. …

Effect Of Spike Anchors On The Bond Behavior Of Steel Reinforced Polymer Composite Externally Bonded To A Concrete Substrate, Keenan Lorence Mcburney

Masters Theses

Steel reinforced polymer (SRP) composites are a strengthening material that consist of continuous high-strength steel cords embedded in a polymeric matrix. SRP has demonstrated a high potential for providing additional flexural and shear strength in existing concrete structures when bonded to the concrete surface. However, premature debonding from the concrete substrate at low load levels is a major shortcoming of SRP composites. It has been demonstrated in previous studies that anchors can limit the effect of debonding in fiber reinforced polymer (FRP) composites by increasing the load capacity and ductility of the composite-concrete interface.

This study aims to investigate the …

Optical Fiber Based Integrity Test Of Civil Engineering Materials: Numerical Analysis, Ruoyu Zhong

Masters Theses

“Major advancement in Civil Engineering cannot be accomplished without the help of sensors. Among different types of sensors, fiber-optic sensor is known for its light weight, high accuracy, resolution, immunity to electromagnetic interference, and resistance to harsh environment. This research mainly focuses on fiber-optic sensor application on concrete structures as temperature sensor. Thermal Integrity Profiling (TIP) is a non-destructive integrity testing method which makes use of the hydration heat from the concrete curing process to detect defects within a drilled shaft. Any defect of concrete could result in a temperature anomaly in a drilled shaft. The accuracy of the current …

Feasibility Study On Novel Fire-Resistant Coating Materials, Anyou Zhu

Masters Theses

“Over the past decades, wildfires in the United States have caused severe damage and property losses. The California Camp Fire in November 2018 caused 85 civilian fatalities and destroyed 18,793 structures. There is a need to enhance the fire resistance of structures and buildings. The primary purpose of this study was to develop innovative surface-bonded fire-resistant material that can be used as a wall coating with three primary features: (a) workability for application, (b) enough adhesion to the surface of the structure, (c) fire-resistant. This research developed mix designs of innovative fire-resistant coating materials including high-performance cement mortar (HPCM), geopolymer …

A Study On End-Anchorage And Bond Behavior Of Steel-Fiber Reinforced Cementitious Matrix Composites Externally Bonded To A Concrete Substrate, Christopher Michael Moore

Masters Theses

"Fiber reinforced cementitious matrix (FRCM) composites are a strengthening material consisting of continuous fibers embedded in an inorganic matrix that have the potential to provide additional flexural and shear strength to concrete and masonry members. When used for external strengthening, however, debonding of the material is often observed due to slippage of the fiber with respect to the matrix, causing loss of composite action and a reduction in load carrying capacity. The composite utilized in this study consisted of continuous steel fibers embedded in an inorganic cementitious matrix bonded to a concrete prism. Additionally, an end-anchorage system was implemented with …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Changes In Fresh Properties Of Flowable Concrete Induced By Pumping And Composition Of The Lubrication Layer, Alexis Salinas

Masters Theses

"Pumping is an easy method to move concrete while keeping stability. It is worldwide accepted as one of the principal methods for concrete placement, as it accelerates construction. Typically, concrete acceptance in terms of fresh quantitative empirical properties (i.e. slump/slump flow and air content) are performed prior to the pumping process. However, empirical measurements have the drawback that they only measure 1 point. Rheology is better tool to evaluate the behavior of concrete. Pumping is a process that induces considerable shearing in the concrete that can impact its rheological properties. Therefore, the magnitude of these changes in fresh properties depends …

Abrasion Resistant Concrete Mix Design For Cold Climates, Diane Mariah Murph

Masters Theses

“Studded tire usage in Alaska contributes to rutting damage on pavements resulting in high maintenance costs and safety issues. In this study, binary, ternary, and quaternary highly-abrasion resistant concrete mix designs using supplementary cementitious materials (SCMs) were developed. The properties of fresh concrete and mechanical, and durability properties of hardened concrete for these mix designs were then tested to determine an optimum highly-abrasion resistant concrete mixture which could be placed in cold climates to reduce rutting damage. SCMs used included silica fume, ground granulated blast furnace slag, and type F fly ash. Tests including workability, air content, drying shrinkage, compressive …

Unmanned Aerial And Traversing Vehicle -- A Mobile Platform For Bridge Inspections, Clayton A. Fritsche

Masters Theses

“Unmanned aerial vehicles (UAVs), also known as drones, have been rapidly growing in popularity since their creation. This study aimed to create a robotic platform used to assist in the inspection process of the nation’s aging and deteriorating bridges. To this end, a multimodal inspection robot that utilized both flying and driving technologies, was designed, analyzed, and tested for aerial, traversing, and their transitional operability. The design, herein referred to as the “BridgeBot”, was evaluated both computationally and experimentally. A finite element model of the BridgeBot was established and analyzed under static loading scenarios to help determine stress distributions and …

Performance Of One-Part And Two-Part Class C Fly Ash-Based Alkali Activated Mortars, Cedric Chani Kashosi

Masters Theses

“Seeking an eco-friendly concrete, researchers have conducted studies to fully replace ordinary Portland cement (OPC) with fly ash (FA) producing alkali-activated concrete (AAC). Results showed better performance of AAC in terms of high early compressive strength, and durability compared to conventional concrete. However, much is still unknown about the behavior of AAC. From the type of materials used, the curing procedure, and long-term strength development of these binders; a thorough investigation is needed in order to fill the existing gap from previous studies and thus make a step forward to the safely use of AAC in the construction industry. The …

Feasibility Study For Sustainable Controlled Low-Strength Material (Clsm) Incorporating Off-Specification Fly Ash And Bottom Ash, Alexis K. Vandomelen

Masters Theses

“Controlled low-strength material (CLSM) is a self-consolidating cementitious material used in applications requiring high flowability and low strength. The primary components of this material, being cement and sand, however, negatively impact the environment. Cement is a large contributor to CO2 emissions, and the vast depletion of sand causes physical and political issues. Furthermore, over 100 million short tons of coal combustion products (CCP), including fly ash and bottom ash, are created annually in the United States, while nearly half of all CCP remain unused. No off-specification fly ash has been implemented in CLSM. This study uses coal ashes sourced from …

The Passive Effects Of Full-Gateway, In-Street Signs On Vehicular Speed, De'lon Dixon

Masters Theses

Reducing motorist’s speed when approaching crosswalks is an important goal in reducing the number of collision between motorist and pedestrian in crosswalks. The current study addresses this goal. The effect of gateway installation of in-street signs (one in-street sign installed between the two travel lanes in each direction and one on both edges of the roadway in each direction) on vehicle speed was evaluated on nine roads. The results demonstrated that the Gateway in-street sign treatment produced large speed reductions as vehicles approached the crosswalk and at the crosswalk. The average speed reduction was 3.8 mph at the crosswalk and …

Enabling Robust Distributed Real-Time Hybrid Simulation Method And Expanding Its Applications In Floating Wind Turbine Systems, Mehmet Cinar

Masters Theses

Real-time hybrid simulation (RTHS), which integrates physical experiment and numerical simulation, plays an essential role in understanding the time-dependent behavior of structures when subject to hazardous loadings. On the other hand, RTHS might not yield accurate results for complex structural systems due to experimental and computational limitations. Distributed real-time hybrid simulation (dRTHS), which takes the advantage of distributed laboratory facilities using network communications, was proposed and proven to address some limitations in RTHS. During dRTHS, Internet delay due to the network communication is added to the actuator delay in RTHS, which may cause inaccurate results or even unstable tests. To …

Maintaining Deck Profile In Steel I-Girder Bridges During Deck Placement, Ali Naif Inceefe

Masters Theses

Conventional steel I-girder highway bridges utilize cast-in-place concrete deck. Maintaining the deck profile as per project specifications might be a challenging task. Deformation of girders and formwork used for deck placement need to be controlled during deck placement. Differential deflection between girders, exterior girder web out-of-plane deformation, exterior girder warping, or a combination thereof could impact the deck profile. These deformations challenge maintaining deck profile and need to be considered as a part of constructability evaluation. Determining deck profile due to potential girder deformations is necessary before deck placement so that the remedial actions can be implemented when deck finish …

From Architectural Design To Structural Analysis: A Data-Driven Approach To Study Building Information Modeling (Bim) Interoperability, Mohammed Aldegeily

Masters Theses

BIM has been playing an essential role in building construction projects in recent years. It was used to automate many tasks such as clash detection, 4D planning, and quantity takeoff, among others. However, the interoperability of BIM still lacks in many fields across the architecture, engineering, and construction domains. This research studies the interoperability between architectural design and structural analysis. The goal is to explore structural analysis of BIM models through data transfer processes between different software platforms via three types of paths: (1) Application Programming Interface (API); (2) “immediately connect,” which is the direct link between software programs from …

Compressive Behavior Of Masonry Columns Confined With Steel Reinforced Grout (Srg) Composite, Sarah Elizabeth Jemison

Masters Theses

"In this study, a new type of composite comprised of steel fiber cords embedded in a natural hydraulic lime mortar matrix, known as steel reinforced grout (SRG), is explored for the use in confinement of masonry columns. An experimental study was carried out to understand the behavior of solid clay brick masonry columns confined by SRG jackets. Twenty-four confined and seven unconfined columns with a square cross-section were tested to failure under a monotonic concentric compressive load. Test parameters considered were the column corner condition, number of fiber jacket layers, and number of fiber overlapping faces. SRG confinement improved the …

Numerical And Experimental Analysis Of Local Buckling Of Axially Loaded Steel Tubes Confined By Concrete And Frp, Nicholas Colbert

Masters Theses

“The hollow core Fiber-Reinforced-Polymer (FRP) concrete circular-steel (HC-FCS) column consists of an outer circular fiber reinforced polymer (FRP) tube, an inner thin-walled circular steel tube concentrically aligned, and a concrete shell between them. Research has been performed on the performance of the member as a whole, but to date, there has been no investigation into the behavior of the steel tube confined in the column. 17 small-scale columns were tested under axisymmetric axial compressions applied directly to the steel tube under displacement control. The conducted parametric study examined the effects of diameter-to-thickness (D/t) ratio, concrete unconfined compressive strength, FRP thickness, …

Thermal Curing Efficiency Of Geopolymer Mortars, Simon Peter Sargon

Masters Theses

”Missouri is the fourth largest coal consumer in the U.S. with coal-fired power plants generate 81.3% of the electricity in the state which generate about 2.7 million tons of coal combustion residuals (CCRs) annually. The CCR, including fly ash, disposal issue is not limited to Missouri, rather it is a national issue with CCRs being the second largest waste stream in the U.S. Ninety million tons of fly ash are stored in landfills and ash ponds annually. Hence, using this waste product effectively is necessary. One of the emerging applications of fly ash is to use it as binder in …

Field Implementation Of Cement-Based Composite Strengthening Technologies, Michael Andrew Janke

Masters Theses

"With infrastructure continuing to age, technologies are being developed to strengthen structures as a more sustainable option than replacement. The use of fiber-reinforced cementitious matrix (FRCM) strengthening systems is a promising new technology for adding flexural and shear capacity to existing reinforced concrete members. While cement based systems with carbon, PBO, and steel have all been implemented in a lab setting, there is not research data available for installation in the field. FRCM composites have advantages over more widely used fiber reinforced polymer (FRP) composites such as heat resistance and compatibility with concrete substrate. FRP systems have previously been field …

Implementing Online Updating To Complex Hysteresis Models In Real- Time Hybrid Simulation Using Constrained Unscented Kalman Filter, Bilal Ahmed Mohammed

Masters Theses

Although conventional experimental methods, such as quasi-static testing, shake table testing, etc., perform well to evaluate structural seismic performance necessary for modern seismic design, the quasi-static loading and/or reduced scale specimen used in shake table testing may not provide true dynamic responses of structural systems. To overcome these limitations, real-time hybrid simulation (RTHS) was developed, which is a combination of physical testing of the experimental substructure and analytical simulation of the numerical substructure. With the advancement of hybrid simulation, it is now possible to economically test large to full-scale specimens in laboratories at the real earthquake rate. Online model updating …

Extending Time Series Forecasting Methods Using Functional Principal Components Analysis, Isaac Michael Wagner-Muns

Masters Theses

"Traffic volume forecasts are used by many transportation analysis and management systems to better characterize and react to fluctuating traffic patterns. Most current forecasting methods do not take advantage of the underlying functional characteristics of the time series to make predictions. This paper presents a methodology that uses Functional Principal Components Analysis (FPCA) to create smooth and differentiable daily traffic forecasts. The methodology is validated with a data set of 1,813 days of 15 minute aggregated traffic volume time series. Both the FPCA based forecasts and the associated prediction intervals outperform traditional Seasonal Autoregressive Integrated Moving Average (SARIMA) based methods"--Abstract, …

Application Of Wavelet Transform In Structural Health Monitoring, Yashodhya Swarna Sri Dhanapala Liyana Kankanamge

Masters Theses

Structural Health Monitoring (SHM) is a process of implementing a damage detection strategy in structures to evaluate the condition of existing structures to ensure the safety of users in the future. The changes in the material, geometric and/or structural properties affect structural responses, which can be captured and analyzed for condition assessment. Various vibration-based damage detection algorithms have been developed in the past decades. Among them, the Continuous Wavelet Transform (CWT) gained popularity as an efficient method of signal processing to build a framework to identify model properties and detect damage in structures. In this study, the application of wavelet …