Civil Engineering Commons^™

A Machine-Learning-Based Systematic Framework For Modeling Compression And Recompression Indices For Florida Soils, Michael Morales

Doctoral Dissertations and Master's Theses

This thesis develops a machine-learning framework for estimating the compression index and the recompression index of Florida soils from routinely measured index properties, and reports two studies that build it. Consolidation settlement design requires both indices, and both are obtained from the incremental-loading oedometer test, which occupies a specimen for one to two weeks; the index tests that accompany it are complete within hours. Empirical correlations have filled that interval since the 1950s, but their coefficients are calibrated on specific soil populations and transfer poorly between regions. The first study analyzes 376 consolidation tests compiled for the Florida Department of …

Analysis And Design Of Auger Cast Piles With Isolation Casing, Zachary Lindsay

Master's Theses

This research addresses the analysis and design of double cased piles. Bay Area Rapid Transit (BART) runs a large rail system both above and below ground that connects the entire Bay Area. BART requires that all new constructions avoid transmitting axial load to their tunnels from adjacent piles. If piles fall within the zone of influence, builders must install double cased piles. Double casing is where there is an extra casing around the pile, with an air gap between them. The air gap prevents load from transferring to the outer casing. The length of this casing is called the isolation …

Effect Of Snow Melt On Slope Stability, Gustav G. Gothberg

Williams Honors College, Honors Research Projects

This project explores the effect of snow melt on slope stability. The different types of slope failure are examined to determine which are most affected by snow melt. Then, the report examines the equations that geotechnical engineers use to determine the exact moment when a slope fails. Using GeoStudio modeling software, Slope/W, landslides caused by snow melt were modeled. GeoStudio was also used to explore methods of mitigating the effects of snow melt. This project also explores how to take advantage of these models to minimize the damage done by landslides.

Reliability-Based Performance Evaluation Of Slurry Wall For Leakage Control At Chakaria Landfill, Bangladesh, Shishir Bhandari

Civil Engineering Theses

Landfill leachate threatens groundwater quality in low-lying coastal Bangladesh, where a shallow water table and a discontinuous natural clay barrier heighten contamination risk beneath municipal solid waste sites. At the Chakaria Landfill in Cox's Bazar District, a cement-bentonite slurry wall was proposed as a vertical cutoff to control seepage, but its reliability under the site's high-groundwater condition had not previously been evaluated in probabilistic terms.

This study evaluated the wall's performance using a two-dimensional SEEP/W finite-element seepage model, a validated response surface (RSM) equation relating seepage rate to wall permeability, thickness, depth, and a Hasofer-Lind first-order reliability (FORM) analysis built …

Impact Of Natural Disasters On Construction And Engineering Solutions, Karima Ao Damson

Williams Honors College, Honors Research Projects

This Honors Research Project seeks to research and explain the impact of natural disasters on the construction and reconstruction of infrastructure in countries with the highest risk of natural disasters and compare them to the requirements in the United States in the states most prone to natural disasters. The objectives are to identify the countries most prone to natural disasters, describe the environmental impacts of the natural disasters, describe the impacts on construction and reconstruction requirements, and research whether construction and civil engineering solutions currently applied to the individual countries could be improved or reproduced in other countries exposed to …

Pile Setup Effects On Driven Piles In Southeastern Coastal States, Peya Sharif

College of Graduate Studies: Theses & Dissertations

The resistance of driven piles typically increases with time after installation, a phenomenon known as pile setup. This behavior is primarily associated with the dissipation of excess porewater pressure and the progressive reconsolidation of soil surrounding the pile shaft, particularly it is observed in cohesive soils. Although several empirical and analytical models have been proposed to estimate pile setup, their practical implementation in foundation design remains limited due to uncertainties associated with soil conditions, pile geometry, resistance variability, and time dependent behavior. To address some of these uncertainties, this study collected 221 pile load test data at the End of …

Potential Of Stamp Sands As Cemented Tailings, Samuel Sukaria

Dissertations, Master's Theses and Master's Reports

Worldwide mine tailings ponds and reservoirs occupy some 534 billion m³ of space with the volume expected to increase as economic demand for minerals increases over the next decades. These reservoirs produce adverse effects on local communities and ecosystems through structural failure resulting in mass flooding events, drainage of pollutants into water supply and emissions of airborne particulate matter. Methods developed to find use for tailings include extraction of residual minerals and aggregates in construction materials. The latter method has already been used in mining operations to stabilize mining reservoirs and stopes, and as placement for temporary road work …

Downdrag Defeated – The Neutral Plane Method, Kyle L. Zak, Min Sang Lee

Civil Engineering Professional Development Seminar

The neutral plane method for evaluating downdrag on deep foundations has been gaining popularity over the past few years. It is a powerful tool that, in many situations, can all but eliminate downdrag concerns on deep foundations. INDOT has allowed its use recently and adapted its forms to accommodate this method. The presentation will cover the theory behind the method and how it can be applied in bridge design. We will then demonstrate how to incorporate the method into the INDOT workflow, and we’ll show a couple real-life examples where the neutral plane method saved the day.

Development Of New Design Criteria For Coastal Highway Embankment Under Wave-Induced Loading, Udaya Bilas Panta

Master's Theses

In the face of intensifying hurricanes and rising sea levels, Louisiana’s coastal highways, lifelines for communities and commerce, stand increasingly vulnerable. This thesis introduces a pioneering methodology for designing geosynthetic-reinforced highway embankments capable of withstanding wave-induced loading and rapid drawdown scenarios, the most critical failure condition identified in coastal environments. By integrating statistical wave modeling, advanced numerical simulations using SEEP/W and SLOPE/W, and a comprehensive parametric analysis, the study develops a novel hybrid regression formula that accurately predicts optimal reinforcement lengths based on site-specific geotechnical and hydraulic parameters. Validated against Hurricane Katrina data and real-world soil profiles from Cameron Parish, …

Experimental And Numerical Investigation On The Effect Of Projectile Mass And Apex Angle On Penetration Depth Into Sandy Soils, Abdul-Rahman K. Osman, Ahmed Elshesheny Dr, Mohamed S. Zahran Dr, Nabil M. Nagy Prof.

Journal of Engineering Research

Projectile penetration in granular soils remains a critical concern in defense engineering and ballistics research. This study presents an experimental and numerical investigation of rigid cone-tip projectile penetration into very dense sand, examining the influence of apex angle and projectile weight on penetration depth. Laboratory experiments were conducted using metallic projectiles with apex angles of 10°, 30°, 60°, and 90° and weights of 2.445, 3.87, 5.33, and 6.81 kg, dropped from a height of 4.295 m into a 500×500×500 mm wooden tank filled with sand to 400 mm height at 95% relative density. Through systematic testing, two empirical correlation …

Biochar-Based Filtration And Barrier Systems For Urban Stormwater Treatment, Krishna R. Reddy

Stormwater Drainage Conference

Conference that deals a wide range of issues dealing with stormwater drainage. Professor Krishna Reddy of University of Illinois Chicago presented an invited talk titled "Biochar-Based Filtration and Barrier Systems for Urban Stormwater Treatment"

Use Of Pushed-In Pencel Pressuremeter Test For Shallow Foundation Design In Florida Fine Sands, Brhane Weldeanenya Ygzaw

Theses and Dissertations

A comprehensive evaluation was conducted on the performance, consistency, and practical application of various in-situ geotechnical testing methods for predicting the settlement and bearing capacity of shallow foundations in Florida’s fine sands. The methods assessed include the Standard Penetration Test (SPT), Cone Penetration Test (CPT), Dilatometer Test (DMT), pushed-in PENCEL Pressuremeter Test (PPMT), and the pre-bored TEXAM Pressuremeter Test. A dual approach controlled indoor testing at the FDOT State Materials Office (SMO) and field investigations at three representative sites (Kingsley, Trenton, and the UCF research site), formed the experimental foundation.

Over thirty settlement prediction techniques and thirteen bearing capacity estimation …

Hickory Street Square Revitalization, Spencer Knight, Grace Dungan, Tim Kula, Evan Lauritsen, Lindsey Mennenga

Honors Program: Senior Projects (Public)

The Hickory Street Square Revitalization Project seeks to transform a central public space in Sidney, Nebraska into a dynamic, community-oriented area that supports local events, economic activity, and cultural heritage. The project addresses six core objectives: 1) convertible street design, 2) parking lot reconfiguration, 3) public amenities, 4) event flexibility, 5) lighting and signage, and 6) old electric plant renovation. A conceptual design was developed by the design team (S.T.E.E.L. Sentinel Solutions) by synthesizing the most effective features of three preliminary alternatives, shaped further through community feedback and evolving project constraints. The final project design minimizes disruption to existing activity …

A Review Of Chemical Stabilisation Used To Enhance The Mechanical Properties Of Rammed Earth, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Rammed earth is a sustainable construction method with a lower carbon footprint and embodied energy compared to traditional materials like steel and concrete. However, its lower mechanical properties when compared to these forms of construction make it vulnerable to seismic forces. This paper reviews the published literature on enhancing rammed earth's mechanical properties through both chemical stabilisation and fibre reinforcement, with a focus on reusing waste materials. The effectiveness of these techniques are highlighted by comparing experimental results with minimum specifications taken from relevant guidelines and standards for building rammed earth structures in seismic zones. These findings demonstrate that chemical …

Earthquake Wrangler: Leveraging Ios Technology For Earthquake Detection And Early Warning Application To Enhance Public Safety., Luis F. Salome

Theses and Dissertations--Civil Engineering

Earthquakes are devastating natural phenomena and generate secondary hazards such as tsunamis, landslides and fires. Their catastrophic impacts span both developed nations including the United States, Japan, Turkey, and Italy and developing countries such as El Salvador, Haiti, Nepal and the Philippines, where disparities in early warning infrastructure remain important. Seismic events start with stress waves generated by tectonic plate motion, with body waves (P- waves and S-waves) and surface Rayleigh and love waves that carry energy through the earth. While some regions have adopted advanced early warning systems based on seismic hazard models and strong ground motion analysis, others …

Software Literacy In Construction, Aidan Cazares

Williams Honors College, Honors Research Projects

The construction industry increasingly relies on software like Bluebeam Revu for their quantity takeoff, document management, and collaboration needs. This project will outline pertinent information obtained through their Bluebeam professional training program and reflect it with a detailed estimate of a real life construct project.

Estimating Unconfined Compressive Strength (Ucs) Of Rocks From Measurement While Drilling (Mwd) Data, Can Erdem

Dissertations, Master's Theses and Master's Reports

Measurement-while-drilling (MWD) technology enables the real-time monitoring of drilling parameters during the drilling process. MWD data can provide valuable insight into the mechanical behavior of intact rocks and rock masses, which is essential for geotechnical applications such as foundation design and underground construction. The aim of this study is to correlate real-time drilling parameters, recorded using a laboratory-developed MWD system, with the unconfined compressive strength (UCS) of rocks. A custom laboratory MWD system was designed to simultaneously record four key drilling parameters: thrust (axial force, crowd), torque, penetration rate, and rotational speed. The custom-built MWD system was used to continuously …

Assessment Of Surface Area Application Ratios For Beach Sand Treated Via Surface Percolated Micp-Bioslurry For Erosion Mitigation, Connor J. Marlin

UNF Graduate Theses and Dissertations

Rapid shoreline erosion associated with sea-level rise is an ongoing threat to coastal infrastructure. Traditional stabilization techniques, such as revetments, seawalls, and periodic nourishment, often prove costly, ecologically disruptive, or provide only temporary protection. Microbially Induced Calcite Precipitation (MICP) and its operational variant, bioslurry, present a biologically inspired alternative capable of forming a cemented surface crust that reduces soil erodibility. Previous laboratory studies typically prescribed a solution dosage as a percentage of pore volume (%PV). While geotechnically sound, this metric is poorly suited to field deployment across a large area. This thesis evaluates surface-area-based dosing (L/m²) as the primary dosage …

Assessment Of Wave Climate Conditions At An Important Historical And Ecological Site Along The Fort George River In Northeast Florida, Ally O. Kasuwi

UNF Graduate Theses and Dissertations

This study investigated wave climate conditions at the Timucuan Preserve in northeast Florida, addressing gaps in previous shoreline erosion research that largely attributed erosion to boat wakes without detailed wave data. Field data were collected using several do-it-yourself water wave gauges. Each data collection event was for approximately one week, with an emphasis on collecting data before, during, and after periods of expected peak wave activity (i.e., holiday weekends and large-scale storms). Data were analyzed in the frequency domain to establish the likely cause of waves. Results suggested that, counterintuitively, watercraft traffic may have produced higher dominant wave periods than …

Assessing The Environmental Impact Of Municipal Solid Waste, Ojo Oluwayinka Florence, Olaniyan Olatunji Sunday, Akolade Adebola Saheed, Alabi Oluwaseyi Omotayo, Olaomotito Precious Adesope, Adebayo Kehinde John

Journal of Environmental Science and Sustainable Development

Municipal solid waste (MSW) management presents significant environmental challenges, especially with increasing urbanization and population growth. This study assesses the environmental impacts of MSW, focusing on waste composition, management practices, and their effects on air, water, and soil quality. The primary objective is to evaluate how MSW contributes to environmental degradation and to explore strategies for mitigating these impacts. A hypothesis was developed that optimizing waste composition through proper sorting and treatment can reduce the environmental footprint of MSW management by at least 10% in terms of leachate production and greenhouse gas emissions. Samples were collected using a randomized sampling …

Numerical Study On Enhancing The Geotechnical Behavior Of Strip Footings On Oil-Contaminated Sand Using Stone Columns, Ahmad Nasr, Waseim Azzam, Mohamed Ahmed Mahmoud Abdelrehem

Journal of Engineering Research

Ground improvement techniques are frequently employed in construction sites characterized by weak soil conditions that may result in suboptimal performance. The use of ordinary and encased stone columns aims to enhance endurance, shear strength, and soil hardness, thereby mitigating settlement issues and expediting the consolidation of contaminated sand soils. In this research, a comprehensive investigation involving 74 cases was conducted to assess the behavior of both ordinary stone columns and encased stone columns under strip footing in contaminated sand subgrade. The objective was to discern the impact and characteristics of encapsulation in comparison to encapsulated stone columns, employing a Finite …

Investigation Of Temperature, Solution Strength, And Applied Stress Effects On Cation Exchange Processes In Different Geosynthetic Clay Liner Products, Kendra Fuller

Master's Theses

An extensive laboratory test program was conducted to analyze and compare the cation exchange processes in three different varieties of sodium bentonite (Na-B) geosynthetic clay liners (GCLs) over increased conditioning durations up to 32 days and investigate the effects of temperature, solution strength, and applied stress. The goal of this test program was to establish whether the variables of temperature, solution strength, and applied stress improved or degraded the engineering properties of GCLs in laboratory testing and municipal solid waste (MSW) landfill applications. The GCLs were conditioned in liquids of increasing ionic strength, using deionized water and 2, 50, and …

Modeling The Influence Of Internal Factors On Vehicular Mobility Performance, Aziz Mdimi

Tanzania Journal of Engineering and Technology (TJET)

Traffic mobility is significantly influenced by road conditions and the internal factors governing vehicular performance. Internal factors play a crucial role in vehicular mobility, influencing vehicles operate and performance. While existing vehicular mobility models primarily address external factors, external factors such as governor, engine, gear train and differential unit remain underexplored. This study formulates a comprehensive model to address this gap, focusing on the internal components that affect vehicular mobility. The proposed model employs both analytical and numerical methods to derive transfer functions for these subsystems using Matrix Laboratory (MATLAB), aiming to capture the dynamic behavior of vehicles under various …

Base Case Shear-Wave Velocity Profiles And Non-Linear Material Property Models Of Local Site Conditions In South Carolina For Seismic Site Response Analyses, Ali Sedaghat Shirehjini

All Dissertations

This dissertation presents the development of base case small-strain shear-wave velocity ( ) profiles and non-linear materials property models of local site conditions in South Carolina for seismic site response analyses. The need to address South Carolina's seismic hazards is partly motivated by the 1886 Charleston earthquake (moment magnitude, M_w= 6.7 to 7.5). Required inputs for seismic site response analysis include profile down to a specified reference outcrop condition and non-linear material properties for each layer in the profile. Although firm rock (i.e., ≥ 2,500 ft/s) or hard rock (i.e., ≥ 9,850 ft/s) is commonly assumed for the …

Effect Of Waste Covid-19 Masks On Compaction Characteristics Of Silty-Clay Soil, Sydney K. Lawson

Honors College Theses

The present study aims to explore the effect of adding shredded waste Covid-19 masks to silty-clay soil on the soil’s compaction characteristics for beneficial use in embankment, the subgrade of roadways, or backfill. This was accomplished by using two different types of masks: blue surgical masks and KN95 masks. Both mask types were hand shredded into half-inch sections using safety-scissors. The maximum dry density (MDD) and optimum moisture content (OMC) are the two most important compaction characteristics, and they were determined by the Standard Proctor Compaction Test (ASTM D698 / AASHTO T99). The change of both the MDD and OMC …

The Use Of Repurposed Whole Textiles To Modify The Mechanical And Hydrogeological Properties Of Green Roof Media And Granular Soils, Angelis Almanzar-Chevalie, Yehya Elfgeeh, Calvin O. Walters Jr.

Publications and Research

This study investigates using repurposed whole textiles to modify the mechanical and hydrogeological properties of lightweight Green Roof media and granular pavement soils.

Green Roof Media Green roofs aim to bring the advantages of suburban agriculture to urban environments while improving energy efficiency and enhancing stormwater management in public, commercial, and residential buildings. Previous studies by City Tech undergraduate research assistants demonstrated significant modification in hydrogeological properties when incorporating textile fabric up to 3% textile by weight (%Tex) at an aspect ratio of 1:1. The effects of mixing repurposed whole textile fiber with Green Roof media is evaluated with regards …

Performance Assessment Of Microencapsulated Phase Change Materials With Low To High Thermoregulation Range In Asphalt Binder, Anil Kumar Baditha, Ayyaz Fareed

Graduate Student and Postdoctoral Fellow Symposium

Asphalt pavements face significant challenges due to low temperature cracking and rutting caused by extreme temperature fluctuations and traffic loading. These issues result in higher maintenance costs and reduced service life of the pavements. To address this, researchers explored the use of Microencapsulated Phase Change Materials (MPCMs) to induce thermoregulation in asphalt pavements. However, the existing research focused on high-temperature performance of binders, highlighting the need of research on evaluating the low-temperature performance. Therefore, the study aims to evaluate the impact of incorporating MPCMs on low to high temperature performance of binders. Three types of MPCMs were incorporated into asphalt …

Numerical Study Of Cone Penetration In Calcareous Sands: Investigating Cone Tip Resistance Correction Factors For Crushable Soils, Stephanie Michelle Hyder

Dissertations and Theses

The cone penetration test (CPT) is used to characterize the behavior and properties of soils, including the susceptibility to earthquake liquefaction triggering. The cone tip resistance relates to liquefaction susceptibility through relative density, where relative density is closely related to both cone tip resistance and liquefaction susceptibility. Currently, published methods of estimating liquefaction potential (i.e., cyclic resistance ratio) are based on silica sands and do not properly characterize calcareous sands. The measured cone tip resistance in calcareous sands is lower than in silica sands at the same relative density; this difference is generally attributed to the higher compressibility of calcareous …

Demystifying Utility Coordination: Understanding The Basics, Josshe I. Palm

Purdue Road School

This session will explain utility coordination to non-utility coordinators. It will help educate others about the role and responsibilities of a utility coordinator, an OSA, easy UC and design mistakes to avoid, scope and design considerations, items commonly overlooked, when to coordinate SUE, and how to work with your UC to request a letting adjustment. We will also highlight UC submittals and allow time for questions about the UC’s role in a project’s success.

Evaluation Of Hydrophobic Materials For Stabilizing Expansive Soils, Suman Shrestha

Civil Engineering Theses - Archive

The swelling and shrinkage of the expansive soil as a response to moisture change is one of the significant challenges posed to infrastructure projects. The significant economic damage that is caused by the expansive soil, as well as its abundance in nature, has prompted various scientists and engineers all around the world to actively search for new and improved methods for stabilizing it. Various traditional methods, such as lime and cement treatment, have been used extensively to stabilize expansive soils and mitigate their harmful effects on the infrastructure. Although these methods are quite often effective and various studies have been …