Civil Engineering Commons^™

The Study Of Effect Of Definite Grain Sized Sand On The Shearing Strength Of Clays, Faruk Omer Akkoseoglu

Masters Theses

"Slopes of all kinds, including mountains, hills, sea coast bluffs, river banks, and man made cuts and fills, stay in place only because of the shearing strength possessed by the soil or rock of which they are composed. The resistance of soils to shearing strength is probably the most important of all the soil properties to foundation engineers. Most of the serious structural failures which are due to unexpected soil behaviour are caused by deficiency in the shearing strength of the soil. Water, on the other hand, possesses no static strength in shear, therefore bodies of water have no surface …

Effects Of Sand Admixtures On The Physical Properties Of Soils, Necati Kanatsiz

Masters Theses

"The purpose of this study is to determine the effects of sand admixtures on the physical properties of soils. Soil may be defined as a heterogenous [sic] collection of rock and mineral fragments whose decomposition and disintegration have been brought about by the action of physical, chemical, and biological forces, working singly or in combination...In the conviction that the study of soils, with respect to highway engineering, is becoming more and more important this study was undertaken in order to learn whether the addition of sand would lead to desirable results, and if not, at least secure some further addition …

The Theory Of Limit Design As Applied To Column Analysis, John Francis Mccarthy

Masters Theses

"In any discussion of compression members of a structure, account has to be taken primarily of the relative "slenderness" or bending weakness of the member. If the member be so short that axial loading causes very slight deflection at any point throughout the member, it is usually designated a simple compression member and no account is taken of the additional stresses due to the deflection. When, however, the ratio of the length to the least radius of gyration of the member becomes so large that bending stresses cannot be ignored, the member is usually called a column and its consequent …

Velocity Studies In A Vertical Pipe Flowing Full, Robert Franklin Tindall

Masters Theses

"The purpose of this investigation is to install a hard drawn copper pipe approximately 1/2 inch in diameter, and approximately 35 feet long in a vertical position. The copper pipe is to have pressure takeoff points at various distances along the length of the pipe. The purpose of these takeoffs is to measure the pressure of the water at the point of takeoff in the pipe. The water is to be forced into the pipe, assisted by gravity, thereby causing a pressure of some measurable quanity [sic] greater than absolute zero pressure. The discharge was to be by volumetric measurement, …

Effect Of Removed Web-Section On Critical Load For I-Beam Columns, Henri Simon Rigo

Masters Theses

"This investigation deals with a series of column tests of aluminum I-sections which have a perforated web. Specifically, the tests show that the weight is decreased without decrease in strength. Several basic assumptions are made in the design of a column. The physical action of a column is idealized in the derivation of formulae which will predict within reasonable limits the load which the member will sustain. In a given installation of non-homogeneity of material, kinks, uneven bearing, lack of symmetry due to riveting or welding, stress concentration and many other disturbing factors not in agreement with these assumptions may …

Flood Control With Retarding Basin Type Reservoirs In Meramec Basin, Missouri, Ilhan Kaya Ozbilen

Masters Theses

"When rainfall occurs that provides more runoff than can be carried within the normal channels of existing streams a flood results. The excess water overflows the valley lands, invades developed areas, and causes destruction of property or, in extreme cases, loss of human life...Many structures are built to control water: Waterways of proper depth and width provide arteries of transportation; water controlled and discharged through water-wheels provides power; water may be caught in storage basins and distributed for irrigation or water supply; and water that is an actual or potential source of damage or danger to property or to human …

The Precipitation-Runoff Relationship On The Grand River Basin Of Missouri And Iowa, J. Kent Roberts

Masters Theses

"In the study of a drainage basin which is to be utilized for water supply or water power, there is frequently a dearth or complete lack of runoff data, though precipitation data are almost always available. The Water Resources Branch of the United States Geological Survey maintains gaging stations on various streams and runoff records from these streams are available from their publications and offices. Many of these runoff records cover a considerable number of years, and are entirely sufficient for use in an analysis of any drainage basin covered by such data. Some of these gaging stations have not …

A Comprehensive Traffic Survey Of Phelps County, Missouri, Clifford D. Muir

Masters Theses

"The purpose of this study is two fold. The first of these purposes is to serve as a pattern or guide for any county or township wishing to conduct a comprehensive traffic survey. The second purpose of this study is to provide traffic classification and other data on a typical county system of rural roads. Today, many counties in the United States are faced with the problem of inadequate roads, due to the modernization of the American farm. While they realize this problem exists, may county governments have developed no organized method of studying and determining their needs...When the author …

The Effect Of Calcium Chloride On Air-Entrained Concrete, Gerard Francis Hofstaedter

Masters Theses

"The essence of the problem is not fully set forth in the title in that all aspects are not covered. In this case, the term "effect" means how the compressive strength and the modulus of elasticity vary with the addition of calcium chloride...Many pages will be found concerning the relative merits of plain concrete versus air-entrained concrete. All phases of the problem have been covered thoroughly. Investigations have been conducted on both plain and air-entrained concrete to determine the compressive strength, flexural strength, durability and workability"--Introduction, page 1.

Effects Of Wave Action Upon The Design Of The Breakwater For Istanbul Harbor, Melih Suat Durusan

Masters Theses

"The city of Istanbul is situated on the southern entrance of the Bosphorus which separates Asia from Europe; at the same time it is the only strait that leads to the Black Sea. Istanbul is the city that connects Europe-Asia highways and railways. These features show that Istanbul is a very important port. The Golden Horn and the southern end of the Bosphorus constitute a natural harbor which has been in use for many years. Although the natural harbor has served its purpose in the past, the present conditions necessitate the presence of a new harbor...One economical method of improving …

A Survey To Determine The Most Economic Design For Concrete Runways Of A Class 4 Airport, Yani Triandafilidis

Masters Theses

"This study is for the purpose of determining the most economical design for the runways of the Yesilkoy airport in Istanbul, Turkey. The discussion will include different design methods for the runways and the longitudinal and transverse joints that will be used in each case to provide crack control in the runway surfacing.

The city of Istanbul has a population of about one million. It is a growing city, being the industrial center of Turkey, and it also serves as a terminal for transcontinental airway systems. For these reasons it was decided to construct a class 4 airport for the …

Calibration Of Weirs By Means Of Critical Flow And Specific Energy, Robert A. Rapp

Masters Theses

"For many years man has been relying more each day upon metering devices to measure the flow of fluids in industry. The orifice, orifice meter, venturi meter, pitot tube, nozzle, flume and the weir have been employed, each having its own particular advantage.

In this parade of metering progress, the contracted weir has long been the forgotten brother of the suppressed weir. In almost every textbook on hydraulics or fluid mechanics, the following words appear, "end contractions are to be avoided where the weir cannot be calibrated". This skepticism and the length or absurdity of some contracted weir formulas led …

The Effect Of Pressure Prehydration On The Strength Of Hydraulic Cement Concrete, Thomas Holmes Whitfield Jr.

Masters Theses

"It appears that the rapidity of curing and the degree or ultimate strength of concrete can be influenced by both chemical and physical factors. The main function of the physical factors involved seems to be the creating of a more intimate combination of the cement and water which are the active ingredients. For example, finer grinding of the cement would present more surface area to the water; the application of heat would decrease the amount of surface tension of the water, in addition to speeding the chemical reaction, steam under pressure would force water into the porous particles of cement; …

The Development Of Plans For A National Airport For Ankara, Turkey, Mehmet Ragip Samli

Masters Theses

"'The present rapid development of general interest in aviation has brought to the front a new field of engineering. Development of the airplane has already reached a stage where the limit of its usefulness seems fixed only by the places which may be provided for taking off and landing. Due to the newness of the problem, not every one on whom responsibility rests recognizes the fact that the selection of the proper site and location for an airport is just as much an engineering problem as are its design and construction.'

The Turkish government began construction or the Ankara-Esenboga airport …

Design And Construction Of Earth Dams., Panthragadi Bhyravamurthy

Electronic Theses and Dissertations

This thesis deals with the design and construction of rolled-fill earth dams with the standard methods of practice, taking the Hirakud Dam as the basis. The field operations of the investigation to obtain observational information and to secure samples for the laboratory testing include observation of rain gauge and river gauge readings, taking river water samples, digging test pits, drilling grout holes, opening drifts, digging borrow pits and conducting detailed topographical surveys. Laboratory tests are conducted on the samples and the results are plotted in graphs. Rainfall and run-off statistics are plotted in graphs. Observational information of geology is plotted …

Waterfront Construction In New York Harbor, Carman William Garrison

Theses

The following chapters are devoted to the various phases of that branch of construction which is followed from the offshore side of the waterfront. This branch, in the parlance of the building trades, is known as dockbuilding. Years ago all waterfront structures in New York Harbor were constructed almost entirely of timber and experience taught that the most economical approach for building docks and wharves was made by utilizing floating piledrivers and derricks. Thus it happened that dockbuilders became skilled both in the use of wood framing tools and in handling marine equipment. Modern dockbuilders must have, in addition to …

Recommended Procedure For The Computation Of Rights Of Way, Leon Hershkowitz

Professional Degree Theses

"This thesis sets forth a recommended procedure for the computation of areas included in "rights of way," using the principle of double meridian distances.

For a considerable number of years, it has been the opinion of the author that steps should be taken to arrive at some form of standardization in the procedures necessary in the computation of areas involving right of way and to more or less standardize legal descriptions pertaining thereto.

One need only examine the records of the various County Recorders in one particular state or in different states and he would be entirely convinced that such …

Research Investigation Of Seepage Control For Dams And Levees, Robert Raymond Brookshire

Professional Degree Theses

"The problems of a century old levee system have provided excellent research for the Corp of Engineers and others in the design and construction of earth dams for flood control, navigation and multi-purpose projects. A special problem on which valuable knowledge has been gained is that of seepage control. The experiences obtained in recent years have been supplemented by theoretical developments in the field of soil mechanics, but it is believed that considerable information will be gained on seepage control from further investigation and experience.

The safety factor to prevent failure from seepage is believed to be the most critical …

Design Of A Wind Tunnel For The Missouri School Of Mines And Metallurgy, William E. Speece

Masters Theses

"For some time there has been a need for a wind tunnel at the School of Mines for experimental work in the Civil and Mechanical Engineering Departments. With the expanding program and the possibility of establishing an Aeronautical Engineering School here, the need will be even more pronounced. So the problem will be of definite practical value. It was the original idea to design a small tunnel, build the tunnel, and to run a series of smoke tests on various structural models. However, after discussing the possibility of such a problem with school authorities, it was decided that if a …

Analysis Of The Transit Traverse Survey Method Of The United States Department Of Interior, Geological Survey, Edward John Kimmick

Masters Theses

"This thesis was undertaken to ascertain the feasibility of incorporating the United States Geological Survey methods of surveying and computing into a course of study in the Civil Engineering curriculum. It has been the author's opinion that a course of study could be tendered, as a definite project, which incorporates fundamental surveying and advanced surveying. The author's planned course of study was a method of third order transit traverse survey streamlining the method used by the United States Geological Survey. The time element and weather were the essential factors in the planning. In the advanced surveying course there are eighteen …

Efficiency Of Various Types Of Reinforcement In Controlling Opening Of Cracks In Concrete Pavements, Frederick Richard Heartz

Masters Theses

"To date very little work has been done on the subject of the amount of crack opening for different loads on concrete pavement. It is a known fact that these cracks must be held together sufficiently to have aggregate interlocking action if the pavement is to transfer loads from one edge of a crack to the other. The maximum permissable [sic] opening has been set at .027 inches by the Highway Research Board. The author has attempted in this investigations (1) to determine the effect of different spacing and different sizes of longitudinal and transverse wires in controlling crack opening …

The Establishment And Analysis Of A Triangulation System For The Teaching Of Advanced Surveying, Philip Blaine Newlin

Masters Theses

"The first thought of establishing a triangulation system for the University of Arizona student work was conceived early in the fall of 1947, when the author first learned that he would be in charge of the advanced surveying field parties during the spring semester. These men were to be instructed in the accepted manner of conducting surveys of higher order. This would include the measuring of a base line of second or first order accuracy, the turning of horizontal angles with this same degree of accuracy, the determination of the azimuth of the lines by astronomical observations, the running of …

Interrelationship Of Transverse Anchorage And Adhesive Bond In Welded Wire Reinforcement, Alan Arthur Becker

Masters Theses

"...Welded Wire Reinforcement Fabric has been applied only to certain "light types" of reinforced concrete construction. It has not as yet been applied as main tension reinforcement for most concrete structures, mainly due to the fact that a thorough investigation of the potentialities and possibilities of welded wire fabric has not as yet been conducted. It is expected that the data collected in this investigation coupled with data collected in similar investigations performed at the Missouri School of Mines and Metallurgy will furnish the basis for a structural and economic comparison between welded wire fabric and ordinary reinforcing bars. The …

Aerodynamic Research For An Improved Rotor Control System On Helicopters, Delmar Wallace Breuer

Masters Theses

"Since the author has always been interested in Aeronautical Engineering, and in particular, rotary-winged-aircraft, the problem of research for aerodynamic improvement of rotary-wing control systems was chosen. This problem was suggested by the Army Aircorps Officials of Wright-Patterson Field of Dayton, Ohio as being a valuable and practical problem for the government. It is also valuable and practical for the author since it follows his general course of undergraduate study and since it fits closely into the field for which he is preparing himself...The requirement with which the author is most concerned is the design system for the producing of …

A Correlation Of Formulas For The Flow Of Fluids In Pipes, John Gorman Duba

Masters Theses

"At present there exist two quite distinct fields in fluid flow in pipes, the one in water supply and the other in the petroleum industry. It is the purpose of this paper to discuss the various pipeline flow formulas as used in both fields and to correlate the exponential type formula which is much used in practice with the Nikuradse curves obtained in the laboratory"--A Brief Historical Review, page 5.

The Theory Of Limit Design As Applied To The Design Of A Continuous Beam Over Three Supports, Robert F. Davidson

Masters Theses

"The theory of Limit Design is the application of the theory of Plasticity to the estimation of the actual carrying capacity of a structure. In this theory, as it is applied to statistically indeterminate structures, the areas of most unfavorable stress are allowed to be stressed beyond the yield point and into the plastic range of stress. It was formerly held that, by assuming elastic behavior, all questions of strength of materials that concern the Structural Engineer were capable of solution. However, it is now becoming recognized, from actual measurements of deformations of structures and from tests carried to near …

A Study Rigid-Frame Design Versus Truss-And-Column Design, Stephen H. Goodman

University of the Pacific Theses and Dissertations

This paper describes the investigation of a mill building bent of truss and column design, a redesign using a rigid-frame, and an estimated cost of each design. For sake of brevity the overall design of the building (sway bracing, lateral bracing, purlins, girts, roofing, siding, and bay spacing) was assumed to be the same for both designs. It is possible that this assumption cannot be made and the estimates of cost, therefore, are in error. In actual practice the complete redesign of the building should be considered.

Standardization Of No-Passing Zone Pavement Markings, Glen Nickolas Hackmann

Professional Degree Theses

"This thesis is a comprehensive treatment of present methods practiced by the various Highway Departments in the United States. It presents in particular current methods used by the State Highway Departments and the Public Roads Administration in marking no-passing zones throughout the country. For a long time it has seemed to the author that such a study was needed by both students and highway engineers. Road-design information of great value has developed over the years and often has been published but never assembled in a single orderly presentation stripped of excessive overlapping"--Preface, page ii.

A Comprehensive Traffic Survey For The City Of Rolla, Phelps County, Missouri, Leon Hershkowitz

Masters Theses

"The ultimate aim of this comprehensive traffic survey for the city of Rolla, Phelps County, Missouri, is to furnish a guide or pattern together with the necessary forms, maps and charts, that can be followed and reproduced by any city having a population of less than 10,000 in a study to determine its particular traffic problems. This survey should serve as a guide in determining what corrective action can be taken in connection with the following: (1) The improvement of location of state highway trunk [sic] routes, by-pass routes, auxiliary routes, and county roads in the city's immediate area. (2) …

The Mechanical Anchorage Value Of The Transverse Wires In Welded Wire Reinforcement Fabric, Ernst August Weinel

Masters Theses

"The tests reported in this paper were performed in an effort to secure data concerning characteristic properties of Welded Wire Reinforcement Fabric. This fabric has been used, up to the present time, primarily for temperature reinforcement. Limited attention has been focused on its potentialities for use as main tension reinforcing steel, particularly concrete highway slabs and floor slab reinforcement for buildings. The manufacturers of the Welded Wire Reinforcement Fabric believe their product can be used to better advantage as main tension reinforcement in reinforced concrete structures both from an economic and structural viewpoint, than structural steel reinforcing bars"--Object of Research, …