Engineering Commons^™

Temperature Measurements During High Flux Ion Beam Irradiations, M. L. Crespillo, Joseph T. Graham, Y. Zhang, W. J. Weber

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

A systematic study of the ion beam heating effect was performed in a temperature range of -170 to 900 °C using a 10 MeV Au³⁺ ion beam and a Yttria stabilized Zirconia (YSZ) sample at a flux of 5.5 x 10¹² cm^-2 s^-1. Different geometric configurations of beam, sample, thermocouple positioning, and sample holder were compared to understand the heat/charge transport mechanisms responsible for the observed temperature increase. The beam heating exhibited a strong dependence on the background (initial) sample temperature with the largest temperature increases occurring at cryogenic temperatures and decreasing with increasing temperature. …

Strain Effects On The Work Function Of An Organic Semiconductor, Yanfei Wu, Annabel R. Chew, Geoffrey A. Rojas, Gjergji Sini, Greg Haugstad, Alex Belianinov, Sergei V. Kalinin, Hong Li, Chad Risko, Jean-Luc Brédas, Alberto Salleo, C. Daniel Frisbie

Chemistry Faculty Publications

Establishing fundamental relationships between strain and work function (WF) in organic semiconductors is important not only for understanding electrical properties of organic thin films, which are subject to both intrinsic and extrinsic strains, but also for developing flexible electronic devices. Here we investigate tensile and compressive strain effects on the WF of rubrene single crystals. Mechanical strain induced by thermal expansion mismatch between the substrate and rubrene is quantified by X-ray diffraction. The corresponding WF change is measured by scanning Kelvin probe microscopy. The WF of rubrene increases (decreases) significantly with in-plane tensile (compressive) strain, which agrees qualitatively with density …

Design Live Load Factor Calibration For Michigan Highway Bridges, Christopher D. Eamon, Valid Kamjoo, Kazuhiko Shinki

Civil and Environmental Engineering Faculty Research Publications

In this study, a reliability-based calibration of live load factors for bridge design specific to the State of Michigan was conducted. Two years of high frequency WIM data from 20 representative state-wide sites were analyzed, and load effects were generated for bridge spans from 6 to 122 m (20 to 400 ft), considering simple and continuous moments and shears, as well as single lane and two lane effects. Seventy-five year statistics for maximum live load were then estimated with probabilistic projection. Bridge girders considered for the calibration included composite steel, prestressed concrete, side-by-side and spread box beams, as well as …

Dynamic Transverse Debondong Of A Single S-2 Fiber, Stephen E. Levine

Open Access Theses

Fiber reinforced composites are becoming increasingly common due to their high strength to weight ratios as compared to more conventional materials. Along with this increased used comes the need to have a higher level of understanding of the material characteristics. Specifically, the interface between the fiber and matrix is of particular interest. Loss of adhesion at this interface, known as debonding, can greatly decrease material strength. There has been significant research into debdonding phenomena at low strain rates. However, there is still a need for further insight at higher strain rates. In addition, given the opacity of many epoxy resins, …

Supervised Learning-Based Explicit Nonlinear Model Predictive Control And Unknown Input Estimation In Biomedical Systems, Ankush Chakrabarty

Open Access Dissertations

Application of nonlinear control theory to biomedical systems involves tackling some unique and challenging problems. The mathematical models that describe biomedical systems are typically large and nonlinear. In addition, biological systems exhibit dynamics which are not reflected in the model (so-called 'un-modeled dynamics') and hard constraints on the states and control actions, which exacerbate the difficulties in designing model-based controllers or observers.

This thesis investigates the design of scalable fast explicit nonlinear model predictive controllers (ENMPCs). The design involves (i) the estimation of a feasible region using Lyapunov stability methods and support vector machines; and (ii) within the estimated feasible …

Analysis And Simulation Of Small Scale Microwave Interferometer Experiments On Non-Ideal Explosives, David E. Kittell

Open Access Dissertations

Small scale experiments for non-ideal and homemade explosives (HMEs) were investigated, analyzed, and subsequently modeled in an attempt to develop more predictive capabilities for the threat assessment of improvised explosive devices (IEDs), as well as to provide new analysis capabilities for other investigators in the field. Non-ideal explosives and HMEs are challenging to characterize because of the nearly limitless parameter space (e.g. sample composition, density, particle morphology, etc.) which gives rise to a broad range of explosive sensitivity and performance. Large scale tests, such as rate stick and gap tests, are not feasible for characterizing every HME of interest due …

Wind Plant System Engineering Through Optimization Of Layout And Yaw Control, Paul Fleming, Andrew Ning, Pieter Gebraad, Katherine Dykes

Faculty Publications

Recent research has demonstrated exciting potential for wind plant control systems to improve the cost of energy of wind plants. Wind plant controls seek to improve global wind plant performance over control systems in which each turbine optimizes only its individual performance by accounting for the way wind turbines interact through their wakes. Although these technologies can be applied to existing wind plants, it is probable that the maximum benefit would be derived by designing wind plants with these capabilities in mind. In this paper, we use system engineering approaches to perform coupled wind plant controls and position layout optimizations …

Hyperelastic Modeling Of Wide-Base Tire And Prediction Of Its Contact Stresses, Jaime Hernandez, Imad L. Al-Qadi

Civil and Environmental Engineering Faculty Research and Publications

Description of tire model development using the finite element (FE) method is presented. Three-dimensional tire-pavement contact stresses were predicted for braking, traction, and free rolling using the FE method. Measured load-deflection curves, contact area, and contact stresses were used for model outcome validation. Slide-velocity-dependent friction and accurate input regarding geometry and material properties were considered. The developed tire model, which helped in studying contact stresses variation in each direction, was used to explain the various phenomena taking place at the tire-pavement interface during straight-line rolling. The analysis matrix includes nine rolling conditions and various loads, tire inflation pressures, and speeds. …

Microbial Biofilm Development And Electron Transfer In Electrochemical Systems, Jose Cornejo

Chemical and Biological Engineering ETDs

Energy harvesting from microorganisms has created vibrant research efforts for the past 20 years that has lead to the development of emerging topics such as microbial electrochemistry, biofilm formation in electrochemical systems and alternative energy technologies applied in environmental processes. In this study we present procedures that aim for further understanding of bacterial physiological conditions in electrochemical systems and interactions between biofilms and solid surfaces, particularly, for the facultative anaerobe Shewanella oneidensis MR-1. These systems consist of microbial fuel cells (MFCs) whose anode component will be evaluated with regards to performance, electrical current generation, and microbial coverage and biofilm development. …

Error-Compensation Method For Inclination Measurement Under The Influence Of The Dynamic Interference, Yanshun Zhang, Yajing Guo, Kui Li, Chaoying Pei, Ming Li

Mechanical and Aerospace Engineering Faculty Research & Creative Works

To deal with the problem of the inclination measurement errors caused by the dynamic motions, such as rotational and accelerated rectilinear components, this paper puts forward an effective inclination measurement scheme and the corresponding error-compensation method based on one accelerometer and two gyroscopes. In addition, the principal prototype of the dynamic inclination measurement apparatus is set up to conduct experiments of turntable rotation test, trolley test, and the turntable sway test at different inclined angles, thus verifying the feasibility of the error-compensation method under the effects of the rotational motion, accelerated rectilinear motion or both motions at the same time. …

The Structural Properties Of Ingan Alloys And The Interdependence On The Thermoelectric Behavior, Bahadir Kucukgok, Xuewang Wu, Xiaojia Wang, Zhiqiang Liu, Ian T. Ferguson, Na Lu

Electrical and Computer Engineering Faculty Research & Creative Works

The III-Nitrides are promising candidate for high efficiency thermoelectric (TE) materials and devices due to their unique features which includes high thermal stability. A systematic study of the room temperature TE properties of metalorganic chemical vapor deposition grown InxGa1-xN were investigated for x = 0.07 to 0.24. This paper investigated the role of indium composition on the TE properties of InGaN alloys in particular the structural properties for homogenous material that did not show significant phase separation. The highest Seebeck and power factor values of 507 μV K^-1 and 21.84 x 10^-4 Wm^-1K^-1 were observed, …

Daylighting And Thermo-Electrical Performance Of An Autonomous Suspended Particle Device Evacuated Glazing, Aritra Ghosh

Doctoral

Suspended particle device (SPD) glazing is an AC powered switchable glazing. PV powered SPD evacuated (vacuum) glazing was proposed with the potential of reducing the heating demand, cooling demand and artificial lighting demand of a building. To achieve an autonomous SPD vacuum glazing, semi empirical simulation and outdoor characterisation was explored in this thesis. Transmission of SPD glazing (area 0.058 m2) varied from 5% when opaque to 55% when transparent in the presence of 110 V, 0.07 W AC supply was characterised in outdoor test cell in Dublin. The SPD glazing has variable spectral transmission in the presence of variable …

The Influence Of Season, Heating Mode And Slope Angle On Wildland Fire Behavior, Jonathan R. Gallacher

Theses and Dissertations

Wildland fire behavior research in the last 100 years has largely focused on understanding the physical phenomena behind fire spread and on developing models that can predict fire behavior. Research advances in the areas of live-fuel combustion and combustion modeling have highlighted several weaknesses in the current approach to fire research. Some of those areas include poor characterization of solid fuels in combustion modeling, a lack of understanding of the dominant heat transfer mechanisms in fire spread, a lack of understanding regarding the theory of live-fuel combustion, and a lack of understanding regarding the behavior of flames near slopes. In …

Arctic Sea Ice Classification And Soil Moisture Estimation Using Microwave Sensors, David Brian Lindell

Theses and Dissertations

Spaceborne microwave sensors are capable of estimating various properties of many geophysical phenomena, including the age and extent of Arctic sea ice and the relative soil moisture over land. The measurement and classification of such geophysical phenomena are used to refine climate models, localize and predict drought, and better understand the water cycle. Data from the active Ku-band scatterometers, the Quick Scatterometer (QuikSCAT), and the Oceansat-2 Scatterometer (OSCAT), are here used to classify areas of first-year and multiyear Arctic sea ice using a temporally adaptive threshold on reported radar backscatter values. The result is a 15-year data record of daily …

Tu-Pod: Safety Review, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Tu-POD: Safety Review" from February of 2016.

The Effect Of Biofilm Carrier Length On Nitrification In Moving Bed Biofilm Reactors: An Examination Of Mixing Intensity, Shock Loadings, And Ph Changes, Kody Garcia

Civil Engineering ETDs

Biofilms grown on free-floating attachment surfaces, as in integrated fixed film activated sludg (IFAS) and moving bed bioreactors (MBBRs) are commonly used in wastewater treatment, but little is known about how media geometry affects the biofilms and process performance. The objective of this study was to compare nitrification and growth of biofilms grown on different length media in bench-scale MBBRs. The carriers were cut from high density polyethylene tubing with one media type one-third the length of the other, but with inner and outer diameter dimensions identical. Each bioreactor was continuously operated with coarse bubble aeration and provided with a …

Traffic Safety Primer For Local Agencies, Laura Slusher, Michigan Ltap

Indiana Local Technical Assistance Program (LTAP) Publications

The purpose of this booklet is to empower local agency personnel to make informed decisions that can improve roadway safety in your community. By identifying and addressing potential roadway hazards, you can reduce the likelihood of a future traffic crash for your community and your family. Adapted by permission from the Michigan LTAP’s 2008 Publication What Elected Officials Need to Know About Traffic Safety (And What YOUR Constituents Expect YOU to Know!) This is an update of the 2014 version and includes a section on roadway departure crashes.

Level Of Effort For Indiana Counties, Indiana Ltap

Indiana Local Technical Assistance Program (LTAP) Publications

This report is based on 2014 calendar year information retrieved from the Indiana Tax Handbook, County Operations Reports, information provided from the Indiana State Auditor’s office regarding County Distributions, and information from Indiana Gateway for Government Units.

Pipe Express®, Purdue Ect Team

ECT Fact Sheets Archive

By developing Pipe Express^® Herrenknecht AG has set new standards for installing pipelines. With this system, no groundwater lowering is necessary and, in comparison with the open construction method, routes can be considerably narrower. This has a positive effect on construction costs. Because it is highly ecological and cost-efficient procedure, the development of this new system is being subsidized by the German Environment Ministry.

The Pipe Express^® technology combines the advantages of trenchless installations and open-cut solutions. Pipe Express^® can be used in any kind of soft to medium formations. However, the technology exhibits its major benefits …

A Comprehensive Python Toolkit For Harnessing Cloud-Based High-Throughput Computing To Support Hydrologic Modeling Workflows, Scott D. Christensen

Theses and Dissertations

Advances in water resources modeling are improving the information that can be supplied to support decisions that affect the safety and sustainability of society, but these advances result in models being more computationally demanding. To facilitate the use of cost- effective computing resources to meet the increased demand through high-throughput computing (HTC) and cloud computing in modeling workflows and web applications, I developed a comprehensive Python toolkit that provides the following features: (1) programmatic access to diverse, dynamically scalable computing resources; (2) a batch scheduling system to queue and dispatch the jobs to the computing resources; (3) data management for …

Perforated Hollow Core Waveguides For Alkali Vapor-Cells And Slow Light Devices, Matthieu C. Giraud Carrier

Theses and Dissertations

The focus of this work is the integration of alkali vapor atomic vapor cells into common silicon wafer microfabrication processes. Such integrated platforms enable the study of quantum coherence effects such as electromagnetically induced transparency, which can in turn be used to demonstrate slow light. Slow and stopped light devices have applications in the optical communications and quantum computing fields. This project uses hollow core anti-resonant reflecting optical waveguides (ARROWs) to build such slow light devices. An explanation of light-matter interactions and the physics of slow light is first provided, as well as a detailed overview of the fabrication process. …

Microfluidic Devices And Biosensors, Long-Fang Tsai

Theses and Dissertations

My research broadly covers various important aspects of microfluidic devices and biosensors. Specifically, this dissertation reports: (1) a new and effective room temperature method of bonding polydimethylsiloxane (PDMS) microfluidics to substrates such as silicon and glass, (2) a new microfluidic pump concept and implementation specifically designed to repeatedly drive a small sample volume (<1 µL) very rapidly (~500 µL/min) through a sensor-containing flow channel to significantly decrease sensor response time through advection-driven rather than diffusion-driven mass transport, (3) use of a new microfluidic material based on polyethylene glycol diacrylate (PEGDA) to implement impedance-based dynamic nanochannel sensors for protein sensing, and (4) an investigation of galvanoluminescence and how to avoid it for conditions important to fluorescence-based dielectrophoresis (DEP) microfluidic biosensors. Over the last decade, the Nordin research group has developed a lab-on-a-chip (LOC) biosensor based on silicon photonic microcantilever arrays integrated with polydimethylsiloxane (PDMS) microfluidics for protein biomarker detection. Integration requires reliable bonding at room temperature with adequate bond strength between the PDMS element and microcantilever sensor substrate. The requirement for a room temperature process is particularly critical because microcantilevers must be individually functionalized with antibody-based receptor molecules prior to bonding and cannot withstand significant heating after functionalization. I developed a new room temperature bonding method using PDMS curing agent as an intermediate adhesive layer. Two curing agents (Sylgard 184 and 182) were compared, as well as an alternate UV curable adhesive (NOA 75). The bond strength of Sylgard 184 was found to be stronger than Sylgard 182 under the same curing conditions. Overnight room temperature curing with Sylgard 184 yields an average burst pressure of 433 kPa, which is more than adequate for many PDMS sensor devices. In contrast, UV curable epoxy required a 12 hour bake at 50 °C to achieve maximum bond strength, which resulted in a burst pressure of only 124 kPa. In many biosensing scenarios it is desirable to use a small sample volume (<1 µL) to detect small analyte concentrations in as short a time as possible. I report a new microfluidic pump to address this need, which we call a reflow pump. It is designed to rapidly pump a small sample volume back and forth in a flow channel. Ultimately, the flow channel would contain functionalized sensor surfaces. The rapid flow permits use of advection-driven mass transport to the sensor surfaces to dramatically reduce sensor response times compared to diffusion-based mass transport. Normally such rapid flow would have the effect of decreasing the fraction of analyte molecules in the volume that would see the sensor surfaces. By configuring the pump to reflow fluid back and forth in the flow channel, the analyte molecules in the small sample volume are used efficiently in that they have many opportunities to make it to the sensor surfaces. I describe a 3-layer PDMS reflow pump that pumps 300 nL of fluid at 500 µL/min for 15 psi actuation pressure, and demonstrate a new two-layer configuration that significantly simplifies pump fabrication. Impedance-based nanochannel sensors operate on the basis of capturing target molecules in nanochannels such that impedance through the nanochannels is increased. While simple in concept, the response time can be quite long (8~12 hours) because the achievable flow rate through a nanochannel is very limited. An approach to dramatically increase the flow rate is to form nanochannels only during impedance measurements, and otherwise have an array of nanotrenches on the surface of a conventional microfluidic flow channel where they are exposed to normal microfluidic flow rates. I have implemented such a dynamic nanochannel approach with a recently-developed microfluidic material based polyethylene glycol diacrylate (PEGDA). I present the design, fabrication, and testing of PEGDA dynamic nanochannel array sensors, and demonstrate an 11.2 % increase in nanochannel impedance when exposed to 7.2 µM bovine serum albumin (BSA) in phosphate buffered saline (PBS). Recently, LOC biosensors for cancer cell detection have been demonstrated based on a combination of dielectrophoresis (DEP) and fluorescence detection. For fluorescence detection it is critical to minimize other sources of light in the system. However, reported devices use a non-noble metal electrode, indium tin oxide (ITO), to take advantage of its optical transparency. Unfortunately, use of non-noble metal electrodes can result in galvanoluminescence (GL) in which the AC voltage applied to the electrodes to achieve DEP causes light emission, which can potentially confound the fluorescence measurement. I designed and fabricated two types of devices to examine and identify conditions that lead to GL. Based on my observations, I have developed a method to avoid GL that involves measuring the impedance spectrum of a DEP device and choosing an operating frequency in the resistive portion of the spectrum. I also measure the emission spectrum of twelve salt solutions, all of which exhibited broadband GL. Finally, I show that in addition to Au, Cr and Ni do not exhibit GL, are therefore potentially attractive as low cost DEP electrode materials.

Relativistic Backyard Wave Oscillator With A Gaussian Radiation Pattern Related Technologies, Ahmed Elfrgani

Electrical and Computer Engineering ETDs

Short pulse high power microwave (HPM) devices with Gaussian radiation pattern are attractive for many applications. The importance of the Gaussian microwave beam is that its maximum energy density is concentrated on axis. The purpose of this study is to use a backward wave oscillator (BWO), which is typically known to radiate in the TM01 mode, to produce an HPM Gaussian wave beam. A BWO generates an electromagnetic wave with negative group velocity where the wave is traveling in the direction opposite to the electron beam. Thus, to extract the microwave signal axially, a cavity resonator reflector or cutoff waveguide …

Glucocorticoid Cell Priming Enhances Transfection Outcomes In Adult Human Mesenchymal Stem Cells, Abby M. Kelly, Sarah A. Plautz, Janos Zempleni, Angela K. Pannier

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Human mesenchymal stem cells (hMSCs) are one of the most widely researched stem cell types with broad applications from basic research to therapeutics, the majority of which require introduction of exogenous DNA. However, safety and scalability issues hinder viral delivery, while poor efficiency hinders nonviral gene delivery, particularly to hMSCs. Here, we present the use of a pharmacologic agent (glucocorticoid) to overcome barriers to hMSC DNA transfer to enhance transfection using three common nonviral vectors. Glucocorticoid priming significantly enhances transfection in hMSCs, demonstrated by a 3-fold increase in efficiency, 4–15-fold increase in transgene expression, and prolonged transgene expression when compared …

Full-Scale Shake Table Cyclic Simple Shear Testing Of Liquefiable Soil, Jasper Stanford Jacobs

Master's Theses

This research consists of full-scale shake table tests to investigate liquefaction of sandy soils. Consideration of the potential and consequences of liquefaction is critical to the performance of any structure built in locations of high seismicity underlain by saturated granular materials as it is the leading cause of damage associated with ground failure. In certain cases the financial losses associated with liquefaction can significantly impact the financial future of an entire region.

Most liquefaction triggering studies are performed in the field where liquefaction has been previously observed, or in tabletop laboratory testing. The study detailed herein is a controlled laboratory …

Inversion Characteristics Of A Buoyant Cylindrical Puck During Oblique Water Impact, Zachary Crawford Smith

Theses and Dissertations

The Apollo Command Module had a tendency to flip over upon impact with the ocean surface after returning from space (9/19 times). In an effort to better characterize the inversion process for future water landing vehicles, experimental results for a simplified buoyant cylindrical puck impacting the water surface are presented. This study focuses on the dependence of inversion upon vertical velocity, horizontal velocity, and the pitch angle of the puck relative to the free surface. High-speed images reveal an asymmetric cavity that forms upon water impact. The asymmetric cavity then collapses, applying a moment, which can be sufficient to invert …

Can The Gulf Stream Induce Coherent Short-Term Fluctuations In Sea Level Along The Us East Coast?: A Modeling Study, Tal Ezer

CCPO Publications

Much attention has been given in recent years to observations and models that show that variations in the transport of the Atlantic Meridional Overturning Circulation (AMOC) and in the Gulf Stream (GS) can contribute to interannual, decadal, and multi-decadal variations in coastal sea level (CSL) along the US East Coast. However, less is known about the impact of short-term (time scales of days to weeks) fluctuations in the GS and their impact on CSL anomalies. Some observations suggest that these anomalies can cause unpredictable minor tidal flooding in low-lying areas when the GS suddenly weakens. Can these short-term CSL variations …

Maintenance Implications For Unmanned Aerial Vehicles In Remote Locations, Ian R. Mcandrew, Mark Kaintz, Andrew Carruthers

Publications

Maintenance in the aviation industry has evolved considerably since commercial and general aviation became a modern mode of transportation. ICAO has made maintenance a top priority by directing local National Aviation Authorities, NAA, to have implemented, robust and standardized training and qualifications for all maintenance personnel that work on any safety critical structure or component. There are rules, law and standards that are audited and the aviation industry is, perhaps, the most successful industry in maintaining standards and reliability. With the advent of Unmanned Aerial Vehicles, UAV, the role of maintenance is now needing to be reviewed to determine how …

Lift & Drag Reductions On Iced Wings During Take Off And Landing With Unmanned Aerial Vehicles, Ian R. Mcandrew

Publications

This research paper addresses an novel problem that has not been addressed in detail for many decades. Ice formation on aircraft has procedures and protocols to deal with expected and actual problems. Complex modern aircraft are equipped with a variety of techniques to remove Ice formation on an aircraft, especially the wings. The introduction of Unmanned Aerial Vehicles has added an old problem, that of low speed and the lack of power to overcome losses in lift through ice formation. In this research the different types of Ice formation, how they combine and affect Lift and Drag are also addresses …

Glide Effects On Low Speed Unmanned Aerial Vehicles With Ice Formation, I. Mcandrew, K. Witcher, E. Navarro

Publications

This paper builds on the research that was previously presented and defended at a conference and adds to the depth of glide characteristics and aerodynamics. The basic assumed theory of low speed flight is used as the starting point and determined if this holds true for low speed. Traditionally, flight has always been about achieving faster and high flight operations. Unmanned Aerial Vehicles (UAV) are not typically designed to fly fast, the construction and power units are limiting, added to the lack of complexity in propulsion systems prevents high speeds in most cases. Here, aerodynamic data for Ice on leading …