Engineering Commons^™

Numerical Modeling Of Virus Transport Through Unsaturated Porous Media, Kandala Rajsekhar, Pramod Kumar Sharma, Sanjay K. Shukla

Research outputs 2014 to 2021

This paper describes the movement of virus in one-dimensional unsaturated porous media. The governing virus transport equations consider the inactivation in liquid phase, liquid–solid interface, air–liquid interface, and sorption in both liquid–solid and air–liquid interfaces. Finite-volume method has been used for solving the advection and dispersion processes of the virus transport equation. The effects of transport parameters on virus concentration profiles have been investigated for virus present in liquid phase, adsorbed liquid–solid and liquid–air phases. The results show that the movement of viruses in three phases is affected by soil moisture, inactivation rate, pore velocity, and mass transfer coefficients. It …

Robust Bi-Directional Continuous Electrowetting Based On Metal-Semiconductor (M-S) Diodes, Qi Ni, Daniel E. Capecci, Millicent Schlafly, Nathan B. Crane

Faculty Publications

We demonstrate bi-directional continuous electrowetting by embedding metal-semiconductor diodes in the electrowetting substrate. Unlike conventional electrowetting on dielectric (EWOD), bi-directional continuous electrowetting uses a single electrode pair to actuate a droplet through long distances. As long as the voltage potential is maintained between two end electrodes, the droplet moves toward the electrode with the higher potential. However, previously reported material systems had limited success in repeated actuation. In this work, diodes based on Schottky barriers were fabricated by forming metal-semiconductor junctions between titanium and high resistivity n-type silicon. The performance enhancements were evaluated using current-voltage measurements of interface pairs. When …

Design, Testing And Evaluation Of Robotic Mechanisms And Systems For Environmental Monitoring And Interaction, James K. Higgins

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Unmanned Aerial Vehicles (UAVs) have significantly lowered the cost of remote aerial data collection. The next generation of UAVs, however, will transform the way that scientists and practitioners interact with the environment. In this thesis, we address the challenges of flying low over water to collect water samples and temperature data. We also develop a system that allows UAVs to ignite prescribed fires. Specifically, this thesis contributes a new peristaltic pump designed for use on a UAV for collecting water samples from up to 3m depth and capable of pumping over 6m above the water. Next, temperature sensors and their …

Height And Pressure Test For Improving Spray Application, Anna Siebe, Joe D. Luck

UCARE: Research Products

Pesticide application in agricultural fields affects a little over a million acres each year (USDA 2012). Current spray application equipment can automatically adjust nozzle flow rates in reaction to speed changes to maintain consistent application rates across the field. Uniform distribution of pesticides from the spray boom is critical to ensure proper crop care while minimizing negative environmental effects. Boom pressure and height are two primary factors that affect proper spray uniformity; however information on the combined effects of these factors are limited. The goal of this study was to provide end users with quantified data regarding the effects of …

Exploring Dynamic Memory Allocations For Bioinformatics Applications, Nitya Kovur

School of Computing: Dissertations, Theses, and Student Research

The progression of scientific data leads to an increase in the demand of powerful high performance computers (HPC) where data can be stored and analyzed. High performance computing is used in several research areas to solve large problems. However, efficient usage of supercomputing resources that are available is a major concern for most of the researchers. The user has to choose the amount of resources needed for execution before submitting the job. Over or under subscription of resources leads to low system utilization and/or low user satisfaction.

Bioinformatics is one such field that heavily relies on HPC. One of the …

Activity Analysis Of Spectator Performer Videos Using Motion Trajectories, Anish Timsina

School of Computing: Dissertations, Theses, and Student Research

Spectator Performer Space (SPS) is a frequently occurring crowd dynamics, composed of one or more central performers, and a peripheral crowd of spectators. Analysis of videos in this space is often complicated due to occlusion and high density of people. Although there are many video analysis approaches, they are targeted for individual actors or low-density crowd and hence are not suitable for SPS videos. In this work, we present two trajectory-based features: Histogram of Trajectories (HoT) and Histogram of Trajectory Clusters (HoTC) to analyze SPS videos. HoT is calculated from the distribution of length and orientation of motion trajectories in …

Eventflowslicer: A Goal-Based Test Case Generation Strategy For Graphical User Interfaces, Jonathan Saddler

School of Computing: Dissertations, Theses, and Student Research

Automated test generation techniques for graphical user interfaces include model-based approaches that generate tests from a graph or state machine model of the interface, capture-replay methods that require the user to specify and demonstrate each test case individually, and modeling-language approaches that provide templates for abstract test cases. There has been little work, however, in automated goal-based testing, where the goal is a realistic user task, a function, or an abstract behavior. Recent work in human performance regression testing (HPRT) has shown that there is a need for generating multiple test cases that execute the same user task in different …

Development And Initial Validation Of A Surgical Instrument For In Situ Mechanical Characterization Of Surgical Mesh-Tissue Composites, Jorge Ivan Hernandez Sanchez

All Theses

Approximately 5 million Americans have an abdominal wall hernia, and over 700,000 undergo surgical procedures every year to treat them. Surgical procedures have evolved with the goal of preventing recurrences, leading to the current gold standard of treatment: hernia repair with mesh. Hernia repair with mesh consists on augmenting the weakened abdominal wall by implanting a synthetic or biological mesh. Although the adoption of hernia repair with mesh has improved outcomes, recurrence from primary repair procedures with large incisions (>10 cm) remains an alarming 32%.

The wide variety of implanted surgical mesh (materials, structure) and surgical variability (attachment method, …

Rare Earth Emissions From Polyethylene Terephthalate Fiber, Joshua Jenkins Furtick

All Theses

Rare earth-polymer blends can be useful in many applications including safety, security, displays, and novelty. Polyester, specifically polyethylene terephthalate, is a ubiquitous material in the world today and offers many opportunities for the usefulness of visible light rare earth emissions.

In this work we have attempted to incorporate rare earth complexes with polyester yarn using various methods including coating, extrusion, and dyeing, with the latter having the most success. Nanoparticles were used initially for these experiments, however certain limitations of the particles could not be overcome, for example the size of the particles and the incompatibility of the inorganic matrix …

A Novel Particle Filtering Method For Estimation Of Pulse Pressure Variation During Spontaneous Breathing, Sunghan Kim, Fouzia Noor, Mateo Aboy, James Mcnames

Electrical and Computer Engineering Faculty Publications and Presentations

Background: We describe the first automatic algorithm designed to estimate the pulse pressure variation ([Formula: see text]) from arterial blood pressure (ABP) signals under spontaneous breathing conditions. While currently there are a few publicly available algorithms to automatically estimate [Formula: see text] accurately and reliably in mechanically ventilated subjects, at the moment there is no automatic algorithm for estimating [Formula: see text] on spontaneously breathing subjects. The algorithm utilizes our recently developed sequential Monte Carlo method (SMCM), which is called a maximum a-posteriori adaptive marginalized particle filter (MAM-PF). We report the performance assessment results of the proposed algorithm on …

Framework For Incorporating Probabilistic Building Performance In The Assessment Of Community Seismic Resilience, Henry V. Burton, Gregory Deierlein, David Lallemant, Ting Lin

Civil and Environmental Engineering Faculty Research and Publications

A framework is presented for incorporating probabilistic building performance limit states in the assessment of community resilience to earthquakes. The limit states are defined on the basis of their implications to postearthquake functionality and recovery. They include damage triggering inspection, occupiable damage with loss of functionality, unoccupiable damage, irreparable damage, and collapse. Fragility curves are developed linking earthquake ground motion intensity to the probability of exceedance for each of the limit states. A characteristic recovery path is defined for each limit state on the basis of discrete functioning states, the time spent within each state, and the level of functionality …

Delay-Independent Stability Analysis Of Linear Time-Delay Systems Based On Frequency, Xianwei Li, Huijun Gao, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies strong delay-independent stability of linear time-invariant systems. It is known that delay-independent stability of time-delay systems is equivalent to some frequency-dependent linear matrix inequalities. To reduce or eliminate conservatism of stability criteria, the frequency domain is discretized into several sub-intervals, and piecewise constant Lyapunov matrices are employed to analyze the frequency-dependent stability condition. Applying the generalized Kalman–Yakubovich–Popov lemma, new necessary and sufficient criteria are then obtained for strong delay-independent stability of systems with a single delay. The effectiveness of the proposed method is illustrated by a numerical example.

Evaluation Of Various Turbulence Models For Shock-Wave Boundary Layer Interaction Flows, Francis K. Acquaye

McKelvey School of Engineering Graduate Student Theses & Dissertations

Despite the modeling capabilities of current computational fluid dynamics (CFD), there still exist problems and inconsistencies in simulating fluid flow in certain flow regimes. Most difficult are the high-speed transonic, supersonic and hypersonic wall-bounded turbulent flows with small or massive regions of separation. To address the problem of the lack of computational accuracy in turbulence modeling, NASA has established the Turbulence Modeling Resource (TMR) website and has issued the NASA 40% Challenge. The aim of this challenge is to identify and improve/develop turbulence and transition models as well as numerical techniques to achieve a 40% reduction in the predictive error …

Application Of Genetic Algorithm In Multi-Objective Optimization Of An Indeterminate Structure With Discontinuous Space For Support Locations, Rahat Sultana

Masters Theses

In this thesis, an indeterminate structure was developed with multiple competing objectives including the equalization of the load distribution among the supports while maximizing the stability of the structure. Two different coding algorithms named “Continuous Method” and “Discretized Method” were used to solve the optimal support locations using Genetic Algorithms (GAs). In continuous method, a continuous solution space was considered to find optimal support locations. The failure of this method to stick to the acceptable optimal solution led towards the development of the second method. The latter approach divided the solution space into rectangular grids, and GAs acted on the …

A Transcutaneous Data And Power Transfer System For Osteogenesis Monitoring Sensors, Deepak Dileepkumar

Masters Theses

Implant devices are widely used in health care applications such as life support systems, patient rehabilitation devices and patient monitoring devices. Medical implants have enabled physicians to obtain relevant real time information regarding an organ, or a site of interest with in the body and suggest treatment accordingly. In some cases, the position of the implant within the body or threats of infections prevents wired communication techniques to extract information from the implant. Wireless communication is the alternative in such cases. Distraction osteogenesis is one such application where wireless communication can be established with callus growth monitoring sensors to obtain …

Asynchronous Data Processing Platforms For Energy Efficiency, Performance, And Scalability, Liang Men

Graduate Theses and Dissertations

The global technology revolution is changing the integrated circuit industry from the one driven by performance to the one driven by energy, scalability and more-balanced design goals. Without clock-related issues, asynchronous circuits enable further design tradeoffs and in operation adaptive adjustments for energy efficiency. This dissertation work presents the design methodology of the asynchronous circuit using NULL Convention Logic (NCL) and multi-threshold CMOS techniques for energy efficiency and throughput optimization in digital signal processing circuits. Parallel homogeneous and heterogeneous platforms implementing adaptive dynamic voltage scaling (DVS) based on the observation of system fullness and workload prediction are developed for balanced …

Channel Estimation Overhead Reduction For Downlink Fdd Massive Mimo Systems, Abderrahmane Mayouche

Graduate Theses and Dissertations

Massive multiple-input multiple-output (MIMO) is the concept of deploying a very large number of antennas at the base stations (BS) of cellular networks. Frequency-division duplexing (FDD) massive MIMO systems in the downlink (DL) suffer significantly from the channel estimation overhead. In this thesis, we propose a minimum mean square error (MMSE)-based channel estimation framework that exploits the spatial correlation between the antennas at the BS to reduce the latter overhead. We investigate how the number of antennas at the BS affects the channel estimation error through analytical and asymptotic analysis. In addition, we derive a lower bound on the spectral …

Evaluating A Measure-Calculate Method For Determining Sediment Oxygen Demand In Lakes, Adrian Beirise

Graduate Theses and Dissertations

A steady-state mass diffusion model used with simple measurable and calculable inputs for determining sediment oxygen demand (SOD) is compared to an intact core incubation (ICI) SOD method using samples from three lakes. The mass diffusion model coupled with inputs is known as the measure-calculate method (M-C) and is a potential alternative to existing methods for measuring SOD which are more complex, time-consuming, and costly. The M-C method requires inputs for volumetric sediment oxygen uptake (Ṅsed), sediment density and porosity, and water properties. Ṅsed was determined by suspending sediment in oxygen-saturated water with a DO probe and determining the steady …

Modeling Economic Impacts Of The Inland Waterway Transportation System, Furkan Oztanriseven

Graduate Theses and Dissertations

The inland waterway transportation system of the United States (U.S.) handles 11.7 billion tons of freight annually and connects the heartland of the U.S. with the rest of the world by providing a fuel-efficient and environmentally friendly mode of transportation. This dissertation aims to create decision support tools for maritime stakeholders to measure the economic impacts of the inland waterway transportation systems under real world scenarios including disruptions, demand changes, port expansion decisions, and channel deepening investments. Monte Carlo simulation, system dynamics, discrete-event simulation, agent-based modeling, and multiregional input-output modeling techniques are utilized to analyze the complex relationships between inland …

Modeling And Simulation Of 1700 V 8 A Genesic Superjunction Transistor, Staci E. Brooks

Graduate Theses and Dissertations

The first-ever 1.7kV 8A SiC physics-based compact SPICE model is developed for behavior prediction, modeling and simulation of the GeneSiC “Super” Junction Transistor. The model implements Gummel-Poon based equations and adds a quasi-saturation collector series resistance representation from a 1.2 kV, 6 A SiC bipolar junction transistor model developed in Hangzhou, China. The model has been validated with the GA08JT17-247 device data representing both static and dynamic characteristics from GeneSiC. Parameter extraction was performed in IC-CAP and results include plots showing output characteristics, capacitance versus voltage (C-V), and switching characteristics for 25 °C, 125 °C, and 175 °C temperatures.

Incorporating A New Class Of Uncertainty In Disaster Relief Logistics Planning, Emre Kirac

Graduate Theses and Dissertations

In recent years, there has been a growing interest among emergency managers in using Social data in disaster response planning. However, the trustworthiness and reliability of posted information are two of the most significant concerns, because much of the user-generated data is initially not verified. Therefore, a key tradeoff exists for emergency managers when considering whether to incorporate Social data in disaster planning efforts. By considering Social data, a larger number of needs can be identified in a shorter amount of time, potentially enabling a faster response and satisfying a class of demand that might not otherwise be discovered. However, …

Total Temperature Measurement At Pulse Detonation Engine Exhaust, Ninad Ramesh Kawle

Mechanical and Aerospace Engineering Theses - Archive

Pulse detonation engines (PDEs) are being studied in recent years as a potential means of power production. In PDEs, a supersonically travelling detonation wave traverses through the detonation tube. Total temperature of the exhaust of the PDE is not a well-known parameter. The objective of the research was to calibrate and employ miniature type E thermocouples for exhaust temperature measurement of the PDE. The probe making process along with the calibration techniques for AWG 20, AWG 24 and AWG 50 thermocouples are discussed at length. The time constants for thermocouples were determined. Reactive mixture containing hydrogen and oxygen was used …

Distributed Inference And Learning With Byzantine Data, Bhavya Kailkhura

Dissertations - ALL

We are living in an increasingly networked world with sensing networks of varying shapes and sizes: the network often comprises of several tiny devices (or nodes) communicating with each other via different topologies. To make the problem even more complicated, the nodes in the network can be unreliable due to a variety of reasons: noise, faults and attacks, thus, providing

corrupted data. Although the area of statistical inference has been an active area of research in the

past, distributed learning and inference in a networked setup with potentially unreliable components

has only gained attention recently. The emergence of big and …

Molecular Dynamics Study Of Solid-Liquid Heat Transfer And Passive Liquid Flow, Sumith Yesudasan Daisy

Dissertations - ALL

High heat flux removal is a challenging problem in boilers, electronics cooling, concentrated photovoltaic and other power conversion devices. Heat transfer by phase change is one of the most efficient mechanisms for removing heat from a solid surface. Futuristic electronic devices are expected to generate more than 1000 W/cm2 of heat. Despite the advancements in microscale and nanoscale manufacturing, the maximum passive heat flux removal has been ~300 W/cm2 in pool boiling. Such limitations can be overcome by developing nanoscale thin-film evaporation based devices, which however require a better understanding of surface interactions and liquid vapor phase change process. Evaporation …

Systematic Discovery Of Android Customization Hazards, Yousra Aafer

Dissertations - ALL

The open nature of Android ecosystem has naturally laid the foundation for a highly fragmented operating system. In fact, the official AOSP versions have been aggressively customized into thousands of system images by everyone in the customization chain, such as device manufacturers, vendors, carriers, etc. If not well thought-out, the customization process could result in serious security problems. This dissertation performs a systematic investigation of Android customization’ inconsistencies with regards to security aspects at various Android layers.

It brings to light new vulnerabilities, never investigated before, caused by the under-regulated and complex Android customization. It first describes a novel vulnerability …

Cognitive Radio Systems: Performance Analysis And Optimal Resource Allocation, Gozde Ozcan

Dissertations - ALL

Rapid growth in the use of wireless services coupled with inefficient utilization of scarce spectrum resources has led to the analysis and development of cognitive radio systems. Cognitive radio systems provide dynamic and more efficient utilization of the available spectrum by allowing unlicensed users (i.e., cognitive or secondary users) to access the frequency bands allocated to the licensed users (i.e., primary users) without causing harmful interference to the primary user transmissions. The central goal of this thesis is to

conduct a performance analysis and obtain throughput- and energy-efficient optimal resource allocation strategies for cognitive radio systems. Cognitive radio systems, which …

Contributions On Theory And Practice For Multi-Mission Wireless Systems, Yu Zhao

Dissertations - ALL

The field of wireless systems has long been an active research area with various applications. Recently much attention has been given to multi-mission wireless systems that combine capabilities including information sensing, data processing, energy harvesting as well as the traditional data communication. This dissertation describes our endeavor in addressing some of the research challenges in multi-mission wireless systems, including the development of fundamental limits of such multi-mission wireless systems and effective technologies for improved performance.

The first challenge addressed in this dissertation is how to handle interference, which is encountered in almost all wireless systems involving multiple nodes, an attribute …

Resource Allocation For Interference Management In Wireless Networks, Raghed El Bardan

Dissertations - ALL

Interference in wireless networks is a major problem that impacts system performance quite substantially. Combined with the fact that the spectrum is limited and scarce, the performance and reliability of wireless systems significantly deteriorates and, hence, communication sessions are put at the risk of failure. In an attempt to make transmissions resilient to interference and, accordingly, design robust wireless systems, a diverse set of interference mitigation techniques are investigated in this dissertation.

Depending on the rationale motivating the interfering node, interference can be divided into two categories, communication and jamming. For communication interference such as the interference created by legacy …

Method Of Characteristics Verification Of Inverse Frequency Model Of Turbulent Pipe Flow Transients, Mohammad Saifullah Mohammad Zafar Shaikh

Mechanical and Aerospace Engineering Theses - Archive

Pressure transients in pipes with turbulent flow have classically been simulated using numerical techniques such as the method of characteristics. An alternative method utilizing an inverse frequency algorithm has recently been introduced for smooth pipe and determined to be computationally fast compared to the method of characteristics and in some cases more accurate. In addition, comparisons with experimental water hammer data has verified that the inverse frequency method is accurate out to Reynolds numbers of 15,800. This thesis investigates a comparison or the inverse frequency and method of characteristics methods for Reynolds numbers out to 200,000 for smooth pipes.

A Novel Stress Analysis Method For Laminated Composite Stiffener With Asymmetric Z-Section Under Mechanical And Thermal Loading Conditions, Sidhant Singh

Mechanical and Aerospace Engineering Theses - Archive

Composites structures are being used as load carrying members in latest aircrafts and performance automobiles, the design validation for such structures can be a time consuming and expensive process, if done by testing. Validation of a structure by analysis saves time and money for a design process and validation by analysis can be done by comparing the analytical solution with the finite element analysis of the structure, which requires availability of analytical expressions for every cross-sectional arrangement of the structural members. This research focuses on stress analysis of laminated composite stiffener with asymmetric Z-sections, where closed form analytical expressions are …