Engineering Commons^™

Performance Of Advance Warning Systems In A Coordinated System, Li Zhao, Laurence R. Rilett, Ernest Tufuor, Waleed Khan, Christopher Lefrois

Nebraska Department of Transportation: Research Reports

The Advance Warning System (AWS), developed by the Nebraska Department of Roads (NDOR) has proven to be effective at improving traffic safety at isolated signalized intersections. However, the effectiveness of the system has not been analyzed at signalized intersections operating in a coordinated mode. This project analyzed AWS on arterials where the signals operate in a coordinated mode. The test bed consisted of nine sites, which are located at five successive coordinated signalized intersections on Highway 281 in Grand Island, Nebraska. A non-intrusive data collection system was used to collect a continuous traffic stream of data up to 1200 ft …

Research On High-Rap Asphalt Mixtures With Rejuvenators And Wma Additives, Hamzeh Haghshenas, Hesanaddin Nabizadeh, Yong-Rak Kim, Kommidi Santosh

Nebraska Department of Transportation: Research Reports

No abstract provided.

Inquiry Of Graphene Electronic Fabrication, John Rausch Greene

Master's Theses

Graphene electronics represent a developing field where many material properties and devices characteristics are still unknown. Researching several possible fabrication processes creates a fabrication process using resources found at Cal Poly a local industry sponsor. The project attempts to produce a graphene network in the shape of a fractal Sierpinski carpet. The fractal geometry proves that PDMS microfluidic channels produce the fine feature dimensions desired during graphene oxide deposit. Thermal reduction then reduces the graphene oxide into a purified state of graphene. Issues arise during thermal reduction because of excessive oxygen content in the furnace. The excess oxygen results in …

Preparation And Microstructure Of Machinable Al2O3/Mica Composite By Ball Milling And Hot-Press Sintering, Qingbo Tian, Deyu Kong, Tongguang Zhai

Chemical and Materials Engineering Faculty Publications

A machinable α-Al₂O₃/mica composite was prepared by hot-press sintering. In this experiment, a mica-contained glass ceramic in the MgO-Al₂O₃-SiO₂-F glassy system was employed and the base glass powders were obtained by traditional melting-quenched method. Then, α-Al₂O₃ milling swarf was introduced by medium α-alumina milling ball to the glass powders. The test results indicate that the composites consist of mica crystal and mullite crystal, which are precipitated in the base glass. The α-Al₂O₃ shows an irregular polygon, which is inlayed in the base material. With …

Frequency Based Noise Coherence-Function Extension And Application To Passive Bottom-Loss Estimation, Lanfranco Muzi, Martin Siderius, Peter L. Nielsen

Electrical and Computer Engineering Faculty Publications and Presentations

Accurate modeling of acoustic propagation in the ocean waveguide is important to SONAR-performance prediction. Particularly in shallow waters, a crucial contribution to the total transmission loss is the bottom refection loss, which can be estimated passively by beamforming the natural surface-noise acoustic field recorded by a vertical line array of hydrophones. However, the performance in this task of arrays below 2 m of length is problematic for frequencies below 10 kHz" role="presentation" style="display: inline; line-height: normal; word-spacing: normal; word-wrap: normal; white-space: nowrap; float: none; direction: ltr; max-width: none; max-height: none; min-width: 0px; min-height: 0px; border: 0px; padding: 0px 2px 0px …

Materials And Techniques Used In Cranioplasty Fixation: A Review, Basel A. Khader, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

Cranioplasty is the surgical repair of a deficiency or deformity of the skull. The purpose of cranioplasty is to provide protection for the brain following cranial surgery, and to offer relief to psychological disadvantages while increasing social performance. There are several materials that had been used for cranioplasty, but an ideal product has yet to be developed, hence the ongoing research into biologic and non-biologic alternatives to the existing materials. This article critiques the products currently used for cranioplasty in order to facilitate the development of new materials, which can improve patient outcomes.

Conversion Of Glycerol To 1,3-Propanediol Under Haloalkaline Conditions, Melanie R. Mormile, Daniel William Roush, Dwayne A. Elias, Oliver C. Sitton

Biological Sciences Faculty Research & Creative Works

A method of producing 1,3-propanediol. The method comprises fermenting a haloalkaliphilic species of Halanaerobium with a source of glycerol into 1,3-propanediol, at a pH of greater than about 10 and at a salt concentration of greater than about 5% w/v. Furthermore, with supplementation of vitamin B₁₂, the yield of 1,3-propanediol to glycerol can be increased.

Recovery Of Agricultural Nutrients From Biorefineries, Daniel Elliott Carey, Yu Yang, Patrick J. Mcnamara, Brooke K. Mayer

Civil and Environmental Engineering Faculty Research and Publications

This review lays the foundation for why nutrient recovery must be a key consideration in design and operation of biorefineries and comprehensively reviews technologies that can be used to recover an array of nitrogen, phosphorus, and/or potassium-rich products of relevance to agricultural applications. Recovery of these products using combinations of physical, chemical, and biological operations will promote sustainability at biorefineries by converting low-value biomass (particularly waste material) into a portfolio of higher-value products. These products can include a natural partnering of traditional biorefinery outputs such as biofuels and chemicals together with nutrient-rich fertilizers. Nutrient recovery not only adds an additional …

Fall 2016

In The Loop

Dean David Miller and CDM Through the Years; The New ABCs of Digital Literacy; The Younger Generation: Computer Scientists of the Future; The Final Hurdle: Thesis Talk; Telling Stories in Cuba with Abbas Kiarostami with James Choi; Collegiate Cyber Defense Competition; TEDxDePaulUniversity Conference; Tim Nedow, Olympian; Omnibus Crowdfunded Game; News Briefs; The Social Technocrat: Andrew Ruginis; When Computing and Biology Collide; Tori Meschino: Campus Leader and All-Around Superstar; Degrees Offered at CDM

A Measurement System For Science And Engineering Research Center Performance Evaluation, Elizabeth Carole Gibson, Tugrul U. Daim

Engineering and Technology Management Faculty Publications and Presentations

This research is focused on gaining deeper insights into US National Science Foundation (NSF) science and engineering research center challenges and motivated to develop a method that effectively measures the performance of these organizations. While research has addressed organizational performance at the micro, or single-actor level for universities or companies and at the regional or national macro level, the middle level where the NSF centers reside is largely missing. The bulk of the cooperative research center studies use either case-based methods or bibliometric data to measure traditional research outputs. Many are excellent studies; however, they only focus on a piece …

Technology Evaluation Of Robotics Technology In Power Industry, Byung Sung Yoon, Judith Estep, Terry Oliver, Robert Grizzi

Engineering and Technology Management Faculty Publications and Presentations

The electric power utilities as important social infrastructures should be operated stably without any failure in supply of electricity. For stable operation, it is necessary to input huge amount of resource and investment throughout power generation, transmission and distribution facilities. Particularly, constant inspection and maintenance of the facilities requires highly skilled manpower and advanced technologies. In spite of endless efforts, the electric power industry is facing serious challenges from social, economic and environmental problems. In this regard, a number of robotic systems have been tested and applied for inspection and maintenance in nuclear power plants and high voltage power transmission …

Understanding Risk Perception Using Fuzzy Cognitive Maps, Pei Zhang, Antoine J. Jetter

Engineering and Technology Management Faculty Publications and Presentations

When making decision that can have far-researching effects, such as governmental policies or decisions on new technologies, decision-makers use their understanding of the risks that are associated with their choices to guide their decisions. Measuring how people perceive risks can be helpful for understanding and possibly improving the decision-making process. Building on a review of existing methods for investigating risk perceptions, this paper suggests Fuzzy Cognitive Maps (FCM) as a method for investigating differences in risk perception among stakeholders and stakeholder groups. The approach is illustrated with an example of wildfire risk perceptions. Results suggest that FCM can contribute to …

Decision-Making Model On Dslr Camera Choosing For 18 ∼ 30 Years Old College Students, Pei Zhang, Chih-Jen Yu, Jiabing Zhang, Monticha Khammuang, Dundar F. Kocaoglu

Engineering and Technology Management Faculty Publications and Presentations

A 3-level Hierarchical Decision Model (HDM) 111 is established in this paper to help 18-30 year old college students make a decision of choosing a desirable digital single-lens reflex camera (DSLR) from 5 famous DSLR camera manufacturers. The HDM has been utilized in this paper, because it measures the relative contribution of each criterion to the final decision based on quantified judgments of the respondents. A group of experts, consists of 12 male and 9 female provided their quantified judgements with different weighted value in each element at each level of the decision hierarchy. By applying desirable functions, there was …

Effects Of Breast Density And Compression On Normal Breast Tissue Hemodynamics Through Breast Tomosynthesis Guided Near-Infrared Spectral Tomography, Kelly E. Michaelsen, Venkataramanan Krishnaswamy, Linxi Shi, Srinivasan Vedantham, Andrew Karellas, Brian W. Pogue, Keith D. Paulsen, Steven P. Poplack

Dartmouth Scholarship

Optically derived tissue properties across a range of breast densities and the effects of breast compression on estimates of hemoglobin, oxygen metabolism, and water and lipid concentrations were obtained from a coregistered imaging system that integrates near-infrared spectral tomography (NIRST) with digital breast tomosynthesis (DBT). Image data were analyzed from 27 women who underwent four IRB approved NIRST/DBT exams that included fully and mildly compressed breast acquisitions in two projections—craniocaudal (CC) and mediolateral-oblique (MLO)—and generated four data sets per patient (full and moderate compression in CC and MLO views). Breast density was correlated with HbT (r=0.64, p=0.001), water (r=0.62, p=0.003), …

Microdose Fluorescence Imaging Of Aby-029 On An Operating Microscope Adapted By Custom Illumination And Imaging Modules, Jonathan T. Elliott, Alisha V. Dsouza, Kayla Marra, Brian W. Pogue, David Roberts, Keith Paulsen

Dartmouth Scholarship

Fluorescence guided surgery has the potential to positively impact surgical oncology; current operating microscopes and stand-alone imaging systems are too insensitive or too cumbersome to maximally take advantage of new tumor-specific agents developed through the microdose pathway. To this end, a custom-built illumination and imaging module enabling picomolar-sensitive near-infrared fluorescence imaging on a commercial operating microscope is described. The limits of detection and system specifications are characterized, and in vivo efficacy of the system in detecting ABY-029 is evaluated in a rat orthotopic glioma model following microdose injections, showing the suitability of the device for microdose phase 0 clinical trials.

Brain Encoding Of Saltatory Velocity-Scaled Somatosensory Array In Glabrous Hand Among Neurotypical Adults, Hyuntaek Oh

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Neurons in human somatosensory cortex are somatotopically organized, with sensation from the lower limbs mediated by neurons near the midline of the brain, whereas sensations from the upper body, hands and orofacial surfaces are mediated by neurons located more laterally in a sequential map. Neurons in Brodmann's area (BA) 3b are exquisitely sensitive to tactile stimulation of these skin surfaces. Moreover, the location, velocity and direction of tactile stimuli on the skin's surface are discriminable features of somatosensory processing, however their role in fine motor control and passive detection are poorly understood in health, and as a neurotherapeutic agent in …

Reflectance Measures From Infant Ears With Normal Hearing And Transient Conductive Hearing Loss, Susan E. Voss, Barbara S. Herrmann, Nicholas J. Horton, Elizabeth A. Amadei, Kujawa G. Sharon

Engineering: Faculty Publications

Objective: The objective is to develop methods to utilize newborn reflectance measures for the identification of middle-ear transient conditions (e.g., middle-ear fluid) during the newborn period and ultimately during the first few months of life. Transient middle-ear conditions are a suspected source of failure to pass a newborn hearing screening. The ability to identify a conductive loss during the screening procedure could enable the referred ear to be either (1) cleared of a middle-ear condition and recommended for more extensive hearing assessment as soon as possible, or (2) suspected of a transient middle-ear condition, and if desired, be rescreened before …

Portable Modular Conveyor, Purdue Ect Team

ECT Fact Sheets Archive

The Portable Modular Conveyor-Material Placer (PMC) is a quick, easy, dependable and cost effective way to place materials in the limits of the confined grade or work area. This specialized piece of equipment was developed to place concrete in front of a concrete slip form-paving machine. The typical method of placing concrete requires a self-propelled belt placer, which is very expensive to purchase and mobilize to the jobsite. The PMC creates a significant cost savings in labor and equipment with the PMC. It is a direct replacement for conventional material placing equipment, including all in grade belt placing machines. As …

The Use Of A Fractional Factorial Design To Determine The Factors That Impact 1,3-Propanediol Production From Glycerol By Halanaerobium Hydrogeniformans, Shivani Kalia, Jordan Trager, Oliver C. Sitton, Melanie R. Mormile

Biological Sciences Faculty Research & Creative Works

In recent years, biodiesel, a substitute for fossil fuels, has led to the excessive production of crude glycerol. The resulting crude glycerol can possess a high concentration of salts and an alkaline pH. Moreover, current crude glycerol purification methods are expensive, rendering this former commodity a waste product. However, Halanaerobium hydrogeniformans, a haloalkaliphilic bacterium, possesses the metabolic capability to convert glycerol into 1,3-propanediol, a valuable commodity compound, without the need for salt dilution or adjusting pH when grown on this waste. Experiments were performed with different combinations of 24 medium components to determine their impact on the production of …

Rapidscat Slice Spatial Response Function Contour Parameterization, John Clyde Niedfeldt

Theses and Dissertations

The spatial response function (SRF) of the backscatter measurements for a radar scatterometer is often used in reconstruction. It has been found that in many cases the SRF can be approximated as a binary function that is 1 inside the - 6 dB contour of the SRF and 0 outside. This improves the computation speed of reconstruction. Computing the SRF contour can still be a lengthy computation, which can be simplified by precomputing and tabulating key SRF contours. The tabular parameterization for many spinning scatterometers, i.e., QuikSCAT, is straight-forward. For RapidSCAT, this estimation is more involved than other radars due …

Assessment Of The Correlation Between Memory Span Test Result And Attention Using A Wireless Eeg System, Yu Yu

Theses and Dissertations

The process to encode, retain and retrieve information is known as memory. Ever since models for short-term memory and working memory systems were proposed, the function and importance of the short-term memory and working memory systems have been explored by a number of studies which in part have examined factors which may affect memory capacity. Although there are many undetermined factors which may affect the result of these two different memory span test, recent studies have suggested a link between human mental condition and memory capacity. These studies show that the results of simple memory span tests are improved when …

Bs News September/October

Building Services Engineering

No abstract provided.

Wetlands And Coastal Systems: Protecting And Restoring Valuable Ecosystems, C. T. Agouridis, K. R. Douglas-Mankin, A. C. Linhoss, A. R. Mittelstet

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Wetlands and coastal systems are unique, highly productive, and often threatened landscapes that provide a host of services to both humans and the environment. This article introduces a five-article Wetlands and Coastal Systems Special Collection that evolved from a featured session at the 2015 ASABE Annual International Meeting in New Orleans, Louisiana. The Collection provides perspectives on tools and techniques for enhancing the protection and restoration of wetlands and coastal systems with emphasis on vegetation, hydrology, water quality, and planning. Topics span the Florida Everglades (two articles) and Virginia floodplain (one article) wetland systems and include remote sensing (one article) …

A Comparison Of Wavelet And Simplicity-Based Heart Sound And Murmur Segmentation Methods, Joshua David Korven

Master's Theses

Stethoscopes are the most commonly used medical devices for diagnosing heart conditions because they are inexpensive, noninvasive, and light enough to be carried around by a clinician. Auscultation with a stethoscope requires considerable skill and experience, but the introduction of digital stethoscopes allows for the automation of this task. Auscultation waveform segmentation, which is the process of determining the boundaries of heart sound and murmur segments, is the primary challenge in automating the diagnosis of various heart conditions. The purpose of this thesis is to improve the accuracy and efficiency of established techniques for detecting, segmenting, and classifying heart sounds …

Post-Liquefaction Residual Strength Assessment Of The Las Palmas, Chile Tailings Failure, Tristan Reyes Gebhart

Master's Theses

Assessment of post-liquefaction residual strength is needed for the development of empirically-based, predictive correlations for earthquake engineering design. Previous practice commonly assigned negligible strengths to liquefied materials for engineering analysis, producing overly-conservative designs. Increasingly available case history data, and improved analytical tools have allowed for more accurate and less overly-conservative estimation of soil residual strength, improving empirical predictive models. This study provides a new case history to the limited suite of (approximately 30) liquefaction failure case histories available for post-liquefaction in-situ strength predictive correlations.

This case history documents the Las Palmas gold mine tailings dam failure, resulting from seismic-induced liquefaction …

Experimentation Of Mode I And Mode Ii Fracture Of Uni-Directional Composites And Finite Element Analysis Of Mode I Fracture Using Cohesive Contact, Joseph Daniel Garrett

Master's Theses

As the use of fiber-reinforced composites has increased over the decades, so has the need to understand the complexity of their failure mechanisms as engineers seek to improve the damage tolerance of composite laminated structures. One of the most prevalent and limiting mode of failure within composite laminates is delamination, since it not only reduces a structures stiffness and strength, but can be very difficult to detect without the use of special non-destructive equipment. Industry testing organizations have utilized several fracture tests in order to characterize the fracture toughness of composite materials under different loading conditions. For this research, ASTM …

A 3-D Multiplex Paper-Microfluidic Platform, Mitchell Patrick Young

Master's Theses

3-D paper-based microfluidic devices (micoPADs) are small and portable devices made out of paper that offer a promising platform for diagnostic applications outside of a laboratory. These devices are easy to use, low cost, require no power source, and capable of detecting multiple targets simultaneously. The work in this thesis demonstrated the ability of a 3-D paper-microfluidic platform to simultaneously detect 5 targets. Rubber cord stock was used in conjunction with an acrylic housing unit to apply pressure along the edge of the channel. The indirect pressure application was successful in promoting vertical fluid flow between layers. Average channel development …

Stress Related Fracturing In Dimension Stone Quarries, Ahmet Hamdi Deliormanli, Norbert H. Maerz

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

In Missouri, the horizontal stresses (pressures) in the near surface rock are uncommonly high. While the vertical stresses in rock are simply a function of the weight of the overlying rock, near surface stresses can be many times higher. The near surface horizontal stresses can be in excess of 5 times greater than the vertical stresses. In this research, Flatjack method was used to measure horizontal stress in Red Granite Quarry in Missouri. The flat jack method is an approved method of measuring ground stresses. A saw cut is used to "relax" the stress in the ground by allowing the …

Propulsion Theory Of Flapping Airfoils, Comparison With Computational Fluid Dynamics, Doug F. Hunsaker, W. F. Phillips

Mechanical and Aerospace Engineering Faculty Publications

It is shown that the time-dependent aerodynamic forces acting on a flapping airfoil in forward flight are functions of both axial and normal reduced frequencies. The axial reduced frequency is based on the chord length, and the normal reduced frequency is based on the plunging amplitude. Furthermore, the time-dependent aerodynamic forces are related to two Fourier coefficients, which are evaluated here from computational results. Correlation equations for these Fourier coefficients are obtained from a large number of grid- and time-step-resolved inviscid computational-fluid-dynamics solutions, conducted over a range of both axial and normal reduced frequencies. The correlation results can be used …

The Feasibility Of Utilising Compressed Natural Gas As Part Of A Systematic Approach To Establishing The Necessary Groundwork For The Hydrogen Based Transport Economy, James Brunton, John Howlett, David Kennedy

Conference Papers

One key objective for vehicle manufacturers is to develop technology and infrastructure to facilitate the progression from combustion to conversion by the year 2050. In the short to medium term however, the combustion of fossil fuels such as petrol and diesel, coupled with advanced transmission innovations and emission control technology that are governed by strict Euro VI regulations appears to be the main path forward for the transport sector and the environment. This paper presents the feasibility of utilising the developing compressed natural gas network capabilities as part of a systematic approach to establishing the necessary groundwork for a hydrogen …