Engineering Commons^™

Improvements To Micro-Contact Performance And Reliability, Tod V. Laurvick

Theses and Dissertations

Microelectromechanical Systems (MEMS) based devices, and specifically microswitches, continue to offer many advantages over competing technologies. To realize the benefits of micro-switches, improvements must be made to address performance and reliability shortfalls which have long been an issue with this application. To improve the performance of these devices, the micro-contacts used in this technology must be understood to allow for design improvements, and offer a means for testing to validate this technology and determine when such improvements are ready for operational environments. To build devices which are more robust and capable of continued operation after billions of cycles requires that …

Simulation Of Aircraft Sortie Generation Under An Autonomic Logistics System, Gunduz Bingol

Theses and Dissertations

Parallel to the developments in diagnostic and prognostic technology, autonomic logistics systems (ALS) have been a potential improvement for the aircraft sortie generation process. Currently, Lockheed Martin and the Joint Program Office are developing a new autonomic logistics system for the multibillion F-35 Lightning Joint Strike Fighter project, which is named the Autonomic Logistics Information System (ALIS). Generally, researchers make an analogy between the ALS and the human bodys autonomic nervous system since both of them monitor, control, and adjust autonomic responses to external stimuli. Based on this perspective, ALS aims to switch the Air Force logistics mentality from a …

Flow Field Dynamics In A High-G Ultra-Compact Combustor, Andrew E. Cottle

Theses and Dissertations

The Ultra Compact Combustor (UCC) presents a novel solution to the advancement of aircraft gas turbine engine performance. A high-g UCC design operates by diverting a portion of the axial compressor flow into a circumferential combustion cavity positioned about the engine outer diameter. The circumferential cavity (CC) provides the necessary residence length and time for combustion within reduced axial lengths; furthermore, high rates of centrifugal acceleration termed high-g loading are imposed upon the swirling cavity flow. These high-g conditions are hypothesized to increase flame speed, reduce flame length, and improve lean blow-out performance. Work at AFIT was sponsored by the …

Hot Ductility And Hot-Shortness Of Steel And Measurement Techniques: A Review, G Sahoo, M Deepa, B Singh, A Saxena

Journal of Metals, Materials and Minerals

Usage of steel scrap has become important in steel making from the view points of resource conservation and preventing environmental problems. High levels of steel scraps are used in the production of steel, especially, via electric arc furnaces (EAF). However, Copper, which is mainly contained in the scrap of cars and home electronic appliance, is problematic in mechanical workings at elevated temperatures and limits the usage of scrap iron. It is enriched at steel/scale interface by preferential oxidation of Fe, which leads to liquid embrittlement or surface cracking during hot working. This type of defect is well known as surface …

Petrographic Analysis Of Ceramic Artifacts From Ban Di Kiln, Pattani Province, Thailand, W Dhanmanonda, S Hongrittipun, D Aussavamas

Journal of Metals, Materials and Minerals

This research paper aims to investigate the components of archaeological ceramic artifacts collected from Ban Di kiln, Pattani province, Thailand. The procedure involves the petrographic examination of fragments of ceramic artifacts, focusing on raw materials, sources of materials, and production techniques. Ban Di ceramics date back to 16th and 17th centuries, the period in which ancient Patani had enjoyed its prosperity in domestic and foreign trade. This study shows that alluvial soils from coastal plains, with high content of sand, are predominant materials in the manufacture. The production process involves jiggering and hot pressing at the firing temperatures between 400-550 …

Dependence Of Electrical Resistivity On Plastic Deformation In Copper-Aluminum Alloy Cu0.975al0.025, J G Miranda Ramos, E Medrano Atencio, M Quiroga Agurto, F A Reyes Navarro

Journal of Metals, Materials and Minerals

We measure changes of electrical resistivity after a plastic deformation. We supposed that the changes are due to a large density of dislocation present in the polycrystalline samples; therefore, we also measure the amount of dislocations after the plastic deformation. Thus, for our aim, we elaborated copper-aluminum alloys Cu0.975Al0.025; next, with them, we fabricated metallographic specimens, which were submitted to traction subsequently. We measured the electrical resistivity before and after the traction. The obtained results are discussed in a theoretical framework of dislocations.

Information Technology News, Georgia Southern University

Information Technology: News & Publications (2012-2023)

• Data Science Capstone Project Featured in Georgia Southern Magazine Online

A Comparison Of Gestures For Virtual Object Rotation, Brandon Michael Garner

Theses and Dissertations

The fields of virtual reality and gesture-based input devices are growing and becoming more popular. In order for the two technologies to be implemented together, an understanding of gestures in relation to virtual objects and users' expectations of those gestures needs to be understood. Specifically, this thesis focuses on arm gestures for the rotation of virtual objects. Participants in the study were first asked to freely perform an arm gesture they felt should execute a task. Next, participants were asked to perform specific rotation tasks with pre- configured arm gestures on four objects. There were two types of objects: those …

Effects Of Tethering Placement And Linker Variations On Antibody Stability On Surfaces, Rebecca Ellen Grawe

Theses and Dissertations

An antibody microarray consists of antibody bound to a surface. Antibody microarrays have great potential in many fields, particularly as a tool to detect antigens. Unfortunately, antibodies suffer from poor performance. A greater understanding of how antibodies interact with surfaces would improve microarray design and performance, but experimental methods fall short of being able to observe these interactions. Therefore molecular simulation has emerged as the primary method to study protein/surface interactions.The simulations here were coarse grain simulations performed using the model of Karanicolas and Brooks. Additionally, an advanced surface model was used that allows for different surface chemistries. PyMBAR analysis …

Sulfate Resistance Of Nanosilica Contained Portland Cement Mortars, Iani Batilov Batilov

UNLV Theses, Dissertations, Professional Papers, and Capstones

Soils, sea water and ground water high in sulfates are commonly encountered hostile environments that can attack the structure of concrete via chemical and physical mechanisms which can lead to costly repairs or replacement. Sulfate attack is a slow acting deteriorative phenomenon that can result in cracking, spalling, expansion, increased permeability, paste-to-aggregate bond loss, paste softening, strength loss, and ultimately, progressive failure of concrete. In the presented research study, Portland cement (PC) mortars containing 1.5% to 6.0% nanosilica (nS) cement replacement by weight were tested for sulfate resistance through full submersion in sodium sulfate to simulate external sulfate attack. Mortars …

An Emg-Based Patient Monitoring System Using Zynq Soc Device, Farhad Fallahlalehzari

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis describes the design, development, and testing of an EMG-based patient monitoring system using the Zynq device. Zynq is a system on chip device designed by Xilinx which consists of an ARM dual cortex-A9 processor as well as an FPGA integrated into one chip. This work also analyzes the performance of image-processing algorithms on this system and compares that performance to more traditional PC-based systems. Image processing algorithms, such as Sobel edge detection, dilation and erosion, could be used in conjunction with a camera for the patient monitoring purposes. These algorithms often perform sub-optimally on processors because of their …

Acoustic Detection, Source Separation, And Classification Algorithms For Unmanned Aerial Vehicles In Wildlife Monitoring And Poaching, Carlo Lopez-Tello

UNLV Theses, Dissertations, Professional Papers, and Capstones

This work focuses on the problem of acoustic detection, source separation, and classification under noisy conditions. The goal of this work is to develop a system that is able to detect poachers and animals in the wild by using microphones mounted on unmanned aerial vehicles (UAVs). The classes of signals used to detect wildlife and poachers include: mammals, birds, vehicles and firearms. The noise signals under consideration include: colored noises, UAV propeller and wind noises.

The system consists of three sub-systems: source separation (SS), signal detection, and signal classification. Non-negative Matrix Factorization (NMF) is used for source separation, and random …

Causes And Impacts Of Geotechnical Problems On Bridge And Road Construction Projects, Krishna Prasad Neupane

UNLV Theses, Dissertations, Professional Papers, and Capstones

Changes during the construction phase generate cost growth, schedule delays, and claims in any project. However, the impact of geotechnical problems on construction costs, schedules, and claims in bridge and road projects had not been investigated in depth. The major objectives of this study were to determine the geotechnical-related causes of cost and schedule growth and claims as well as their impacts on the bridge and pavement projects’ performance. This study also identifies mitigation measures to avoid cost and schedule growth and claims in these projects.

A survey was conducted with 53 engineers from state Department of Transportations (DOTs) and …

Occurrence And Proliferation Of Antibiotics And Antibiotic Resistance In Wastewater Treatment Plants, Majid Neyestani

UNLV Theses, Dissertations, Professional Papers, and Capstones

Solids retention time (SRT) is one of the most important factors in designing and operating activated sludge systems for biological wastewater treatment. Longer SRTs have been shown to alter the structure and function of microbial communities, thereby leading to improved treatment efficacy with respect to bulk and trace organics, nutrient removal, and membrane fouling. However, research has also shown that longer SRTs lead to increased prevalence of antibiotic resistant bacteria, perhaps due to increased exposure to antibiotics present in influent wastewater. The purpose of this study was to characterize changes in microbial community structure in a laboratory-scale activated sludge system …

Radiation Therapy And Dosing Material Transport Methodology, Robert O'Brien

UNLV Theses, Dissertations, Professional Papers, and Capstones

A technique is examined here that utilizes high energy beta decays from a short lived radioisotope to treat medical conditions such as shallow cancerous lesions. A major benefit of beta particle interaction in tissue is a fixed penetration depth for the charged particle, with dose limited to the ultimate range of the beta particle. This method improves on some current techniques of radioactive brachytherapy, where "seeds" are placed inside patients through temporary or permanent implantation in order to kill cancerous cells or inhibit growth of tissue. The use of low energy gamma-rays is the most common method of treatment currently …

Process Development For The Fabrication Of Semiconductor Devices And Circuits Using Spin-On Dopant, Richard R. Ryan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Traditional approaches to semiconductor device fabrication are expensive and time consuming, making them out of reach for most universities and colleges. The objective of this thesis is to develop a process by which semiconductor devices and circuits can be implemented completely in-house using spin-on dopants (SODs), and low-cost transparency masks, to significantly reduce the lead time, complexity, and cost associated with device fabrication. This will allow hands on fabrication experience for students at universities and colleges without the traditional expensive device fabrication facilities. In addition, it will also allow students and professors to design, fabricate and test semiconductor devices and …

Evaluation Of Electron Donors For Perchlorate And Nitrate Biodegradation In Contaminated Groundwater Applications, Mayra Alejandra Sarria Cortes

UNLV Theses, Dissertations, Professional Papers, and Capstones

In the United States, perchlorate contamination has been widely reported, including in Las Vegas, Nevada, where perchlorate has been detected at concentrations of 34.7 mg/kg in vadose zone soil and 0.18-3.7 g/L in groundwater. Once this groundwater reaches the Las Vegas Wash, there is potential for widespread contamination of drinking water sources throughout the Southwest, including in Nevada, Arizona, and California. This issue is becoming increasingly important because even at low perchlorate concentrations, sensitive populations such as infants and pregnant women can be potentially impacted due to perchlorate’s ability to hinder iodine uptake into the thyroid glands, which leads to …

Ionic Electroactive Polymer Devices: Physics-Based Modeling With Experimental Investigation And Verification, Tyler Paul Stalbaum

UNLV Theses, Dissertations, Professional Papers, and Capstones

The primary focus of this study is to examine, understand, and model ionic electroactive polymer based systems in attempt to further develop this field of study. Physics-based modeling is utilized, as opposed to empirical modeling, to achieve a deeper insight to the underlying physics. The ionic electroactive polymer system of primary interest in this study is ionic polymer-metal composite (IPMC) devices. Other similar devices, such as anion-exchange membrane (AEM) type actuators and flow battery systems are also investigated using the developed model. The underlying physics are in the studies of transport phenomenon for describing the ionic flow within the polymer …

Analyses Of Streamflow Change Patterns And Correlation Of These Changes With Sea-Surface Temperature Fluctuations, Kazi Ali Tamaddun

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis presents a comprehensive statistical analysis that determines the direction, rate, and interval of significant streamflow change patterns in the continental U.S. and correlates these changes with sea-surface temperature fluctuations. First, by using two non-parametric tests, namely, the Mann-Kendall trend test and the Pettitt’s test, the presence of long-term trends and abrupt shifts were determined at 10% significance level over continuously adjustable periods that stretched from 1903 to 2012. Modified versions of the tests were applied to account for the presence of persistence (autocorrelation) in data. Theil-Sen slope was determined to evaluate the rate of change across multiple temporal …

The Effects Of Cryopreservation On Human Dental Pulp-Derived Mesenchymal Stem Cells, Allison Elaine Tomlin

UNLV Theses, Dissertations, Professional Papers, and Capstones

Many studies have demonstrated clinical applications for the use of dental pulp stem cells (DPSC) for the treatment of various conditions. This has driven medical and scientific interest in the collection, isolation and banking of DPSC tissues for research into these potential therapies. Few studies to date have evaluated the viability of DPSC following long-term cryopreservation. The purpose of this study is to evaluate the effects of cryopreservation on dental pulp-derived stem cells (DPSC) viability over a period of three years. Dental pulp-derived stem cells were isolated and cultured from thirty-one healthy teeth. DPSC isolates were assessed for doubling-time and …

Pendulum Based Impact Testing Of Athletic Helmets Using The Nocsae Headform, Bradley Thorne

UNLV Theses, Dissertations, Professional Papers, and Capstones

Concussions in organized sports can have detrimental short-term and long-term effects on player’s health. The focus of this research is the development of a new state of the art test and certification standard for protective headgear. Baseball helmets and soccer soft headgear were used in these tests, but the ultimate goal is to create a universal set of test guidelines for all types of protective headgear. Modifications to current test standards outlined by the National Operating Committee on Standards for Athletic Equipment (NOCSAE) employed the use of a pendulum impactor, which facilitated additional measurements during head impact tests using a …

A Business Intelligence Framework For Network-Level Traffic Safety Analyses, Naveen Kumar Veeramisti

UNLV Theses, Dissertations, Professional Papers, and Capstones

Currently, there are both methodological and practical barriers that together preclude a substantial use of theoretically sound approaches, such as the ones recommended by the Highway Safety Manual (HSM), for traffic safety management. Although the state-of-the-art provides theoretically sound approaches such as the Empirical Bayes method, there are still various important capabilities missing. Methodological barriers include among others (i) lack of a theoretically sound approach for corridor-level network screening, (ii) lack of a comprehensive approach for estimation of Safety Performance Functions based on a simultaneous consideration of both crash patterns and associated explanatory variables, and (iii) lack of theoretically sound …

Dermal Uptake Directly From Air Under Transient Conditions: Advances In Modeling And Comparisons With Experimental Results For Human Subjects, G. C. Morrison, C. J. Weschler, G. Bekö

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

To better understand the dermal exposure pathway, we enhance an existing mechanistic model of transdermal uptake by including skin surface lipids (SSL) and consider the impact of clothing. Addition of SSL increases the overall resistance to uptake of SVOCs from air but also allows for rapid transfer of SVOCs to sinks like clothing or clean air. We test the model by simulating di-ethyl phthalate (DEP) and di-n-butyl phthalate (DnBP) exposures of six bare-skinned (Weschler et al. 2015, Environ. Health Perspect., 123, 928) and one clothed participant (Morrison et al. 2016, J. Expo. Sci. Environ. Epidemiol., 26, 113). The model predicts …

Towards Structuring Smart Grid: Energy Scheduling, Parking Lot Allocation, And Charging Management, Mehdi Rahmani-Andebili

All Dissertations

Nowadays, the conventional power systems are being restructured and changed into smart grids to improve their reliability and efficiency, which brings about better social, economic, and environmental benefits. To build a smart grid, energy scheduling, energy management, parking lot allocation, and charging management of plug-in electric vehicles (PEVs) are important subjects that must be considered. Accordingly, in this dissertation, three problems in structuring a smart grid are investigated.

The first problem investigates energy scheduling of smart homes (SHs) to minimize daily energy consumption cost. The challenges of the problem include modeling the technical and economic constraints of the sources and …

Integrated Design Of Downwind Land-Based Wind Turbines Using Analytic Gradients, Andrew Ning, Derek Petch

Faculty Publications

Wind turbines are complex systems where component-level changes can have significant system-level effects. Effective wind turbine optimization generally requires an integrated analysis approach with a large number of design variables. Optimizing across large variable sets is orders of magnitude more efficient with gradient-based methods as compared to gradient-free method, particularly when using exact gradients. We have developed a wind turbine analysis set of over 100 components where 90% of the models provide numerically exact gradients through symbolic differentiation, automatic differentiation, and adjoint methods. This framework is applied to a specific design study focused on downwind land-based wind turbines.

Downwind machines …

Task And Participant Scheduling Of Trading Platforms In Vehicular Participatory Sensing Networks, Heyuan Shi, Xiaoyu Song, Ming Gu, Jiaguang Sun

Electrical and Computer Engineering Faculty Publications and Presentations

The vehicular participatory sensing network (VPSN) is now becoming more and more prevalent, and additionally has shown its great potential in various applications. A general VPSN consists of many tasks from task, publishers, trading platforms and a crowd of participants. Some literature treats publishers and the trading platform as a whole, which is impractical since they are two independent economic entities with respective purposes. For a trading platform in markets, its purpose is to maximize the profit by selecting tasks and recruiting participants who satisfy the requirements of accepted tasks, rather than to improve the quality of each task. This …

Characterization And Delineation Of Karst Geohazards Along Rm652 Using Electrical Resistivity Tomography, Culberson County, Texas, Adam F. Majzoub

Electronic Theses and Dissertations

The Delaware Basin of West Texas and southeastern New Mexico is the major western subdivision of the Permian Basin and a northern extension of the Chihuahuan Desert. The major evaporite unit within the Delaware Basin is the Castile Formation, which consists of gypsum/anhydrite and is highly susceptible to dissolution and karsting. Manifestations of karst within the Castile outcrop are abundant and include sinkholes, subsidence features and caves, both epigene and hypogene in origin.

Land reconnaissance surveys conducted during the summer of 2015 documented abundant karst landforms in close proximity to a major thoroughfare, RM 652, in Culberson County, Texas. 2D …

Geotechnical Properties Of The Travis Peak (Hosston) Formation In East Texas: A Compressive And Tensile Strength Analysis Using Regression Analysis., Pawan Kakarla

Electronic Theses and Dissertations

The estimation of rock mass strength is a key parameter in geotechnical engineering which is used in the design of geotechnical structures like tunnels, dams and slopes. Geotechnical engineering is the branch of civil engineering which works on the principles of soil and rock mechanics to evaluate subsurface conditions, stability of slopes, foundations of structures and construction of earthworks. The main focus of this study was to calculate the strength of Lower Cretaceous Travis Peak Formation rocks of East Texas and to check the accuracy by comparing it with Regression analysis. The parameters which were used were the Uniaxial Compression …

Effects Of The Cooling Rate On The Shear Behavior Of Continuous Glass Fiber/Impact Polypropylene Composites (Gf-Ipp), H. Wafai, G. Lubineau, A. Yudhanto, M. Mulle, W. Schijve, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Fiber-reinforced composites with improved dissipation of energy during impact loading have recently been developed based on a polypropylene copolymer commonly called impact polypropylene (IPP). Composites made of IPP reinforced with glass fibers (GF) are particularly attractive to the automotive industry due to their low cost and good impact resistance. In such composites, the cooling rate varies depending on processing techniques and manufacturing choices. Here, we study the effects of the cooling rate of GF-IPP composites on shear behavior, which is critical in impact applications, using [±45]s monotonic and cyclic (load/unload) tensile specimens. The specimens were manufactured under a wide range …

Bim Innovation Capability Programme: An Irish Bim Study, Barry Mcauley, Alan Hore, Roger West

Articles

In 2011 the Royal Institute of Architects Ireland (RIAI) conducted a survey which found that BIM adoption within Ireland was quite low at 16%. Over the last five years these figures have risen significantly, with the 2016 Irish Digital Transition Survey reporting that 76% of respondents possess confidence in their organisation’s BIM skills and knowledge. This represents a significant shift of BIM adoption in Ireland over the last five years.

The BIM Innovation Capability Programme (BICP) Irish BIM study, builds on the findings from the BICP Global BIM Study by providing an in depth review of BIM in Ireland with …