Engineering Commons^™

Characterization Of A Hypersonic Quiet Wind Tunnel Nozzle, Cameron J. Sweeney

Open Access Theses

The Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University has been able to achieve low-disturbance flows at high Reynolds numbers for approximately ten years. The flow in the nozzle was last characterized in 2010. However, researchers have noted that the performance of the nozzle has changed in the intervening years. Understand ing the tunnel characteristics is critical for the hypersonic boundary-layer transition research performed at the facility and any change in performance could have signif icant effects on research performed at the facility. Pitot probe measurements were made using Kulite and PCB pressure transducers to quantify the performance changes since characterization …

Helical Strakes On High Mast Lighting Towers And Their Effect On Vortex Shedding Lock-In, Ayah Zahour

Open Access Theses

An experimental study on the effect of helical strakes on vortex induced vibrations and the lock-in phenomenon in High Mast Lighting Towers (HMLTs) is investigated. Two multi-sided tapered scaled models are clamped in place in a subsonic wind tunnel that is equipped with a hot-wire sensor and a traverse mechanism. The shedding frequency data is collected for the models with and without helically patterned strakes with the use of two different ropes. The responses of the tower models, for a Reynolds number of 44, 000, are compared and discussed under different configurations including: two directions of the model with respect …

Metrics Of Critical Pair Identification, Zixu Zhang

Open Access Theses

Critical Pair Identification works as a potential assistive tool for human air traffic controllers by identifying potentially dangerous situations that are not detected by proposed automated separation assurance systems. This concept specifically considers conflicts that might arise if aircraft unexpectedly deviate from their planned flight path in the near future. Five metrics of the critical pair concept, Critical Pair Count, Time to Risk Exposure, Lead Time, Risk Exposure Duration and Blunder Sensitivity Index, have been developed and mathematically defined to characterize the safety level of an aircraft pair or a volume of air space. Algorithm that computes proposed metrics is …

Analysis Of Composite Plates By Using Mechanics Of Structure Genome And Comparison With Ansys, Banghua Zhao

Open Access Theses

Motivated by a recently discovered concept, Structure Genome (SG) which is defined as the smallest mathematical building block of a structure, a new approach named Mechanics of Structure Genome (MSG) to model and analyze composite plates is introduced. MSG is implemented in a general-purpose code named SwiftComp™, which provides the constitutive models needed in structural analysis by homogenization and pointwise local fields by dehomogenization. To improve the user friendliness of SwiftComp™, a simple graphic user interface (GUI) based on ANSYS Mechanical APDL platform, called ANSYS-SwiftComp GUI is developed, which provides a convenient way to create some common SG models or …

Free Edge Stress Analysis Of Laminated Structures With Arbitrary Cross Sections Using Mechanics Of Structure Genome, Lingxuan Zhou

Open Access Theses

Composite laminates have been increasingly used in advanced structural applications, due to their excellent strength-to-weight properties and considerable flexibility on designing with respect to the laminate layup. However, the heterogeneity and anisotropy of composite laminates have brought many challenges for analysis and numerous researches have been devoted in this field. A well known problem which has been studied intensively is the so-called free-edge problem. It states that due to the mismatch in elastic properties of adjacent layers, full-scale three-dimensional (3D) and highly concentrated stress fields will occur in the vicinity of the free edges. The interlaminar stresses grow very rapidly …

Fea Methodology For System-Level Redundancy Evaluation: Application To Non-Composite Steel Bridges, Francisco Javier Bonachera Martin

Open Access Dissertations

Currently, all steel bridges with members designated as Fracture Critical Members (FCMs) are required to undergo hands-on inspections every 24 months. A FCM is a primary steel tension member (or portion of) which failure results in collapse or loss of serviceability of a bridge. However, presently, there are no codified procedures used to evaluate system-level redundancy in steel bridges. In this dissertation, finite element analysis (FEA) procedures, techniques and inputs were researched in order to develop bridge models that account for the mechanisms that lead to redundant capacity after the failure of a primary steel member. These mechanisms include partial …

Conceptual Understanding Of Threshold Concepts Of Electrical Phenomena: Mental Models Of Senior Undergraduates In Electrical Engineering, Mark T. Carnes

Open Access Dissertations

Every field of study has a set of domain-specific concepts that anyone who desires to work in that field must know and understand. Most students who pursue university degrees in engineering trust that their education is designed to provide them with this knowledge. But does it? In electrical engineering (EE), conceptual understanding of electrical phenomena has rarely been addressed. Even though the presumed goal of instructors and students alike is to learn the concepts of electrical phenomena well enough to be able to use the concepts to design useful things, it is difficult to determine whether this goal is being …

The Effects Of Chloride-Based Deicing Chemicals On Degradation Of Portland Cement Mortars With Alkali Reactive Aggregate, Charles Yicheng Chiu

Open Access Dissertations

The assessment of the influence of deicing chemicals on alkali reactivity of aggregates is still an area of active research, particularly with respect to the combined effects of long-term exposure to deicers, freezing and thawing cycles, and wetting and drying cycles. In order to develop a more comprehensive view of these topics, the present study was conducted in three phases. The focus of the first phase was on studying the effects of the chloride-based deicers on the alkali silica reaction (ASR) using accelerated test methods (i.e. the test was performed at high temperature (80 °C) as per modified ASTM C1260). …

The Association Between Tolerance For Ambiguity And Fear Of Negative Evaluation: A Study Of Engineering Technology Capstone Courses, Sergey I. Dubikovsky

Open Access Dissertations

For many students in engineering and engineering technology programs in the US, senior capstone design courses require students to form a team, define a problem, and find a feasible technical solution to address this problem. Students must integrate the knowledge and skills acquired during their studies at the college or university level. These truly integrative design activities do not have a single “correct” solution. Instead, there is an array of solutions, many of which could be used to achieve the final result. This ambiguity can cause students to experience anxiety during the projects.

This study examined the main topics: • …

Thermomechanical Properties Of Novel Lanthanum Zirconate Based Thermal Barrier Coatings - An Integrated Experimental And Modeling Study, Xingye Guo

Open Access Dissertations

Thermal barrier coatings (TBCs) are refractory materials deposited on gas turbine components, which provide thermal protection for metallic components at operating conditions. The current state-of-art TBC material is yttria-stabilized zirconia (YSZ), whose service temperature is limited to 1200 celsius, due to sintering and phase transition at higher temperatures. In comparison, lanthanum zirconate (La2Zr2O7, LZ) has become a promising candidate material for TBCs due to its lower thermal conductivity and higher phase stability compared to YSZ.

The primary objective of this thesis is to design a novel robust LZ-based TBC system suitable for applications beyond 1200 celsius. Due to LZ’s low …

Modeling Methods For Merging Computational And Experimental Aerodynamic Pressure Data, Jacob Courtney Haderlie

Open Access Dissertations

This research describes a process to model surface pressure data sets as a function of wing geometry from computational and wind tunnel sources and then merge them into a single predicted value. The described merging process will enable engineers to integrate these data sets with the goal of utilizing the advantages of each data source while overcoming the limitations of both; this provides a single, combined data set to support analysis and design. The main challenge with this process is accurately representing each data source everywhere on the wing. Additionally, this effort demonstrates methods to model wind tunnel pressure data …

Carbon Nanotube Thermal Interfaces And Related Applications, Stephen L. Hodson

Open Access Dissertations

The development of thermal interface materials (TIMs) is necessitated by the temperature drop across interfacing materials arising from macro and microscopic irregularities of their surfaces that constricts heat through small contact regions as well as mismatches in their thermal properties. Similar to other types of TIMs, CNT TIMs alleviate the thermal resistance across the interface by thermally bridging two materials together with cylindrical, high-aspect ratio, and nominally vertical conducting elements. Within the community of TIM engineers, the vision driving the development of CNT TIMs was born from measurements that revealed impressively high thermal conductivities of individual CNTs. This vision was …

Two-Dimensional Electronics And Optoelectronics: From Materials Syntheses To Device Applications, Yexin Deng

Open Access Dissertations

The current research on semiconductor device has pushed the scaling of the devices into sub-10 nanometers (nm) regime. While most of the current devices are made on silicon germanium, and III-V materials, people are looking for new materials for use in novel semiconductor devices: either for use in extremely scaled device in sub-10 or even sub-5 nm devices, or for use in other situations such as flexible electronics or low power and lower cost IoT (Internet of Things) applications.

Two-dimensional (2D) materials have attracted extensive research interests in their physical, chemical and mechanical properties.Since the discovery of graphene, which a …

Examination And Utilization Of Rare Features In Text Classification Of Injury Narratives, Hsin-Ying Huang

Open Access Dissertations

Thanks to the advances in computing and information technology, analyzing injury surveillance data with statistical machine learning methods has grown in popularity, complexity, and quality over recent years. During that same time, researchers have recognized the limitations of statistical text analysis with limited training data. In response to the two primary challenges for statistical text analysis, dimensionality reduction and sparse data, many studies have focused on improving machine learning algorithms. Less research has been done, though, to examine and improve statistical machine learning methods in text classification from a linguistic perspective.

This study addresses this research gap by examining the …

Concurrent Detection And Isolation Of Cellular And Molecular Biomarkers, Wanfeng Huang

Open Access Dissertations

Detection of cancer markers such as protein biomolecules and cancer cells in bodily fluids is of great importance in early diagnosis, prognosis as well as evaluation of therapy efficacy. Numerous devices have been developed for detecting either cellular or molecular targets, however there has not yet been a system that can simultaneously detect both cellular and molecular targets effectively. Molecule and cell-based assays are important because each type of target can tell a different story about the state of the disease and the two types of information can potentially be combined and/or compared for more accurate biological or clinical assessments. …

Exploring The Cause Of Injury Or Death In Grain Entrapment, Engulfment And Extrication, Salah F. Issa

Open Access Dissertations

Grain entrapments and engulfments are one of most common hazards associated with grain storage facilities. Since the 1970’s over 1,880 incidents have been documented in agricultural confined spaces of which 65% of all recorded incidents were grain entrapments and engulfments. There have been several studies conducted on the contributing factors behind these incidents; however, there have been very few attempts to understand the environmental, physiological or psychological factors the victims experience while entrapped, engulfed, or extricated. This includes understanding how secondary injuries are caused by grain or during extrication by first responders. The research effort was divided into three segments. …

A Method For Selecting Hvac Retrofit Solutions For Existing Small- And Medium-Sized Commercial Buildings, Bonggil Jeon

Open Access Dissertations

The primary purpose of the present study is to develop a framework and methodology for evaluating appropriate Heating, Ventilating, and Air Conditioning (HVAC) retrofit solutions that can be effectively retrofitted into different types of small- and medium-sized commercial buildings (SMSCB). Additionally, development of an advanced data-driven decision-making tool is introduced as a benefit of proposed framework. In recent years, considerable attention has been focused on retrofits of existing commercial buildings (IBE, 2013b). In fact, the Commercial Building Energy Consumption Survey (CBECS) 2003 (EIA, 2006) indicates that over 70% of existing commercial buildings across the United States are more than twenty …

Gravity-Assist Trajectories To Venus, Mars, And The Ice Giants: Mission Design With Human And Robotic Applications, Kyle M. Hughes

Open Access Dissertations

Gravity-assist trajectories to Uranus and Neptune are found (with the allowance of impulsive maneuvers using chemical propulsion) for launch dates ranging from 2024 to 2038 for Uranus and 2020 to 2070 for Neptune. Solutions are found using a patched conic model with analytical ephemeris via the Satellite Tour Design Program (STOUR), originally developed at the Jet Propulsion Laboratory (JPL). Delivered payload mass is computed for all solutions for select launch vehicles, and attractive solutions are identified as those that deliver a specified amount of payload mass into orbit at the target body in minimum time. The best cases for each …

Plasmonic Devices Based On Transparent Conducting Oxides For Near Infrared Applications, Kim Jongbum

Open Access Dissertations

In the past decade, there have been many breakthroughs in the field of plasmonics and nanophotonics that have enabled optical devices with unprecedented functionalities. Even though remarkable demonstration of at photonic devices has been reported, constituent materials are limited to the noble metals such as gold (Au) and silver (Ag) due to their abundance of free electrons which enable the support of plasmon resonances in the visible range. With the strong demand for extension of the optical range of plasmonic applications, it is now a necessity to explore and develop alternative materials which can overcome intrinsic issues of noble metals …

Optimal Design Of Sound Absorbing Systems With Microperforated Panels, Nicholas Nakjoo Kim

Open Access Dissertations

As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles.

This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound …

New Marked Point Process Models For Microscopy Images, Dae Woo Kim

Open Access Dissertations

In developing new materials, the characterization of microstructures is one of the key steps. To characterize the microstructure, many microscope modalities have been devised and improved over decades. With the increase in image resolution in the spatial and time domains, the amount of image data keeps increasing in the fields such as materials science and biomedical engineering. As a result, image processing plays a critical role in this era of science and technology. In materials image analysis, image segmentation and feature detection are considered very important.

The first part of this research aims to resolve the segmentation problem caused by …

Observability And Observer Design For Switched Linear Systems, Scott C. Johnson

Open Access Dissertations

Hybrid vehicles, HVAC systems in new/old buildings, power networks, and the like require safe, robust control that includes switching the mode of operation to meet environmental and performance objectives. Such switched systems consist of a set of continuous-time dynamical behaviors whose sequence of operational modes is driven by an underlying decision process. This thesis investigates feasibility conditions and a methodology for state and mode reconstruction given input-output measurements (not including mode sequence). An application herein considers insulation failures in permanent magnet synchronous machines (PMSMs) used in heavy hybrid vehicles.

Leveraging the feasibility literature for switched linear time-invariant systems, this thesis …

Evaluating The Performance Of Passive Chilled Beams With Respect To Energy Efficiency And Thermal Comfort, Janghyun Kim

Open Access Dissertations

Existing modeling approaches for passive chilled beams determined from tests on individual chilled beams in a laboratory are not adequate for assessing overall energy usage and occupant comfort within building simulation programs. In addition, design guidelines for passive chilled beam systems are needed for identifying appropriate applications and optimal configurations. This thesis includes (i) extensive experimental studies for characterizing the performance of passive chilled beams, in both laboratory settings and in field studies, (ii) development of passive chilled beam performance prediction models, (iii) integration of these models into building simulation models/tools and (iv) use of building simulation for overall assessment …

Device Design Factors For Enhancing The Functionality Of Chronic Intracortical Microelectrodes, Heui Chang Lee

Open Access Dissertations

Intracortical microelectrodes are devices used in brain-computer interfaces (BCI) to help regain lost motor, sensory, and cognitive functions of individuals with neurological disorders. However, the long-term performance of microelectrode arrays is hampered by a series of inflammatory tissue responses. The consequence of the inflammatory response is the formation of a dense astroglial sheath around the vicinity of the electrode, impeding the electrical conduction between the electrode and neurons. Furthermore, due to the cascade of neuroinflammatory events, the number of neurons is significantly reduced near the electrode, manifested by decrease in signal-to-noise ratio (SNR) and the yield of electrodes. Over time, …

Fast Time- And Frequency-Domain Finite-Element Methods For Electromagnetic Analysis, Woochan Lee

Open Access Dissertations

Fast electromagnetic analysis in time and frequency domain is of critical importance to the design of integrated circuits (IC) and other advanced engineering products and systems. Many IC structures constitute a very large scale problem in modeling and simulation, the size of which also continuously grows with the advancement of the processing technology. This results in numerical problems beyond the reach of existing most powerful computational resources. Different from many other engineering problems, the structure of most ICs is special in the sense that its geometry is of Manhattan type and its dielectrics are layered. Hence, it is important to …

Improving Programmability And Performance For Scientific Applications, Chenyang Liu

Open Access Dissertations

With modern advancements in hardware and software technology scaling towards new limits, our compute machines are reaching new potentials to tackle more challenging problems. While the size and complexity of both the problems and solutions increases, the programming methodologies must remain at a level that can be understood by programmers and scientists alike. In our work, this problem is encountered when developing an optimized framework to best exploit the semantic properties of a finite-element solver. In efforts to address this problem, we explore programming and runtime models which decouple algorithmic complexity, parallelism concerns, and hardware mapping. We build upon these …

What Broke Where For Distributed And Parallel Applications — A Whodunit Story, Subrata Mitra

Open Access Dissertations

Detection, diagnosis and mitigation of performance problems in today's large-scale distributed and parallel systems is a difficult task. These large distributed and parallel systems are composed of various complex software and hardware components. When the system experiences some performance or correctness problem, developers struggle to understand the root cause of the problem and fix in a timely manner. In my thesis, I address these three components of the performance problems in computer systems. First, we focus on diagnosing performance problems in large-scale parallel applications running on supercomputers. We developed techniques to localize the performance problem for root-cause analysis. Parallel applications, …

Modifying Burning Rate And Agglomeration Size In Aluminized Composite Solid Propellants Using Mechanically Activated Metals, Hatem Mohamed Belal

Open Access Dissertations

Agglomeration reduction techniques are important field in solid propellant industry, Large agglomeration results in excessive two phase losses. Tailored composite particles has been applied to tailor aluminum particle ignition and combustion. In this research, mechanical activated aluminum magnesium powders are synthesized, tested in both laser ignition using CO2 and propellant. Prepared powders categorized into particle size that suitable for propellant application. Laser ignition tests showed that the prepared powder are more reactive than magnalium which has the same Al:Mg weight ratio. Agglomeration capturing showed that the prepared powder produce much less than neat aluminum or even similar physical mixture of …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Hydrodynamics Of Swimming Microorganisms In Complex Fluids, Gaojin Li

Open Access Dissertations

Swimming motion of microorganisms, such as spermatozoa, plankton, algae and bacteria, etc., ubiquitously occurs in nature. It affects many biological processes, including reproduction, infection and the marine life ecosystem. The hydrodynamic effects are important in microorganism swimming, their nutrient uptake, fertilization, collective motions and formation of colonies. In nature, microorganisms have evolved to use various fascinating ways for locomotion and transport. Different designs are also developed for the locomotion of artificial nano- and microswimmers. In this study, we use several different computational models to investigate the behavior of microswimmers.

Microorganisms typically swim in the low Reynolds number regime, where inertia …