Engineering Commons^™

Safety Airway For Small Unmanned Aerial Vehicles Using A Gas Particles Behavior Analogy, Pablo Rangel

Open Access Theses & Dissertations

The United States Federal Aviation Administration (FAA) implemented the Part 107 legislation to allow the flight of Unmanned Aerial Vehicles (UAV) for commercial use (i.e. package deliveries, power transmission line inspections, etc.) in the National Airspace System (NAS). As a consequence of the newly introduced rules, there is an increased risk for accidents involving injured bystanders or damaged to property. The work within this document defines a UAV to UAV safety distance model that acts as a range sensor enabled "elastic bubble". The length of the UAV safety bubble contracts and expands upon changing airway wind speed conditions. It also …

Three Dimensional Finite Element Model For Residual Stresses In Parts Manufactured By Slm And Ebm, Jesus Gerardo Reyes Schuldes

Open Access Theses & Dissertations

Ongoing research efforts in industry and academia have a focus on optimal build parameters that lead to suitable mechanical properties with minimum defects in parts manufactured by powder bed fusion additive manufacturing technologies, such as Electron Beam Melting (EBM) and Selective Laser Melting (SLM). Additional and significant resources, including energy, time, and money are spent as a result of obligatory post-manufacturing heat and/or mechanical treatment to ensure optimum mechanical properties. One intrinsic fault in these technologies, which contributes to the need for treatment processes after part fabrication, is the creation of residual stresses during these processes. Residual stresses remain in …

The Former Asarco Demolition Fallout, A Post Study On Lead Soil Concentrations And Environmental Agents Of Redistribution In El Paso, Texas, Stephanie A. Robinson

Open Access Theses & Dissertations

The former El Paso ASARCO Smelting and Refining Co. operated between 1877 and 1999, the pyrometallurgic activity was estimated to have discharged excess of a 1,000 tons of lead (Pb) into the atmosphere from 1969-71. It was estimated 96 tons of (Pb) were emitted on an annual basis from the standing ore and fluid beds. The Environmental Protection Agency (EPA) determined that lead (Pb) is the heavy metal of the highest concentration within the vicinity of the smelter. After the smelter production ceased, flash flooding common to the southwest, such as the 2006 historic flood, increased transportation of superficial contaminants …

Modeling The Effects Of Manufacturing Geometric Imperfections In The Buckling Analysis Of Three-Dimensional Structures, Juan Carlos Salcido

Open Access Theses & Dissertations

Reticulated three-dimensional structures follow design practices based on the common assumption that joints are either rigid, or pinned. However, the actual non-linear behavior of the jointing system interaction is required to be incorporated into the analysis of the structure to accurately predict its buckling stability. Besides, currently, there is a concern on how manufacturing imperfections of these jointing systems affect the global behavior of three-dimensional structures. This Dissertation incorporates and captures the effect that manufacturing geometric imperfections in the fir-tree jointing system produce in the non-linear buckling behavior of three-dimensional structures.

To understand the effect that initial manufacturing imperfections of …

Experimental Investigation Of Cryogenic Convection And Boiling In Traditionally And Additively Manufactured Rocket Engine Cooling Channels, Armando Sandoval

Open Access Theses & Dissertations

The Center for Space Exploration and Technology Research at the University of Texas at El Paso, has designed, built, and optimized an experimental high heat flux test facility to investigate the heat transfer coefficient of liquid methane and other cryogenic propellants for regenerative cooled rocket engine design. The system is composed of a copper conduction based thermal concentrator that delivers heat flow into a single sub-scaled cooling channel (test article). This study focuses on optimizing this design of the high heat flux test facility to develop a more accurate method for measuring the conductive heat flow going into the cooling …

Pyroelectric Ceramics As Temperature Sensors For Energy System Applications, Jorge Luis Silva

Open Access Theses & Dissertations

Temperature is continuously monitored in energy systems to ensure safe operation temperatures, increase efficiency and avoid high emissions. Most of energy systems operate at high temperature and harsh environments to achieve higher efficiencies, therefore temperature sensing devices that can operate under these conditions are highly desired. The interest has increased in temperature sensors capable to operate and in harsh environments and temperature sensors capable to transmit thermal information wirelessly. One of the solutions for developing harsh environment sensors is to use ceramic materials, especially functional ceramics such as pyroelectrics. Pyroelectric ceramics could be used to develop active sensors for both …

Design & Analysis Of A 500 Lbf Liquid Oxygen And Liquid Methane Rocket Engine, Daniel Eduardo Vargas

Open Access Theses & Dissertations

The rapid growth in demand for spacecraft technologies has spawned a need for a variety of new and innovative research. The utilization of liquid oxygen (LOX) and liquid methane (LCH4) in rocket engines have played an important role in space exploration efforts to promote missions to Mars with in-situ resource utilization for propellant production. This will allow the production of fuel needed to come back to Earth making the overall mission more cost effective by enabling larger usable mass.

The Center for Space Exploration and Technology Research has focused its efforts to developing Liquid Oxygen (LOX) and Liquid Methane (LCH4) …

Comprehensive Finite Element Modeling Of Ti-6al-4v Cellular Solids Fabricated By Electron Beam Melting, Edel Arrieta

Open Access Theses & Dissertations

Additive manufacturing permits the fabrication of cellular metals which are materials that can be highly customizable and possess multiple and extraordinary properties such as damage tolerance, metamorphic and auxetic behaviors, and high specific stiffness. This makes them the subject of interest for innovative applications. With interest in these materials for energy absorption applications, this work presents the development of nonlinear finite element models in commercial software platforms (MSC Patran/Nastran) that permit the analysis of the deformation mechanisms of these materials under compressive loads. In the development of these models, a detailed multiscale study on the different factors affecting the response …

Dft Study Of Adsorption Of Trimetallic Endohedral Fullerenes On Graphene, Nakul Nitin Karle

Open Access Theses & Dissertations

A density functional theory (DFT) study on the geometric and electronic structure of C60 and Sc3N@C80 along with their adsorption on pristine single layer graphene (SLG) is presented. C60 is found to adsorb in two nearly degenerate configurations: (i) with a pentagon facing the SLG, which is the most stable one, and (ii) with a hexagon facing the SLG in a face-to-face perfect alignment, rarely common in Ï?â??Ï? interactions, 0.06 eV higher in energy. The calculated binding energy of 0.76 eV, which includes dispersion effects, is in good agreement with previous theoretical and experimental reports. On the contrary, Sc3N@C80 adsorption …

Design Of A Feed System For An Oxy-Methane High Pressure Combustor, Jorge Arturo Rosero

Open Access Theses & Dissertations

With growing concern over the effects that fossil fuels are having on the environment and the expected increases in energy demand in the coming decades, it is becoming increasingly more important to find cleaner and more efficient ways to generate energy. Natural gas has grown in popularity in the last decade thanks to a drastic drop in price and its lower carbon emissions compared to coal. With enough natural gas reserves in the United States to last over 90 years, natural gas is expected to be a large part of the future energy outlook.

Increased demand from growing populations also …

Overview Of Metrics, Models, And Simulation For Cyber-Physical Systems, Barry C. Ezell, Luanne Burns Chamberland

VMASC Publications

The metric, models, and simulation for Cyber-Physical Systems focuses on the different frameworks that have been operationalized so that cyber-physical systems can be baselined in security. In addition, the minitrack is interest in innovations in decision support such as cost effective means to decide what metrics should be addressed to get the best value in cybersecurity. There are many challenges to overcome in cyber-physical systems. We ask: How should frameworks be operationalized? What methodologies are available to quantify cybersecurity frameworks while accounting for cyber-physical interactions into account.

Bragg Gratings In Polarization Maintaining Optical Fiber As Three Dimensional Strain Sensor, Joel Quintana

Open Access Theses & Dissertations

Fiber-Bragg Gratings (FBG) for Structural Health Monitoring (SHM) have been studied extensively as they offer electrically passive operation, electromagnetic interference (EMI) immunity, high sensitivity and multiplexing as compared to conventional electric strain sensors. FBG sensors written within polarization maintaining (PM) optical fiber offer ad- ditional dimensions of strain measurement, greatly reducing the number of sensors needed to properly monitor a structure. This reduction however, adds complexity to the dis- crimination of the sensorâ??s optical response to its corresponding applied strains. This Dissertation defines the set of algorithms needed to measure planar strain using PM-FBGs exclusively. It defines the minimum number …

Optimization Of Collagen Microneedle Using Taguchi Method, Abhilash Aditya

Open Access Theses & Dissertations

Research is conducted to create dissolving collagen microneedles and to optimize the parameters for close to perfect dimension microneedles. A collagen microneedle patch has been developed with a micro-manufacturing process (micro-molding process). The collagen microneedles, varying in length from 300 to 600-μm may reach different targeted layers of the skin depending on the application. As the microneedles penetrate the skin they dissolve, delivering collagen through the epidermis. Such addition of collagen directly to the dermis layers allows it to be absorbed, increasing skin's strength and resilience, since it is one of the natural components of the younger looking skin. This …

An In-Depth Evaluation Of Shear Box Compactor For Hot Mix Asphalt, Isaac Jaime Aguilar

Open Access Theses & Dissertations

Asphalt pavement is present in each roadway in every town or city today and it is paramount to properly design pavement to efficiently reduce its deterioration. To determine how pavement fails, pavement specimens prepared in the laboratory undergo performance tests which demonstrate the pavements strength and durability. Performance tests require little variability from compacted specimens, and it is critical to have a compaction method which is similar to field compaction and produces homogenous specimens. Currently, laboratory performance test specimens are obtained with the Superpave Gyratory Compactor (SGC). That device has few similarities to the rolling compactor, which performs the actual …

Studies Of Air Pollutants And Their Impact On Respiratory And Cardiovascular Diseases In The El Paso Del Norte Region With Emphasis On Mobile Emissions, Juan Gustavo Arias Ugarte

Open Access Theses & Dissertations

Air pollution may cause different diseases, such as cardiovascular and lung diseases. Traffic is a major source of mobile emissions causing air pollution. Exhaust emissions from mobile sources (Emissions of Carbon Monoxide, Nitrogen Oxides and Hydrocarbons) and Non-exhaust (Brake and Tire) are complex mixtures of gases and dust, including a large number of ultrafine particles, especially in areas with high traffic density. Recent studies have shown high rates of morbidity and mortality in people exposed to these types of emissions because the fine and ultrafine particles can be transported from the respiratory airways to the organs, thus contributing to increase …

Characterization Of Electrically Conductive Inks In Simulated Space Environment, Kazi Md Masum Billah

Open Access Theses & Dissertations

Increasing numbers of satellite missions necessitate a standalone power supply with self-recovery capabilities in case of failure in the space environment. A self-repairing kit was developed with the capabilities to repair the damaged solar array by dispensing conductive inks. Dispensing of conductive materials using direct writing technology to the space environment not only repairs damaged electronic components but also demonstrates the possibilities of manufacturing in outer space. For earth application, properties of direct writing inks have been evolved. In space application, direct writing inks or conductive inks have some issues such as outgassing, vapor pressure, curing etc.Therefore, having the properties …

Organic-Inorganic Graphite And Transition Metal Dichalcogenide Based Composites For 3d Printing, Jorge Alfredo Catalan Gonzalez

Open Access Theses & Dissertations

This project was multipronged to help fuse together topics of additive manufacturing and two-dimensional (2D) layered materials, and studying the mechanical and electrical properties of the composites produced. The composites are made from the thermoplastic polymer acting as a matrix and the graphite and 2D transition metal dichalcogenides (TMDs) serving as the filler or reinforcement. Different concentrations of TMD's were added to the matrix to study the effect of composition on the mechanical and electrical properties. To shed insights into the mechanical properties, test coupons were produced as "dog bone" structures for tensile testing using the ASTM D638 type 5 …

The Development Of A Data Acquisition And Control System For Rocket Propulsion Research, Javier Chaparro

Open Access Theses & Dissertations

The MIRO Center for Space Exploration Technology Research (cSETR) at the University of Texas at El Paso (UTEP) has developed the Technology Research and Innovation Acceleration Park (tRIAC) in Fabens, Texas. This facility has been established in order to meet new research demands for experimental testing of Liquid Oxygen (LOX)/Liquid methane (LCH4) propulsion systems. Within this facility, a vertical test stand capable of measuring up to 3,000lbf will be constructed for main engine testing of the JANUS and DAEDALUS vehicle programs.

In order to meet challenges of precise remote system operation and data acquisition during engine testing, cSETR designed and …

Next Generation Exa-Scale Capable Software For High Fidelity Physics Aware Simulations, Ashesh Kumar Chattopadhyay

Open Access Theses & Dissertations

Physics aware simulations, often arising in problems of fluid dynamics, aerodynamics and multi-physics areas have demanded the need for computing software that has the capability to resolve the complexities at multiple scales to analyze and visualize the effects of their interactions with the surroundings. Usually the governing dynamics of these phenomenon appear in the form of complex partial differential equations whose numerical solutions impose various constraints on computational complexity, programming time and efficient throughput. In this scenario, the need of computing software that can solve very large problems resolving the physics of these phenomenon at multiple scales is imperative. Despite …

Advances In Chemical Vapor Deposition Growth Of Molybdenum Disulfide For Photodetectors And Flexible Electronics, Carlos Francisco De Anda Orea

Open Access Theses & Dissertations

The conversion of light into electrical signals is at the basis of technologies that affect our daily lives. Applications, including video imaging, optical communications, biomedical imaging, security, night-vision, gas sensing and motion detection have reached a high level of maturity due to the development of high-performance materials, large-scale production, and integration technologies. Currently conventional photodetectors made of Silicon (Si) or III-V compounds are about to reach their maximum efficiency, and every time it is harder to get a noticeable improvement in performance of sensors based on these materials, not to mention the complicated fabrication methods to achieve just a few …

Methods For Producing Graphene From Petroleum By-Products, Eva M. Deemer

Open Access Theses & Dissertations

N/A

Influence Of Overlay Thickness On Interface Bonding, Aliasghar Dormohammadi

Open Access Theses & Dissertations

Overlaying is an efficient and proven pavement preservation approach for flexible pavements. The overlay thickness varies from 1 in. to 4 in. depending on the conditions of the existing pavement, financial resources, etc. In the recent decade, financial constraints in conjunction with the push for pavement preservation, the overlay thickness is being reduced to less than an in. The ultra-thin overlay is a new cost-effective method that can be used to preserve functional pavement problems and provide satisfactory ride quality. Although studies have been conducted to evaluate pavement systems using numerical simulation, the research in the area of evaluating existing …

On-Orbit Autonomous Repair: Systems Design And Project Management Of The Orbital Factory Ii Cube-Satellite, Mike Louis Everett

Open Access Theses & Dissertations

In 2016, a group of faculty, staff and students from the University of Texas at El Paso submitted a formal entry to the ULA CubeCorp competition to launch a 1U Cube Satellite into Orbit. In September of 2016, the team was awarded a launch opportunity to a prestigious GTO orbit to test and validate electrically conductive printing on within the Van Allen Radiation belts. This Dissertation is focused upon the management plan and specific decision that were implemented to accomplish this goal within a one year time frame and on a conservative budget.

In 2018 this satellite will launch aboard …

First Level Design And System Design Of Janus Liquid Oxygen-Liquid Methane Lander, Jahir Fernandez

Open Access Theses & Dissertations

Taking humans to space has always been a fantastic feat, but taking humans to another planet in our solar system is the new goal. Technology has come a long way and with that, so has our knowledge of space and what can be done with current technology to accomplish our goal. These technologies allow for a more efficient space system to transport future astronauts using liquid oxygen and liquid methane (LO2-LCH4) as propellants. This combination of propellants, LO2-LCH4, brings a variety of benefits. One of the main advantages is that they can be recovered or created from local resources, using …

Development Of Post-Pareto Optimality Methods For Multiple Objective Optimization, Juan Valentin Fernandez

Open Access Theses & Dissertations

In the past years, multiple objective optimization has been considered, as an important research area since in many real life problems there exists multiple criteria that need to be optimized simultaneously. The use of evolutionary algorithms or metaheuristic methods as solution methodologies lead to a large number of Pareto solutions rather than a single unique optimum. This Pareto-optimal set most of the time tends to be very large and the decision maker now faces the challenge of reducing its size to analyze a feasible number of solutions, thus deciding the best possible solution. In this work, two methods will be …

Behavior Of Sandwich Composite Cores Under Extreme Conditions, Carlos Daniel Garcia Perez

Open Access Theses & Dissertations

The use of composite structures for diverse applications have become of great interest for scientists and engineers thanks to the advantages that they may offer in comparison to conventional materials. In the case of sandwich composite structures, its mechanical properties can be tailored according to the necessities through the correct selection of a core and facesheets. In combination, this "new" material will have superior properties compared to traditional materials such as steel and aluminum. For arctic exploration, a core with low moisture absorption, low density, and resistance to extreme, low temperatures is desirable for this type of application. This Thesis …

On Demand 3d Printed Hybrid Scaffolds For Tissue Engineering Applications, Ivan D. Hernandez

Open Access Theses & Dissertations

A composite 3D printed polymer scaffold with inbuilt porosity and filled with a hydrogel can provide an ideal support system for cell growth, proliferation, and vascularization. Therefore, a hybrid system of 3D printed polycaprolactone (PCL) scaffold and a hydroxyapatite-based hydrogel was developed for application in the reconstruction of bone defects, which are inherently difficult to repair without any guided therapies. In the present study, a 3D printed gyroid structure of PCL allowed the loading of a higher amount of hydrogel as compared to conventionally used 3D printed mesh structure of the same volume and strut thickness. The hydrogel was composed …

Quantifying The Characteristic Length Of A Combustor For An Ionic Liquid Monopropellant Thruster, Kimberly Marie Hogge

Open Access Theses & Dissertations

Ionic liquid monopropellants are currently being researched as a promising alternative to hydrazine in propulsion systems. This report presents a flame study that delineates the flame length of the expected decomposition products from an ionic liquid monopropellant. Through these studies, the characteristic length of a combustion chamber will be defined through calculations and empirical correlations. There is limited information on designing a propulsion system for an ionic liquid monopropellant. Therefore, defining the magnitude for an effective characteristic length serves as beneficial in designing a propulsion system for an ionic liquid monopropellant thruster.

Ac Susceptibility And Epr Investigations Of Superspin Dynamics In Manganese Oxide Nanoparticles, Mahesh Koirala

Open Access Theses & Dissertations

We have investigated the superspin dynamics of 5 nm and 10 nm mixed state Mn3O4 nanoparticles utilizing ac-susceptibility and electron paramagnetic resonance measurements. The out of phase component of the ac-susceptibility measurements show a magnetic anomaly below (T

Cost-Effective Recovery Of Concentrated Cooling Tower Blowdown Using The Cerro Process, Lindsey Nicole Larson

Open Access Theses & Dissertations

The Concentrate Enhanced Recovery Reverse Osmosis (CERRO) process is a seawater-RO unit that can cost-effectively achieve extremely high recoveries from water high in silica, carbonate and sulfate concentrations. This relatively new technology takes advantage of the induction time of potential foulants to recover more water than what is normally achievable with a conventional desalination system. The scope of the project was to evaluate the efficiency of the CERRO process as a pilot study using cooling tower blowdown which varied in water quality parameters daily. It was found that the CERRO pilot could successfully achieve 85% recovery, and the main limitation …