Engineering Commons^™

Frequency Response Reduced Order Model Of Primary Resonance Of Electrostatically Actuated Mems Circular Plate Resonators, Dumitru I. Caruntu, Reynaldo Oyervides

Mechanical Engineering Faculty Publications

This paper deals with the amplitude-frequency response of soft AC electrostatically actuated MEMS clamped circular plates. Alternating Current (AC) frequency is near half natural frequency of the plate. This results in primary resonance of the system. Two methods are used and compared, namely the Method of Multiple Scales (MMS), and Reduced Order Model (ROM). Both methods are in excellent agreement for amplitudes less than 0.4 of the gap. For amplitudes between 0.4 and 1 of the gap only seven terms ROM accurately predicts the behavior of the system. The effects of the voltage and damping parameters on the frequency response …

Removal Of Organic Micro-Pollutants From Water Using Sewage Sludge Based Composite Adsorbents, Rui Ding

Dissertations, Theses, and Capstone Projects

Millions of tons of sewage sludge, waste oil sludge and fish waste are produced annually, and improper treatment/disposal of these wastes have resulted in numerous environmental issues. On the other hand, these wastes are rich in organic materials, metals, and inorganic minerals and could be sustainable resources if utilized properly. The main purpose of this dissertation study was, therefore, to convert these wastes into composite adsorbents, and then use these adsorbents to remove various types of organic pollutants, emerging organic contaminants in particular, from wastewater and drinking water sources.

It is hypothesized that a hydrophobic carbon phase in the composite …

Reversible Control Of The Magnetization Of Fe₃O₄ Via Lithium Ions, Guodong Wei, Lin Wei, Dong Wang, Yufeng Tian, Yanxue Chen, Shishen Yan, Liangmo Mei, Jun Jiao

Mechanical and Materials Engineering Faculty Publications and Presentations

In this report, a reversible control of Fe₃O₄ saturated magnetization by Li ions is demonstrated. A miniature Li ion battery (LIB) was assembled using a Fe₃O₄ nanoparticle layer as the active cathode. A stable magnetism modulation is realized by a nondestructive electrochemical process in which the lithium insertion results in a valence change and partial redistribution of Fe cations in the crystal structure. The relation between the discharge voltage and the chemical phases were studied by ex situ X-ray diffraction and magnetic measurement. In a suitable discharge potential range, a reversible control of Fe₃O₄ saturated magnetization was obtained without structural …

The Bridge Newsletter Spring 2017, Missouri University Of Science And Technology

The Bridge Newsletter

-Bayless retires
-Lifesaving flood relief
-Asphalt expert joins S&T
-First Prakash Lecture

A Novel Tantalum-Containing Bioglass. Part Ii. Development Of A Bioadhesive For Sternal Fixation And Repair, Adel Mf Alhalawani, Cina Mehrvar, Wendy Stone, Stephen D. Waldman, Mark R. Towler

Chemical and Biochemical Engineering Faculty Research & Creative Works

With over a million median sternotomy surgeries performed worldwide every year, sternal wound complications have posed a serious risk to the affected patients. A rigid therapeutic sternal fixation device has therefore become a necessity. In this work, the incorporation of up to 0.5 mol% of tantalum pentoxide (Ta₂O₅), in exchange for zinc oxide (ZnO), into the SiO₂-ZnO-CaO-SrO-P₂O₅ glass system is presented. The effect of Ta incorporation on the physical, chemical and biological properties of the glass polyalkenoate cements (GPCs) prepared from them have been presented in this manuscript. The data obtained …

Online Algorithms For Content Caching: An Economic Perspective, Ammar Gharaibeh

Dissertations

Content Caching at intermediate nodes, such that future requests can be served without going back to the origin of the content, is an effective way to optimize the operations of computer networks. Therefore, content caching reduces the delivery delay and improves the users’ Quality of Experience (QoE). The current literature either proposes offline algorithms that have complete knowledge of the request profile a priori, or proposes heuristics without provable performance. In this dissertation, online algorithms are presented for content caching in three different network settings: the current Internet Network, collaborative multi-cell coordinated network, and future Content Centric Networks (CCN). Due …

Sparsity Based Methods For Target Localization In Multi-Sensor Radar, Haley H. Kim

Dissertations

In this dissertation, several sparsity-based methods for ground moving target indicator (GMTI) radar with multiple-input multiple-output (MIMO) random arrays are proposed. MIMO random arrays are large arrays that employ multiple transmitters and receivers, the positions of the transmitters and the receivers are randomly chosen. Since the resolution of the array depends on the size of the array, MIMO random arrays obtain a high resolution. However, since the positions of the sensors are randomly chosen, the array suffers from large sidelobes which may lead to an increased false alarm probability. The number of sensors of a MIMO random array required to …

Assessment Of A Hand Exoskeleton On Proximal And Distal Training In Virtual Environments For Robot Mediated Upper Extremity Rehabilitation, Kevin Abbruzzese

Dissertations

Stroke is the leading cause of disability in the United States with approximately 800,000 cases per year. This cerebral vascular accident results in neurological impairments that reduce limb function and limit the daily independence of the individual. Evidence suggests that therapeutic interventions with repetitive motor training can aid in functional recovery of the paretic limb. Robotic rehabilitation may present an exercise intervention that can improve training and induce motor plasticity in individuals with stroke. An active (motorized) hand exoskeleton that provides support for wrist flexion/extension, abduction/adduction, pronation/supination, and finger pinch is integrated with a pre-existing 3-Degree of Freedom (DOF) haptic …

Development Of Low Alloy Steel By Direct Metal Laser Sintering, Elias Jelis

Dissertations

The US Department of Defense is interested in developing, understanding, and optimizing process parameters for low alloy (4340/4140 steel) for the powder bed fusion process. Low alloy steel is used in parts where high strength and toughness are required. During parameter optimization, several aspects of the process are investigated. Powder size and morphology optimization is important for manufacturability because adequate packing is required to produce full density components. Microstructure evaluation is used in order to provide insight into parameters that lead to optimal mechanical performance and recoating performance. Influence of residual stress is evaluated with this process. Large thermal stress …

Usu Seeks Computer Science Department Head | College Of Engineering, Usu College Of Engineering

College of Engineering News

Utah State University seeks applications for the Head of the Department of Computer Science in the College of Engineering.

Denoising Techniques Reveal Neural Correlates Of Modulation Masking Release In Auditory Cortex, Sahil Chaubal

Theses

Hearing aids allow hearing impaired (HI) individuals to regain auditory perception in quiet settings. However, despite advances in hearing aid technology, HI individuals do not perform as well in situations with background sound as normally hearing (NH) listeners. An extensive literature demonstrates that when comparing tone detection performance in background noise, NH listeners have better thresholds when that noise is temporally modulated as compared to temporally unmodulated. However, this perceptual benefit, called Modulation Masking Release (MMR), is much reduced in HI listeners, and this is thought to be a reason for why HI listeners struggle in the presence of background …

Source-Channel Coding For Coordination Over A Noisy Two-Node Network, Sarah A. Obead

Theses

Recently, the concept of coordinating actions between distributed agents has emerged in the information theory literature. It was first introduced by Cuff in 2008 for the point-to-point case of coordination. However, Cuff’s work and the vast majority of the follow-up research are based on establishing coordination over noise-free communication links. In contrast, this thesis investigates the open problem of coordination over noisy point-to-point links. The aim of this study is to examine Shannon’s source-channel separation theorem in the context of coordination. To that end, a general joint scheme to achieve the strong notion of coordination over a discrete memoryless channel …

Heat Transfer In Silicon - Experiments And Simulation, Chihlin Huang

Theses

The purpose of this thesis is to study the heat transfer in silicon. Silicon is the key semiconductor material, and thermal processing is the traditional method that is used in semiconductor processing. In this research, we can predict the temperature of the silicon wafer during heating. This ability to predict wafer temperature during semiconductor processing will facilitate in the following: (a) Process temperature uniformity, (b) Film thickness uniformity, (c) Diffusion, (d) Process yield, (e) Thermally induced stresses, and (f) Device yield - spatially and temporally across the wafer. For low temperature applications, IC chips can be modeled to simulate the …

Electrical, Electronic And Optical Properties Of Mose2 And Wse2, Sushant Shashikant Rassay

Theses

Transition-metal dichalcogenides (TMDC) crystals have emerged as a new class of semiconductors that display distinctive properties at monolayer thickness. Their electrical, electronic and optical properties are of particular interest and importance for applications in optoelectronics as light emitters, detectors, and photovoltaic devices. Monolayer MoSe₂ and WSe₂ have an intrinsic band-gap in the visible region of the solar spectrum (400nm - 700nm) which makes them distinct from other 2-D materials like graphene.

In this study, the electrical, electronic and optical properties of monolayer and bulk MoSe₂ and WSe₂ are studied. The electronic band structures are presented for …

Novel Experimental Method For The Determination Of The Minimum Agitation Speed For Solids Suspension In Flat-Bottomed Stirred Tank Reactors, Shriarjun Shastry

Theses

Knowledge of the minimum agitation speed, Njs, required to suspend finely divided solids in vessels stirred by an impeller is a critical parameter to properly operate industrial tanks in a large number of industrial operations. The most common experimental approach to measure N_js is that of Zwietering’s (Chem. Eng. Sci., 1958, 8, 244-253), consisting of visually inspecting the tank bottom and visually determining the impeller agitation speed at which the solids are observed to rest on the tank bottom for no more than 1-2 seconds before being swept away. This method is quite reliable, but a method …

Electrical, Electronic And Optical Properties Of Mos2 & Ws2, Weitao Tang

Theses

Two dimensional materials such as graphene, boron nitride and transition metal dichalcogenide (TMDCs) monolayers have arisen as a new class of materials with unique properties at monolayer thickness. Their electrical, electronic and optical properties are of great importance for a variety of applications in optoelectronics as light emitters, detectors, and photovoltaic devices. This work focuses on MoS₂ and WS₂, which are two important members of the TMDC class of materials. The properties of monolayer MoS₂ and WS₂ are investigated as well as the properties of bulk MoS₂ and WS₂ to provide an understanding …

Eis Analysis Of Shear Enhanced Microfluidic Lab-On-A-Chip Device, Mehnaz Mursalat

Theses

Electrochemical sensors and biosensors have received much attention owing to the feasibility demonstrated regarding instrumental simplicity, decent cost, and portability during the detection of a wide range of biological and pharmaceutical macromolecules. Carbon-based nanomaterials, including carbon nanotubes, have garnered tremendous interest for their unique thermal, mechanical, electronic and catalytic properties while designing these sensors. Whenever the macromolecules interact with a bio-recognition element on the electrode transducer surface, a measurable change in the electrical current or potential takes place. To achieve lower limits of detection, the use of sensor surfaces modified with nanostructured materials such as nanotubes, or nanoparticles is becoming …

Real Time, Integrated, Paper Based Temperature Sensor For Lab On A Chip Device, Vignesh Shekhar

Theses

Temperature measurement and manipulation is a critical factor in a wide range of applications like Point Of Care Diagnostics (POC's), Polymerase Chain Reaction (PCR), Temperature Gradient Focusing (TGF) to cite few prominent examples. In the past decade, researchers have used various techniques to sense and control the temperature in microfluidic systems. The primary challenge has been the twin problem of integration and accuracy using minimal equipment while keeping it simple. In this study, an equipment free fabrication of the temperature sensor using filter paper impregnated with p-type colloidal PbS quantum dots is demonstrated. This sensor is later integrated into line …

Synchronous Generation And Coherent Control Of Extreme Wavelength Radiation And Ultrafast Spectroscopy, Aram Gragossian

Optical Science and Engineering ETDs

Recent progress in ultrafast laser science has made it possible to synthesize and control complex electromagnetic waveforms down to sub-femtosecond timescales. These tailored ultrashort laser pulses can generate coherent bursts of electromagnetic radiation in the extreme ultraviolet (XUV) and terahertz spectral regions with durations reaching the attosecond regime in the XUV region. This is accomplished by coherently controlling electronic motion in gas plasma targets. With these novel radiation sources, ultrafast time-resolved spectroscopy can be performed on a large variety of materials. Knowledge of the spectral phase of an ultrashort pulse is crucial for many applications. There are a variety of …

2017 Spring Engr333 Project Assignment, Matthew K. Heun

ENGR 333

The Spring 2017 ENGR333 project focused on campus energy consumption.

I asked the students “Can you construct a fine-grained, bottom-up electricity demand model that predicts the annual electricity consumption for the dormitories (section A) and the PE complex (section B) for each year of the last decade with an accuracy of ±2%?”

Customer

The customer for this project was Jack Phillips, Assistant Director (Mechanical) at Calvin’s Physical Plant.

Structure And Physical Properties Of Srniru5O11 Single Crystals: An R-Type Ferrite Based On Ordered Kagome Nets, L. Shlyk, Lance E. De Long, R. Niewa

Physics and Astronomy Faculty Publications

Single crystals of the R-type ferrite SrNiRu₅O₁₁ were grown from a chloride flux. The hexagonal crystal structure contains ruthenium located on distorted kagome nets. The low-temperature dc magnetic susceptibilities (χ_⊥ and χ_∥, perpendicular and parallel to the c axis, respectively) diverge as T^−0.3, and do not exhibit any indication of long-range magnetic order down to 4.5 K. The electrical resistivity varies as T^1.6 below 40 K, which is typical of non-Fermi liquids, and may originate from a competition between residual magnetic interactions among Ni²⁺ (S = 1) spins …

Field-Induced Formation And Growth Of Pillars On Films Of Bisphenol-A-Polycarbonate, Yu-Fan Chuang, Jyun-Siang Peng, Fuqian Yang, Donyau Chiang, Sanboh Lee

Chemical and Materials Engineering Faculty Publications

An electric field is used to construct pillars on films of bisphenol-A-polycarbonate (BPAPC) between two parallel electrodes. Both the size and density of the pillars are dependent on the film thickness. For the same experimental conditions, thicker films will lead to the formation of pillars of larger sizes and smaller densities. The time dependence of the average diameter of the pillars is found to be a linear function of the square root of the difference between the annealing time and incubation time. The temperature dependence of the temporal evolution of the pillars follows the Arrhenius relation with an activation enthalpy …

Multiscale Mechanistic Characterization Of Reclaimed Asphalt Pavements, A. M. Feroze Rashid

Student Theses and Dissertations

The Superpave test methods are based on unmodified asphalt binders and mixes; researchers have reported limitations of these methods in evaluating modified binders. An Atomic Force Microscope (AFM) has the potential to determine morphology and nanomechanistic properties of modified and unmodified asphalt binders. In this study, different amounts of binders recovered from four selected reclaimed asphalt pavements (RAP) are blended with a virgin Performance Grade (PG) binder and tested by following Superpave tests and AFM techniques. Binders with high RAP are found to have more rutting resistance than the virgin binder but less cracking resistance due to their brittleness. Toward …

Performance Evaluation Of Polyphosphoric Acid Modified Asphalt Binders, Istiaque Mahmud

Student Theses and Dissertations

The objective of this study was to find out short- and long-term performance of Polyphosphoric Acid (PPA)-modified asphalt binders. To evaluate the binder performance, mechanistic, chemical and moisture susceptibility tests were done on PPA- and Styrene Butadiene Styrene (SBS)-modified asphalt binders. Mechanistic performance was analyzed by Superpave performance grade testing (AASHTO M 320), whereas chemical analysis was done by Fourier Transform Infrared Spectroscopy (FTIR) analyses and moisture susceptibility was evaluated by Surface Free Energy (SFE) techniques. Superpave testing results suggest that PPA-modified binders are more rutting and fatigue resistant than PG 64-22 binders, but use of Liquid Anti-Stripping Agents (LAA) …

Wire Neutralization System, Scott A. Bradley, Jason Wiitanen, Timothy B. Smigowski, John T. Niemeyer, Andrew Culkin

Michigan Tech Patents

A wire neutralizing system for use with a vehicle including a frame adapted to be hitched to a vehicle. At least one wheel supports the frame while a bottom of the wheel rolls over terrain having buried wires. The system also includes a blade movable between a stowed position in which the blade is above the bottom of the wheel and a deployed position in which the blade is below the bottom of the wheel, such that the blade plows through the terrain to disable buried wires when in the deployed position.

Impact Factor And Scholarly Research: The Traditional Media With A Social Media Influence, Brent D. Bowen, Jacqueline Luedtke, Timothy B. Holt, David Ehrensperger, Hunter M. Watson

Publications

The research method for this project – examining the dissemination of research artifacts through social media as well as the impact social media can have on scholarly research – originated with Dr. Brent Bowen of Embry-Riddle Aeronautical University at the Prescott, Arizona campus and Dr. Dean E. Headley of Wichita State University. Drs. Bowen and Headley introduced the Airline Quality Rating (AQR) in early 1991 as an objective method for comparing and scoring airline performance in areas deemed to be important for consumers. Scores are calculated by defining 15-elements in four major areas, focusing on airline performance and the significance …

Airline Quality And The Consumer Perception, Brent D. Bowen, Erin Bowen, Dean E. Headley, Madeline S. Kuhn

Publications

Operational performance of the U.S. airline industry has been monitored for the past 27 years by a quantitative model of metrics known as the Airline Quality Rating. The National Airline Quality Rating (http://airlinequalityrating.com) sets the industry standard for comparing performance quality among U.S. airlines. Criteria included in the Airline Quality Rating (AQR) report are screened to meet two basic elements: (1) they must be readily obtainable from published data sources for each airline, and (2) they must be important to consumers regarding airline quality. Results from this report are retrieved from the April 2016 Airline Quality Rating Report.

Modelling Fatigue For Management Decision Making: A Case Study, Rajee Olaganathan, Timothy B. Holt, Jacqueline Luedtke

Publications

Fatigue is one major contributing factor that reduces the human ability and leads to accidents, and threatens the safety of aircraft and human lives.

Though fatigue is seen in all the disciplines associated with the aviation industry, this paper will discuss only pilot fatigue. Based on the literature examined, this study first examines the significance of the problem.

Investigation of the inflight, pre/post flight countermeasures (both pharmacological and non - pharmacological methods) practiced at present, discusses the Fatigue Risk Management System (FRMS) – in this first, it defines the FRMS, briefly discusses its history, describes the organizational structure of FRMS …

The Utilization Of Peer Mentorship And Its Positive Impact On Student Retention, Timothy B. Holt, Jacqueline Luedtke, Claire Schindler

Publications

In recognition of increasing rates of repeated ground schools and flight lessons, in combination with decreasing retention rates in the flight programs at Embry-Riddle Aeronautical University, the Department of Aeronautical Science in the College of Aviation took initiative to create a program that identified struggle students before they reached excessive failure or financial distress. The students identified in the Student Success Initiative (SSI) after being assessed would be required to attend a mediation session with their academic and flight training staff in order to create a specialized training program.

• Student Success Initiative (SSI)
• Identifies "at risk" students
• Implemented training plan …

The Effects Of Using Noise Reduction Turbofan Engine Nozzle Designs On A Turbojet Engine, Donald Bartlett

Journal of Applied Sciences and Arts

Abstract

Aircraft noise is a complex topic which is projected to increase with the increasing number of aircraft and size of the engines. Turbine-powered aircraft produce sounds that are considered pollutants at certain decibel levels. Turbofan engines are inherently quieter than turbojet engines for a given level of thrust. The purpose of this research is to determine if current turbofan noise reduction nozzles could reduce the amount of noise for turbojet engines at two different thrust levels. Three turbofan engine nozzles were designed and tested on a turbojet engine. Decibel levels of 30 frequencies for each of the nozzles were …