Engineering Commons^™

On Dual-Band Amplifications Using Dual Two-Tones: Clarifications And Discussion, Siyuan Yan, Xianzhen Yang, Xiao Li, Fu Lo

Electrical and Computer Engineering Faculty Publications and Presentations

A significant development of recent research in nonlinear distortion is the expansion of the conventional two-tone test for power amplifiers to the concurrent dual-band transmitters, by Amin et al. A general framework using dual two-tones is developed, which shows that the output signal is affected not only by intermodulation (IM) products but also by cross-modulation (CM) products. In this paper, we will make a number of clarifications to Amin et al.'s paper. The effects of IM and CM in passband will be discussed, IM represents a reduction for compressive devices, and CM reflects an interference caused by the signal from …

Water Resources Adaptation To Climate And Demand Change In The Potomac River, James H. Stagge, Glenn E. Moglen

Publications

The effects of climate change are increasingly considered in conjunction with changes in water demand and reservoir sedimentation in forecasts of water supply vulnerability. Here, the relative effects of these factors are evaluated for the Washington, DC metropolitan area water supply for the near (2010 to 2039), intermediate (2040-2069), and distant future (2070 to 2099) by repeated water resources model simulations. This system poses water management challenges due to long water delivery travel times that increase uncertainty, multiple water jurisdictions that constrain potential decisions, and future scenarios that simultaneously increase demand and decrease water supply during the critical summer period. …

Atmospheric Processes Affecting The Separation Of Volcanic Ash And So < Inf> 2 In Volcanic Eruptions: Inferences From The May 2011 Grímsvötn Eruption, Fred Prata, Mark Woodhouse, Herbert E. Huppert, Andrew Prata, Thor Thordarson, S. Carn

Michigan Tech Publications, Part 1

The separation of volcanic ash and sulfur dioxide (SO2) gas is sometimes observed during volcanic eruptions. The exact conditions under which separation occurs are not fully understood but the phenomenon is of importance because of the effects volcanic emissions have on aviation, on the environment, and on the earth's radiation balance. The eruption of Grímsvötn, a subglacial volcano under the Vatnajökull glacier in Iceland during 21-28 May 2011 produced one of the most spectacular examples of ash and SO2 separation, which led to errors in the forecasting of ash in the atmosphere over northern Europe. Satellite data from several sources …

A Carbon Nanotube Optical Reporter Maps Endolysosomal Lipid Flux, Jena V. Prakrit, Daniel E. Roxbury, Thomas V. Galassi, Leila Akkari, Christopher P. Horoszko, David B. Iaea, Januka Budhathoki-Uprety, Nina Pipalia, Abigail S. Haka, Jackson D. Harvey, Jeetain Mittal, Frederick R. Maxfield, Johanna A. Joyce, Daniel A. Heller

Chemical, Biomolecular, and Materials Engineering Faculty Publications

Lipid accumulation within the lumen of endolysosomal vesicles is observed in various pathologies including atherosclerosis, liver disease, neurological disorders, lysosomal storage disorders, and cancer. Current methods cannot measure lipid flux specifically within the lysosomal lumen of live cells. We developed an optical reporter, composed of a photoluminescent carbon nanotube of a single chirality, that responds to lipid accumulation via modulation of the nanotube’s optical band gap. The engineered nanomaterial, composed of short, single-stranded DNA and a single nanotube chirality, localizes exclusively to the lumen of endolysosomal organelles without adversely affecting cell viability or proliferation or organelle morphology, integrity, or function. …

Increasing Atmospheric Humidity And Co2 Concentration Alleviate Forest Mortality Risk, Yanlan Liu, Anthony J. Parolari, Mukesh Kumar, Chang-Wei Huang, Gabriel Katul, Amilcare Porporato

Civil and Environmental Engineering Faculty Research and Publications

Climate-induced forest mortality is being increasingly observed throughout the globe. Alarmingly, it is expected to exacerbate under climate change due to shifting precipitation patterns and rising air temperature. However, the impact of concomitant changes in atmospheric humidity and CO₂ concentration through their influence on stomatal kinetics remains a subject of debate and inquiry. By using a dynamic soil–plant–atmosphere model, mortality risks associated with hydraulic failure and stomatal closure for 13 temperate and tropical forest biomes across the globe are analyzed. The mortality risk is evaluated in response to both individual and combined changes in precipitation amounts and their seasonal …

Evaluation Of Stability Of Unit Loads For Tilt And Shock Events During Distribution, Jay Singh, Koushik Saha, Tyler Sewell

Journal of Applied Packaging Research

Initiatives to lightweight and reduce packaging materials to achieve sustainability goals have created unit load stability challenges in the transportation and handling of palletized packaged goods. Consequently, an increased focus is being placed on evaluating how current pre-shipment performance tests evaluate load stability. This study was undertaken to address the current need for establishing test methodologies towards observing a unit load’s overall stability during transportation and handling related activities commonly experienced in the distribution environment. With this goal, this study developed two test methods as well as apparatus/measuring tool to observe a palletized load’s overall stability. The experimentation involved unit …

The Advent Of University-Level Packaging Scholarship: The Time, The Place And The People, Diana Twede, Laura Bix

Journal of Applied Packaging Research

In 1952, Michigan State College (MSC), now Michigan State University (MSU), was the first university in the world to offer a Bachelor of Science degree in Packaging. Other universities had previously offered related courses like canning (as part of a food science degree) or military packaging (in wartime), but MSU was the first to propose packaging as its own academic field of scholarship.

Other universities followed, sharing faculty and curriculum models developed at MSU. As a result, graduates’ careers in packaging now have a higher professional status, and universities play a key role in developing our international community of packaging …

Damping Package Design Using Structural Corrugated Board, Qi Zhang, Katsuhiko Saito, Katsushige Nagaoka

Journal of Applied Packaging Research

Packaging is designed to protect products from shock and vibration during transport. In recent years, paper cushioning materials, such as corrugated board and pulp molded packaging, are being increasingly used because they are environmentally friendly and easy to recycle. However, because no efficient packaging-design method yet exists for paper cushioning material, packaging engineers must rely on previous experience and the so-called trial-and-error method to design packaging. One reason for this situation is that, for most cases, the paper cushioning material used for protective packaging has a complicated structure and deforms after being subjected to repetitive shock and vibration. To address …

Development Of Starch-Polyvinyl Alcohol (Pva) Biodegradable Film: Effect Of Cross-Linking Agent And Antimicrobials On Film Characteristics, Aniket Satish More, Chandani Sen, Madhusweta Das

Journal of Applied Packaging Research

To satisfy the need of developing eco-friendly flexible antimicrobial packaging film with minimum use of synthetic chemical ingredients, the present study examined the efficacy of citric acid (CA) as cross-linking agent and essential oils (EOs), viz., cinnamon essential oil (CEO) and oregano essential oil (OEO) as natural antimicrobials in corn starch-polyvinyl alcohol (CS-PVA) film. Compared to film prepared from filmogenic solution (FS) containing 75 kg CS+8.75 kg PVA+24.6 kg glycerol per m³ FS, film additionally containing CA at 0.07 kg/kg CS indicated 95% higher ultimate tensile strength (UTS) and 27% lower water vapor permeability (WVP). Film developed with incorporation …

Combating The Problem Of Smuggling Via Legal Refugee Transport Agencies, Mitchell Maurer (Engineering), Ala Saleh, Alex Marino, Adam Hoover, Imani Pajibo, Gabriel De Toro Cruzat

Nexus Maximus

Our final project is the idea of an organization that works to legally transport refugees into the EU where they can safely become members of the local economy. Legal and social loopholes prevent refugees from entering easily, while refugees are actually seen to aid in temporary working economies.

Nexus Maximus IV

The Challenge: Innovation for Refugees and Displaced Populations

One of the great challenges of our time is how to help refugees and displaced populations, and how to prevent the causes in the first place. Every minute, 24 people around the world are forced to flee their homes. That’s 34,000 …

A Novel Real-Time Non-Invasive Hemoglobin Level Detection Using Video Images From Smartphone Camera, Golam Mushih Tanimul Ahsan, Md. O. Gani, Md Kamrul Hasan, Sheikh Iqbal Ahamed, William Chu, Mohammad Adibuzzaman, Joshua Field

Electrical and Computer Engineering Faculty Research and Publications

Hemoglobin level detection is necessary for evaluating health condition in the human. In the laboratory setting, it is detected by shining light through a small volume of blood and using a colorimetric electronic particle counting algorithm. This invasive process requires time, blood specimens, laboratory equipment, and facilities. There are also many studies on non-invasive hemoglobin level detection. Existing solutions are expensive and require buying additional devices. In this paper, we present a smartphone-based non-invasive hemoglobin detection method. It uses the video images collected from the fingertip of a person. We hypothesized that there is a significant relation between the fingertip …

Cross-Correlation-Based Structural System Identification Using Unmanned Aerial Vehicles., Hyungchul Yoon, Vedhus Hoskere, Jong-Woong Park, Billie F. Spencer

Michigan Tech Publications, Part 1

Computer vision techniques have been employed to characterize dynamic properties of structures, as well as to capture structural motion for system identification purposes. All of these methods leverage image-processing techniques using a stationary camera. This requirement makes finding an effective location for camera installation difficult, because civil infrastructure (i.e., bridges, buildings, etc.) are often difficult to access, being constructed over rivers, roads, or other obstacles. This paper seeks to use video from Unmanned Aerial Vehicles (UAVs) to address this problem. As opposed to the traditional way of using stationary cameras, the use of UAVs brings the issue of the camera …

Theory And Applications Of Plasmonically Active Spherical And Core-Shell Nanoparticles, Mohammad Habibur Rahaman

Student Theses and Dissertations

Optical properties of metal nanoparticles and core-shell nanoparticles are related to their plasmon response. Plasmonic resonance is the collective oscillations of conduction electrons in metal. The core-shell nanoparticles represent unique geometry and plasmonic resonance can be tuned either by changing the distance between core-shell nanoparticle or by changing their core to shell ratio. This work focuses on the theoretical design of single and multiple core-shell nanoparticles for exploring the resonance properties of core-shell nanoparticles using scattering theory. The results provide new and tunable optical properties of core-shell nanoparticles that solid single or multiple metal nanoparticles can not demonstrate. We have …

Mechanical And Economical Impacts Of Adding Polymers Into Asphalt Mixtures, Mena Souliman, Waleed Zeiada, Lubinda Walubita

Civil Engineering Faculty Publications and Presentations

Load associated fatigue cracking is one of the major distress types occurring in flexible pavements. Flexural bending beam fatigue laboratory test has been used for several decades and is considered an integral part of the Superpave advanced characterization procedure. One of the most significant solutions to sustain the fatigue life for an asphaltic mixture is to add sustainable materials such as polymers to the asphalt mixture. A laboratory testing program was performed on two gap-graded mixtures: unmodified and polymer-modified asphalt mixtures. Strain controlled fatigue tests were conducted according to the AASHTO T321 procedure. The results from the beam fatigue tests …

An Optical Probe For Detecting Chondrocyte Apoptosis In Response To Mechanical Injury, Yihui Huang, Jun Zhou, Amirhossein Hakamivala, Jinglei Wu, Yi Hong, Joseph Borrelli Jr., Liping Tang

Bioengineering Faculty Publications - Archive

Cartilage injury induced by acute excessive contact stress is common and mostly affects young adult. Although early detection of cartilage injury may prevent serious and lifelong arthritic complications, early detection and treatment is not possible due to the lack of a reliable detection method. Since chondrocyte injury and subsequent cell death are the early signs of cartilage injury, it is likely that cartilage cell apoptosis can be used to predict the extent of injury. To test this hypothesis, a near infrared probe was fabricated to have high affinity to apoptotic cells. In vitro tests show that this apoptosis probe has …

Making Software, Making Regions: Labor Market Dualization, Segmentation, And Feminization In Austin, Portland And Seattle, Dillon Mahmoudi

Dissertations and Theses

Through mixed-methods research, this dissertation details the regionally variegated and place-specific software production processes in three second-tier US software regions. I focus on the relationship between different industrial, firm, and worker production configurations and broad-based economic development, prosperity, and inequality. I develop four main empirical findings.

First, I argue for a periodization of software production that tracks with changes in software laboring activity, software technologies, and wage-employment relationships. Through a GIS-based method, I use the IPUMS-USA to extensively measure the amount and type of software labor in industries across the US between 1970 and 2015. I map the uneven geography …

Reference Data Set Of Volcanic Ash Physicochemical And Optical Properties, A. Vogel, S. Diplas, A. J. Durant, A. S. Azar, M. F. Sunding, William I. Rose, A. Sytchkova, C. Bonadonna, K. Krüger, A. Stohl

Department of Geological and Mining Engineering and Sciences Publications

Uncertainty in the physicochemical and optical properties of volcanic ash particles creates errors in the detection and modeling of volcanic ash clouds and in quantification of their potential impacts. In this study, we provide a data set that describes the physicochemical and optical properties of a representative selection of volcanic ash samples from nine different volcanic eruptions covering a wide range of silica contents (50–80 wt % SiO₂). We measured and calculated parameters describing the physical (size distribution, complex shape, and dense-rock equivalent mass density), chemical (bulk and surface composition), and optical (complex refractive index from ultraviolet to …

Specifying And Testing Fiber Reinforced Shotcrete: Advances And Challenges, Antoine Gagnon, Marc Jolin

Shotcrete for Underground Support XIII: New Developments in Rock Engineering, Tunneling, Underground Space and Deep Excavation

Although fiber reinforced shotcrete (FRS) has been around for many years in the tunneling and mining industry, there are still difficulties in many areas to bring owners and specifiers to take full advantage of the properties of this material in their ground support programs. These difficulties are often associated with the fact that the technical information or material properties reported (such as energy absorption or cracking load) do not necessarily reflect the actual need of the ground support engineer. The paper first proposes an overview, and comparison, of the various methods used to characterize FRS. It then moves on and …

A Bayesian Estimation Model For Transient Engine Exhaust Characterization Using Fourier Transform Infrared Spectroscopy, David Wilson, Casey Allen

Mechanical Engineering Faculty Research and Publications

Comprehensive emissions models extensively use engine exhaust data from vehicle experiments to represent the relationship between fuel composition and pollutants. However, the predicted emissions from these models often neglect the effects of transients and speed-load history. Fourier transform infrared (FTIR) spectroscopy is a high frequency measurement technique capable of comprehensive speciation. However, due to long residence times of exhaust within a FTIR spectrometer gas cell, FTIR measurements are contaminated by the effects of historical emissions, precluding the attainment of time-resolved engine exhaust data. This work presents a Bayesian estimation model for processing FTIR measurements to obtain accurate estimations of instantaneous …

Micro-Contacts Testing Using A Micro-Force Sensor Compatible With Biological Systems, Ronald A. Coutu Jr., Dushyant Tomer

Electrical and Computer Engineering Faculty Research and Publications

This paper presents the performance and reliability testing of microelectromechanical systems (MEMS) switches by using a micro-force sensor which was originally designed/used to conduct mechanical testing of biological cells. MEMS switches are key components for radio frequency (RF) applications due to their extremely low power consumption and small geometries over conventional technologies. However, unstable electrical contact resistance severely degrades the performance and reliability of such micro-switches. Therefore, our focus is to improve the performance and reliability of “cold” switched micro-contacts by using novel contact materials and engineered micro-contact surfaces. The contact metallurgies considered in this work are “similar” thin film …

Design And Planned Obsolescence. Theories And Approaches For Designing Enabling Technologies, Matteo Zallio, Damon Berry

Articles

We are currently living in a decade where smart objects and Internet of Things (IoT)-based devices are becoming part of daily life in different contexts. This research seeks to investigate and verify, by using a formal literature review methodology, the most visible aspects of technological development, within the Industry 4.0 and IoT scenario, in relation to the theories of the so called “Planned Obsolescence”.

This study covers a defined number of works on Design theories and practices on how to face the issue of built-in obsolescence of devices in the era of the Connected Devices. The majority of the works …

Concrete Renovation And Enhancing Of Fire Protection Of An Existing Tunnel With Sprayable Polymer Cement Concrete (Spcc), Stefan Peters, U. Versen, Stefan Peters

Shotcrete for Underground Support XIII: New Developments in Rock Engineering, Tunneling, Underground Space and Deep Excavation

The approx. 342 m long tunnel located in the old town is constructed as a two cell rectangular frame section as part of the L530 in Lüdenscheid in 1971. During the stocktaking process it was detected that the demands of technical standards like e.g. RBT, ZTV-ING, RIZ-ING are not met. The construction also lacks of the structural fire protection. A recalculation of the rectangular frame section in case of exposure to fire showed that there is no sufficient load capacity. Due to the location in the city center with construction work above the tunnel line this topic is of major …

Be Capstone Design Students Sample Scofield Reservoir: Harmful Algal Blooms | Sustainable Waste-To-Bioproducts Engineering Center, Usu College Of Engineering

College of Engineering News

Identifying, harvesting, and treating harmful algae blooms (HABs) is the ultimate goal of the BE Capstone Design team for 2017.

Evaluation Of Heat Available From Calcium Chloride Desiccant Hydration Reaction For Domestic Heating In San Francisco, Ca, Michael Giglio

Mechanical Engineering Master's Theses

Thermochemical energy storage has the potential to support the use of solar thermal energy collection in ways that traditional thermal energy storage, like sensible and latent heat storage, have fallen short. Thermochemical energy storage has been shown to have higher storage capacities than sensible and latent storage for dehumidifying applications and does not require insulation like sensible and latent heating do. Sensible heating is focused on maintaining an increased temperature of a storage medium while latent heat storage is focused on maintaining a phase of the storage material. Both sensible and latent heat storage have been shown to have lower …

2017 Fall Engr333 Project Assignment, Matthew K. Heun

ENGR 333

The Fall 2017 ENGR333 project focused on campus energy cost savings.

I asked the students two questions:

• Section A: What would it take for Calvin to save $75k/year on natural gas costs?
• Section B: What would it take for Calvin to save $150k/year on energy costs (mostly electricity) using a new on-site co-gen plant?

Customer

The customer for this project was Phil Beezhold, Director of Calvin’s Physical Plant.

Optimal Cultivation Pattern To Increase Revenue And Reduce Water Use: Application Of Linear Programming To Arjan Plain In Fars Province, Amin Daghighi, Ali Nahvi, Ungtae Kim

Civil and Environmental Engineering Faculty Publications

Because the available water resources of the Arjan plain region in Iran do not fully meet the watering requirements for plants in farmlands, the crops suffer from water stress, a situation that causes them to wilt. The aim of this study is to develop a water resources planning model that helps decision-makers determine an appropriate cultivation pattern, optimize the exploitation from surface water resources, and specify the method of allocating water across different farm crops to minimize the detrimental effects of water shortage. Through investigating various models of water resources planning and properties along with the governing conditions for each …

The Social Acceptance Of Community Solar: A Portland Case Study, Anne Weaver

Dissertations and Theses

Community solar is a renewable energy practice that's been adopted by multiple U.S. states and is being considered by many more, including the state of Oregon. A recent senate bill in Oregon, called the "Clean Electricity and Coal Transition Plan", includes a provision that directs the Oregon Public Utility Commission to establish a community solar program for investor-owned utilities by late 2017. Thus, energy consumers in Portland will be offered participation in community solar projects in the near future. Community solar is a mechanism that allows ratepayers to experience both the costs and benefits of solar energy while also helping …

Information Technology News, Georgia Southern University

Information Technology: News & Publications (2012-2023)

• Jennifer Marsman to Present Using EEG and Machine Learning to Perform Lie Detection

Multi Layered Shotcrete Design For Tunnel Construction, Matthias Werner Beisler, Sebastian Höser, Vladimir Bartos

Shotcrete for Underground Support XIII: New Developments in Rock Engineering, Tunneling, Underground Space and Deep Excavation

Shotcrete linings have been applied successfully for a large number of tunnel constructions within the last couple of decades all around the world. While up to the 1980’s the structural design of the shotcrete linings mainly was based on experience gathered throughout the construction and some simplified analyses in the following years the application of the Finite Element Method lead to much more sophisticated design and more accurate estimation of deformations and stress state in the shotcrete lining. This was amongst others achieved by considering the time and construction sequence - dependent development of the deformations as well as by …

Impact Of Polymer Binders On The Pull-Out Force Of Macro-Synthetic Fibers In Sprayed Concrete, Klaus Bonin, Christina Neumaier

Shotcrete for Underground Support XIII: New Developments in Rock Engineering, Tunneling, Underground Space and Deep Excavation

The standard test used to characterize the performance of a fiber-reinforced sprayed concrete is the round or square panel test. Steel and macro synthetic fibers with different physical properties are commonly used as reinforcement. The test panel is usually prepared by spraying shotcrete into a steel mold and, after curing, performing a three-point bending test. The difficulty of this kind of preparation is to know where the fibers are located and how many have remained in the sample. There are plenty of factors affecting the fiber distribution, such as the type of shotcrete, wet or dry mix preparation and application …