Engineering Commons^™

Synthesis Of Single-Hole Vibration Waveforms From A Mining Blast, Lifeng Li

Theses and Dissertations--Mining Engineering

In mining engineering, blast-induced ground vibration has become one of the major concerns when production blasts are conducted, especially when the mining areas and the blast sites are near inhabited areas or infrastructure of interest. To comply with regulations, a vibration monitoring program should be developed for each mining operation. The vibration level, which is usually indicated by the peak particle velocity (PPV) of the vibration waveform, should fall below the maximum allowable values. Ideally, when blasting is near structures of interest (power towers, dams, houses, etc.), the vibration level (PPV) should be predicted prior to the actual production blasts. …

Thermo-Mechanical Coupling For Ablation, Rui Fu

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to investigate the thermal stress and expansion as well as the associated strain effect on material properties caused by high temperature and large temperature gradient, a two-way thermo-mechanical coupling solver is developed. This solver integrates a new structural response module to the Kentucky Aerothermodynamics and Thermal response System (KATS) framework. The structural solver uses a finite volume approach to solve either hyperbolic equations for transient solid mechanics, or elliptic equations for static solid mechanics. Then, based on the same framework, a quasi-static approach is used to couple the structural response and thermal response to estimate the thermal expansion …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Wing-Tip Vortex Evolution In Turbulence, Hari Charan Ghimire

Theses and Dissertations--Mechanical and Aerospace Engineering

Planar and stereo particle image velocimetry measurements were conducted of a wing-tip vortex decaying in free-stream turbulence in order to understand the evolution of a vortex and its decay mechanism. The vortex decayed faster in the presence of turbulence. The decay of the circulation was found to be almost entirely due to a decrease in circulation of the vortex core, caused by the relative decrease in peak tangential velocity without a corresponding increase in core radius. These events were found to be connected with the stripping of core fluid from the vortex core. The increased rate of decay of the …

Characterization Of The Shape Memory Behavior Of High Strength Nitihfpd Shape Memory Alloys, Guher P. Toker

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf alloys have emerged as potential materials for applications requiring high transformation temperatures (> 100 °C) with high strength and work output. Although they have high transformation temperatures, their low damping capacity, brittleness and poor superelastic responses (of Ti-rich NiTiHf) impedes their wider usage in many industrial applications. In this study, the quaternary alloying element of Pd has been added to NiTiHf alloys to improve and tailor their shape memory behavior,. NiTiHfPd alloys were systematically examined regarding the composition and heat treatments effects.

Effects of substituting Hf with Ti on the shape memory behavior of NiTHfPd alloys were investigated. There …

Regression Analysis Of Factors Impacting Problem Solving Engagement Within Lean Systems Implementation, David M. Parsley Ii

Theses and Dissertations--Mechanical and Aerospace Engineering

Organizations around the world have attempted to implement the concepts of the Toyota Production System (TPS), commonly referred to as Lean, with limited sustainable success. The central principles of TPS, continuous improvement and respect for people, are grounded in the Japanese values of Monozukuri and Hitozukuri. Monozukuri deals with creating or making a product, while Hitozukuri conveys the idea of developing people through learning. In order for organizations to adopt these values they must have a system that engages employees at all levels in applying problem solving to improve their work. This research uses organizational assessments obtained from a variety …

Characterization Of Rotary Bell Atomizers Through Image Analysis Techniques, Jacob E. Wilson

Theses and Dissertations--Mechanical and Aerospace Engineering

Three methods were developed to better understand and characterize the near-field dynamic processes of rotary bell atomization. The methods were developed with the goal of possible integration into industry to identify equipment changes through changes in the primary atomization of the bell. The first technique utilized high-speed imaging to capture qualitative ligament breakup and, in combination with a developed image processing technique and PIV software, was able to gain statistical size and velocity information about both ligaments and droplets in the image data. A second technique, using an Nd:YAG laser with an optical filter, was used to capture size statistics …

Intermittency Effects On The Universality Of Local Dissipation Scales In Turbulent Boundary Layer Flows With And Without Free-Stream Turbulence, Sabah Falih Habeeb Alhamdi

Theses and Dissertations--Mechanical and Aerospace Engineering

Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Re_τ ≈ 1000 (Re_θ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions of external wall-bounded flow.

Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length-scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions, due to the imperfect characterization of the upper bound of the inertial cascade by the integral length-scale. When a length-scale based on Townsend's …

Laminar And Turbulent Study Of Combustion In Stratified Environments Using Laser Based Measurements, Stephen William Grib

Theses and Dissertations--Mechanical and Aerospace Engineering

Practical gas turbine engine combustors create extremely non-uniform flowfields, which are highly stratified making it imperative that similar environments are well understood. Laser diagnostics were utilized in a variety of stratified environments, which led to temperature or chemical composition gradients, to better understand autoignition, extinction, and flame stability behavior. This work ranged from laminar and steady flames to turbulent flame studies in which time resolved measurements were used.

Edge flames, formed in the presence of species stratification, were studied by first developing a simple measurement technique which is capable of estimating an important quantity for edge flames, the advective heat …

Scale Models Of Acoustic Scattering Problems Including Barriers And Sound Absorption, Nan Zhang

Theses and Dissertations--Mechanical and Aerospace Engineering

Scale modeling has been commonly used for architectural acoustics but use in other noise control areas is nominal. Acoustic scale modeling theory is first reviewed and then feasibility for small-scale applications, such as is common in the electronics industry, is investigated. Three application cases are used to examine the viability. In the first example, a scale model is used to determine the insertion loss of a rectangular barrier. In the second example, the transmission loss through parallel tubes drilled through a cylinder is measured and results are compared to a 2.85 times scale model with good agreement. The third example …

NoX Formation In Light-Hydrocarbon, Premixed Flames, Robert T. Hughes

Theses and Dissertations--Mechanical and Aerospace Engineering

This study explores the reactions and related species of NO_x pollutants in methane flames in order to understand their production and consumption during the combustion process. To do this, several analytical simulations were run to explore the behavior of nitrogen species in the pre-flame, post- flame, and reaction layer regions. The results were then analyzed in order to identify all "steady-state" species in the flame as well as the determine all the unnecessary reactions and species that are not required to meet a defined accuracy. The reductions were then applied and proven to be viable.

Numerical And Experimental Techniques For Assessing The Acoustic Performance Of Duct Systems Above The Plane Wave Cutoff Frequency, Kangping Ruan

Theses and Dissertations--Mechanical and Aerospace Engineering

This research deals with determining the acoustic attenuation of heating, ventilation, and air conditioning (HVAC) ductwork. A finite element approach was developed for calculating insertion loss and breakout transmission loss. Procedures for simulating the source and receiving rooms were developed and the effect of structureborne flanking was included. Simulation results have been compared with measurements from the literature and the agreement is very good. With a good model in place, the work was extended in three ways. 1) Since measurements on full-scale equipment are difficult, scale modeling rules were developed and validated. 2) Two different numerical approaches were developed for …

Characterization Of Methane-Air Diffusion Flames For Flame Synthesis Application Through Optical Diagnostics, Zhaojin Diao

Theses and Dissertations--Mechanical and Aerospace Engineering

Flame synthesis is a growing field of research aiming at forming new materials and coatings through injection of seed materials into a flame. Accurate prediction of the thermal structure of these flames requires detailed information on the radiative properties and a thorough understanding of the governing combustion processes. The objective of this work is to establish a basic optical diagnostic characterization of different methane-air diffusion flames of different complexity. The basic principles are developed and demonstrated at a rotational symmetric co-flow burner and finally applied to a burner consisting of six clustered microflames which is designed for future flame synthesis …

Bayesian-Integrated System Dynamics Modelling For Production Line Risk Assessment, Sudhir Punyamurthula

Theses and Dissertations--Mechanical and Aerospace Engineering

Companies, across the globe are concerned with risks that impair their ability to produce quality products at a low cost and deliver them to customers on time. Risk assessment, comprising of both external and internal elements, prepares companies to identify and manage the risks affecting them. Although both external/supply chain and internal/production line risk assessments are necessary, internal risk assessment is often ignored. Internal risk assessment helps companies recognize vulnerable sections of production operations and provide opportunities for risk mitigation.

In this research, a novel production line risk assessment methodology is proposed. Traditional simulation techniques fail to capture the complex …

Verification And Validation Studies For The Kats Aerothermodynamics And Material Response Solver, Olivia Schroeder

Theses and Dissertations--Mechanical and Aerospace Engineering

Modeling the atmospheric entry of spacecraft is challenging because of the large number of physical phenomena that occur during the process. In order to study thermal protection systems, engineers rely on high fidelity solvers to provide accurate predictions of both the thermochemical environment surrounding the heat shield, and its material response. Therefore, it is necessary to guarantee that the numerical models are correctly implemented and thoroughly validated. In recent years, a high-fidelity modeling tool has been developed at the University of Kentucky for the purpose of studying atmospheric entry. The objective of this work is to verify and validate this …

The Kentucky Re-Entry Universal Payload System (Krups): Sub-Orbital Flights, James Devin Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable testbed for atmosphere entry science experiments, with an initial application to thermal protection systems (TPS). Because of the uniqueness of atmospheric entry conditions that ground testing is unable to replicate, scientists principally rely on numerical models for predicting entry conditions. The KRUPS spacecraft, developed at the University of Kentucky, provides an inexpensive means of obtaining validation data to verify and improve these models.

To increase the technology readiness level (TRL) of the spacecraft, two sub-orbital missions were developed. The first mission, KUDOS, launched August 13th, 2017 on a Terrier-Improved Malamute …

Assisted Development Of Mesophase Pitch With Dispersed Graphene And Its Resulting Carbon Fibers, Aaron Owen

Theses and Dissertations--Mechanical and Aerospace Engineering

The efficacy of dispersed reduced graphene oxide (rGO) as a nucleation site for the growth of mesophase in an isotropic pitch was investigated and quantified in this study. Concentrations of rGO were systematically tested in an isotropic petroleum and coal-tar pitch during thermal treatments and compared to pitch without rGO. The mesophase content of each thermally treated pitch was quantified by polarized light point counting. Further characterization of softening temperature and insolubles were quantified. Additionally, the pitches with and without rGO were melt spun, graphitized, and tensile tested to determine the effects of rGO on graphitized fiber mechanical properties and …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Multiphase Interaction In Low Density Volumetric Charring Ablators, Ali D. Omidy

Theses and Dissertations--Mechanical and Aerospace Engineering

The present thesis provides a description of historical and current modeling methods with recent discoveries within the ablation community. Several historical assumptions are challenged, namely the presence of water in Thermal Protection System (TPS) materials, presence of coking in TPS materials, non-uniform elemental production during pyrolysis reactions, and boundary layer gases, more specifically oxygen, interactions with the charred carbon interface.

The first topic assess the potential effect that water has when present within the ablator by examining the temperature prole histories of the recent flight case Mars Science Laboratory. The next topic uses experimental data to consider the instantaneous gas …

Contributions To Hybrid Power Systems Incorporating Renewables For Desalination Systems, Nasser Alawhali

Theses and Dissertations--Electrical and Computer Engineering

Renewable energy is one of the most reliable resource that can be used to generate the electricity. It is expected to be the most highly used resource for electricity generation in many countries in the world in the next few decades. Renewable energy resources can be used in several purposes. It can be used for electricity generation, water desalination and mining. Using renewable resources to desalinate the water has several advantages such as reduce the emission, save money and improve the public health. The research described in the thesis focuses on the analysis of using the renewable resources such as …

Attitude Control On So(3) With Piecewise Sinusoids, Shaoqian Wang

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation addresses rigid body attitude control with piecewise sinusoidal signals. We consider rigid-body attitude kinematics on SO(3) with a class of sinusoidal inputs. We present a new closed-form solution of the rotation matrix kinematics. The solution is analyzed and used to prove controllability. We then present kinematic-level orientation-feedback controllers for setpoint tracking and command following.

Next, we extend the sinusoidal kinematic-level control to the dynamic level. As a representative dynamic system, we consider a CubeSat with vibrating momentum actuators that are driven by small $\epsilon$-amplitude piecewise sinusoidal internal torques. The CubeSat kinetics are derived using Newton-Euler's equations of motion. …

Discrete-Time Adaptive Control Algorithms For Rejection Of Sinusoidal Disturbances, Mohammadreza Kamaldar

Theses and Dissertations--Mechanical and Aerospace Engineering

We present new adaptive control algorithms that address the problem of rejecting sinusoids with known frequencies that act on an unknown asymptotically stable linear time-invariant system. To achieve asymptotic disturbance rejection, adaptive control algorithms of this dissertation rely on limited or no system model information. These algorithms are developed in discrete time, meaning that the control computations use sampled-data measurements. We demonstrate the effectiveness of algorithms via analysis, numerical simulations, and experimental testings. We also present extensions to these algorithms that address systems with decentralized control architecture and systems subject to disturbances with unknown frequencies.

Hydrothermal Carbonization: Modeling, Final Properties Design And Applications: A Review, Silvia Román, Judy Libra, Nicole Berge, Eduardo Sabio, Kyoung Ro, Liang Li, Beatriz Ledesma, Andrés Alvarez, Sunyoung Bae

Faculty Publications

Active research on biomass hydrothermal carbonization (HTC) continues to demonstrate its advantages over other thermochemical processes, in particular the interesting benefits that are associated with carbonaceous solid products, called hydrochar (HC). The areas of applications of HC range from biofuel to doped porous material for adsorption, energy storage, and catalysis. At the same time, intensive research has been aimed at better elucidating the process mechanisms and kinetics, and how the experimental variables (temperature, time, biomass load, feedstock composition, as well as their interactions) affect the distribution between phases and their composition. This review provides an analysis of the state of …

Electronic Drum Machine (E.D.M), Nyssa Marie Backes

Electrical Engineering

Many people argue that a drummer plays the most important role in a band of any genre. During live performances, the other band members rely on the drummer to keep the song moving forward at a proper steady pace. Even in recorded music, drums help listeners sing and dance along with their favorite songs. Thus, achieving success as a band, both in terms of recordings and live shows, absolutely requires a drummer. So, if a band does not have a drummer, and cannot afford the hefty cost of hiring a session drummer, a touring drummer, or both, how can they …

Design And Development Of A Novel Acoustic Rain Sensor With Automated Telemetry, Maria Leonora Guico, Gemalyn Abrajano, Prince Aldrin Domer, Jose Paulo Talusan

Electronics, Computer, and Communications Engineering Faculty Publications

This paper presents the recent results of the design of a novel acoustic rainfall sensing system that is low-cost, portable, and easily deployable, which makes use of the recorded sound produced by the impact of the raindrops on the sensor surface. The sensor design allows the gathering of acoustic signal power and sending it to a server after a specified time interval, either through SMS or mobile internet connection. It exists in a weather-proof, standard-conformant, standalone system with its own power supply and telemetric capabilities. These acoustic point sensors can gather rainfall data at high spatial and temporal resolutions. Such …

Comparison Of Emissions Measurement Between A Sensor-Based Compact Emissions Meter And A Standard Pems, Jordan Matthew Leatherman

Graduate Theses, Dissertations, and Problem Reports (ETD)

The emissions produced by diesel engines are detrimental to human health, and the environment. To reduce these harmful emissions, engine manufacturers have used exhaust after treatment systems. The main objective of these after-treatment systems is to reduce exhaust emissions with minimal impact on an engines performance. The increase in emission regulations resulted in the need for a portable device to measure emissions. Portable emissions measurement systems (PEMS) are used to ensure engines comply with regulations in the real world. Although these systems are portable and can be installed on a vehicle they are bulky, expensive and time consuming to install. …

On Designing An Ecg-Based Intelligent System: Utilizing The Heart’S Electrical Activity To Recognize Humans And Detect Arrhythmia, Sara Saeed Abdeldayem

Graduate Theses, Dissertations, and Problem Reports (ETD)

The electrocardiogram (ECG) signal is the bioelectrical signal that reflects the heart's activity. It has been extensively used as a diagnostic tool since it holds information about the cardiac health condition. However, recent researches have shown that it exhibits an inter-subject variability property. Therefore, it can be used as a biometric-based modality for either identification or verification purposes. Nevertheless, some of the challenges are faced while employing such a signal. For instance, ECG signal is prone to noise, accordingly, noise filters should be designed to remove the noise while keeping the signal properties. Moreover, factors such as medications, health condition, …

Enhancing Cognitive Algorithms For Optimal Performance Of Adaptive Networks, Hector Lugo-Cordero

Electronic Theses and Dissertations

This research proposes to enhance some Evolutionary Algorithms in order to obtain optimal and adaptive network configurations. Due to the richness in technologies, low cost, and application usages, we consider Heterogeneous Wireless Mesh Networks. In particular, we evaluate the domains of Network Deployment, Smart Grids/Homes, and Intrusion Detection Systems. Having an adaptive network as one of the goals, we consider a robust noise tolerant methodology that can quickly react to changes in the environment. Furthermore, the diversity of the performance objectives considered (e.g., power, coverage, anonymity, etc.) makes the objective function non-continuous and therefore not have a derivative. For these …

Energy Efficient And Secure Wireless Sensor Networks Design, Afraa Attiah

Electronic Theses and Dissertations

Wireless Sensor Networks (WSNs) are emerging technologies that have the ability to sense, process, communicate, and transmit information to a destination, and they are expected to have significant impact on the efficiency of many applications in various fields. The resource constraint such as limited battery power, is the greatest challenge in WSNs design as it affects the lifetime and performance of the network. An energy efficient, secure, and trustworthy system is vital when a WSN involves highly sensitive information. Thus, it is critical to design mechanisms that are energy efficient and secure while at the same time maintaining the desired …

Fluid Dynamics Modeling And Sound Analysis Of A Bileaflet Mechanical Heart Valve, Fardin Khalili

Electronic Theses and Dissertations

Cardiovascular disease (CVD) is one of the main causes of death in the world. Some CVD involve severe heart valve disease that require valve replacement. There are more than 300,000 heart valves implanted worldwide, and about 85,000 heart valve replacements in the US. Approximately half of these valves are mechanical. Artificial valves may dysfunction leading to adverse hemodynamic conditions. Understanding the normal and abnormal valve function is important as it help improve valve designs. Modeling of heart valve hemodynamics using computational fluid dynamics (CFD) provides a comprehensive analysis of flow, which can potentially help explain clinical observations and support therapeutic …