Engineering Commons^™

Electric Vehicle Grid Experiments And Analysis, Florida Solar Energy Center, Richard Raustad

FSEC Energy Research Center®

This project developed a low cost building energy management system (EMS) and conducted vehicle-to-grid (V2G) experiments on a commercial office building. The V2G effort included the installation and operation of a Princeton Power System CA-30 bi-directional power system. These experiments targeted the reduction of utility peak electrical demand for a commercial office building. In each case, total building peak demand was managed through a computer algorithm to limit the charging rate of electric vehicles or used the vehicle's on-board traction battery as a storage device to minimize peak electrical loads.

Fatigue Life Of Pitch- And Stall-Regulated Composite Tidal Turbine Blades, Ciaran R. Kennedy, Vesna Jaksic, Sean B. Leen, Conchúr M. Ó Brádaigh

Publications

Tidal turbine blades are subject to harsh loading and environmental conditions, including large thrust and torsional loadings, relative to wind turbine blades, due to the high density of seawater, among other factors. The complex combination of these loadings, as well as water ingress and associated composite laminate saturation, have significant implications for blade design, affecting overall device design, stability, scalability, energy production and cost-effectiveness. This study investigates the effect of seawater ingress on composite material properties, and the associated design and life expectancy of tidal turbine blades in operating conditions. The fatigue properties of dry and water-saturated glass fibre reinforced …

Preparation And Characterization Of Titanate-Phosphate Passivation Film On Tinplate, Zi-Yu Wang, Ming-Hao Wang, De-Yu Li, Ning Li

Journal of Electrochemistry

A passivation film was prepared on tinplate surface with a composite passivating agent made of titanate and phosphate. The surface morphologies, chemical compositions and corrosion resistances of the passivation films were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), salt spray test, Tafel polarization measurement and electrochemical impedance spectroscopy (EIS). The results were compared with those films untreated and treated with titanate or phosphate passivation. It was shown that the titanate and phosphate passivation film was mainly composed of Ti₃(PO₄)₄·nH₂O and TiO₂. The finely crystallized surface could seal …

Preparation And Properties Of Nanocrystalline Nickel By Pulse Electrodeposition On Glassy Carbon, Ya-Li Zhang, Ming-Xian Zhang, Teng-Da Guo, Yan-Jie Zhao, Sheng-Xue Yu

Journal of Electrochemistry

Nanocrystalline nickel exhibits electrocatalytic activity for methanol. In this work, nanocrystalline nickel coating has been obtained by using the double pulse method on glassy carbon materials surface. The influence of pulse conditions on the grain size of nanocrystalline nicke was studied. The concentrations and compositions of the plating bath were  300 g·L^-1 NiSO₄·6H₂O,45 g·L^-1 NiCl₂·6H₂O,40 g·L^-1 H₃BO₃,5 g·L^-1 C₇H₅NO₃S,and 0.05 g·L^-1 C₁₂H₂₅NaO₄S. The optimal pulse process parameters including the average pulse …

Synthesis And Electrochemical Properties Of Nickel-Rich Cathode Material Lini0.6Co0.2Mn0.2O2 With High Initial Coulombic Efficiency, Xiao-Yun Guan, Chao-Yu Hong, Jian-Ping Zhu, Wei-Li Wang, Yi-Xiao Li, Yong Yang

Journal of Electrochemistry

Nickel-rich cathode materials LiNi_0.6Co_0.2Mn_0.2O₂(NCM622)were synthesized by a co-precipitation-solid state sintering method at different temperatures. The structure, morphology and electrochemical performance of the as-prepared materials were investigated by X-ray powder diffraction (XRD) /Rietveld refinement, scanning electron microscope (SEM) and electrochemical experiments. It is found that NCM622 calcined at 800 ℃ showed the lowest degree of cation disorder (~1.97%) with a high initial Coulombic effiency of 92.2% and the capacity retention of 81.4% after 100 cycles.

Electrodeposition Of Cigs Thin Film With Special Structure Using Laser Etching Template, Jin-Zhi Yu, Ye Lian, Jin-Qiu Zhang, Pei-Xia Yang, Mao-Zhong An

Journal of Electrochemistry

Copper indium gallium selenide (Cu_1.00In_xGa_1-xSe_2.00, CIGS) thin film solar cells have a wide application in semiconductor thin film batteries. The CIGS absorbing layer is the key of the thin film solar cell material. Therefore, it is of theoretical and practical significance to carry out researches in CIGS thin films. In this work, the CIGS thin films with special structures were prepared by using laser etching template. The copper thin film was firstly electrodeposited in aqueous solution with Laser etching template. The influences of temperature, current and concentration of copper sulfate on morphology …

An Electrochemical Investigation In The Anticorrosive Properties Of Silver Nanoparticles For The Acidic Corrosion Of Aluminium, H. A. Fetouh, B. A. Abd-El-Nabey, Y. M. Goher, M. S. Karam

Journal of Electrochemistry

The mass loss, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques were used for the determinations of the corrosion rates for aluminium in 1.0 mol·L^-1 hydrochloric acid (HCl) solutions both in the absence and presence of silver nanoparticles (SNPs) at 30 ℃. The protection efficiency was evaluated to be 96.4% for 0.014 g·L^-1 of the SNPs. It has been found that the capacity of the electrical double layer at the aluminium/solution interface was decreased with increasing the concentration of the SNPs, indicating that the SNPs were adsorbed at the aluminium surface. The Langmuir adsorption isotherm and the kinetic-thermodynamic …

Preface For Special Issue On Electroplating And Surface Finishing, Mao-Zhong An

Journal of Electrochemistry

/

Combinations Of Plant Water-Stress And Neonicotinoids Can Lead To Secondary Outbreaks Of Banks Grass Mite (Oligonychus Pratensis Banks), Alice Ruckert, L. Niel Allen, Ricardo A. Ramirez

Civil and Environmental Engineering Faculty Publications

Spider mites, a cosmopolitan pest of agricultural and landscape plants, thrive under hot and dry conditions, which could become more frequent and extreme due to climate change. Recent work has shown that neonicotinoids, a widely used class of systemic insecticides that have come under scrutiny for non-target effects, can elevate spider mite populations. Both water-stress and neonicotinoids independently alter plant resistance against herbivores. Yet, the interaction between these two factors on spider mites is unclear, particularly for Banks grass mite (Oligonychus pratensis; BGM). We conducted a field study to examine the effects of water-stress (optimal irrigation = 100% …

Advancing Distributed Data Management For The Hydroshare Hydrologic Information System, Hong Yi, Ray Idaszak, Michael Stealey, Chris Calloway, Alva L. Couch, David G. Tarboton

Civil and Environmental Engineering Faculty Publications

HydroShare (https://www.hydroshare.org) is an online collaborative system to support the open sharing of hydrologic data, analytical tools, and computer models. Hydrologic data and models are often large, extending to multi-gigabyte or terabyte scale, and as a result, the scalability of centralized data management poses challenges for a system such as HydroShare. A distributed data management framework that enables distributed physical data storage and management in multiple locations thus becomes a necessity. We use the iRODS (Integrated Rule-Oriented Data System) data grid middleware as the distributed data storage and management back end in HydroShare. iRODS provides a unified virtual file system …

The Suitability Of Zn–1.3% Fe Alloy As A Biodegradable Implant Material, Alon Kafri, Shira Ovadia, Jeremy Goldman, Jaroslaw W. Drelich, Eli Aghion

Michigan Tech Publications, Part 1

Efforts to develop metallic zinc for biodegradable implants have significantly advanced following an earlier focus on magnesium (Mg) and iron (Fe). Mg and Fe base alloys experience an accelerated corrosion rate and harmful corrosion products, respectively. The corrosion rate of pure Zn, however, may need to be modified from its reported ~20 µm/year penetration rate, depending upon the intended application. The present study aimed at evaluating the possibility of using Fe as a relatively cathodic biocompatible alloying element in zinc that can tune the implant degradation rate via microgalvanic effects. The selected Zn–1.3wt %Fe alloy composition produced by gravity casting …

Numerical Simulation Of Energy Localization In Dynamic Materials, Arkadi Berezovski, Mihhail Berezovski

Publications

Dynamic materials are artificially constructed in such a way that they may vary their characteristic properties in space or in time, or both, by an appropriate arrangement or control. These controlled changes in time can be provided by the application of an external (non-mechanical) field, or through a phase transition. In principle, all materials change their properties with time, but very slowly and smoothly. Changes in properties of dynamic materials should be realized in a short or quasi-nil time lapse and over a sufficiently large material region. Wave propagation is a characteristic feature for dynamic materials because it is also …

Superhydrophobic Surface On Aluminum Alloy By Hydrothermal Method And Its Electrochemical Performance, Xiao-Hang Chen, Mo-Jing Chen, Yu-Lin Min, Qun-Jie Xu

Journal of Electrochemistry

Superhydrophobic film formed on a metal surface is an effective way for corrosion protection. In this paper, the superhydrophobic film was prepared on the surfaces of aluminum alloy by hydrothermally treating with a solution containing CeCl₃·7H₂O and CO(NH₂)₂ , and a self-assemble process. The electrochemical measurements and surface morphology results confirmed that the best superhydrophobicity and electrochemical performance could be achieved with the contact angle of 155.5^o after six hours of hydrothermal reaction. Furthermore, the inhibition efficiency of 99.6% was obtained in 3.5 wt% NaCl aqueous solution, indicating the excellent corrosion resistance …

Intrinsic Kinetic Properties Of Ternary Material For Lithium Ion Batteries Assessed By Single Particle Microelectrode, Yi-Min Wei

Journal of Electrochemistry

Electrochemical performances such as capacity, rate, cycle and thermal stability of the nickel (Ni), cobalt (Co) and manganese (Mn) ternary cathode material, LiNi_xCo_yMn_zO₂ (x + y + z = 1), are significantly influenced by the proportion of Ni, Co, and Mn elements. To obtain higher specific capacity, LiNi_0.6Co_0.2Mn _0.2O₂ (NCM622) and LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811) with high amounts of Ni element were employed for the lithium ion batteries. By now, many studies have been focusing on the thermal and cycling stabilities of …

Preparation And Electrocatalytic Activity Of Nitrogen-Doping Tungsten Carbide Catalyst, Pian-Pian Yang, Li-Zhen Huang, Ying-Ying Li, Mei-Qin Shi, Chun-An Ma

Journal of Electrochemistry

Tungsten carbide (WC) is a promising electrocatalyst, however, its electrocatalytic activity is far inferior to Pt and Pt-group metal. In this work, nitrogen-doping tungsten carbide (WN|WC) catalysts with a nanoplate morphology were prepared via the tungsten nitride (WN) as the precursor and sodium tungstate as the tungsten source. The SEM and TEM results indicated that carbon atoms entered into the WN lattice to form the hexagonal close packed WC phase. In this way, an atomic scale heterostructure involving the closely linked interfaces between WN and WC was created . The XRD data confirmed that the cubic crystal structure of WN …

Deposition Mechanism And Coating Characterization For The Trivalent Chromium Electrodeposition In Sulphate Electrolyte, Hui Yan, Shuai-Shuai Huang, Fang-Zu Yang, Zhong-Qun Tian, Shao-Min Zhou

Journal of Electrochemistry

Linear sweep voltammetry (LSV) and cyclic voltammetry (CV) were used to study the electrodeposition mechanism of trivalent chromium on a copper electrode in the novel sulphate electrolyte for thick trivalent chromium plating. The thickness, morphology, composition, microhardness, and structure, as well as the corrosion resistance in 3.5wt% NaCl solution of the trivalent chromium coatings were investigated by X-ray fluorescence gage, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), microhardness tester, X-ray diffraction (XRD) and Tafel curve measurements. The results showed that the electrodeposition of trivalent chromium involved two consecutive one electron reduction steps. The first step, Cr³⁺ + e …

Surface Ehancement Of Nickel Ions On Cyanide Free Immersion Gold Deposited From A Chloroauric Acid-Choline Chloride Solution On Medium-Phosphorus Nickel, Tian-Yu Xu, Shi-Ying Wang, Wen-Chang Wang, Zhi-Dong Chen

Journal of Electrochemistry

The nickel ions (Ni²⁺) were introduced into choline chloride (ChCl) cyanide free immersion gold solution to improve the surface quality of electrodeposition on medium-phosphorus nickel substrate. The addition of Ni²⁺ had no significant impact on the plating speed. However, the hyperactive corrosion of nickel substrate could be effectively alleviated by the addition of 500 mg·L^-1 NiCl₂·6H₂O, and the surface morphology of gold coating could be greatly improved. The choline chloride bath has great potential for industrial production due to its high Ni²⁺ carrying capacity (2000 mg·L^-1) and superior applicability …

Applications Of Electrospinning In Lithium-Air Batteries, Yue Fu, Jin Wang, Hai-Yang Yu, Jing-Hua Tian, Rui-Zhi Yang

Journal of Electrochemistry

Lithium-air batteries have received increasing attention as the “ultimate batteries” due to their extremely high theoretical capacity and environment friendly. However, there are still many obstacles hindering the wide applications of the lithium-air batteries owing to the limitations of large charge-discharge over-potentials, poor Columbic efficiency and cycling performance. Exploring of high-efficiency, low-cost and eco-friendly catalysts is one of the vital issues for lithium-air batteries. Meanwhile, electrospinning techniques have been under substantial developments due to its simple fabrication process, high efficiency and production. This paper reviews the recent progresses in fabrications of various novel catalysts for lithium-air batteries with electrospinning techniques, …

Usu Engineering Faculty Partners With National Federation Of The Blind To Develop Non-Visual Teaching Methods | College Of Engineering, Usu College Of Engineering

College of Engineering News

A researcher at Utah State University is developing non-visual techniques to teach the fundamentals of engineering to students who are blind or low vision.

Information Technology News, Georgia Southern University

Information Technology: News & Publications (2012-2023)

• Georgia Southern ranked No. 8 on the 2018 Military Times 10 Best Cybersecurity Programs list

The 3d Stress-Tensor Bootstrap, Anatoly Dymarsky, Filip Kos, Petr Kravchuk, David Poland, David Simmons-Duffin

Physics and Astronomy Faculty Publications

We study the conformal bootstrap for 4-point functions of stress tensors in parity-preserving 3d CFTs. To set up the bootstrap equations, we analyze the constraints of conformal symmetry, permutation symmetry, and conservation on the stress-tensor 4-point function and identify a non-redundant set of crossing equations. Studying these equations numerically using semidefinite optimization, we compute bounds on the central charge as a function of the independent coefficient in the stress-tensor 3-point function. With no additional assumptions, these bounds numerically reproduce the conformal collider bounds and give a general lower bound on the central charge. We also study the effect of gaps …

Developing Pennycress ( Thlaspi Arvense ) As A Biodiesel Feedstock Crop And Plant Model System, Michaela Mcginn

Theses and Dissertations

Thlapsi arvense L. (pennycress) is currently being developed as a profitable oilseed-producing winter annual cover crop with extreme cold tolerance and a rapid life cycle that can be grown on fallow farmland throughout the U.S. Midwest Corn Belt, controlling soil erosion and nutrient runoff while serving as an additional source of income for the American farmer without displacing food crops. The research comprising this dissertation demonstrates that pennycress can serve as a user-friendly model system highly similar to Arabidopsis thaliana, and is well-suited for both laboratory and field experimentation, being readily employable in existing growth facilities. After 10 generations of …

Research Benefits For Scholarly Authors Being Published On A Public Forum, Hunter M. Watson, Brent D. Bowen, Timothy B. Holt, Jacqueline R. Luedtke

Publications

The previous construct of research was focused on social media platforms as a benefactor in broadcasting towards a global audience with non-academic professions. Following along the same ideology, this research directs the attention to a pertained audience in academic profession.

•Embry-Riddle is the host of Scholarly Commons which collects the research of authors (faculty members), and assists in developing a digital portfolio. This portfolio creates metric measurements on a dashboard to indicate where downloads are occurring, and aids in providing current information pertaining to the authors’ publication. •In this case, the publication of the National Airline Quality Rating (AQR) ( …

Symmetric Equations For Evaluating Maximum Torsion Stress Of Rectangular Beams In Compliant Mechanisms, Guimin Chen, Larry L. Howell

Faculty Publications

There are several design equations available for calculating the torsional compliance and the maximum torsion stress of a rectangular cross-section beam, but most depend on the relative magnitude of the two dimensions of the cross-section (i.e., the thickness and the width). After reviewing the available equations, two thickness-to-width ratio independent equations that are symmetric with respect to the two dimensions are obtained for evaluating the maximum torsion stress of rectangular cross-section beams. Based on the resulting equations, outside lamina emergent torsional joints are analyzed and some useful design insights are obtained. These equations, together with the previous work on symmetric …

Development Of A Liquid Contacting Method For Investigating Photovoltaic Properties Of Pbs Quantum Dot Solids, Vitalii Alekseevich Dereviankin

Dissertations and Theses

Photovoltaic (PV) devices based on PbS quantum dot (QD) solids demonstrate high photon-to-electron conversion yields. However, record power conversion efficiencies remain limited mainly due to bulk and interfacial defects in the light absorbing material (QD solids). Interfacial defects can be formed when a semiconductor, such as QD solid, is contacted by another material and may predetermine the semiconductor/metal or semiconductor/metal-oxide junction properties. The objective of the work described in this dissertation was set to explore whether electrochemical contacting using liquid electrolytes can provide sufficient means of contacting the QD solids to investigate their PV performance without introducing the unwanted interfacial …

Screening Algorithm Based On The Color Halftone Fluorescent Printing And Its Application In Packaging Design, Hu Yaojian, Liu Juan, Wang Ruojing, Zhong Yunfei

Journal of Applied Packaging Research

Abstract：This paper analyzed the characteristics of colorless fluorescent ink and the existing color separation theory, so that colored additive method should be used in printing color pattern with colorless fluorescent ink as well as three-color screening separation type (red, green and blue). Considering the exhibition of the tone, this paper selected dot parallel screening method. At the same time, through comparing the properties of different dots, this paper adopted a special method of AM screening, using regular triangle as the basic dot model to a threshold matrix of AM screening. Finally, designing a screening algorithm which best suit the …

Upending Assumptions In Engineering Education | College Of Engineering, Usu College Of Engineering

College of Engineering News

It doesn’t make Idalis Villanueva uncomfortable to confront assumptions.

Three Dimensional View Of Arbitrary Q Syk Models, Sumit R. Das, Aminik Ghosh, Antal Jevicki, Kenta Suzuki

Physics and Astronomy Faculty Publications

In [15] it was shown that the spectrum and bilocal propagator of SYK model with four fermion interactions can be realized as a three dimensional model in AdS₂ ×S¹/Z₂ with nontrivial boundary conditions in the additional dimension. In this paper we show that a similar picture holds for generalizations of the SYK model with q-fermion interactions. The 3D realization is now given on a space whose metric is conformal to AdS₂ × S¹/Z₂ and is subject to a non-trivial potential in addition to a delta function at the center of …

A Longitudinal Analysis On The Cyclical Pattern Of The U.S. Airline Industry, Michelle M. Bennett, Brent D. Bowen, Jacqueline R. Luedtke, Dean Headley, Timothy B. Holt

Publications

The Airline Quality Rating (AQR) is the nation’s most comprehensive study of airline performance and quality for over two decades. AQR provides consumers and industry watchers a means to compare performance quality among different US airlines using objective performance-based data. This research looks to analyze the cyclical patterns present in AQR in order to identify trends and factors contributing to the changes in these results each year. This research utilizes the application of a longitudinal analysis methodology which will provide the correlation between factors identified and the indicators affected.

Respirable Dust Monitoring In Construction Sites And Visualization In Building Information Modeling Using Real-Time Sensor Data, Nour Smaoui, Kyungki Kim, Omprakash Gnawali, Young-Joo Lee, Wonho Suh

Durham School of Architectural Engineering and Construction: Faculty Publications

Construction activities, involving cutting, drilling, and grinding of materials, often produce toxic respirable dust that can cause fatal diseases and illnesses. To protect workers from breathing excessive amounts of respirable dust at job sites, superintendents should continuously monitor the level of respirable dust in workspaces and make timely interventions for overexposed workers. However, current practices of respirable dust monitoring have critical drawbacks, and superintendents cannot accurately estimate workers’ exposures to respirable dust or make prompt decisions to protect the workers. Therefore, there is a need for real-time air dust monitoring that can be deployed ubiquitously at a construction site and …