Engineering Commons^™

Predictive Modeling On Mineral Redistribution Of Blended Coal During Pulverized Coal Combustion, Md Saifujjaman

Student Theses and Dissertations

This paper represents an analytical model for predicting mineral redistribution (MR) of coal blending during pulverized coal (PC) combustion in a pulverized coal-fired boiler. The objective of this research is to investigate the impact of fuel quality on MR. A MATLAB code was developed in modular approach for MR of coal blending from MR of single coal based on linear weighted average method. The MR of single coal sub-module calculates mass fraction of four major mineral oxides after combustion for default and alternative size ranges by using proximate analysis, Malvern analysis, Computer Controlled Scanning Electron Microscopy (CCSEM) analysis and composition …

The Influence Of Shared Mobility And Transportation Policies On Vehicle Ownership, Edgar Bertini Ruas

PSU Transportation Seminars

With the emergence of several new providers of shared mobility services, such as Uber, Biketown and Car2go, there has been the promise of changes to the traditional way of owning and using a vehicle. One potential consequence of the new mobility services is the reduction in vehicle ownership. At the same time, cities are trying to anticipate these changes by reducing the amount of space dedicated to parking. This thesis aims to asses the extent to which new shared mobility and transportation policy strategies (especially parking requirements and transit pass availability) relate to vehicle ownership among residents of multifamily dwellings. …

Mems Variable Area Capacitor For Room Temperature Electrometry, George C. Underwood, Tod V. Laurvick

Faculty Publications

This paper introduces a new way to detect charge using MEMS variable capacitors for extremely sensitive, room temperature electrometry. It is largely based on the electrometers introduced by Riehl et al. [1] except variable capacitance is created by a changing area, not a changing gap. The new scheme will improve MEMS electrometers by eliminating the effects of squeeze-film damping and by theoretically increasing the maximum charge resolution by 70%. The charge conversion gain (the increase in output voltage per input unit charge) for this system is derived. The result show good agreement with MATLAB calculations.

Ncer Assistance Agreement Annual Progress Report For Grant #83582401 - Assessment Of Stormwater Harvesting Via Manage Aquifer Recharge (Mar) To Develop New Water Supplies In The Arid West: The Salt Lake Valley Example, Ryan Dupont, Joan E. Mclean, Richard C. Peralta, Sarah E. Null, Douglas B. Jackson-Smith

Civil and Environmental Engineering Faculty Publications

The goals of the original proposed project remain the same, that is, to test the hypothesis that Managed Aquifer Recharge (MAR) for stormwater harvesting is a technically feasible, socially and environmentally acceptable, economically viable, and legally feasible option for developing new water supplies for arid Western urban ecosystems experiencing increasing population, and climate change pressures on existing water resources. The project is being carried out via three distinct but integrated components that include: 1) Monitoring of existing distributed MAR harvesting schemes involving a growing number of demonstration Green Infrastructure (GI) test sites; 2) Integrated stormwater/vadose zone/groundwater/ ecosystem services modeling; and …

Analysis Of Casting Defect, Tensile Strength, And Hardness Of Al-Si Casting Alloy With Percentage Variation Of Clay Binder Bangkalan, Imam Muhtarom, Sunomo Sunomo

Journal of Mechanical Engineering Science and Technology (JMEST)

Casting is one of method that used in forming the work piece by melting specific metal and pouring into moulding that has been prepared. This study aimed to determine the effect of the use of Bangkalan clay as binder in sand moulding against tensile strength, hardness, and defects in Al-Si casting alloy by using gravity casting method. The method used in this study was experimental method then using descriptive analysis. Descriptive analysis included explanation of the test result of tensile strength, hardness, and the type of surface defect of Al-Si casting. Based on the research result obtained the highest shear …

Analysis Of Hardness, Quality And Fluidity Al-Si Casting Result By Using Clamshell (Placuna Placenta) As The Mixture Of Sand Moulding, Shikh Mohd Shahrul Nizan Shikh Zahari, Saif Aziz Saputra, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Metal is an element that cannot be separated from human life. Almost all of human activities includes metal element in it. Metals can be formed through several ways, one of which is metal casting. Metal casting is one of technique in producing products where the metal was melted in crucible and then poured in a moulding which is similar to the original shape of the product. Moulding that are commonly used are sand moulding. Commonly, binder which used in sand casting process is bentonite. Bentonite, was kind of mineral which can be run out during its usage. This study aimed …

The Analysis Of Permeability And Mechanical Properties Of Sand Moulding Using Mixed Material Clamshell (Placuna Placenta) On Sand Casting, Kritchakhris Nawettanaprasert, Zakaria Bagus Aminanta, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

This study objected to determine mechanical properties of sand moulding by conducting tensile test, compressive and shear test, and also permeability test. This study also had the other objective that was analyse clamshell (Placuna placenta) as mixture material for bentonite as binder in manufacturing sand moulding in order to reduce the usage of bentonite. The method that used in this study was pre-experimental method with One-Shot Case Study model. The best mechanical properties obtained on sample 3 clamshell 11%, permeability results obtained was 190 ml/min, tensile strength results obtained for the dry sand was 0.015 kg/cm2, compressive strength obtained for …

Mechanical Engineering News, Georgia Southern University

Mechanical Engineering: News & Publications (2013-2023)

• Open Assistant Professor Position, Search 67645

“How Is My Child’S Asthma?” Digital Phenotype And Actionable Insights For Pediatric Asthma, Utkarshani Jaimini, Krishnaprasad Thirunarayan, Maninder Kalra, Revathy Venkataramanan, Dipesh Kadariya, Amit Sheth

Publications

Background: In the traditional asthma management protocol, a child meets with a clinician infrequently, once in 3 to 6 months, and is assessed using the Asthma Control Test questionnaire. This information is inadequate for timely determination of asthma control, compliance, precise diagnosis of the cause, and assessing the effectiveness of the treatment plan. The continuous monitoring and improved tracking of the child’s symptoms, activities, sleep, and treatment adherence can allow precise determination of asthma triggers and a reliable assessment of medication compliance and effectiveness. Digital phenotyping refers to moment-by-moment quantification of the individual-level human phenotype in situ using data from …

Asic Design To Support Low Power High Voltage Power Supply For Radiation Monitoring Applications, Daniel Rogge

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A low power high voltage power supply is designed for use in a long duration radiation monitoring system. The supply employs a flexible pulse frequency modulation switching controller implemented in a 0.35 $\mu$m CMOS technology. The controller drives and regulates a flyback transformer driven 12-stage Cockroft-Walton voltage multiplier chain. The chain provides bias for the dynodes of a photomultiplier tube. The supply voltage is selectable via a 12-bit on-chip digital to analog converter. The system is designed for low power operation and immunity to supply voltage variation as the application is battery-powered.

Advisors: Sina Balkir and Michael W. Hoffman

Cost Performance Index Stability: Insights From Environmental Remediation Projects, Denis S. Clayson, Edward D. White, Alfred E. Thal Jr.

Faculty Publications

The purpose of this study was to investigate the stability of the cost performance index (CPI) for environmental remediation projects as the topic is not addressed in the literature. CPI is defined as the earned value of work performed divided by the actual cost of the work, and CPI stability represents the point in time in a project after which the CPI varies by less than 20 percent (measured in different ways).

Ion Exchange For Nutrient Recovery Coupled With Biosolids-Derived Biochar Pretreatment To Remove Micropollutants, Yiran Tong, Lee K. Kimbell, Anna Avila, Patrick J. Mcnamara, Brooke K. Mayer

Civil and Environmental Engineering Faculty Research and Publications

Wastewater, especially anaerobic treatment effluent, contains high ammonia nitrogen (NH₄-N) and inorganic orthophosphate (PO₄-P), which necessitate additional treatment to meet stringent discharge regulations. Ion exchange regeneration is a process that can be adopted for not only removing but also recovering nutrients. However, recovering nutrients by ion exchange from nutrient-rich effluents that also contain micropollutants (which typically pass through anaerobic treatment as well) may result in subsequent problems, since micropollutants could end up in ion exchange effluent, regenerant, or recovered fertilizer products. Micropollutant removal by a nonselective adsorbent, such as biosolids-derived biochar, before nutrient recovery processes would …

Automated Control System For Photo-Bioreactor, Madankrishna Acharya

Posters-at-the-Capitol

At the University of Kentucky Center for Applied Energy Research, recent efforts have been made to optimize and reduce the cost of a unit designed to control an automated photobioreactor system in which microalgae is grown to reduce CO2 emissions. In contrast with a previously used system based on a compactRIO controller and NI LabVIEW software, a new optimized version utilizes an inexpensive Beagle Bone panel as a microcontroller that can be programmed through the use of Python software. Notably, the cost of the new control system was 1/10th of the price of the previous unit.

Bubbly Water Makes An Abnormal Splash | College Of Engineering, Usu College Of Engineering

College of Engineering News

Researchers at Utah State University are splashing soapy water to unveil new discoveries within fluid dynamics.

Cell For Flow Battery, Jonghyun Park, Mohammed Abdulkhabeer Al-Yasiri

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A reaction cell for a flow battery having flow channels positioned within a recess of a non-porous and non-brittle housing that is also a dielectric. Positioning the flow channels within the recess eliminates the need for end plates, gaskets, and insulators of conventional designs. A current collector and an electrode within the recess have areas approximately equal to the area of the recess such that they fit within the recess and maximize the contact area between them.

Assessing The Mean Neuronal Firing Rate Information Hypothesis Via Mutual Information, Greg W. Zdor

Honors Theses

While it is currently well accepted that the mean neuronal firing rate (MNFR) is a key parameter encoding information about sensory and motor events, in some cases the measured information due to MNFR is not adequate to explain the total neuron signal information content. In this study, several auditory neuron responses and corresponding MNFR--generated surrogates are analyzed using mutual information (MI) as a metric of information content. Results showed that for particular inter-spike gaps (ISG), data MI exceeded two standard deviations of the surrogate MNFR MI, indicating spike spacing and order also encode information.

Investigation Of A Tractor-Tank Trailer Roadside Containment Barrier, Dean L. Whitfield

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to develop a new, cost-effective, Manual for Assessing Safety Hardware (MASH) Test Level 6 (TL-6) barrier. A literature review on prior Test Level 5 and Test Level 6 barriers was conducted, and the cost of current TL-5 and TL-6 barriers was established. Existing and modified design procedures for roadside barrier were reviewed as well as current TL-6 design forces. A preliminary TL-6 truck model was developed in LS-DYNA. The minimum barrier height to contain a tractor-tank vehicle was determined to be 62 in. for a rigid, vertical-faced barrier through LS-DYNA computer simulation. New …

Cyberinfrastructure For Intelligent Water Supply (Ciws) Data Visualization Challenge | College Of Engineering, Usu College Of Engineering

College of Engineering News

Associate Professor of Civil and Environmental Engineering Jeff Horsburgh is challenging Utah State University students to develop a visualization of high resolution water use data that provides visual feedback to both water providers and water consumers.

Usu Engineering Alumna Honored By Society Of Women Engineers | College Of Engineering, Usu College Of Engineering

College of Engineering News

Utah State University mechanical engineering alumna Amy Jo Moore was honored Oct. 20 at an annual conference for the Society of Women Engineers.

Increased Excitability Induced In The Primary Motor Cortex By Transcranial Ultrasound Stimulation, Benjamin C. Gibson, Joseph L. Sanguinetti, Bashar W. Badran, Alfred B. Yu, Evan P. Klein, Christopher C. Abbott, Jeffrey T. Hansberger, Vincent P. Clark

Publications and Research

Background: Transcranial Ultrasound Stimulation (tUS) is an emerging technique that uses ultrasonic waves to noninvasively modulate brain activity. As with other forms of non-invasive brain stimulation (NIBS), tUS may be useful for altering cortical excitability and neuroplasticity for a variety of research and clinical applications. The effects of tUS on cortical excitability are still unclear, and further complications arise from the wide parameter space offered by various types of devices, transducer arrangements, and stimulation protocols. Diagnostic ultrasound imaging devices are safe, commonly available systems that may be useful for tUS. However, the feasibility of modifying brain activity with diagnostic tUS …

High-Throughput Assessment Of A Novel, Thiol-Acrylate Hydrogel For Tumor Spheroid Synthesis In A Microfluidic Device, Nathan Daniel Kersker

LSU Master's Theses

The extracellular environment plays an important role in regulating cell behavior. The mechanical, structural, and compositional properties of the extracellular matrix can determine the fate of the growing cells. Standard two-dimensional culturing in a flask fails to represent a native cellular environment. To create the native environment suitable for cells, hydrogels were previously studied. One of the most extensively studied synthetic hydrogels was a poly(ethylene glycol diacrylate) (PEGDA) hydrogel. However, the need for UV polymerization may introduce unwanted changes in cell morphology and viability. The hydrogel being proposed was a form of a thiol-acrylate hydrogel that can eliminate this problem …

Transfer Learning With Deep Recurrent Neural Networks For Remaining Useful Life Estimation, Ansi Zhang, Honglei Wang, Shaobo Li, Yuxin Cui, Guanci Yang, Jianjun Hu

Faculty Publications

Prognostics, such as remaining useful life (RUL) prediction, is a crucial task in condition-based maintenance. A major challenge in data-driven prognostics is the difficulty of obtaining a sufficient number of samples of failure progression. However, for traditional machine learning methods and deep neural networks, enough training data is a prerequisite to train good prediction models. In this work, we proposed a transfer learning algorithm based on Bi-directional Long Short-Term Memory (BLSTM) recurrent neural networks for RUL estimation, in which the models can be first trained on different but related datasets and then fine-tuned by the target dataset. Extensive experimental results …

Webinar: Segmenting The Market For Transportation Demand Management Campaigns, Philip L. Winters, Amy Lester

TREC Webinar Series

Social marketing seeks to develop and integrate marketing concepts with other approaches to influence behaviors that benefit individuals and communities for the greater social good. It is a useful transportation demand management (TDM) planning approach to promote travel behavior change. The purpose of this study was to explore a consumer market segmentation technique successfully used in Europe for its applicability to marketing efforts in the United States. Attitudinal and demographic data were collected from 1900 individuals in Florida, Oregon, and Virginia modeled after the European approach. Clustering analysis was applied to divide the sample into segments so that members of …

Installation And Methodology For Determining Of Antifrictional Properties Of Antistatic-Heat-Conducting Composite Polymeric Materials Interacting With Fibrous Mass (Cotton-Raw), S.S. Negmatov, N.S. Abed, G. Gulyamov, O.H. Eshkabilov

Technical science and innovation

The paper Presents a disk tribometer installation and allows to determine the antifriction properties of machine-building composite antistatic-heat-conducting polymer materials working in interaction with the fibrous mass (raw cotton). A method for determining the friction force, temperature and electrostatic charge values arising in the friction zone is developed. The friction of the fibrous material is carried out on the flat surface of the rotating disk sample from the material under study at specified clamping pressures and sliding speeds. Values of friction forces, temperatures and values of electrostatic charges of the tested sample in a zone of friction with cotton-raw are …

Introduction To Data Analytics And Emerging Real-World Use Cases, Art Chaovalitwongse

Operations Management Presentations

Data analytics is a rapidly emerging interdisciplinary research area that involves advances in engineering, computer science, statistics and operations research. This webinar is focused on introducing the foundation of data analytics and emerging real-world use cases of data analytics. This presentation will begin with a discussion of the mathematical and statistical modeling aspects of various levels of data analytics (i.e., descriptive, predictive and prescriptive). In this webinar, you will hear an overview of data analytics in real world problems ranging from healthcare analytics, retail analytics and financial analytics.

Automatic Identification Of Animals In The Wild: A Comparative Study Between C-Capsule Networks And Deep Convolutional Neural Networks., Joel Kamdem Teto, Ying Xie

Master of Science in Computer Science Theses

The evolution of machine learning and computer vision in technology has driven a lot of

improvements and innovation into several domains. We see it being applied for credit decisions, insurance quotes, malware detection, fraud detection, email composition, and any other area having enough information to allow the machine to learn patterns. Over the years the number of sensors, cameras, and cognitive pieces of equipment placed in the wilderness has been growing exponentially. However, the resources (human) to leverage these data into something meaningful are not improving at the same rate. For instance, a team of scientist volunteers took 8.4 years, …

3-D Printable Polymer Pelletizer Chopper For Fused Granular Fabrication-Based Additive Manufacturing, Aubrey Woern, Joshua M. Pearce

Department of Materials Science and Engineering Publications

Although distributed additive manufacturing can provide high returns on investment, the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by three-dimensional (3-D) printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here allows for precisely controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built, and tested for its ability …

Highly Porous Ceramic Material And Method Of Using And Forming The Same, Alan W. Weimer, Xinhua Liang

Chemical and Biochemical Engineering Faculty Research & Creative Works

The present invention generally relates to porous ceramic material and to methods of making and using the material. More particularly, the invention relates to methods of forming ceramic materials by depositing material, using atomic layer deposition, onto a sacrificial substrate and to ceramic materials having controlled wall thickness, relatively large pores, and high surface area by weight.

An Electron‐Rich Calix[4]Arene‐Based Receptor With Unprecedented Binding Affinity For Nitric Oxide, Denan Wang, Lena V. Ivanova, Maxim V. Ivanov, Saber Mirzaei, Qadir K. Timerghazin, Scott A. Reid, Rajendra Rathore

Electrical and Computer Engineering Faculty Research and Publications

Calixarenes have found widespread application as building blocks for the design and synthesis of functional materials in host–guest chemistry. The ongoing desire to develop a detailed understanding of the nature of NO bonding to multichromophoric π‐stacked assemblies led us to develop an electron‐rich methoxy derivative of calix[4]arene (3), which we show exists as a single conformer in solution at ambient temperature. Here, we examine the redox properties of this derivative, generate its cation radical (3^+.) using robust chemical oxidants, and determine the relative efficacy of its NO binding in comparison with model calixarenes. We find …

Collaborative Product–Service Approach To Aviation Maintenance, Repair, And Overhaul. Part I: Quantitative Model, Cassio Dias Goncalves, Michael Kokkolaras

Journal of Aviation Technology and Engineering

This two-part paper proposes a new collaborative approach to airframe maintenance, repair, and overhaul (MRO). A quantitative model is introduced in Part I to represent the business relationships between original equipment manufacturers (OEMs) and MRO enterprises. In Part II, the presented model is used to assess potential financial benefits obtained by each of these stakeholders as a result of the collaboration.

The quantitative model is built to capture the main dependencies between an independent MRO enterprise operating in South America and its interactions with three major airframe OEMs. Interviews were conducted with MRO and OEM professionals to identify the most …