Engineering Commons^™

Epoxy Interlocking: A Novel Approach To Enhance Frp-To-Concrete Bond Behavior, Cheng Jiang, Baolin Wan, Yu-Fei Wu, John Omboko

Civil and Environmental Engineering Faculty Research and Publications

This paper presents a novel approach which can enhance the interfacial bond behavior between fiber reinforced polymer (FRP) composite material and concrete. Epoxy ribs are formed by grooving on the concrete surface before epoxy is applied. The dowel action from the epoxy ribs leads to an “epoxy interlocking” effect. The mechanism of the proposed epoxy interlocking approach was analyzed in this paper from both adhesion and interlocking aspects. Furthermore, the partial interaction of the epoxy interlocking was quantified and calibrated by experimental results. The epoxy interlocking in the tested specimens led to an 88.8% increase in bond strength on average. …

Impact Of Wide-Base Tires On Pavements: A National Study, Imad L. Al-Qadi, Jaime Hernandez, Angeli Gamez, Mojtaba Ziyadi, Osman Erman Gungor, Seunggu Kang

Civil and Environmental Engineering Faculty Research and Publications

This paper summarizes a multi-year effort comparing the new-generation wide-base tires (NG-WBT) and dual-tire assembly from a holistic point of view. The tires were compared considering not only pavement damage but also environmental impact. Numerical modeling, prediction methods, experimental measurements, and life-cycle assessment were combined to provide recommendations about the use of NG-WBT. A finite element (FE) approach considering variables that are usually omitted in the conventional analysis of flexible pavement was used for modeling pavement structures combining layer thickness, material properties, tire load, tire-inflation pressure, and pavement type (interstate and low volume). A prediction tool, ICT-Wide, was developed based …

Development Of Domain Analysis To Predict Multi-Axial Flexible Airfield Pavement Responses Due To Gear And Environmental Loadings, Angeli Gamez, Jaime Hernandez, Imad L. Al-Qadi

Civil and Environmental Engineering Faculty Research and Publications

Flexible pavement design procedures use maximum mechanistic strains to predict service life via empirical transfer functions. The conventional method of using predefined point locations for potential damage may not accurately represent realistic pavement scenarios. For instance, flexible airfield pavement analysis mainly considers the critical strain at the bottom of the asphalt concrete (AC), which may not characterize near-surface cracking potential. In lieu of point strains, domain analysis, a new method, accounts for the multi-axial behavior of pavements, as inherently excited by three-dimensional (3-D) and nonuniform aircraft tire–pavement contact stresses. Initially applied on highway pavements considering truck tire loading, this approach …

Development, Testing, Analysis, And Efficiency Of A Variable Area Dredge In Combination With A Mobile Ferrate-Based Treatment Facility, Leigh Ann Provost

Theses and Dissertations

This thesis proposal outlines the development and testing of a mobile slurry treatment trailer coupled with a variable area suction head and further expands on results and procedures shown in Feasibility of Muck Removal in the IRL Watershed and Subsequent Ferrate Treatment to Remove Excess Nutrients. The purpose of this thesis is to evaluate the efficiency and effectiveness of the suction head based on the percent solids maintained during dredging. This thesis also evaluates a scaled design and associated costs for a fully scaled dredging project utilizing the suction head. Additional statistics involving further fitting sediment data to a Weibull …

Multifunctional Coatings For Biodegradable Biomedical Devices, Sankalp Agarwal

Doctoral

Magnesium (Mg) and its alloys have been widely explored for orthopaedic applications due to its biodegradable nature, biocompatibility and closely related mechanical properties with bone. However, rapid degradation of Mg alloys under physiological conditions is a major challenge for biomedical industries and clinicians. Amongst the various methods employed, deposited coatings have been widely favoured to enhance the corrosion resistance and compatibility of the Mg alloys. This study focused on developing multifunctional coatings on AZ31 Mg alloy having a corrosion resistant, osteoinductive and antibacterial properties for orthopaedic applications. The aim of this study was achieved through the following objectives: - Fabrication …

Solar Irradiance Microforecasting, Austin Jeffrey Fite, Sara Naseem Kipps

Computer Engineering

In late winter quarter 2018 the University of New Mexico and Microgrid Labs provided the Cal Poly Electrical Engineering department with their prototype Solar Irradiance Microforecasting (SIMF) hardware. This hardware was provided to the University under the lone condition that data collected with it would be returned to Microgrid Labs to train their weather model. The goal of this senior project was to take the provided hardware and software and make it usable for students in the Cal Poly Electrical and Computer Engineering departments to hack and expand. The end goal with the hardware is near term cloud and weather …

Single Arm Recumbent Bicycle, Alexander Borsotti, Ryan Westermann, Sean Liston

Mechanical Engineering

The goal of this report is to outline and cover the scope of work for the Single Arm Recumbent Bicycle Senior Project. The report will give an introduction of the problem, a background of the existing research or products relating to our project, the objectives of our project, our project management plan, our final design, manufacturing, testing, our project management, and final recommendations for improving the final design. The team is being supported by the Quality of Life Program, a non-profit organization that works to improve the lives of those injured in duty while serving our nation.

Up until now, …

Implementing Coordination Lab And Lesson Into Cm 413 - Job Site, Connor R. Westover

Construction Management

Coordination can make or break a job. The act of coordination and the millions of pieces that go into a single project can directly affect both the schedule and budget of a construction project. Coordination is not a single part of the job, it is an on-going process that continuously involves all entities of the project. The importance of coordination and what it entails is not yet captured in the Cal Poly Construction Management curriculum. The purpose of this project would be to capture that importance and continue to build upon it to better prepare Cal Poly Builders for the …

Soil Health Effects And Stakeholder Perceptions Of Manure And Woody Biomass Application To Cropland In Nebraska, Linda R. Schott

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Organic products that have historically been viewed as waste products may improve soil health by adding carbon (C) and nutrients to soil. Two such products are woodchips, generated from forest or rangeland management activities, and livestock manure. In Nebraska, eastern redcedar (Juniperus virginiana L.) is a native but invasive tree species inhibiting rangeland productivity. Livestock manure that is underutilized while inorganic fertilizers are imported for crop production presents a water quality risk by contributing to local- and regional-scale nutrient imbalances. Increasing the responsible use of livestock manure in crop fertility programs to improve sustainability of both livestock and crop farms …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Lipid Extraction From Spirulina Sp. And Schizochytrium Sp. Using Supercritical Co2 With Methanol, Shihong Liu, Husam A. Abu Hajar, Guy Riefler, Ben J. Stuart

Civil & Environmental Engineering Faculty Publications

Microalgae are one of the most promising feedstocks for biodiesel production due to their high lipid content and easy farming. However, the extraction of lipids from microalgae is energy intensive and costly and involves the use of toxic organic solvents. Compared with organic solvent extraction, supercritical CO₂ (SCCO₂) has demonstrated advantages through lower toxicity and no solvent-liquid separation. Due to the nonpolar nature of SCCO_2, polar organic solvents such as methanol may need to be added as a modifier in order to increase the extraction ability of SCCO₂. In this paper, pilot scale lipid …

Generation Of 360 Degree Point Cloud For Characterization Of Morphological And Chemical Properties Of Maize And Sorghum, Suresh Thapa

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Recently, imaged-based high-throughput phenotyping methods have gained popularity in plant phenotyping. Imaging projects the 3D space into a 2D grid causing the loss of depth information and thus causes the retrieval of plant morphological traits challenging. In this study, LiDAR was used along with a turntable to generate a 360-degree point cloud of single plants. A LABVIEW program was developed to control and synchronize both the devices. A data processing pipeline was built to recover the digital surface models of the plants. The system was tested with maize and sorghum plants to derive the morphological properties including leaf area, leaf …

Variable Rate Irrigation Using A Spatial Evapotranspiration Model With Remote Sensing Imagery And Soil Water Content Measurements, Sandeep Bhatti

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Variable rate irrigation may help in intensification of agriculture by producing more yield per unit inputs. Real time spatial information about water balance components is important for designing VRI prescription maps. This work involved use of a spatial evapotranspiration model for studying spatial variability in an agricultural field at the Eastern Nebraska Research and Extension Center near Mead, Nebraska. Imagery from unmanned aerial systems and Landsat were used as input for the spatial evapotranspiration model. Other inputs into the model were soil water content measurements from neutron probes, weather data, crop data, previous irrigation prescriptions, and soil properties for the …

Photochemical Etching Of Nitrided Stainless Steel Piston Rings, Steven Sonntag

Mechanical Engineering Undergraduate Honors Theses

Piston rings are designed to provide a seal between the piston and the cylinder wall of internal combustion engines, keeping oil from the crankcase from getting into the combustion chamber. This means piston rings are the main point of contact between the piston and the cylinder wall, which causes the piston to experience high amounts of friction and wear. By texturing the surfaces of the cylinder wall and/or the piston ring, the amount of contact area can be reduced, allowing for less friction, slower wear, and better gas mileage. In this thesis experiments, photochemical etching processes were developed to etch …

Optimizing The Plasmonic Enhancement Of Light In Metallic Nanogap Structures For Surface-Enhanced Raman Spectroscopy, Stephen Joseph Bauman

Graduate Theses and Dissertations

Technology based on the interaction between light and matter has entered something of a renaissance over the past few decades due to improved control over the creation of nanoscale patterns. Tunable nanofabrication has benefitted optical sensing, by which light is used to detect the presence or quantity of various substances. Through methods such as Raman spectroscopy, the optical spectra of solid, liquid, or gaseous samples act as fingerprints which help identify a single type of molecule amongst a background of potentially many other chemicals. This technique therefore offers great benefit to applications such as biomedical sensors, airport security, industrial waste …

Cubesat Docking And Resource Sharing Mechanism, Shingo Kunito

Theses and Dissertations

This thesis addresses the design concept of a CubeSat docking and resource sharing mechanism that allows to transfer propellant that is pressurized gas, data, and power. In docking and capture design, the interface is equipped with two air cylinders that are rated up to 20.68 MPa internal pressure generating the ideal force of 1218.4 N each. With the designed air cylinder and mounted configuration, the maximum capture distance between the target and the chaser CubeSat is 40.30 mm. Since air cylinder and body frame are designed specifically for this interface, structural analysis was conducted in ANSYS where results show a …

An Analytical Model Of Material Deformation In Rotary Friction Welding Of Thin-Walled Tubes, Caleb James Brown

Theses and Dissertations

A new model of the material flow in rotary friction welding of tubes is proposed. The material flow proposed is based on 3D scans of welds performed with tungsten tracers. The tracers indicate a bifurcation of flow into two deformation paths. A different analysis is performed on each path.The material in Path 1 interacts with the weld interface and exhibits large amounts of azimuthal flow. Previous analytical investigations that have analytically modelled the weld interface as a non-Newtonian fluid are used to calculate the strain rate in this zone.The material in Path 2 transitions from axial to primarily radial flow. …

Engineering Cell-Free Biosystems For On-Site Production And Rapid Design Of Next-Generation Therapeutics, Kristen Michelle Wilding

Theses and Dissertations

While protein therapeutics are indispensable in the treatment of a variety of diseases, including cancer, rheumatoid arthritis, and diabetes, key limitations including short half-lives, high immunogenicity, protein instability, and centralized production complicate long-term use and on-demand production. Site-specific polymer conjugation provides a method for mitigating these challenges while minimizing negative impacts on protein activity. However, the location-dependent effects of polymer conjugation are not well understood. Cell-free protein synthesis provides direct access to the synthesis environment and rapid synthesis times, enabling rapid evaluation of multiple conjugation sites on a target protein. Here, work is presented towards developing cell-free protein synthesis as …

Conceptual Design Of A Pilot-Scale Pressurized Coal-Feed System, Taylor L. Schroedter

Theses and Dissertations

This thesis discusses the results and insights gained from developing a CFD model of a pilot-scale pressurized dry coal-feed system using the Barracuda CFD software and modeling various design concepts and operating conditions. The feed system was required to transport approximately 0.00378 kg/s (30 lb/hr) of pulverized coal from a vertical hopper to a 2.07 MPa (20.4 atm or 300 psi) reactor with a CO2-to-coal mass flow ratio of 1-2. Two feed system concepts were developed and tested for coal mass flow, CO2-to-coal mass ratio, steadiness, and uniformity. Piping system components also were evaluated for pressure drop and coal roping.With …

Large-Scale Testing Of Low-Strength Cellular Concrete For Skewed Bridge Abutments, Rebecca Eileen Black

Theses and Dissertations

Low-strength cellular concrete is a type of controlled low-strength material (CLSM) which is increasingly being used for various modern construction applications. Benefits of the material include its ease of placement due to the ability of cellular concrete to self-level and self-compact. It is also extremely lightweight compared to traditional concrete, enabling the concrete to be used in fill applications as a compacted soil would customarily be used. Testing of this material is not extensive, especially in the form of large-scale tests. Additionally, effects of skew on passive force resistance help to understand performance of a material when it is used …

Two-Phase Interactions On Superhydrophobic Surfaces, Kimberly Ann Stevens

Theses and Dissertations

Superhydrophobic surfaces have gained attention as a potential mechanism for increasing condensation heat transfer rates. Various aspects related to condensation heat transfer are explored. Adiabatic, air-water mixtures are used to explore the influence of hydrophobicity on two-phase flows and the hydrodynamics which might be present in flow condensation environments. Pressure drop measurements in a rectangular channel with one superhydrophobic wall (cross-section approximately 0.37 X 10 mm) are obtained, revealing a reduction in the pressure drop for two-phase flow compared to a control scenario. The observed reduction is approximately 10% greater than the reduction that is observed for single-phase flow (relative …

Repopulation And Stimulation Of Porcine Cardiac Extracellular Matrix To Create Engineered Heart Patches, Silvia Juliana Moncada Diaz

Theses and Dissertations

Heart failure is the main cause of death for both men and women in the United States. The only proven treatment for patients with heart failure is heart transplantation. The goal of this research is to create patches of tissue that could mimic the function of the native heart to repair the damaged portions of the heart. In this study, whole porcine hearts were decellularized to create a 3D construct that was recellularized with cardiomyocytes (CM) differentiated from human induced pluripotent stem (IPS) cells. At day 4 of differentiation, IPS-derived CMs were implanted onto cardiac extracellular matrix (cECM) and ten …

Characterization Of Pyrolysis Products From Fast Pyrolysis Of Live And Dead Vegetation, Mohammad Saeed Safdari

Theses and Dissertations

Wildland fire, which includes both planned (prescribed fire) and unplanned (wildfire) fires, is an important component of many ecosystems. Prescribed burning (controlled burning) is used as an effective tool in managing a variety of ecosystems in the United States to reduce accumulation of hazardous fuels, manage wildlife habitats, mimic natural fire occurrence, manage traditional native foods, and provide other ecological and societal benefits. During wildland fires, both live and dead (biomass) plants undergo a two-step thermal degradation process (pyrolysis and combustion) when exposed to high temperatures. Pyrolysis is the thermal decomposition of organic material, which does not require the presence …

Relationship Between Compressive Strength Of Different Shape And Thickness Specimens Of Type S Mortar, Theodore James Moffett

Theses and Dissertations

Mortar is the cementitious binding material placed between masonry blocks to create a composite system. The American Society of Testing and Materials (ASTM), along with other organizations, have established the testing of prismatic mortar specimens for evaluating mechanical properties, like compressive strength. Mortar joints, however, possess vastly different characteristics compared to prismatic specimens, especially in terms of geometry and water content. These differences prevent a direct comparison of compressive strength between prismatic specimens and actual mortar joints in the assembly. The objective of this study was to analyze Type S mortar joints, with particular emphasis on specimen shape and water …

Experimental Evaluation Of Replaceable Shear Fuse Moment Connections, Shannon Shun Oh

Theses and Dissertations

Steel special moment frames (SMFs) are known to be highly ductile seismic force- resisting systems. The performance of an SMF relies on the ability of the connections to accommodate large inelastic deformations. After the brittle failure of some steel moment frame connections during the 1994 Northridge Earthquake, experimental tests were used to investigate the ductility and strength of these connections. An experimental study was performed to investigate the seismic performance a new connection called the Replaceable Shear Fuse (RSF) connection. The RSF connection uses shear-yielding fuse plates to prevent beam and column yielding. A total of 7 test specimens with …

Internal Deformation Measurements And Optimization Of Synthetic Vocal Fold Models, Cassandra Jeanne Taylor

Theses and Dissertations

Developing lifelike vocal fold models is challenging due to various associatedbiomechanical complexities. Nevertheless, the development and analysis of improved vocal foldmodels is worthwhile since they are valuable tools for gaining insight into human vocal foldvibratory, aerodynamic, and acoustic response characteristics. This thesis seeks to contribute tothe development of computational and physical vocal fold modeling in two ways. First is byintroducing a method of obtaining internal deformation fields within vibrating synthetic vocal foldmodels; second is by presenting an optimization algorithm coupled with a computational vocalfold model to optimize geometry and stiffness of a synthetic vocal fold model to achieve morerealistic vibration …

The Effects Of Haptics On Rhythm Dance Game Performance And Enjoyment, Bridger Scott Hodges

Theses and Dissertations

Haptics are an exciting, ever-expanding field, particularly in relation to video games. Though haptics found their way rather quickly into conventional games through devices like handheld controllers, music and rhythm titles have hardly seen such attention. Little research has been done to examine the effects of haptics on rhythm dance games from a quantitative and qualitative standpoint for the player. StepMania is an open-source dance game which closely mimics the popular title Dance Dance Revolution. This research investigates the effects of haptics on a sample size of fifty individuals. Each completed three songs in the game with varying conditions: the …

Large-Scale Non-Linear Dynamic Optimization For Combining Applications Of Optimal Scheduling And Control, Logan Daniel Beal

Theses and Dissertations

Optimization has enabled automated applications in chemical manufacturing such as advanced control and scheduling. These applications have demonstrated enormous benefit over the last few decades and continue to be researched and refined. However, these applications have been developed separately with uncoordinated objectives. This dissertation investigates the unification of scheduling and control optimization schemes. The current practice is compared to early-concept, light integrations, and deeper integrations. This quantitative comparison of economic impacts encourages further investigation and tighter integration. A novel approach combines scheduling and control into a single application that can be used online. This approach implements the discrete-time paradigm from …

Origami-Based Design Of Fold States And Stability, Alex Avila

Theses and Dissertations

Origami is a potentially elegant and powerful source of inspiration for many engineering designs. The viable shapes (fold states) of a single device allow it to perform multiple, seemingly contradictory, functions. The fold state is a large factor in the device's performance, but there are challenges in selecting and maintaining those fold states. In this thesis we analyze existing concepts for overcoming these challenges. Those concepts are compared with those that occur in origami-based devices. From this analysis fundamental gaps were identified, specifically, shortcoming in the terminology used to refer to (1) non-flat origami states and (2) sets of facets …

Examining The Mechanics Responsible For Strain Delocalization In Metallic Glass Matrix Composites, Casey Owen Messick

Theses and Dissertations

Metallic glass matrix composites (MGMCs) have been developed to improve upon the ductility of monolithic metallic glass. These composites utilize a secondary crystalline phase that is grown into an amorphous matrix as isolated dendritic trees. This work seeks to understand the mechanisms underlying strain delocalization in MGMCs in order to better direct efforts for continual progress in this class of material. A mesoscale modelling technique based on shear transformation zone (STZ) dynamics is used to do so. STZ dynamics is a coarse grained technique that can provide insight into the microscopic processes that control macroscopic behavior, but which can be …