Engineering Commons^™

Project "Auxilia" - Jaiden's Prosthetic Arm, Christopher Halley, Lindsay Jaros, Autumn Young

Williams Honors College, Honors Research Projects

The main objective of this project was to create a prosthetic arm for a 15 year old boy named Jaiden Foden. Jaiden was born with only one fully developed limb as a result of a genetic disorder, Hanhart Syndrome II. His right arm becomes a residual limb below the elbow, but has two fingers which act in a “claw-like” movement. Jaiden’s left arm becomes a residual limb above the elbow, and his left leg becomes a residual limb above the knee. The goal of the arm was to increase Jaiden’s overall independence and to help in completing daily tasks, such …

Reactive Archey Target Design Team "Mimic", Brandon Croyle, Jacob Boss, David Rodgers, Austin Wivell

Williams Honors College, Honors Research Projects

This design project will aim to provide archery hunters with a platform to simulate shooting at string jumping deer. String jumping refers to a spooked deer hearing the snap of a bow string and instintivly ducking up to ten inches. This often results in wounded or missed deer. We will design and build a control system that uses the sound of a bow string as a trigger to operate a mechanical target system. A sound sensor will mimic a deer’s hearing in close range hunting and then send a signal to the mechanical system to replicate the dropping motion of …

Increasing Mechanical Properties Of A Double Network Hydrogel From Polyacrylamide And Agar With Methylenebisacrylamide As A Photocrosslinker, Madelyn Jeske

Williams Honors College, Honors Research Projects

Double Network hydrogels are three dimensional networks of a soft, mechanically tough material that have been used for drug delivery, agriculture, adhesives, and other widely applicable uses. Using the one-pot method, a single hydrogel can be produced in 3 hours as opposed to the once demonstrated three days. It has been found that with a first, physically cross linked network and a second, chemically cross linked, hybrid double network hydrogels exhibit high mechanical properties and are freeshapeable. Agar is a thermoreversible organic molecule with a triple helix structure that provides an excellent first network that organizes into aggregate bundles once …

Anti-Roll Bar For Sae Baja Vehicle, Jennifer Bulgrin, Zachary A. Gnabah, Scott P. Toth

Williams Honors College, Honors Research Projects

This report explores the need to improve the Zips Baja vehicle handling performance. This will be achieved by designing an anti-roll bar system for the rear suspension of the Zips Baja vehicle to decrease the turning radius of the vehicle. The project develops specific goals to achieve increased performance, goes through the engineering design cycle to create a prototype, evaluate its effectiveness, optimize the design through several iterations, and design a final solution. After sub-functions have been determined, conceptual ideas for completing all sub-functions were evaluated and a conceptual design was selected to proceed into the embodiment design phase. Once …

Benefits Of Aluminum: Comparing The Common Materials In The Bar Grating Industry, Joanthan Geiser

Williams Honors College, Honors Research Projects

The main aim of this project is to study the wholistic behavior of the 6xxx series of aluminum for use in the bar grating industry for a waste water treatment environment. This project will study the comparison of certain aluminum 6xxx series alloys to steel, stainless steel, and glass fiber-reinforced plastic. While comparing these materials, it will look at the mechanical properties such as modulus of elasticity, yield strength, and ultimate tensile strength. In addition, the available corrosion test of the 6xxx series aluminum alloys will be examined to find a generalization of the corrosion behavior for this series. A …

Center Lift Trailer Support Structure, Carson Corle, Anthony M. Hayes, Bryan A. Truax

Williams Honors College, Honors Research Projects

Center lift pontoon trailers have a high center of gravity, therefore have the potential for the pontoon and trailer to tip while cornering. There is need for a component to stabilize the pontoon on the trailer while towing. Different concepts of a support system were sketched to determine the best option. The characteristics that were deemed important for the support system were narrowed down to determine the best concept and the connections of the best design were sketched in greater detail. The forces that the support system would have to withstand to stabilize the pontoon on the trailer were calculated. …

Fluidized Bed Classroom Demonstration Unit, Theresa Chapa

Williams Honors College, Honors Research Projects

Fluid and Thermal Operations is a 4th year chemical engineering course at the University of Akron designed to introduce undergraduate students to the engineering and mathematical concepts behind the operation of a fluidized bed. The purpose of this honors project is to design and manufacture an inexpensive and portable unit that can be used in the classroom to visually demonstrate three functions of a fluidized bed to students. The fluidized bed is manufactured from items that can be purchased from a department or hardware store, is capable of being transported by a single person to and from a classroom and …

Automatic Range Finding Bow Sight, Garrett Gill, Dillon Denny, Cory Verba

Williams Honors College, Honors Research Projects

With the growing popularity of archery, a system designed to help an archer achieve the best shot possible becomes necessary. The Automatic Range Finding Bow Sight is a system that consists of a single pin sight controlled by a servo motor. The servo motor controls the sight pin by rotating a drive wheel that will move the pin up or down. The sight pin movement is based on a reading obtained by a built-in rangefinder and speed data input by the user. This data will then be compared to programmed lookup tables in order to find the appropriate pin position. …

Investigating Alternative Measures Of Functional Recovery In Rat Sciatic Nerve Injury, Mariah L. Costa, Rebecca K. Willits

Williams Honors College, Honors Research Projects

There is a pressing need for advancements in peripheral nerve repair techniques and functional recovery evaluation methods. The rat sciatic nerve injury model is a well examined model for peripheral nerve repair. One measure of functional recovery after nerve damage, the sciatic functional index (SFI), fails in the presence of self-mutilation, toe contracture, and other abnormalities in gait. In this IACUC approved study, the sciatic nerve was severed in four experimental groups (n=5). The nerves were repaired with Arginylglycylaspartic acid-poly(ε-caprolactone) (RGD-PCL) peptide functionalized nanofibers, non-functionalized PCL control nanofibers, an isograft, and a negative control empty conduit. Video walking track analysis …

Optimization Of Conditions For Production Of Mechanically Strong Suckerin Protein Hydrogels, Autumn Furniss

Williams Honors College, Honors Research Projects

Hydrogels are polymer networks with a large water content. Uses include biomedical applications like drug delivery, wound dressing, and more. Current natural hydrogels lack mechanical robustness. Squid ringed teeth (completely protein) have a modulus comparable to thermoplastics; adding this to hydrogels could improve modulus while maintaining biocompatibility.

Three experiments were performed: Hofmeister solubility study, SRT powder additive, and SRT aqueous solution. The first showed that LiCl solution without acetic acid dissolved the most SRT; overall LiCl dissolved more than all others. SRT as a powder additive increased the modulus of the hydrogels, however the error in the measurements make it …

The Wrist Brace Project, Nathan Nicholas

Williams Honors College, Honors Research Projects

This paper outlines the engineering design process of creating a specialized wrist brace for a local child. This project was completed by a team of senior Biomedical Engineering students.

Fabrication And Characterization Of Nanofiber Nylon-6-Mwcnt As An Electrochemical Sensor For Sodium Ions Concentration Detection In Sweat, Kelsey Mills

Williams Honors College, Honors Research Projects

Fabrication and characterization nylon-6-MWCNT nanofiber as an electrochemical sensor to detect sodium ion concentrations specifically in sweat. Using contact angle to determine surface morphology and chronoamperometry testing to identify ideal sensor conditions, tests optimized parameters like weight percent of nylon or other polymers, carbon nanotube (CNT) isomer, and solution concentration to determine reproducibility of functional sensors. Utilizing the electric qualities of carbon nanotubes partnered with the sodium ion selectivity of calixarene treatment and polymers unique properties like flexibility and scalability create open an arena for optimizing sodium ion sensors for further development for functional prototypes. Morphology tests showed that the …

Synthesis Of Drug Encapsulated Chitosan-Heparin Based Nanoparticles And Release Study, Trent Richwine

Williams Honors College, Honors Research Projects

The main objective of this honor’s project is to encapsulate drugs with different molecular weights inside of chitosan-heparin based nanoparticles (Cs-Hep NPs). Three different drugs with low (NNC), medium (IFN-γ), and large (BSA) molecular weights were chosen in order to compare all types of drugs and how they react with the nanoparticles. Analysis of particle size, zeta potential, and a release study was performed. The release took place over a 168-hour time period and liquid samples were taken throughout. The hypothesis was that the molecular weight of the drug will correlate to the physical properties of the nanoparticles. The results …

Simulation Of Lubricant For Design Of Magnetic Recording Systems Under Laser Heating, Ryan Hetzel, Shao Wang Dr., Jonathon Lawry, Ahmed Alsafwani

Williams Honors College, Honors Research Projects

Heat assisted magnetic recording is an advanced technology which can enable storage density increase in next generation hard disk drive. These drives are implemental in server (cloud) storage and the storage of large projects such as the Event Horizon Telescope which recently captured images of a black hole. The data is written on the magnetic surface by means of laser heating. The coercivity of magnetic medium is reduced by heating surface and within heating period data is written on disk. During the heating process, lubricant present on the disk might evaporate because of high temperature of laser and can accumulate …

Artificial Intelligence In Wet Weather Infrastructure, Matt Hammerstein

Williams Honors College, Honors Research Projects

Effective management of runoff from rain and snowmelt is critical as increased water flows can negatively affect efficiency and reliability at treatment facilities, as well as potentially damage property or the natural environment. Implementation of artificial intelligence for real-time decision making and support in wet weather infrastructure is a recent technological development; as such, a problem has emerged: experience and knowledge of best practices for successful implementation is limited. Artificial intelligence is being employed to inform operational decisions that are intended to improve the efficiency and reliability of physical wet weather infrastructure. The goal of municipalities and utilities in utilizing …

Incorporation Of Contaminated Sediment Into Environmentally Safe Concrete, Andrew Needs

Williams Honors College, Honors Research Projects

The research performed through this project provided some interesting results on how the different properties of the contaminated sediment can impact the strength of the new concrete.

Average three, seven, and fourteen-day strengths increased when comparing to the baseline mix developed for the experiment. Increases in strengths were notices in the ten and twenty-five percent soil replacement mixes. The largest increase was approximately thirty-three percent greater than the baseline average.

The results from the forty percent replacement test showed a significant decrease in strengths when comparing against the baseline mix. A loss of about thirty percent was observed between the …

Development Of Cardanol-Based Epoxy Coating, Nicholas Pottschmidt

Williams Honors College, Honors Research Projects

The purpose of this project was to determine the suitability of cardanol glycidyl ether (CGE) as a substitute for trimethylolpropane triglycidyl ether (TMPGE) as the reactive diluent in epoxy coatings. CGE may be a naturally-derived alternative to TMPGE, which is a commonly-used petroleum-derived reactive diluent. Epoxy coatings were formulated with CGE replacing increasing amounts of TMPGE in the formulation. Corrosion protection provided by the coatings was evaluated with electrochemical impedance spectroscopy (EIS). Mechanical properties of the coatings (hardness, flexibility, adhesion, and impact resistance) were evaluated with applicable ASTM standards.

EIS results revealed the coating formulated with only CGE had superior …

Design And Mechanical Characterization Of 3d Printed Gradient Porosity Poly(Propylene Fumarate) Scaffolds, Andrea Felicelli

Williams Honors College, Honors Research Projects

Worldwide incidence of bone disorders and conditions, an already prevalent problem, is expected to double by 2020 from the rate in 2013 due to factors such as higher life expectancies and lower levels of physical activity. Every year in the United States, over half a million patients receive bone defect repairs, with costs greater than $2.5 billion. Current repairs are typically done with bone grafts, which are often costly and can result in added complications in the donor surgical site. Tissue engineering, a growing field that seeks to assist and enhance tissue defect repairs through the use of synthetic materials, …

Fluid Power Vehicle Competition, Madison Graham, Wayne Ritchie, Emily Dicks, Ariana Cupello

Williams Honors College, Honors Research Projects

Our senior design project for the Honors College and the Department of Mechanical Engineering was to design a fluid powered vehicle. Our design was tested in an official capacity against other universities’ vehicles at the Fluid Powered Vehicle Challenge hosted and funded by the National Fluid Power Association (NFPA) and its industry partners. This competition had six different evaluations for our vehicle design; three race events, midway presentation, final presentation, and safety inspection. The three different race events were the sprint race, the efficiency race, and the endurance race. The sprint race was a 475 feet speed test, the efficiency …

Carbon Fiber Racing Wheel, Megan Sanok, Melissa Furdak, Sydney Schipani

Williams Honors College, Honors Research Projects

Industry today thrives off of competition; everybody wants their product to be the best. Across almost every field of manufacturing and design, there is a pattern of factors that companies strive for when producing their specialized products. The most effective companies can create a commodity that is relatively inexpensive, easy to manufacture, and has the ability to meet high standards. As engineers, it is ingrained in us that there is always room for improvement, and that we have been given the tools to make it happen.

When evaluating what needed to be improved in our daily lives, the SAE Zips …

Smart Parking Deck, Ryne Turner, Matthew Mcdade, Julie Aichinger, Laveréna Wienclaw

Williams Honors College, Honors Research Projects

The Smart Parking Deck employs elementary circuit design elements and mobile application development. Each device module uses laser proximity sensors to check the availability of an individual parking space and a Zigbee unit to communicate with the adjacent device module. The modules are connected to a network hub that manages all of the incoming and outgoing parking data. This data is displayed on the mobile application. The system is easily manageable and energy efficient, significantly decreasing the costs associated with other smart parking systems on the market. This system is aimed at decreasing commute time for students by allowing them …

Synthesis Of Polyurethane From Sustainable Sources, Jovan Jevric

Williams Honors College, Honors Research Projects

The most common method of polyurethanes involves a reaction between various petroleum-based isocyanates and a polyol along with a catalyst; all of which have a negative impact on environmental and human health. The objective of this research project is to eliminate or mitigate the risks and hazards associated with the production and degradation of polyurethane. Hexamethylene diisocyanate isocyanurates (3HDI) are one of the most common isocyanates used in the polyurethane processing industry. 3HDI contains numerous toxins, and it has a negative impact on the environment and human health¹. It has been found that there are other compounds that …

Baja Rack And Pinion, Devin Jackson

Williams Honors College, Honors Research Projects

Our senior design team chose to team up with The University of Akron’s SAE Zips Baja Team. The Zips Baja Team races off-road vehicles that they build every year. The team is trying to optimize and improve several sub categories for the 2019 car such as steering, drivetrain and suspension. Our design team met with a couple of the captains on the Zips Baja Team and were given a few choices of what sub category we could focus on for our project. We decided to take on the task of improving the vehicle steering rack and pinion gear system. The …

Chronoamperometry Analysis Of Sweat Sensor Technology, Evan Fritz

Williams Honors College, Honors Research Projects

Due to the demand for in-situ electrolyte sodium sensors, prototype sensors have been produced to create a product for athletes and marathoners to monitor hydration levels. These senors address a desire in the marketplace for athletic monitoring for overall athlete wellness and performance. Sweat sensor samples were created using Multi-walled Carbon Nanotubes functionalized on a Nylon-6 fiber mat using cyclo-oligomeric Calixarene. This production process produces sensors capable of detecting sodium ion concentration present in human sweat in presence of an electric current. Chronoamperometry analysis is used in this manner to determine the functionality of the sensors. Much of the research …

Rocket Telemetry System, Monica Lacek, Clark Bryant Iii, David Dalvin, Nicholas Wolgamott

Williams Honors College, Honors Research Projects

The goal of this research project is to design a system for the Akronauts Rocket Design Team which will transmit flight data in real-time to a ground station. The data will be collected from various sensors (altitude, acceleration, GPS, etc). This data will be transmitted wirelessly and in real-time to a receiving station. Calculations and visualizations will be taken from the data, which will help the team improve their rocket designs. Additionally, GPS data will be useful to locate the rocket post-flight. Challenges will include the need for the system to transmit over the range of the rocket’s flight and …

Motorcycle Eyes, Patrick Nie, Alexander Ray

Williams Honors College, Honors Research Projects

As technology continues to advance the safety factor has increased for vehicles on the roads. However, not much has been done to help improve the safety of motorcyclist. To help to solve this problem a wireless blind spot indicator for a motorcycle helmet will be designed. It will be powered off the motorcycle and have indication zones for the left, right, and rear blind spots. The system will alert the rider if a vehicle is within 7 meters of the back of the motorcycle in any of the mentioned blind spots. The radar sensors will detect the vehicle and send …

Pick-And-Place Robot For The 2019 Asme Student Design Competition, Riniah A. Foor, Megan Schmit, Aaron Urban, Jeanetta Davidsaver, Daniel Mugongo

Williams Honors College, Honors Research Projects

This project was undertaken as an opportunity to participate in a holistic experience of designing, building, and competing as an engineering design team. In the ASME Student Design Competition, undergraduate students are able to experientially learn the process of design inception, manufacture, and product performance in addition to the development of critical project management skills. This is done through a creative design challenge to build a device capable of accomplishing a “pick-and-place” task in a fast and efficient manner.

The Production And Characterization Of Chitosan Based Microgels Using A Novel Microfluidic Device To Promote Cell Survival, Kaileen Shevchuk

Williams Honors College, Honors Research Projects

The purpose of this project is to synthesize and characterize perfluorocarbon modified methacrylamide chitosan (MACF) microgels produced with the use of a capillary-based microfluidic device. Since cell survival and development is highly related to particles physical properties, analysis of microgels set out to determine the particle’s physical properties. I hypothesize that the viscosity of the MACF polymer as well as the amount of photo initiator influence the physical properties of synthesized particles and as a result can generate particles with various features for cell culture in terms of shape, size, charge and swelling abilities. This hypothesis was validated through the …

Controlled Release Of Corrosion Inhibitors: Zinc And Magnesium Containing Sodium Chromate, Andrew Thomas

Williams Honors College, Honors Research Projects

Corrosion can be combated by multiple methods, where the primary purpose is to minimize degradation of metal surfaces. Corrosion inhibitors are one of the most effective methods of corrosion protection. Inhibitors are substances that minimize corrosion in aggressive environments, with only a low concentration required. The inhibitors are chemically adsorbed on the surface of the metal and a protective thin film is formed . The mechanism of the inhibitors could be described as anodic, cathodic, or a mix of the two. Anodic inhibitors, also known as passivation inhibitors, alter an anode reaction. Corrosion potential of the metal is shifted to …

Laser Ablation Of Aluminum, Erika Nosal, Zachary Rahe, Arthur Pamboukis

Williams Honors College, Honors Research Projects

The laser ablation of metal carries relevance in a variety of engineering industries. This includes, but is not limited to, processes such as micromachining, or implementation on aircraft weaponry. The latter application is the reasoning for why aluminum is the specific metal in consideration, as it is commonly used for the construction of aircraft components.

The scope of this project was to optimize the energy dispersed through laser ablation on aluminum by mathematical modeling. The transient conduction process in the aluminum was modeled using a 2-dimensional cylindrical coordinate system in both MATLAB and ANSYS/Fluent. These models were adopted to simulate …