Engineering Commons^™

Influence Of Water Injection Rate On The Vortecone, An Impingement Screen, And A Conventional Filter Screen Cleaning Efficiency, Oscar Velasquez

Theses and Dissertations--Mining Engineering

Industrial produced respirable particles are known to affect the respirable tract of workers causing serious illness or even death. These particles can be found in any mining operation’s environment, new regulations by the Mine Safety and Health Administration (MSHA) in 2014 reduced the allowable limit of dust exposure for underground workers. Dust control practices have been improving over the years to lower the number of incidents caused by these particles. In underground mining, water sprays and scrubber systems have become the most used dust control methods. Water sprays create numerous fine water droplets to capture dust once it has become …

Quantification Of Myocardial Mechanics In Left Ventricles Under Inotropic Stimulation And In Healthy Right Ventricles Using 3d Dense Cmr, Zhan-Qiu Liu

Theses and Dissertations--Mechanical and Aerospace Engineering

Statistical data from clinical studies indicate that the death rate caused by heart disease has decreased due to an increased use of evidence-based medical therapies. This includes the use of magnetic resonance imaging (MRI), which is one of the most common non-invasive approaches in evidence-based health care research. In the current work, I present 3D Lagrangian strains and torsion in the left ventricle of healthy and isoproterenol-stimulated rats, which were investigated using Displacement ENcoding with Stimulated Echoes (DENSE) cardiac magnetic resonance (CMR) imaging. With the implementation of the 12-segment model, a detailed profile of regional cardiac mechanics was reconstructed for …

Development Of A Muffler Insertion Loss Flow Rig, Jonathan Chen

Theses and Dissertations--Mechanical and Aerospace Engineering

Mufflers and silencers are commonly used to attenuate noise sources such as internal combustion engines and HVAC systems. Typically, these environments contain mean flow that can affect the acoustic properties of the muffler components and may produce flow generated noise. To characterize the muffler performance, common metrics such as insertion and transmission loss and noise reduction are used in industry. Though transmission loss without flow is often measured and is a relatively simple bench top experiment and useful for model validation purposes, mean flow can significantly affect the muffler performance. There are a few existing and commercial transmission loss rigs …

Determination Of Acoustic Radiation Efficiency Via Particle Velocity Sensor With Applications, Steven Conner Campbell

Theses and Dissertations--Mechanical and Aerospace Engineering

Acoustic radiation efficiency is defined as the ratio of sound power radiated to the surface vibration power of a piston with equivalent surface area. It has been shown that the radiation efficiency is maximized and may exceed unity when the structural and acoustic wavelengths are approximately equal. The frequency at which this occurs is called the critical frequency and can be shifted with structural modifications. This has proven to be an effective way to reduce noise. The standard radiation efficiency measurement is comprised of an intensity scan for sound power measurement and accelerometer array for spatially averaged vibration determination. This …

Enhanced Surface Integrity With Thermally Stable Residual Stress Fields And Nanostructures In Cryogenic Processing Of Titanium Alloy Ti-6al-4v, James R. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

Burnishing is a chipless finishing process used to improve surface integrity by severe plastic deformation (SPD) of surface asperities. As surface integrity in large measure defines the functional performance and fatigue life of aerospace alloys, burnishing is thus a means of increasing the fatigue life of critical components, such as turbine and compressor blades in gas turbine engines. Therefore, the primary objective of this dissertation is to characterize the burnishing-induced surface integrity of Ti-6Al-4V alloy in terms of the implemented processing parameters. As the impact of cooling mechanisms on surface integrity from SPD processing is largely unexplored, a particular emphasis …

Transforming A Circular Economy Into A Helical Economy For Advancing Sustainable Manufacturing, Ryan T. Bradley

Theses and Dissertations--Mechanical and Aerospace Engineering

The U.N. projects the world population to reach nearly 10 billion people by 2050, which will cause demand for manufactured goods to reach unforeseen levels. In order for us to produce the goods to support an equitable future, the methods in which we manufacture those goods must radically change. The emerging Circular Economy (CE) concept for production systems has promised to drastically increase economic/business value by significantly reducing the world’s resource consumption and negative environmental impacts. However, CE is inherently limited because of its emphasis on recycling and reuse of materials. CE does not address the holistic changes needed across …

Quantification Of Papillary Muscle Motion And Mitral Regurgitation After Myocardial Infarction, Connor R. Ferguson

Theses and Dissertations--Mechanical and Aerospace Engineering

Change in papillary muscle motion as a result of left ventricular (LV) remodeling after posterolateral myocardial infarction is thought to contribute to ischemic mitral regurgitation. A finite element (FE) model of the LV was created from magnetic resonance images acquired immediately before myocardial infarction and 8 weeks later in a cohort of 12 sheep. Severity of mitral regurgitation was rated by two-dimensional echocardiography and regurgitant volume was estimated using MRI. Of the cohort, 6 animals (DC) received hydrogel injection therapy shown to limit ventricular remodeling after myocardial infarction while the control group (MI) received a similar pattern of saline injections. …

A Computational Study Of Patch Implantation And Mitral Valve Mechanics, Dara Singh

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarction (i.e., a heart attack) is the most common heart disease in the United States. Mitral valve regurgitation, or the backflow of blood into the atrium from the left ventricle, is one of the complications associated with myocardial infarction. In this dissertation, a validated model of a sheep heart that has suffered myocardial infarction has been employed to study mitral valve regurgitation. The model was rebuilt with the knowledge of geometrical changes captured with MRI technique and is assigned with anisotropic, inhomogeneous, nearly incompressible and highly non-linear material properties. Patch augmentation was performed on its anterior leaflet, using a …

Hot-Wire Anemometer Measurements Of Atmospheric Surface Layer Turbulence Via Unmanned Aerial Vehicle, Caleb A. Canter

Theses and Dissertations--Mechanical and Aerospace Engineering

An instrumented unmanned aerial vehicle (UAV) was developed and employed to observe the full range of turbulent motions that exist within the inertial subrange of atmospheric surface layer turbulence. The UAV was host to a suite of pressure, temperature, humidity, and wind sensors which provide the necessary data to calculate the variety of turbulent statistics that characterize the flow. Flight experiments were performed with this aircraft, consisting of a large square pattern at an altitude of 100 m above ground level. In order to capture the largest turbulent scales it was necessary to maximize the size of the square pattern. …

Indoor-Wireless Location Techniques And Algorithms Utilizing Uhf Rfid And Ble Technologies, Ann M. Whitney

Theses and Dissertations--Mechanical and Aerospace Engineering

The work presented herein explores the ability of Ultra High Frequency Radio Frequency (UHF RF) devices, specifically (Radio Frequency Identification) RFID passive tags and Bluetooth Low Energy (BLE) to be used as tools to locate items of interest inside a building. Localization Systems based on these technologies are commercially available, but have failed to be widely adopted due to significant drawbacks in the accuracy and reliability of state of the art systems. It is the goal of this work to address that issue by identifying and potentially improving upon localization algorithms.

The work presented here breaks the process of localization …

Trade-Off Balancing For Stable And Sustainable Operating Room Scheduling, Amin Abedini

Theses and Dissertations--Mechanical and Aerospace Engineering

The implementation of the mandatory alternative payment model (APM) guarantees savings for Medicare regardless of participant hospitals ability for reducing spending that shifts the cost minimization burden from insurers onto the hospital administrators. Surgical interventions account for more than 30% and 40% of hospitals total cost and total revenue, respectively, with a cost structure consisting of nearly 56% direct cost, thus, large cost reduction is possible through efficient operation management. However, optimizing operating rooms (ORs) schedules is extraordinarily challenging due to the complexities involved in the process. We present new algorithms and managerial guidelines to address the problem of OR …

Analysis Of Surface Integrity In Machining Of Cfrp Under Different Cooling Conditions, Arjun Nagaraj

Theses and Dissertations--Mechanical and Aerospace Engineering

Carbon Fiber Reinforced Polymers (CFRP) are a class of advanced materials widely used in versatile applications including aerospace and automotive industries due to their exceptional physical and mechanical properties. Owing to the heterogenous nature of the composites, it is often a challenging task to machine them unlike metals. Drilling in particular, the most commonly used process for component assembly is critical especially in the aerospace sector which demands parts of highest quality and surface integrity.

Conventionally, all composites are machined under dry conditions. While there are drawbacks related to dry drilling, for example, poor surface roughness, there is a need …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical and Aerospace Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

The Effects Of System Characteristics, Reference Command, And Command-Following Objectives On Human-In-The-Loop Control Behavior, Seyyedalireza Seyyedmousavi

Theses and Dissertations--Mechanical and Aerospace Engineering

Humans learn to interact with many complex physical systems. For example, humans learn to fly aircraft, operate drones, and drive automobiles. We present results from human-in-the-loop (HITL) experiments, where human subjects interact with dynamic systems while performing command-following tasks multiple times over a one-week period. We use a new subsystem identification (SSID) algorithm to estimate the control strategies (feedforward, feedforward delay, feedback, and feedback delay) that human subjects use during their trials. We use experimental and SSID results to examine the effects of system characteristics (e.g., system zeros, relative degree, system order, phase lag, time delay), reference command, and command-following …

Circulation Dependence Of The Interaction Between A Wing-Tip Vortex And Turbulence, Farshid Najarzadegan

Theses and Dissertations--Mechanical and Aerospace Engineering

Vortices are present in many fluid flows and depending on the context they may be either beneficial or harmful for different systems or processes. Planar particle image velocimetry was used to examine the vortex evolution and its decay under different turbulence intensities and vortex circulation. The vortex decayed faster in the presence of high turbulence intensity. Vortex trajectories were impacted by turbulence intensity and vortex strength. Trajectories with no turbulence intensity had less variation. The vortex wandering amplitude decreased with growth of vortex strength. The vortex decay was confined to the core of the vortex, with the tangential velocity at …

Single-Degree-Of-Freedom Experiments Demonstrating Electromagnetic Formation Flying For Small Satellite Swarms Using Piecewise-Sinusoidal Controls, Ajin Sunny

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis presents a decentralized electromagnetic formation flying (EMFF) control method using frequency-multiplexed sinusoidal control signals. We demonstrate the EMFF control approach in open-loop and closed-loop control experiments using a single-degree-of-freedom testbed with an electromagnetic actuation system (EAS). The EAS sense the relative position and velocity between satellites and implement a frequency-multiplexed sinusoidal control signal. We use a laser-rangefinder device to capture the relative position and an ARM-based microcontroller to implement the closed-loop control algorithm. We custom-design and build the EAS that implements the formation control in one dimension. The experimental results in this thesis demonstrate the feasibility of the …

Design Process For The Containment And Manipulation Of Liquids In Microgravity, Chris Meek

Theses and Dissertations--Mechanical and Aerospace Engineering

In order to enhance accessibility to microgravity research, the design process for experiments on the ISS must be streamlined and accessible to all scientific disciplines, not just aerospace engineers. Thus, a general design and analysis toolbox with accompanying best practices manual for microgravity liquid containment is proposed. The work presented in this thesis improves the design process by introducing a modular liquid tank design which can be filled, drained, or act as a passive liquid-gas separation device. It can also be pressurized, and used for aerosol spray. This tank can be modified to meet the design requirements of various experimental …

News - Screven-Jenkins Regional Library, Sharon Blank

Georgia Library Quarterly

No abstract provided.

Asphalt And Adhesive Flow And Level Control, Kajan V. Moorthy

Electrical Engineering

This project entails the design of a flow control system to manage flow rates of asphalt to maintain constant thickness on the fiberglass sheet. By using the proposed system, the amount of scrap created by extremely thick or thin deposits on the mat would be reduced. The design of the proposed system aims to produce a flowrate of 10 gpm while it is also capable of self-correcting and shutting down when unsafe conditions occur. Selection of various components of the control system took place which included the Allen Bradley PLC and Flex I/O, power supply, radars for level sensor, and …

Investigation Of The Effect Of Vehicle Color On Safety, Deogratias Eustace, Fayez Khalaf Alanazi, Peter W. Hovey

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

No abstract provided.

A Learning-Centered Paradigm For Engineering Graphics And Design: Engineering Technology Students' Skill Gains And Capstone Preparation, Rustin Webster

School of Engineering Technology Faculty Publications

This descriptive non-experimental follow-on study investigates the extent to which a learning-centered paradigm in an engineering graphics and design course prepared undergraduate engineering technology (ET) students for senior capstone and how the course impacted vital professional and technical skills. A small 2016 case study (n = 10) showed that the course, which was approximately 5% passive and 95% active learning produced positive skill gains for ET students (Webster 2017). However, this follow-on study was needed largely from the inability of the 2016 case study to 1) identify and/or confirm data trends and 2) fully gauge the students’ preparation for senior …

Reconfigurable Reflectarray Antennas With Bandwidth Enhancement For High Gain, Beam-Steering Applications, Michael Trampler

Electronic Theses and Dissertations

Reconfigurable reflectarrays are a class of antennas that combine the advantages of traditional parabolic antennas and phased array antennas. Chapter 1 discusses the basic operational theory of reflectarrays and their design. A review of previous research and the current status is also presented. Furthermore the inherent advantages and disadvantages of the reflectarray topography are presented. In chapter 2, a BST-integrated reflectarray operating at Ka band is presented. Due to the monolithic integration of the tuning element, this design is then extended to V band where a novel interdigital gap configuration is utilized. Finally to overcome loss and phase limitations of …

Hybrid Multi-Objective Optimization Of Left Ventricular Assist Device Outflow Graft Anastomosis Orientation To Minimize Stroke Rate, Blake Lozinski

Electronic Theses and Dissertations

A Left Ventricular Assist Device (LVAD) is a mechanical pump that is utilized as a bridge to transplantation for patients with a Heart Failure (HF) condition. More recently, LVADs have been also used as destination therapy and have provided an increase in the quality of life for patients with HF. However, despite improvements in VAD design and anticoagulation treatment, there remains a significant problem with VAD therapy, namely drive line infection and thromboembolic events leading to stroke. This thesis focuses on a surgical maneuver to address the second of these issues, guided by previous steady flow hemodynamic studies that have …

Theoretical And Experimental Study For Tailoring The Electromagnetic Properties Of Conductive Materials, Jeffrey Jennings

Electronic Theses and Dissertations

Induction in leaded, implanted medical devices exposed to radio frequency (RF) magnetic fields during magnetic resonance imaging (MRI) produce Joule heating in adjacent tissues causing various issues, including death. Given the importance of MRI as a diagnostic tool and the growth in leaded device-related treatments, identification of a solution ensuring their compatibility is of great interest. Electromagnetic (EM) surface property tailoring in lead materials to change their inductive response by adding functionally-graded, heterogeneous surface layers is a possible solution. However, non-uniform EM properties introduce two challenges: the added complexity of analyses and characterization of the graded region. This dissertation addresses …

Investigation Of Flow Field Structures In A Rectangular Channel With A Pin Fin Array, Patrick Tran

Electronic Theses and Dissertations

Pin fin arrays are commonly found in heat exchangers, turbine blades, and electronic heat sinks. Fin arrays are extended surfaces that are used as turbulence promoters by inducing horseshoe vortex (HSV) and von Karman vortex (KV) structures. The horseshoe vortex are primarily studied in the leading edge of the blunt body, whereas the KV are formed in the trailing side. This study presents an experimental investigation of flow field structures and pressure loss on staggered pin fin array in the wake region, where KV are dominate. These flow structures increase the local levels turbulence and generate eddies that promote flow …

Safety, Operational, And Design Analyses Of Managed Toll And Connected Vehicles' Lanes, Moatz Saad

Electronic Theses and Dissertations

Managed lanes (MLs) have been implemented as a vital strategy for traffic management and traffic safety improvement. The majority of previous studies involving MLs have explored a limited scope of the impact of the MLs segments as a whole, without considering the safety and operational effects of the access design. Also, there are limited studies that investigated the effect of connected vehicles (CVs) on managed lanes. Hence, this study has two main objectives: (1) the first objective is achieved by determining the optimal managed lanes access design, including accessibility level and weaving distance for an at-grade access design. (2) the …

Design And Structural Analysis Of Morphing Wings, Nicholas Fernandez

Electronic Theses and Dissertations

Many natural flyers and marine swimmers can morph their wings during a number of unsteady maneuverings. With such wing morphing they are able to control the unsteady aerodynamic forces. A number of man-made flyers, such as unmanned aerial vehicles and micro air vehicles, fly in comparable Reynolds number range, but they are yet to acquire similar morphing capabilities as natural flyers or swimmers. Moreover, the knowledge of fluid structural interaction (FSI) of such morphing wings is not well developed. Hence there is a need to investigate the FSI of morphing wings. In this thesis, a morphing wing was designed and …

Gan Power Devices: Discerning Application-Specific Challenges And Limitations In Hemts, Andrew Binder

Electronic Theses and Dissertations

GaN power devices are typically used in the 600 V market, for high efficiency, high power-density systems. For these devices, the lateral optimization of gate-to-drain, gate, and gate-to-source lengths, as well as gate field-plate length are critical for optimizing breakdown voltage and performance. This work presents a systematic study of lateral scaling optimization for high voltage devices to minimize figure of merit and maximize breakdown voltage. In addition, this optimization is extended for low voltage devices ( < 100 V), presenting results to optimize both lateral features and vertical features. For low voltage design, simulation work suggests that breakdown is more reliant on punch-through as the primary breakdown mechanism rather than on vertical leakage current as is the case with high-voltage devices. A fabrication process flow has been developed for fabricating Schottky-gate, and MIS-HEMT structures at UCF in the CREOL cleanroom. The fabricated devices were designed to validate the simulation work for low voltage GaN devices. The UCF fabrication process is done with a four layer mask, and consists of mesa isolation, ohmic recess etch, an optional gate insulator layer, ohmic metallization, and gate metallization. Following this work, the fabrication process was transferred to the National Nano Device Laboratories (NDL) in Hsinchu, Taiwan, to take advantage of the more advanced facilities there. Following fabrication, a study has been performed on defect induced performance degradation, leading to the observation of a new phenomenon: trap induced negative differential conductance (NDC). Typically NDC is caused by self-heating, however by implementing a substrate bias test in conjunction with pulsed I-V testing, the NDC seen in our fabricated devices has been confirmed to be from buffer traps that are a result of poor channel carrier confinement during the dc operating condition.

Assessment Of A Surface Water Supply For Source And Treated Distribution System Quality, Angela Rodriguez

Electronic Theses and Dissertations

This study focused on providing a source to tap assessment of surface water systems with respect to (i) the use of alternative biomonitoring tools, (ii) disinfection byproduct (DBP) formation and control, and (iii) corrosion control. In the first study component, two water systems were microbiologically evaluated using adenosine triphosphate (ATP) bioluminescence technology. It was determined that microbial ATP was useful as a surrogate for biomonitoring within a surface water system when paired with traditional methods. Although microbial activity differed between distribution systems that used either chloramine or chlorine disinfectant, in both cases flowrate and season affected microbial ATP values. In …

Analysis Of Residual Stress And Damage Mechanisms Of Thermal Barrier Coatings Deposited Via Ps-Pvd And Eb-Pvd, Linda Rossmann

Electronic Theses and Dissertations

Thermal barrier coatings (TBCs) are critical to gas turbine engines, as they protect the components in the hot section from the extreme temperatures of operation. The current industry standard method of applying TBCs for turbine blades in jet engines is electron-beam physical vapor deposition (EB-PVD), which results in a columnar structure that is valued for its high degree of strain tolerance. An emerging deposition method is plasma-spray physical vapor deposition (PS-PVD), capable of producing a variety of customizable microstructures as well as non-line-of-sight deposition, which allows more complex geometries to be coated, or even multiple parts at once. The pseudo-columnar …