Engineering Commons^™

Fuzzy-Logic-Based Robust Speed Control Of Switched Reluctance Motor For Low And High Speeds, Zeki̇ Omaç

Turkish Journal of Electrical Engineering and Computer Sciences

Switched reluctance motor (SRM) is operated at high magnetic saturation to generate large torque. The flux linkage of SRM is a nonlinear function with phase current and rotor position because of the high magnetic saturation. Also, the performance of the speed controller for the SRM driver system can be negatively affected by noise, disturbances, and inertia of load torque. Therefore, the fuzzy speed controller for the SRM driver system was developed in this study. In addition, a dynamic model of SRM was simulated in Matlab/Simulink software. Based on the results obtained in this study, the speed of the SRM was …

Fitting A Recurrent Dynamical Neural Network To Neural Spiking Data: Tackling The Sigmoidal Gain Function Issues, Reşat Özgür Doruk

Turkish Journal of Electrical Engineering and Computer Sciences

This is a continuation of a recent study (Doruk RO, Zhang K. Fitting of dynamic recurrent neural network models to sensory stimulus-response data. J Biol Phys 2018; 44: 449-469), where a continuous time dynamical recurrent neural network is fitted to neural spiking data. In this research, we address the issues arising from the inclusion of sigmoidal gain function parameters to the estimation algorithm. The neural spiking data will be obtained from the same model as that of Doruk and Zhang, but we propose a different model for identification. This will also be a continuous time recurrent neural network, but with …

Robust Compressed Domain Watermarking Algorithm For Video Protection And Authentication In Noisy Channels, Naveen Cheggoju, Vishal Satpute

Turkish Journal of Electrical Engineering and Computer Sciences

This paper introduces a robust and noise-resilient compressed domain video watermarking technique for data authentication and copyright protection. In recent years, watermarking has emerged as an essential technique to be equipped with data transmission. The main challenge pertaining to transmission is to protect the watermark from noise introduced by the channel. Here, we address this issue by watermark replication and by using the independent pass coding (INPAC) algorithm for compression. A replicated watermark is embedded into the video by the proposed blind video watermarking algorithm and then the watermarked video is compressed by the INPAC algorithm. The compressed video is …

Speech Enhancement Using Adaptive Thresholding Based On Gamma Distribution Of Teager Energy Operated Intrinsic Mode Functions, Özkan Arslan, Erkan Zeki̇ Engi̇n

Turkish Journal of Electrical Engineering and Computer Sciences

This paper introduces a new speech enhancement algorithm based on the adaptive threshold of intrinsic mode functions (IMFs) of noisy signal frames extracted by empirical mode decomposition. Adaptive threshold values are estimated by using the gamma statistical model of Teager energy operated IMFs of noisy speech and estimated noise based on symmetric Kullback--Leibler divergence. The enhanced speech signal is obtained by a semisoft thresholding function, which is utilized by threshold IMF coefficients of noisy speech. The method is tested on the NOIZEUS speech database and the proposed method is compared with wavelet-shrinkage and EMD-shrinkage methods in terms of segmental SNR …

A Novel Hybrid Teaching-Learning-Based Optimization Algorithm For The Classification Of Data By Using Extreme Learning Machines, Ender Sevi̇nç, Tansel Dökeroğlu

Turkish Journal of Electrical Engineering and Computer Sciences

Data classification is the process of organizing data by relevant categories. In this way, the data can be understood and used more efficiently by scientists. Numerous studies have been proposed in the literature for the problem of data classification. However, with recently introduced metaheuristics, it has continued to be riveting to revisit this classical problem and investigate the efficiency of new techniques. Teaching-learning-based optimization (TLBO) is a recent metaheuristic that has been reported to be very effective for combinatorial optimization problems. In this study, we propose a novel hybrid TLBO algorithm with extreme learning machines (ELM) for the solution of …

Modeling And Evaluating Cost-Effectiveness Of Host-Microbiome Investigations, Renuka Panchagavi

Dissertations

Cost-effectiveness modeling accounts for how expenditures impact outcomes and is an appropriate step towards efficacy of the different methods used for modeling the dynamics of microbial communities. This will help to identify challenging aspects of microbiome studies and the associated costs, including the major differences in research designs (cross-sectional or time series-based) used for conducting such studies. The two major stages of our investigation were to first collect and model cost variable data for microbiome investigations, and then to evaluate how trade-offs related to sample size and expenditures impact investigational outcomes. We screened different potential sources of data for microbiome …

Mechanical Behavior Of Cement Paste At Nanoscale - Reactive Molecular Dynamics Modeling And Experimental Corroborations, Ingrid M. Padilla Espinosa

Dissertations

Concrete is the most used material for construction, and it is the most produced man-made product in the world. Concrete makes the contemporary architecture of the world conceivable and brings significant development to communities. Nevertheless, there are many downsides to the use of concrete such as the large amount of energy and water used in its production, large carbon footprint, shrinkage and expansion that can cause cracking and other failure mechanisms, and the required use of large amounts of material to ensure stability of concrete structures. These drawbacks create the need for engineering and tailoring the properties of concrete. An …

Deterioration Modelling Of Bridges On Brm 5.2.3, Sudhir Palle, Theodore Hopwood Ii

Kentucky Transportation Center Research Report

The Kentucky Transportation Cabinet (KYTC) initiated the study KYSPR 17-532, “Deterioration Modelling of Bridges on BrM 5.2.3,” so it could receive assistance identifying and employing bridge deterioration and cost forecast modeling for its bridge maintenance program. The Kentucky Transportation Center (KTC) was to help coordinate KYTC in adapting BrM 5.2.3’s deterioration and cost modelling features and update the existing guide material to reflect all changes for BrM 5.2.3. This study included acquiring access and becoming familiar with AASHTO Bridge Management (BrM 5.2.3) software. It was also to explore opportunities for any training on BrM and BrM 5.2.3’s deterioration and cost …

Kentucky Traffic Collision Facts 2018, Eric R. Green, Paul A. Ross, Christopher L. Blackden, Kentucky State Police

Kentucky Transportation Center Research Report

KENTUCKY’S TRAFFIC COLLISION FACTS report is based on collision reports submitted to the Kentucky State Police Records Branch. As required by Kentucky Revised Statutes 189.635, “every law enforcement agency whose officers investigate a vehicle accident of which a report must be made...shall file a report of the accident...within ten days after investigation of the accident upon forms supplied by the bureau.” The stated purpose of this requirement is to utilize data on traffic collisions for such purposes as will improve the traffic safety program in the Commonwealth. Data contained in this report are based solely on the observations and judgements …

Non-Invasive Microwave And Millimeter Wave Reflectometry And Imaging For Human Skin Diagnosis And Materials Characterization, Yuan Gao

Doctoral Dissertations

"Microwave and millimeter wave reflectometry and synthetic aperture radar (SAR) imaging techniques have been successfully applied in many applications, such as nondestructive testing and evaluation (NDT&E), security inspection and medical diagnosis. In this dissertation, the feasibility of using microwave and millimeter reflectometry and SAR imaging for burn diagnosis is investigated through both simulations and measurements, with promising results. To correctly model the interaction between electromagnetic waves and skin, the proper knowledge of the complex permittivity of healthy skin is critically important. To this end, the common used measurement methods for in vivo skin complex permittivity are reviewed and analyzed in …

Development And Characterization Of Nanostructured Steels And High Entropy Alloys For Nuclear Applications, Andrew Kalevi Hoffman

Doctoral Dissertations

"Nuclear reactor materials are subjected to a harsh environment including high temperatures and radiation fluences. In order to extend the lifetime of current light water reactors (LWRs) and realize the development of advanced Gen IV nuclear reactors new materials must be developed which can withstand such an environment. This thesis involves two approaches to solving this materials problem: advanced manufacturing of current commercial alloys using severe plastic deformation (SPD) and the development of new advanced high entropy alloys (HEAs).

Because SPD is effective at achieving grain refinement, this technique was used to obtain material having a high volume fraction of …

Test 2211: John Deere 5125ml, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2209: Case Ih Farmall 70a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2208: Case Ih Farmall 60a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2210: John Deere 5090e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2208a: New Holland Workmaster 60, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Assessing Impact And Blast Resilience Of Polymer Coated Cementitious Materials, Murtaza Nalwala, Gabriel Nsengiyumva, Yong-Rak Kim

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

RESEARCH MOTIVATION: The bridge piers are highly vulnerable to the impact and blast loads. The position in which they are constructed makes it difficult to install protective devices around them. By the current AASHTO standard, it is possible to under-design bridge piers for commercial vehicle impacts and other events such as blast.

OBJECTIVE: To improve impact and blast resilience of bridge piers using polymeric coatings.

CONCLUSION • Polymer coating of Portland cement concrete can be achieved with a good bonding. • The polymeric coating seem to improve impact resilience of Portland cement concrete by increasing absorbed impact energy (i.e., area …

Nebraska Summary: S1181 Fendt 942, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1179 Fendt 936, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1177 Fendt 930, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1157 John Deere 5125ml, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S1160 John Deere 6195m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Proceedings Of The 19th Annual Early Career Technical Conference (Front Matter), Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. i-xii

Section 1: Materials & Design, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 1-21

Section 2: Materials & Testing, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 22-41

Section 3: Robotics & Computing, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 42-75

Section 4: Sustainability & Design, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 76-95

Section 6: Thermal Sciences, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 113-145

Section 5: Materials, Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama; pp. 96-112

Proceedings Of The 19th Annual Early Career Technical Conference (Complete Issue), Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the 19th Annual Early Career Technical Conference, November 2-3, 2019. School of Engineering, University of Alabama at Birmingham, Birmingham, Alabama