Engineering Commons^™

Simulation Framework And Potential Field Relocation For Systems Of Shared Autonomous Vehicles, Landon Blaine Wright

Theses and Dissertations

Shared autonomous vehicles present a significant opportunity to change the way that urban mobility is viewed by society. By providing a shared mobility platform at a cost lower than has previously been obtainable there are significant possibilites to enable a new era of mobility for consumers. This opportunity, however, comes with significant risks in the form of emissions and increased road usage. Understanding how the risks and benefits of shared autonomous vehicles can be balanced is crucial to be able to adequately prepare for their introduction. One of the primary ways to understand the interplay between the risks and benefits …

Characterization Of Dislocation - Grain Boundary Interactions Through Electron Backscatter Diffraction, Landon Thomas Hansen

Theses and Dissertations

Further understanding of dislocation-GB interactions is critical to increasing the performance of polycrystalline metals. The research contained within this dissertation aims to further dislocation-GB interaction understanding through three research studies. First, the effect of noise in EBSPs on GND calculations was evaluated in order to improve dislocation characterization via HR-EBSD. Second, the evolution of GNDs and their effects on back stress was studied through experimental and computational methods applied to tantalum oligo specimens. Third, statistical analysis was used to evaluate grain parameters and current GB transmission parameters on their correlation with dislocation accumulation.

Distribution Of Tremorogenic Activity Among The Majorsuperficial Muscles Of The Upper Limb Insubjects With Essential Tremor, David Jordan Standring

Theses and Dissertations

Optimized peripheral tremor suppression could address many limitations of surgical or medicinal treatments of Essential Tremor, however it is not well understood how the tremorogenic activity is distributed among the muscles of the upper limb, and therefore how to optimize such suppression. We recorded electromyographic (EMG) activity in the 15 major superficial muscles from the shoulder to the wrist while subjects performed postural and kinetic tasks similar to activities of daily living. We calculated the power spectral density and computed the total power in the tremor band (4"12 Hz) for each muscle, from which we determined the distribution of tremorogenic …

The Effect Of Subglottic Stenosis On The Aerodynamic, Acoustical, And Vibratory Output Of Synthetic Vocal Fold Models, Benjamin Allen Hilton

Theses and Dissertations

There are many conditions and diseases that affect voice production. One of these, subglottic stenosis (SGS), is characterized by a narrowing of the trachea near the cricotracheal junction. SGS causes dyspnea (labored breathing) and frequently surgery is necessary to eliminate the airway obstruction. SGS is also believed to adversely affect voice quality. While significant research has been conducted to study the effect of SGS on breathing, relatively few studies concerning its effect on voice production have been performed. The purpose of this research was to provide quantitative results concerning the predicted effects of SGS on vocal fold (VF) vibration and …

Comparison Of Heat Generation Models In Finite Element Analysis Of Friction Welding, Richard Verile Livingston

Theses and Dissertations

Finite element models of friction welding can be used to estimate internal conditions of welds which are useful for weld analysis and developing experimental welding procedures. Many modeling techniques are used to accomplish these goals, each with relative strengths and weaknesses. A comparative analysis of friction welding models using different heat generation methods is presented. The three different heat generation methods examined were viscoplastic friction, constant steady-state generation, and experimentally measured power data. The models were compared against each other using three output measurements: temperature, axial force, and upset. The friction model predicted temperatures within 40 degrees C. Temperature accuracy …

Significance Of The Rates Of Atmospheric Deposition Around Utah Lake And Phosphorus-Fractionation Of Local Soils, Joshua Glen Reidhead

Theses and Dissertations

Eutrophic Utah Lake receives a large nutrient load from a variety of sources, includingtreated wastewater discharges, runoff and tributaries, recycling from bottom sediments andAtmospheric Deposition (AD). AD was the focus of this study and was comprised of twocomplementary parts. First was a study of nitrogen and phosphorus depositions from theatmosphere, and second was a study of phosphorous as contained in soils near Utah Lake viafractionation methods.The soil samples were found to contain approximately 1,000 mg-P/kg soil for totalphosphorus (TP). A separate phosphorus (P) fractionation gave slightly higher values, excludingthe residual P, we are 95% confident that one gram of sample …

A Displacement Controlled Fatigue Test Method For Additively Manufactured Materials, Mohammad Masud Parvez, Yitao Chen, Sreekar Karnati, Connor Coward, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

A novel adaptive displacement-controlled test setup was developed for fatigue testing on mini specimens. In property characterization of additive manufacturing materials, mini specimens are preferred due to the specimen preparation, and manufacturing cost but mini specimens demonstrate higher fatigue strength than standard specimens due to the lower probability of material defects resulting in fatigue. In this study, a dual gauge section Krouse type mini specimen was designed to conduct fatigue tests on additively manufactured materials. The large surface area of the specimen with a constant stress distribution and increased control volume as the gauge section may capture all different types …

Ionic Conductivity Behavior By Activated Hopping Conductivity (Ahc) Of Barium Aluminoborosilicate Glass–Ceramic System Designed For Sofc Sealing, M. J. Da Silva, W. M. Pontuschka, J. F. Bartolomé, P. Jasinski, J. Karczewski, Signo Tadeu Dos Reis

Materials Science and Engineering Faculty Research & Creative Works

Non-conducting BaO-B₂O₃ -Al₂O₃ -SiO₂ parent glasses designed for solid oxide fuel cell (SOFC) sealing applications were prepared using the melt-quenching technique. The glass formation region was determined according to phase equilibrium relations and was found to be in the composition range 70BaO-(x) Al₂O₃ -(10−x) B₂O₃ -₂₀SiO₂ where 3.0 < x < 6.0 wt.%. The conductivity values obtained conductivity ranged from 10 −5 to 10 −10 S/cm at temperatures between 600 and 850 °C. The batch compositions presented a threshold of dc conductivity near 70BaO wt% with a quasi linear behavior with the decrease of the BaO content. Different values of conduction activation energy were observed at temperatures above the glass transition temperature (T g ) (up to 700 °C), which were attributed to the thermal bond-breaking of non-bridging oxygen (NBO) defects. The experimental results of the electrochemical characterization by impedance spectroscopy of glass–ceramic interfaces with yttria-stabilized zirconia (YSZ) acting as solid ionic conductor electrolyte are presented and discussed.

Triple-Junction Solar Cells : In Parallel., Levi C Mays

Electronic Theses and Dissertations

This paper looks into the current inefficiency of solar cells and attempts a few alternative solar cell structures in order to provide a more effective source of renewable energy. Currently, multi-junction solar cells are being developed to capture the sun’s light more efficiently. One of the ideas in this paper is to add a window to see if the addition of such a layer into a junction will increase the voltage while maintaining nearly the same current output. Central to this paper is the rearranging of the conducting layers of the multi-junction cell so that the junctions can be connected …

Purification Of Biomass Hydrolyzates For The Promotion Of Xylose Diester Formation, Laura Fernandez

Electronic Theses and Dissertations

The application of a novel xylose isolation procedure using phenyl boronic acid esterification has been limited to the hydrolyzates of low extractive biomasses like hardwoods and agricultural resides. Hydrolyzates with lower sugar and higher extractive concentrations, like softwoods, have not yielded xylose, or even xylose diester (XDE), the first intermediate product in the new process, under the same conditions. This research applied evaporation concentration, adsorbent separation and membrane filtration to these lower performing biomass hydrolyzates to maximize the yield of the XDE formation step of the new xylose extraction process. Lab-scale tests of these techniques were applied to pine hydrolyzate …

Fluid Flow Analysis Of Diluted Evaporating American Whiskey Droplets., Martin J. Brown Vi

Electronic Theses and Dissertations

The recent discovery of the unique structures, whiskey webs, formed when the evaporation of diluted American whiskey, has raised many questions as to the nature of the structures. Their formation process follows as such: (1) dilution of the whiskey to form nanoaggregates, (2) formation of a monolayer at the air-liquid interface, (3) chaotic ethanol evaporation caused monolayer collapse (via dynamic pressure), (4) bulk fluid evaporation caused monolayer collapse (via reduction of surface area), where the web-like structures reside on the surface, and finally, (5) web-like structures deposit on the substrate. The webs imaged via SEM had a striking resemblance to …

Microstructural Effects On Photocatalytic Performance In Ag3po4/Bi2moo6 Z-Scheme Photocatalyst Systems, Kaleab Mengesha Ayalew

UNLV Theses, Dissertations, Professional Papers, and Capstones

As the world population continues to grow and access to modern industry become increasingly common, humanity finds itself amid an environmental and energy crisis. Natural resources, such as clean water are getting scarce. Currently, the development of high efficiency, green energy sources, and eco-friendly methods for water treatment have become a nonelective task. As a result, photocatalysis, as one of the most promising technologies in utilizing solar energy and pollutant removal, has attracted considerable attention.

However, the practical application of photocatalysis is still elusive because of the difficulty of finding an individual material that can satisfy all the requirements for …

Investigation Of Efficiency Loss Of Distributed Solar Power Due To Soiling And Efficiency Recovery By Rainfall, Amanda Mayumi Tanaka

UNLV Theses, Dissertations, Professional Papers, and Capstones

As the concern with global warming increases causing the need for CO2 reduction, renewable energy is of great interest as it has lower carbon footprint when compared to conventional sources (natural gas, coal, oil and nuclear). Solar energy has been drawing worldwide attention since it can transform sunlight directly into electricity with the use of photovoltaic (PV) cells. However, this technology has some drawbacks that need to be addressed including dust deposition on solar panels, also known as soiling. Soiling can decrease PV panel’s efficiency thereby resulting in less energy production. The soiling rates are very site specific and depend …

The Effect Of Implant Conformity On Muscle Force Requirements In The Implanted Knee, Grace Mcconnochie

Boise State University Theses and Dissertations

Implant geometry is a significant factor in determining knee stability and patient satisfaction following total knee replacement (TKR). Ineffective muscle recruitment, impaired joint functionality and increased implant wear are consequences of an unstable knee replacement. Current knee laxity evaluation techniques are limited in their ability to account for the muscular response to knee instability. This study utilizes a subject specific lower-body musculoskeletal finite element (FE) model with dynamic muscle loading to evaluate implant laxity during activities of daily living. The effect of varying implant conformity on the muscle forces required to maintain a target kinematic profile during simulated laxity testing …

Understanding Self-Assembly And Charge Transport In Organic Solar Cells Through Efficient Computation, Evan Miller

Boise State University Theses and Dissertations

Organic solar cells capable of sustainably generating electricity are possible if: (1) The structures assembled by photoactive molecules can be controlled, and (2) The structures favorable for charge transport can be determined. In this dissertation we conduct computational studies to understand relationships between organic solar cell compounds, processing, structure and charge transport. We advance tools for encapsulating computational workflows so that simulations are more reproducible and transferable. We find that molecular dynamic simulations using simplified models efficiently predict experimental structures. We find that the mobilities of charges through these structures—as determined by kinetic Monte Carlo simulations—match qualitative trends expected with …

Dynamic Modeling Of A Suspended And Shock Isolated System In Seismic Loading, Emilie Murphy

Boise State University Theses and Dissertations

A dynamic model for a suspended and shock isolated system is derived and implemented in MATLAB’s Simulink software. The purpose of this implementation is to create a design tool which is modularized to be able to accommodate any configuration of a similar system in any kind of loading. The design tool is used to compute the level of acceleration experienced at specific points in space within the system in the presence of seismic events, as typified by the dynamic displacement caused by the Sumatra, Indonesia earthquake of 2007. It is determined that under this 8.4 magnitude earthquake, accelerations within the …

Incremental Processing For Improving Conversational Grounding In A Chatbot, Aprajita Shukla

Boise State University Theses and Dissertations

Current Digital Personal Assistants can be quite efficient while performing routine tasks like setting up reminders and looking up information. However, they do not attempt to establish common ground–the process of establishing and building mutual understanding–and require a significant amount of initial data to learn how to understand user intent. In this thesis, an incremental processing framework is leveraged through a chatbot interface which updates its understanding state at each inputted word, asks the user to clarify input when the system is unsure and prompts user to give feedback several times during an interaction, all of which are instrumental in …

Parameter Estimation And Dynamic State Observer Design For Vapor Compression Systems, Travis D. Pruitt

Boise State University Theses and Dissertations

Between cooling our house, our workplace, and keeping our food cold both in home and commercially (among other uses), the vapor compression cycle (VCC) is a common method for removing heat from various environments and it accounts for a significant amount of the energy used throughout the world. Therefore, with an ever-growing demand for more efficient processes and reduced energy consumption, improving the ability to accurately model, predict the performance of, and control VCC systems is beneficial to society as whole.

While there is much information available regarding the performance for some of the components found in VCC systems, much …

Development Of A Statistical Shape-Function Model Of The Implanted Knee For Real-Time Prediction Of Joint Mechanics, Kalin Gibbons

Boise State University Theses and Dissertations

Outcomes of total knee arthroplasty (TKA) are dependent on surgical technique, patient variability, and implant design. Non-optimal design or alignment choices may result in undesirable contact mechanics and joint kinematics, including poor joint alignment, instability, and reduced range of motion. Implant design and surgical alignment are modifiable factors with potential to improve patient outcomes, and there is a need for robust implant designs that can accommodate patient variability. Our objective was to develop a statistical shape-function model (SFM) of a posterior stabilized implant knee to instantaneously predict output mechanics in an efficient manner. Finite element methods were combined with Latin …

Oxidation Behavior Of Zirconium Alloys In Transient Conditions, Jordan Lee Vandegrift

Boise State University Theses and Dissertations

The effect of sample geometry, welding strategies, atmosphere, plastic deformation, and rapid heating on the oxidation behavior of zirconium alloys has been investigated in this work. The goal of this work was to determine which zirconium alloy would be best suited as nuclear fuel cladding material in the Transient Reactor Test (TREAT) facility at the Idaho National Laboratory (INL), which has unique operating conditions compared to typical reactors. TREAT is air-cooled, operates at high temperatures (400-600 °C), and produces rapid transients (≤ 700 ^°C/_s). Additionally, TREAT’s cladding geometry is unique in that it has chamfers and welds. …

Exploring The Use Of Data From Newer Technologies In Road Design, Mahamudul Hasan

Boise State University Theses and Dissertations

The use of Light Detection and Ranging (Lidar) is widespread currently all over the world including the United States. Though on-the-ground surveying and photogrammetric surveying are the more common methods to acquire terrain information, Lidar data is being increasingly used for this purpose due to its various advantages. Various research indicates that the accuracy of Lidar data has increased enough to make its use suitable for diverse applications. One potential application that is explored in this research is the use of terrain models generated from Lidar data in road design. To make such use possible we need to be assured …

Minos: Unsupervised Netflow-Based Detection Of Infected And Attacked Hosts, And Attack Time In Large Networks, Mousume Bhowmick

Boise State University Theses and Dissertations

Monitoring large-scale networks for malicious activities is increasingly challenging: the amount and heterogeneity of traffic hinder the manual definition of IDS signatures and deep packet inspection. In this thesis, we propose MINOS, a novel fully unsupervised approach that generates an anomaly score for each host allowing us to classify with high accuracy each host as either infected (generating malicious activities), attacked (under attack), or clean (without any infection). The generated score of each hour is able to detect the time frame of being attacked for an infected or attacked host without any prior knowledge. MINOS automatically creates a personalized traffic …

Effect Of Subgrade Conditions On Pavement Analysis And Performance Prediction: A Study For Idaho Conditions, Md Jibon

Boise State University Theses and Dissertations

The Mechanistic-Empirical (M-E) pavement design approach detailed in the Mechanistic-Empirical Pavement Design Guide (MEPDG), and subsequently implemented through AASHTOWare^® Pavement ME Design relies extensively on detailed material properties that ultimately govern the analysis and performance prediction results. For unbound materials like soils and aggregates, Resilient Modulus (M_R) is the most critical input parameter affecting layer response under vehicular and environmental loading. Representing a material’s ability to ‘recover’ after loading, resilient modulus is determined in the laboratory through repeated load triaxial testing. Although the original test protocol to measure the resilient modulus value of a soil or aggregate …

Investigation Of Graphene Interconnections For Multifunctional Reconfigurable Antenna Beam Steering, Joshua R. Perkins

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

In high frequency, high-performance wireless communications, direct line of sight antennas are common. The issue with the line of sight antennas is the need to redirect the physical antenna to achieve the best possible reception. Classical redirections are done by mechanical movements: hand tuning and motors. Our multi-functional re-configurable antenna (MRA) concept allows for electrical and non-mechanical antenna reorientation. This work investigates two important concepts in the development and enhancement of future MRA devices: special, non-interfering, control signal circuitry and nano-sized switching devices that are controlled by the special circuitry. The investigation was conducted with the use of commercially available …

Techniques For Using Internal Strain-Energy Storage And Release Inorigami-Based Mechanical Systems, Mary Elizabeth Wilson

Theses and Dissertations

The objective of this thesis is to develop and demonstrate techniques for self-deployment of origami-based mechanical systems achieved through internal strain-energy storage and release, with special application to medical implant devices. The potential of compliant mechanisms and related origami-based mechanical systems to store strain-energy make them ideal candidates forapplications requiring an actuation or deployment process, such as space system arrays and minimally invasive surgical devices. The objective of this thesis is achieved by first categorizing differentdeployment methods in origami-based, deployable mechanisms and then further exploring the use of strain energy to facilitate actuation in deployable mechanisms. With this understanding inplace, …

A Study Of Human Balance And Coordination Using A Head Mounted Display, Daniel Gracia De Luna

Theses and Dissertations

Virtual Reality (VR) is growing with new technologies and applications. The new technologies help the user to feel more immersed in virtual environments, but interaction and immersion is an area that has not been well studied. Immersion is the feeling and reaction of users while they are in a virtual environment. This investigation is focused on the study of the human balance and coordination when human subjects are inside a virtual environment. Over 60 subjects are studied under an experiment, where their trajectory is captured and analyzed to identify possible differences or similitudes between male and female subjects.

Cybersecurity Education In Utah High Schools: An Analysis And Strategy For Teacher Adoption, Cariana June Cornel

Theses and Dissertations

The IT Education Specialist for the USBE, Brandon Jacobson, stated:I feel there is a deficiency of and therefore a need to teach Cybersecurity.Cybersecurity is the “activity or process, ability or capability, or state whereby information and communications systems and the information contained therein are protected from and/or defended against damage, unauthorized use or modification, or exploitation” (NICE, 2018). Practicing cybersecurity can increase awareness of cybersecurity issues, such as theft of sensitive information. Current efforts, including but not limited to, cybersecurity camps, competitions, college courses, and conferences, have been created to better prepare cyber citizens nationwide for such cybersecurity occurrences. In …

Predicting Hardness Of Friction Stir Processed 304l Stainless Steel Using A Finite Element Model And A Random Forest Algorithm, Tyler Alan Mathis

Theses and Dissertations

Friction stir welding is an advanced welding process that is being investigated for use in many different industries. One area that has been investigated for its application is in healing critical nuclear reactor components that are developing cracks. However, friction stir welding is a complicated process and it is difficult to predict what the final properties of a set of welding parameters will be. This thesis sets forth a method using finite element analysis and a random forest model to accurately predict hardness in the welding nugget after processing. The finite element analysis code used and ALE formulation that enabled …

The Influence Of Incorporation Of Mn On The Pitting Corrosion Performance Of Crfeconi High Entropy Alloy At Different Temperatures, H. Torbati-Sarraf, Mitra Shabani, Paul D. Jablonski, Garrett J. Pataky, A. Poursaee

Publications

The electrochemical behavior and susceptibility to pitting corrosion of CrFeCoNi and CrMnFeCoNi high entropy alloys were studied in a 0.1 M NaCl solution at temperatures ranging from 25 to 75 °C. Electrochemical measurements revealed that CrMnFeCoNi is more susceptible to oxide film breakdown and localized corrosion compared to CrFeCoNi. Post corrosion microscopic observations showed severe pitting corrosion for CrMnFeCoNi in higher temperatures compared to CrFeCoNi. Based on in-depth XPS profile measurements on the remaining oxide films, this behavior was attributed to the depletion of Cr in the oxide film and detrimental presence of Mn in the matrix solid solution of …

Residential Electricity Management And Protection System, Ejimonu Kosisochukwu Gabriel

Journal of International Technology and Information Management

The Residential Electricity Monitoring System is an electricity meter connected to the Internet to provide real time data on the power system in your home. The REMS is designed to replace the distribution board allowing it to conduct a series of tests on the quality of the electricity supply to your home/facility and, within your home detect basic wiring faults and allow owners and service providers to identify potential problems with the electrical systems.

The electrical monitoring system finally puts proper electrical control into the hands of the home owner by providing him with the ability to control power distribution …