Engineering Commons^™

Strength And Durability Of Hybrid Fibre Reinforced Binary Blend Geopolymer Concrete, Namasivayam Ganesan, P V Indira, R Sahana

International Conference on Durability of Concrete Structures

This paper deals with an investigation on the influence of hybrid fibres on the strength and durability of binary blend geopolymer concrete. Geopolymer concrete was prepared using Fly ash and GGBS as source material and mix design was carried out as per the guidelines of Professor Rangan of Curtin University, Australia. Different fly ash-GGBS proportions namely 50-50%, 60-40%, 70-30%, 80-20% and 90-10% were considered. The tests on Geopolymer concrete reveal that the compressive strength increases as the percentage of GGBS increases up to 30%. Hence the combination of 70% fly ash and 30% GGBS was considered as a base material. …

Influence Of Sulfide On The Onset Of Chloride-Induced Corrosion Of Steel Reinforcement In Alkali-Activated Slags., Maria Criado, Shishir Mundra, Susan Andrea Bernal, John Lloyd Provis

International Conference on Durability of Concrete Structures

In alkali-activated slags (AAS), where ground granulated blast furnace slag is used as the main precursor, the presence of reduced sulfur species yields a highly reducing pore solution environment. This study investigates the influence of sulfide on steel passivation in alkali-activated slag mortars immersed in alkaline (1 M NaOH) and alkaline chloride-rich (1 M NaOH with 5 M NaCl) solutions, and the dependency of chloride-induced pitting on the immersion time and the concentration of sulfide in simulated alkali-activated slag pore solutions (containing 0.80 M OH- and 0 M, 0.01 M and 0.45 M HS- ) by means of electrochemical techniques. …

Impact Of Water Content On The Performance Of Alkali-Activated Slag Concretes, Susan A. Bernal, John L. Provis, Jannie S.J. Van Deventer

International Conference on Durability of Concrete Structures

In this study, we report the effect of varying the water/binder (w/b) ratio on the performance of sodium silicate activated concretes. Compressive strength development and water transport properties of these concretes were assessed, along with their resistance to carbonation. The results demonstrate that varying the water content within a reasonable range induced negligible changes in the compressive strengths of these concretes, when a constant paste content was used. A direct correlation between the w/b ratio and the amount of permeable voids in the concretes was not identified. The carbonation behaviour of these concretes changes prominently depending on the CO2 concentration …

Internal Curing By Sap In Ultra-High Strength Concrete With Cement-Silica Fume-Fly Ash Binder, Jianhui Liu, Caijun Shi, Xianwei Ma

International Conference on Durability of Concrete Structures

Super-absorbed polymer (SAP) is an effective internal curing materials for reducing autogenous shrinkage and improving cracking resistance of ultra-high-strength concrete (UHSC). This study investigated the compressive strength, shrinkage properties of UHSC with cement–silica fume–fly ash binder. The composition of the binder was designed using seven-batch factorial design method. The relationships between the binder composition and the properties were expressed in contours. Results showed that, silica fume could improve the compressive strength and total shrinkage of UHSC. However fly ash reduced the compressive strength and total shrinkage of UHSC to certain extent. On the other hand, under the internal curing of …

Design Of Ternary Blend High-Volume Fly Ash Concrete Mixes Using Hydrated Lime, Chamila Gunasekara, David Law, Sujeeva Setunge

International Conference on Durability of Concrete Structures

The increase of carbon emission due to annual growth of Portland cement (PC) production has enforced research into the development of sustainable green concrete using a range of readily available industrial waste materials. The present study is focused on developing two high volume fly ash (HVFA) concretes with cement replacement levels 65% (HVFA‒65) and 80% (HVFA‒80). Initially, the required lime for both HVFA concrete mixes were determined, and then the optimized mix design identified, based on 28-day strength, by varying the fly ash‒lime combination. The optimized mixes achieved a compressive strength of 53MPa and 40MPa, for HVFA‒65 and HVFA‒80 concretes, …

Compressive Strength, Free Expansion And Shrinkage Of Expansive Concrete Containing Fly Ash, Warangkana Saengsoy, Rachot Chatchawan, Somnuk Tangtermsirikul

International Conference on Durability of Concrete Structures

This study is aimed to investigate effect of fly ash on compressive strength, free expansion and shrinkage of expansive concrete. High CaO and low CaO fly ashes are used in this study. The replacement percentages of total binders by fly ash are 0 and 30% by weight. The replacements of expansive additive are 0, 20 and 30 kg/m³ of concrete. The test results revealed that the use of fly ash especially the high CaO fly ash can enhance expansion of expansive concrete at early age. The use of fly ash also reduces shrinkage at long term of the expansive …

Carbonation In Alternative Cementitious Materials: Implications On Durability And Mechanical Properties, Prasanth Alapati, Kimberly E. Kurtis Dr.

International Conference on Durability of Concrete Structures

Understanding the rate and implications of carbonation on strength and durability in alternative cementitious materials (ACMs) is critical in designing ‘green’ concretes for intended service lives. In this paper, three commercially available ACMs, including one calcium aluminate cement (CAC), one calcium sulfoaluminate belite cement (CSA), and one alkali-activated binder using class C fly ash (AA), were evaluated against one portland cement (OPC). Thermogravimetric analysis (TGA) and x-ray diffraction (XRD) techniques were used to understand the effect of carbonation on ACM paste composition. Water sorption tests on both carbonated and uncarbonated cement mortar showed a significant reduction in porosity of this …

Effects Of Temperature And Curing Duration On The Stability Of Slag Cements In Combined Chloride-Sulphate Environments, Joseph Onah Ukpata, P. A. M. Basheer, Leon Black

International Conference on Durability of Concrete Structures

This experimental study investigates the effects of temperature and curing duration on the stability of slag blended cement systems exposed at 20 °C and 38 °C to combined sodium chloride (30 g/L) – sodium sulphate (3 g/L) solutions. Two slags, designated as slag 1 and 2, having CaO/SiO₂ ratios of 1.05 and 0.94, were respectively blended with Portland cement CEM I 52.5R at 30 wt.% replacement level. Mortar prisms and cubes with w/b ratio of 0.5 and binder/aggregate ratio of 1:3 were then prepared for length and mass changes. The samples were cured in lime water for either 7 …

Usu To Host Intermountain Biological Engineering Conference | College Of Engineering, Utah State University

College of Engineering News

Utah State University’s Department of Biological Engineering will host a regional conference featuring academic, industry, and government research in biological engineering on Saturday, Nov. 9. About 75 faculty, staff and students will engage with industry researchers and government employees in the daylong event on the USU Logan campus.

Periodic Operation Of A Dynamic Dna Origami Structure Utilizing The Hydrophilic–Hydrophobic Phase‐Transition Of Stimulus‐Sensitive Polypeptides, Marisa A. Goetzfried, Kilian Vogele, Andrea Mückl, Marcus Kaiser, Nolan B. Holland, Friedrich C. Simmel, Tobias Pirzer

Chemical & Biomedical Engineering Faculty Publications

Dynamic DNA nanodevices are designed to perform structure‐encoded motion actuated by a variety of different physicochemical stimuli. In this context, hybrid devices utilizing other components than DNA have the potential to considerably expand the library of functionalities. Here, the reversible reconfiguration of a DNA origami structure using the stimulus sensitivity of elastin‐like polypeptides is reported. To this end, a rectangular sheet made using the DNA origami technique is functionalized with these peptides and by applying changes in salt concentration the hydrophilic–hydrophobic phase transition of these peptides actuate the folding of the structure. The on‐demand and reversible switching of the rectangle …

Three Dimensional Object Detection Approaches For Indoor Navigation Aid, Junxiu Zhou

Theses and Dissertations

This dissertation aims to develop object detection approaches for an indoor navigation aid called smart cane. The goal of the object detection approaches is to provide object-level information of the environment to assist the visually impaired people to walk freely in the indoor environment. Although many object detection approaches have been proposed, object detection is still a challenging problem due to a large number of object categories, viewpoint changes, occlusions, cluttered backgrounds, etc. To address these challenges, first, an indoor 3D dataset is collected by using the smart cane navigation aid. Second, indoor objects are broadly divided into two types: …

Information Technology News, Georgia Southern University

Information Technology: News & Publications (2012-2023)

• The Claxton Bank IT Internship

A Review Of 30 Years Of Research Using The Cpd Model, Thomas H. Fletcher

Faculty Publications

The chemical percolation devolatilization (CPD) model for coal pyrolysis was first published in 1989, and a completed version that included the vapor–liquid equilibrium model and cross-linking model was published in 1992. The CPD model was one of three pyrolysis models developed using a lattice model to account for the chemical structure of the coal and was directly based on solid-state ¹³C nuclear magnetic resonance (NMR) measurements of the coal structure. A correlation of coal structure parameters measured by NMR spectroscopy was performed to permit use of the CPD model to determine pyrolysis rates and yields of tars and light …

An Investigation Of High-Speed Consolidation And Repair Of Carbon Fiber - Epoxy Composites Through Ultrasonic Welding, David A. Hoskins

LSU Master's Theses

Adhesive repair of carbon fiber composite structures is commonly done on damaged structures to extend the service life. This method requires careful preparation of the damaged surface with intricate steps to ensure good bonding between the repair patch and the parent structure by means of an adhesive film. As with many forms of composite manufacturing, it is required to perform vacuum bagging, debulking, and a heated cure depending on the resin. All these steps make the repair process costly and time consuming.

In this present work, an alternative method of repair is investigated which explores the experimental feasibility of using …

Thermal-Kinect Fusion Scanning System For Bodyshape Inpainting And Estimation Under Clothing, Sirazum Munira Tisha

LSU Master's Theses

In today's interactive world 3D body scanning is necessary in the field of making virtual avatar, apparel industry, physical health assessment and so on. 3D scanners that are used in this process are very costly and also requires subject to be nearly naked or wear a special tight fitting cloths. A cost effective 3D body scanning system which can estimate body parameters under clothing will be the best solution in this regard. In our experiment we build such a body scanning system by fusing Kinect depth sensor and a Thermal camera. Kinect can sense the depth of the subject and …

Harvesting Energy From Low-Level Vibration Using Alternate Contacts Between Water Drop And Two Dielectric Materials, Jian Yu, David Ma

Energy Harvesting from Infrastructure and Ocean Systems (EHIOS)

Advances in low-power electronics and distributed systems have stimulated significant interests in small-scale power supply systems that generate electricity from ambient environmental energy sources. Recently, the rich electrostatic phenomena at liquid-solid interfaces have spurred renewed interest in harvesting mechanical energy through electrostatics.

Please click Additional Files below to see the full abstract.

The Water Power Technologies Office And Powering The Blue Economy, Bill Mcshane

Energy Harvesting from Infrastructure and Ocean Systems (EHIOS)

No Abstract.

Phasor Measurement Unit Data-Based Steady State And Dynamic Model Estimation, Anas Almunif

USF Tampa Graduate Theses and Dissertations

Phasor measurement units (PMUs) have been put into power grid for real-time monitoring. This research investigates the PMU data for steady state estimation and dynamic model estimation. It focuses on three main research areas to enhance the security of the power system monitoring. First, optimal PMU placement (OPP) problem is developed to minimize the number of PMUs required for the system to be completely observable using mixed integer linear programming and nonlinear programming. Second, PMU measurements are ranked for oscillation monitoring based on two approaches: oscillation mode observability and Prony analysis. Further, the principles, multi-channel data handling, and noise resilience …

Grain Refinement In Iron-Based Materials, Simon Naumovich Lekakh, Von Richards, Ronald J. O'Malley, Jun Ge

Materials Science and Engineering Faculty Research & Creative Works

A process for manufacturing an iron-based alloy comprising forming targeted fine oxide and/or carbide dispersoids in a melt, and sequentially precipitating transition-metal nitrides on the dispersoids for heterogeneous nucleation of equiaxed grains. An iron-based cast alloy having a highly equiaxed fine grain structure.

Impact Of Chemical Compositions On Mechanical Properties Of Modified Asphalt Binders, Mohammad Nazmul Hassan

Student Theses and Dissertations

Modified asphalt binders offer better mechanical performance in field conditions. According to many researchers, nanoclay modified asphalt binders can be a cheaper alternative of currently practiced polymer modified binders. The primary purpose of this study was to observe any changes in asphalt chemistries due to nanoclay modification and explore any correlations that may exist between chemical compositions and mechanical properties. Changes in chemical fractions were found to be source variant. Insoluble Asphaltene contents were observed to increase significantly after aging, whereas the Saturate contents decreased. Correlations were observed between mechanistic properties and chemical compositions. Moreover, aggregate-binder compatibility evaluation showed nanoclay …

Cooperative Navigation Of Fixed-Wing Micro Air Vehicles In Gps-Denied Environments, Gary James Ellingson

Theses and Dissertations

Micro air vehicles have recently gained popularity due to their potential as autonomous systems. Their future impact, however, will depend in part on how well they can navigate in GPS-denied and GPS-degraded environments. In response to this need, this dissertation investigates a potential solution for GPS-denied operations called relative navigation. The method utilizes keyframe-to-keyframe odometry estimates and their covariances in a global back end that represents the global state as a pose graph. The back end is able to effectively represent nonlinear uncertainties and incorporate opportunistic global constraints. The GPS-denied research community has, for the most part, neglected to consider …

Towards Overcoming The Curse Of Dimensionality: The Third-Order Adjoint Method For Sensitivity Analysis Of Response-Coupled Linear Forward/Adjoint Systems, Uncertainty Quantification And Predictive Modeling With Applications To Nuclear Energy Systems, Dan Gabriel Cacuci

Faculty Publications

This work presents the Third-Order Adjoint Sensitivity Analysis Methodology (3rd-ASAM) for response-coupled forward and adjoint linear systems. The 3rd-ASAM enables the efficient computation of the exact expressions of the 3rd-order functional derivatives (“sensitivities”) of a general system response, which depends on both the forward and adjoint state functions, with respect to all of the parameters underlying the respective forward and adjoint systems. Such responses are often encountered when representing mathematically detector responses and reaction rates in reactor physics problems. The 3rd-ASAM extends the 2nd-ASAM in the quest to overcome the “curse of dimensionality” in sensitivity analysis, uncertainty quantification and predictive …

Towards Overcoming The Curse Of Dimensionality: The Third-Order Adjoint Method For Sensitivity Analysis Of Response-Coupled Linear Forward/Adjoint Systems, With Applications To Uncertainty Quantification And Predictive Modeling, Dan Gabriel Cacuci

Faculty Publications

This work presents the Third-Order Adjoint Sensitivity Analysis Methodology (3rd-ASAM) for response-coupled forward and adjoint linear systems. The 3rd-ASAM enables the efficient computation of the exact expressions of the 3rd-order functional derivatives ("sensitivities") of a general system response, which depends on both the forward and adjoint state functions, with respect to all of the parameters underlying the respective forward and adjoint systems. Such responses are often encountered when representing mathematically detector responses and reaction rates in reactor physics problems. The 3rd-ASAM extends the 2nd-ASAM in the quest to overcome the "curse of dimensionality" in sensitivity analysis, uncertainty quantification and predictive …

Comprehensive Second-Order Adjoint Sensitivity Analysis Methodology (2nd-Asam) Applied To A Subcritical Experimental Reactor Physics Benchmark: I. Effects Of Imprecisely Known Microscopic Total And Capture Cross Sections, Daniel Gabriel Cacuci, Ruixian Fang, Jeffrey A. Favorite

Faculty Publications

The subcritical polyethylene-reflected plutonium (PERP) metal fundamental physics benchmark, which is included in the Nuclear Energy Agency (NEA) International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook, has been selected to serve as a paradigm illustrative reactor physics system for the application of the Second-Order Adjoint Sensitivity Analysis Methodology (2nd-ASAM) that was developed by Cacuci. The 2nd-ASAM enables the exhaustive deterministic computation of the exact values of the 1st-order and 2nd-order sensitivities of a system response to the parameters underlying the respective system. The PERP benchmark is numerically modeled in this work by using the deterministic multigroup neutron transport equation discretized …

Porous Radiative Cooling Paint For Building Thermal Management, Yuan Yang

Energy Harvesting from Infrastructure and Ocean Systems (EHIOS)

Surface coating with high solar reflectance and high thermal emittance are attractive for saving energy in buildings. Conventional paints typically have a solar reflactance < 93% due to UV and near infrared absorption. Here we demonstrate a porous PVdF copolymer surface coating that shows high solar reflectance of over 96% and high thermal emittance of 0.97. When it is placed under sunlight, it can be 6 oC cooler than the environment without any electricity.

Conference Program, Huiming Yin, Muhammad R. Hajj, Lei Zuo, David T. Ma

Energy Harvesting from Infrastructure and Ocean Systems (EHIOS)

No abstract provided.

Energy Harvesting For Micromobility Systems, Alex Kattamis, Zachary Lochner,

Energy Harvesting from Infrastructure and Ocean Systems (EHIOS)

No Abstract.

Automated Dynamic Detection Of Self-Hiding Behaviors, Luke Baird

Student Works

Certain Android applications, such as but not limited to malware, conceal their presence from the user, exhibiting a self-hiding behavior. Consequently, these apps put the user’s security and privacy at risk by performing tasks without the user’s awareness. Static analysis has been used to analyze apps for self-hiding behavior, but this approach is prone to false positives and suffers from code obfuscation. This research proposes a set of three tools utilizing a dynamic analysis method of detecting self-hiding behavior of an app in the home, installed, and running application lists on an Android emulator. Our approach proves both highly accurate …

Effects Of Reservoir Conditions And Trace Co-Contaminant Gases On Geological Carbon Sequestration, Ram Kumar

USF Tampa Graduate Theses and Dissertations

Geological carbon sequestration in a saline formation is a promising technology for large-scale carbon dioxide (CO2) mitigation. Several factors such as temperature, pressure, salinity, hydraulic conductivity, and mineralogy of a formation affect the CO2 sequestration in saline formations. These factors can vary widely depending upon the type of formation or the degree of heterogeneity within a formation. In addition to these properties of the repositories, the CO2-rich flue gas streams captured from point sources often contains small amounts of impurities such as sulfur oxides (SOx) and nitrogen oxides (NOx), which may have serious implications on the chemistry of the repositories …

College Of Engineering News, Georgia Southern University

College of Engineering & Computing: News & Publications (2010-2023)

• SPARK Innovation Competition 2019