Engineering Commons^™

Influence Of Electrode Height On Carbon Nanotube Electrochemical Biosensors, Benjamin J. Brownlee

Utah Space Grant Consortium

High sensitivity of electrochemical sensors enables the detection of low concentrations of target analyte. Being able to quickly and accurately detect low concentrations of proteins at point-of-care allows for results to be analyzed more easily and effectively. Having high surface area allows for more analyte to be detected, possibly leading to increased sensitivity. Vertically-aligned carbon nanotubes (VACNTs) were patterned into interdigitated electrodes (IDEs) and then functionalized with the representative protein streptavidin to demonstrate sensing of biotin. Three electrode heights were investigated to determine the influence of electrode height on sensor sensitivity. Cyclic voltammetry and electrochemical impedance spectroscopy were used to …

Evolutionary Nonlinear Model Predictive Control On A Fixed-Wing And Multirotor, Jaron Ellingson, Matthew Haskell

Utah Space Grant Consortium

Real-time model predictive control (MPC) is limited to short time horizons and linear systems because the optimization complexity is too large with long time horizons and nonlinear systems. For this reason, MPC is typically accomplished using linearized models and convex optimization solvers. We seek to explore evolutionary algorithms allowing for nonlinear models and constraints, non-convex costs, and extended time horizons.

Our contributions include extending nonlinear evolutionary MPC to flight vehicles, fixed-wing and multirotor UAVs, as well as enhancing the evolutionary algorithm. We also intend to parameterize the design space of the optimization to reduce solve times. These contributions validate the …

Economic Analysis Of Productivity In The Irish Construction Sector, Kpmg, Fac, Róisín Murphy Dr, Avril Behan

Reports

Important strides to enhance productivity in the construction sector have been taken by both industry and Government in recent years. However, a collaborative, sectoral wide strategy to drive further increases in productivity is required, with the coordinated participation of all stakeholders across the full life cycle of a project. This report, commissioned by the Department of Public Expenditure and Reform (DPER), produced by KPMG and Future Analytics Consulting Ltd. (FAC) and peer reviewed by TU Dublin, aims to understand and address the reasons for low levels of productivity in the Irish construction sector and identify specific recommendations and actions that …

Portable Calorimeter For Fire Experiments, Kayla Collins, Kara Hewson, Christopher Chen, Joel Keddie

Mechanical Engineering

Executive Summary

An oxygen consumption calorimeter works by measuring the heat release rate of a burning substance. This value is calculated by measuring the oxygen and byproducts in smoke from afire.In order to get these values two types of sensors were used. A non-dispersive infrared sensor (NDIR) that measured CO and CO2 and a zirconium O2 sensor were used to find their respective gas concentrations.The design to calculate the heat release rate is focused on maximizing sensor accuracy and portability while simplifying the manufacturing by using off-the-shelf components. The goal included making the system simple to recreate and package in …

Improving Pv Module Efficiency Through Cooling, Blake Bradley

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Improving Pv Module Efficiency Through Cooling, Megan Reynolds

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Solution To Exide Technologies Inbatec Inefficiency, Shixuan Hou, Reagan Gilker, Mary Fairley, Spencer Christian, Covenson Latouche

Chemical Engineering Undergraduate Honors Theses

The inefficiency of the battery charging time in Inbatec Units 1 and 2 in the Exide Technologies Fort Smith was initially investigated by a student team in Fall 2019, and the investigation was continued into Spring 2020. The Exide Technologies facility in Fort Smith, Arkansas utilizes 13 Inbatec units to charge the lead-acid batteries. The Inbatec systems circulate the sulfuric acid solution through a cooling tower to maintain to optimal charging temperature. Previous analysis of the charging process for Inbatec Units 1 and 2 show the cooling tower have the capacity to quickly remove the excess heat in the sulfuric …

Investigating The Effect Of Hydrophilic Block Length On The Co-Assembly Behavior Of Amphiphilic Triblock Copolymers, Alexandra M. Garrett

Honors Theses

Polymer vesicles and micelles have been of interest in the scientific community for the past few decades due to potential biomedical applications in areas such as drug delivery, nanoreactors, and biosensing. Polymer vesicles and micelles are formed through the self-assembly of amphiphilic block copolymers. The objective of this project is to gain a better understanding of the influence of hydrophilic block copolymer length and composition in controlling the resulting morphologies from the co-assembly of triblock copolymers. First, a hydrophobic block composed of poly(methyl acrylate) was synthesized using reversible addition-fragmentation chain-transfer (RAFT) polymerization mediated by a difunctional chain-transfer agent. The block …

Co-Assembly Behavior Of Neutral And Zwitterionic Amphiphilic Block Copolymers In The Fabrication Of Glassy Polymer Vesicles, Elina Ghimire

Honors Theses

Polymersomes, also known as polymer vesicles, are hollow capsules fabricated through the solution assembly of amphiphilic block copolymers. Polymer vesicles have garnered a great deal of interest in materials science because of their potential application in areas such as drug delivery, diagnostics and imaging, gene therapy, and as nanoreactors. The goal of this project is to understand the factors that affect the arrangement of triblocks in vesicle membrane via the study of the co-assembly behavior of linear amphiphilic triblocks with different hydrophilic blocks. We investigated the self- and co-assembly behavior of amphiphilic triblock copolymers with neutral hydrophilic blocks. Moreover, we …

Tailoring Photodegradation Rates Of Acetal-Containing Polymer Networks, Michael Sandoz

Honors Theses

In this thesis, we explore the degradation of poly (thioether acetal) thermosets via a photoinduced thiol-catalyzed ß-scission of acetal linkages incorporated as network crosslink junctions. Specifically, a library of bis-allyl acetal-containing monomers derived from para-substituted benzaldehydes was synthesized and formulated into photopolymerizable thiol-ene resins with commercially available thiol monomers. By varying the electron donating or withdrawing nature of the monomer substituent, we explored the impact of substituent effects on the rate of polymer degradation. Furthermore, we compare the results to those expected from a classical Hammett-type relationship of substituent electronic effects. FTIR was employed to track the appearance of the …

Aircraft Rescue And Fire Fighting Capabilities: Are Today’S Standards Protecting Passenger’S Futures?, Kaetlyn Blocker

Student Works

Few studies have been conducted that have truly considered the relevance and inadequacies of applicable aircraft rescue and firefighting (ARFF) regulations. Fewer still have studied and explored accident cases that directly exemplify the deficiencies and inconsistencies of various regulatory standards and requirements. This study seeks to expose and explain those inadequacies by utilizing a historical, case-study type research method to examine accident cases during which time the governing regulations played a significant role in the ARFF operations. The findings discovered as a result of this multi-case analysis provide evidence that the current regulations governing United States ARFF operations are both …

Impact Of Part Thickness And Drying Conditions On Saturation Limits In Binder Jet Additive Manufacturing, Nathan B. Crane

Faculty Publications

Binder jetting (BJ) is a high build-rate additive manufacturing process with growing commercial interest. Growth in BJ applications is driven by the use of finer powders and improved post-processing methods that can produce dense, homogenous final parts. However, understanding of the basic droplet/powder interaction is relatively limited. This paper considers the impact of in-process drying, part geometry, and droplet size on a key printing parameter: binder saturation. Parts of varying thicknesses are printed with a range of saturation levels under various heating conditions. The ratio of the printed part mass to the theoretical part mass is used to detect bleeding. …

Partial Discharge Classification For Xlpe Cable Joints Using K Nearest Neighbors Algorithm, Mohd Salleh Muhammad Shairazi

Student Works (2020-2029)

Due to excellent mechanical and electrical properties, cross-linked polyethylene (XLPE) cables are commonly used in the power industry. However, cable joints are the weakest part of XLPE cables and are susceptible to insulation failures. Cable joint insulation breakup can cause large losses for power companies. It is therefore necessary to evaluate the consistency of the insulation for early detection of insulation failure. It is known that there is a link between the partial discharge (PD) and the quality of the insulation. PD analysis is an important tool for assessing the quality of insulation in cable joints. In this study, XLPE …

Re-Evaluating Coverage Metrics For Wireless Sensor Network Border Security Applications, Kevin Haney

Industrial Engineering Undergraduate Honors Theses

Wireless sensor networks are an emerging technology used to monitor an environment over time. One specific application of the wireless sensor network is the border security application. Researchers have adapted coverage metrics from general wireless sensor network literature to fit the border security application. While some of the adapted metrics count the number of sensors detecting a potential target, others measure the distance between a potential target and its nearest sensor. No existing metric accounts for both of these factors. To take advantage of this gap and to attempt to increase the accuracy to which coverage is measured in this …

Promoting The Sustainable Utilization Of Groundwater Resources In Ethiopia Using The Integrated Groundwater Footprint Index, Xinyu Lin

Honors Scholar Theses

The country of Ethiopia is highly vulnerable to human-caused climate change and is already suffering from the effects. The predominately rural population relies heavily on small-scale agriculture, with 78% of households having at least one member engaged in the field, yet staple crops are highly susceptible to droughts and other weather shocks. Total and agricultural GDP growth in the country have been strongly linked to inter-annual rainfall variability, of which Ethiopia has among the highest in sub-Saharan Africa. A decrease in rainfall since the 1970s has been one of the primary causes of low crop yields, and stresses the immediate …

Melamine-Derived Graphene Foam As A Thermal Additive For Water Harvesting Applications, Emily Chase

Honors Theses

This project proposes the use of a novel melamine-derived graphene foam formed by high temperature pyrolysis under inert conditions for use as a thermal additive to absorbent crystals. The high thermal conductivity of graphene foam makes it an ideal candidate for use as a cheap, flexible, and light-weight alternative to previously used copper foam and metal organic frameworks. Following surface functionalization, graphene foam may be saturated with hydrophilic absorbent crystals. The primary objectives of this research are to optimize the synthesis process of such a graphene foam to obtain the highest purity product while maintaining foam flexibility and to study …

Synthesizing And Modeling The Optical Properties Of Silica Aerogel, Hannah Margavio

Honors Theses

Silica aerogel has attracted the attention of researchers for decades for its applications in insulation materials, storage, and solar-thermal devices. The appeal surrounding silica aerogel is attributed to its unique combination of physical and chemical properties. Silica aerogel is a highly porous, optically transparent nano-polymer with a low thermal conductivity. Additionally, the material boasts a super-low density, high specific surface area, and low dielectric constant. The following report proposes a viable method of synthesizing polyvinylpolymethylsilane (PVPMS) aerogel as well as a model for determining the optical performance of TMOS aerogel by determining its radiative properties. First, the report will explore …

The Problem-Solving Workshop: Adapting Process Improvement Methodologies For K-12 Educators, Madison Chan

Honors Theses

Lean and Six Sigma have been lauded in the manufacturing sector for their ability to streamline processes, reduce waste, minimize variation and defects, and improve the bottom line. Although these methodologies have begun to spread to other industries, their impact has been relegated to certain areas and has largely missed others. One area that bears strong consideration is education. Education is heavily process-based and notoriously tight on resources. It is hypothesized that if educators were taught the basics of these strategies and were able to implement them in the classroom setting, the effectiveness of both teaching strategies and classroom operations …

An Investigation Of Diode Failure, Nicholas James Adams

Physics

Solar electricity can be used to cheaply cook food and charge electronic devices. We investigate the viability of using diodes as heating elements for insulated solar electric cooking (ISEC). In addition, information on designing and constructing ISEC compatible phone chargers and rechargeable LED lighting systems is included.

Nitrate And Herbicides Removal From Groundwater Using Immobilized Algae, Sara Mollamohammada

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

To improve crop yield and control broadleaf weeds, many farmers apply nitrate-based fertilizers and chemical herbicides to their fields. Excessive use of these chemicals can cause contamination in waterbodies and impact on the public health. The physical and chemical methods have been suggested to remove these herbicides are usually costly. In this study, the capability of immobilized algal beads in removing nitrate and several herbicides of environmental concern from synthetic and actual groundwater and surface water was evaluated.

The experiments were performed in batch, sequencing batch and continuous flow modes and the effect of different operational conditions (light intensity, cultivation …

Micro Distillery Process Design And Business Plan, Nolan Hughes

Graduate Theses - Engineering Management

This integrated project investigates entry into the growing distillery market. The specific entry point will be a craft distillery focusing on the artisanal production of rum in Houston, Texas and the surrounding regions. A flexible design of a distillation process implementing a hybrid pot still with a total capital investment of $391,000 was generated. A business model incorporating this process design develops the consumer basis, value proposition, key activities, and cost structure of the artisanal distillery. Following the proposed business model incorporating the maximization of initial cash flow, the resulting NPV at a discount rate of 10% after 10 years …

Wait A Minute! Reducing Campus Eatery Wait Times, Yewande Ade-Arigbabuwo

Graduate Theses - Engineering Management

The purpose of this study was to reduce meal wait times at Chauncey’s, a pub-style eatery for students at Rose-Hulman Institute of Technology. Chauncey’s re-opened in Fall 2018-19 after the student union was redesigned in Summer 2018. With its refreshed look and menu, its popularity grew, and so did its customers’ wait times. Despite Chauncey’s staffs’ efforts to reduce wait times in the fall and winter quarters, the waits still fluctuated at peak times and were often longer than customers considered reasonable. Consequently, dissatisfied customers sometimes gravitated towards other campus dining options, such as the student cafeteria. Not only does …

Pollution Prevention Via Recovery Of Cerium (Iv) Oxide In Optics Company, Eugene Park, William Gallagher, Sydor Optics, Flint Creek Resources

Articles

Pollution prevention methods were applied at an optics manufacturer in an effort to improve recovery of a valuable polishing component, cerium oxide (ceria), 77% of which was lost to dragout and sewer discharge. Centrifugation and microfiltratiion were evaluated to develop a process that would increase recovery of used ceria, which would then be sent back to the ceria supplier for reclamation and reuse. Full-scale implementation included a high-speed centrifuge that operates continuously with a microfiltration system through recirculation in a single process tank. Sydor Optics has improved ceria recovery from 23% to 48%, saving thousands of dollars annually.

Mechanical Analysis Of Double Network Hydrogels To Determine Suitability As An Articular Cartilage Substitute, Casey Virginia Young

All Theses

The Center for Disease Control has found that between 2013-2015, 26% of women and 19% of men reported doctor-diagnosed cartilage disease or damage. Currently, there exists a substantial population with cartilage damage or disease needing a solution to increasing pain and decreasing function and mobility. Many of these individuals are young and thus looking for a treatment to delay a total knee replacement. Many others are elderly and thus looking to avoid major surgeries, as the riskiness of these procedures increases with age. As researchers look towards a method of cartilage replacement, hydrogels show measurable potential as a synthetic substitute …

Characterization Of Mechanical, Thermodynamic And Surface Properties Of The Butterfly Proboscis, Tatiana Stepanova

All Theses

The butterfly proboscis is a fascinating fiber designed to probe and transport fluids. The built-in sensors and actuators make this fiber multifunctional. The proboscis consists of 2 hollow C-shaped tubes that are united when the butterfly comes out of the pupa. A single galea consists of a solid cuticular wall, muscles, nerves, and tracheae. The proboscis cuticular wall is mainly composed of polymers and small amounts of metals and non-metals. The proboscis is a porous material, and its water content is high, up to 50%. When the butterfly is not hungry, its proboscis is tightly coiled; when the butterfly is …

Static Pressure Recovery Effects Of Conical Diffusers With Swirling Inlet Flow, James Ray Wright Iii

All Theses

Conical diffusers are used in hundreds of engineering applications in various industries. Some of the operating conditions that they operate under cause swirling flow to enter the diffuser. It is generally well documented that the addition of swirl to the flow of a diffuser allows for greater divergence angles without wall separation, resulting in better overall performance of the diffuser and the machine it’s attached to. It is also known that as swirl strength is increased, the flow will eventually breakdown, resulting in internal flow recirculation and decreased diffuser performance. However, the relationship between the diffuser geometry and its performance …

Impact Of Compactive Effort On Soil Strength Of Glacial Lake Columbia Soils, Alexander M. Navarra, Dwight Hendrickson, Jaremy Shaw

2020 Symposium Posters

Glacial Lake Columbia (GLC) existed from 15,550 (+/- 450) to 13,050 (+/- 650) years ago (Atwater, 1986) as a result of the Okanagan Lobe of the Cordilleran Ice Sheet damming the Columbia River near present-day Grand Coulee Dam. The lake deposited a fine-grained basal layer that had interbeds of coarse Missoula Flood deposits and later lake deposits above. Because these GLC deposits are present around most of the Spokane area, they are important to civil engineering and development. We sampled the basal layer of GLC soils from the Peone Prairie, WA. We performed prerequisite testing before the main experiment, with …

Additive Manufacturing And How 3d Printing Is Fighting Covid-19, Raghavan Srinivasan, Ahsan Mian, Joy Gockel, Laura M. Luehrmann

Mechanical and Materials Engineering Faculty Publications

This is the fourth installment in the Shelter in Place (SiP) Lecture series. This installment covers the creative ways that 3D printing has supported efforts to combat the pandemic. It covers the basics of what 3D printing is, some of the various creative projects that have used 3D printing to combat the pandemic, among other topics and questions by the pandemic.

Passive And Active Battery Balancing Methods Implemented On Second Use Lithium-Ion Batteries, Walter Bartek

Masters Theses

As the number of electric vehicles (EVs) increases, the number of used battery packs that require disposal increases; however, many of these packs still have useful capacity and can be repurposed. When using repurposed large lithium-ion battery packs, deviations between cells within a pack become problematic. These deviations result in a pack that is unbalanced, affecting performance and proving potentially hazardous when charging. Consequently, a battery management system (BMS) is needed. To provide safety, the BMS in this paper monitors and controls the operation of the battery pack. In addition, it controls the redistribution of charge between the cells within …

Elucidating Basis Of Rice Discoloration And Developing Prevention Strategies, Zeinab Mohammadi Shad

Graduate Theses and Dissertations

Economically, discolored rice kernels have less market value, which can seriously impact farm net profit. The reasons for rice discoloration during storage have not been studied extensively and many questions remain. Therefore, the primary goal of this study was to improve understanding of the role and contributions of storage practices on rice quality degradation and discoloration. In this study, three rice cultivars including XL753 (hybrid), Roy J (pureline), and Titan were assessed for changes in quality and microbial kinetics. The rice samples at a high moisture content (MC) of 21% w.b. and a low MC of 16% were stored at …