Engineering Commons^™

Analysis And Optimization Of Colorimetric Nanosensors For Rapid Detection Of Microbes In Water, Ruby A. Lang

Master's Theses

Access to safe water is a basic human right recognized by the United Nations General Assembly in 2010 (WHO, 2020). However, a least 2.2 billion people globally still are without safely managed water services meaning they use a drinking water source that can be contaminated with faeces (WHO, 2020). With such a pressing global health issue, it is clear that improvement to water systems is important and required in the Agenda 2030 Sustainable Development Goals (SDGs). However, to improve water systems and prove they are safe water sources, water quality testing must occur. A solution to this issue is the …

Pier Portal, Alec W. Hardy

Master's Theses

The Pier Portal marine monitoring system is an internet controlled underwater camera that will enable students, researchers, and the general public the ability to monitor underwater marine life and ocean conditions. Installed at Cal Poly’s Center for Coastal Marine Science pier at Avila Beach, California, the camera can be commanded in real-time to raise or lower to any position between the top of the pier and the bottom of the ocean floor, while providing a live-stream video to the operator and general public. This thesis effort focused on the integration of the various subsystem components through software, and the development …

Closing The Data-Decisions Loop: Deploying Artificial Intelligence For Dynamic Resource Management, Pradeep Varakantham

Asian Management Insights

Improving predictions and allocations to determine the optimal matching of demand and supply in a dynamic, uncertain future.

The Effect Of Climate Change On Groundwater Recharge In The United Arab Emirates, Yuliya Fadlallah Saade

Civil and Environmental Theses

Climate change is impacting ecosystems and the water resources by causing temperature variation. Evapotranspiration rates are increasing when the temperature is high whereas, precipitation amount and intensity are varying based on geographical locations.

This change in precipitation has an inevitable impact on the groundwater recharge. Quantification of groundwater recharge is a prerequisite for efficient and sustainable groundwater resources management in arid regions.

Although, both surface and groundwater resources in the United Arab Emirates (UAE) are scarce; the anticipated climate change impacts could make these resources even scarcer. As such, the main aim of this thesis is to assess the potential …

Surface Autonomous Vehicle For Emergency Rescue, Max Emerick, Ryan Shields, Christopher Feickert, Raymond Impara

Mechanical Engineering

The goal of this document is to clearly define the problem parameters and project objectives and to clearly describe the design process, planned final design, and manufacturing and testing procedures for the senior design project of Team 26: SAVER -- the Surface Autonomous Vehicle for Emergency Rescue. This is both for the purpose of project planning and for clear communication between all parties involved in the project.

The objective of the SAVER project is to develop a proof of concept for an autonomous maritime search and rescue vehicle for aiding in man-overboard missions. To accomplish this goal, a list of …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Wine History Project Pavilion, Douglas Mcarthur

Architectural Engineering

The Wine History Pavilion Project is a continuing endeavor of Cal Poly students working on an exhibitive, traveling structure for the San Luis Obispo community. The project started during the 2019 Fall Quarter in the interdisciplinary Integrated Project Delivery (IPD) Studio and has progressed to the detailed design stage for its eventual fabrication and installation. This report discusses the detailed design stage that 4th year Architectural Engineering student, Douglas McArthur, worked on.

The Aloe: High Rise Schematic Design And Analysis, Tony Duc Nguyen, Lilliann Lan Lai

Architectural Engineering

The authors of this document are architectural engineering (ARCE) undergraduate students from California Polytechnic State University, San Luis Obispo (Cal Poly). They joined the 2020 Skyscraper Collaboratory as part of the ARCE course 415: Interdisciplinary Capstone Project. This course emphasizes the analysis and evaluation of interdisciplinary challenges associated with integrating the design and construction processes to deliver a project with respect to the design, quality, and performance expectations for a client or presented criteria. The course was taught in collaboration with industry partners and associates from the global architectural, urban planning, and engineering firm Skidmore, Owings & Merrill (SOM). Instruction …

Piazza Di Ulivo: Arce Patio Redesign, Sophia Kim-Oanh Ha, David Colman

Architectural Engineering

Piazza de Ulivo was Phase 1 of a multi-quarter initiative to redesign and bring life to a patio space adjacent to Engineering West (Building 21) in Spring of 2020. Located within the central courtyard of Engineering West (Hasslein Garden), the patio space previously contained a senior project pergola that collapsed and has been removed. The remaining elements from this previous structure were an inverted moment frame consisting of five concrete columns and beams joining them. Additionally, a wooden bench with concrete pedestals remained under the shade of the existing olive tree. Desire within the Architectural Engineering (ARCE) department for the …

Evidence From Urban Roads Without Bicycle Lanes On The Impact Of Bicycle Traffic On Passenger Car Travel Speeds, Jaclyn S. Schaefer, Miguel A. Figliozzi, Avinash Unnikrishnan

Civil and Environmental Engineering Faculty Publications and Presentations

A concern raised by some motorists in relation to the presence of bicycles on urban roads without bicycle lanes, discussed in part of the traffic literature, is that cyclists will slow down motorized vehicles and therefore create congestion. This research answers this question: do bicycles reduce passenger car travel speeds on urban roads without bicycle lanes? To answer this question, a detailed comparative analysis of the travel speeds of passenger car (class two vehicles) on lower volume urban roads without bicycle lanes is presented. Speed distributions, the mean, and the 50th and 85th percentile speeds for two scenarios were examined: …

Concussion Detection Device, Jenna C. Sussex, Mark B. Edin, Bianca X. Aleman

Biomedical Engineering

No abstract provided.

D.I.Y. Clean Hood, Samuel G. Porter, Ryan E. Shimogaki, Ryan S. Staples

Biomedical Engineering

The DIY Clean Hood is a low-cost, sterile, and accessible scientific workspace intended for installation in the BioElectroFluidics Lab of California Polytechnic State University’s (San Luis Obispo) Biomedical Engineering Department (BMED), under the sponsorship of Dr. Benjamin Hawkins, PhD. As normal Clean Hood, Biosafety Cabinets, and the like are generally too expensive for a university, a competitive solution to an expensive problem can assist research students and professors alike continue their own work with an inexpensive yet effective environment.

Specific design elements that the customer requirements entailed for the project include a low-particle-count air filtration system, positive pressure air flow …

Sandy Feet, Garrett E. Herbst, Jacqueline Chuang, Jerin T. Brust, Parker S. Duncan

General Engineering

Sgt. Brady is a former armed forces member with a transtibial amputation. He walks on sand frequently for work and leisure, but experiences severe pain and inconvenience because his current prosthesis is not meant for use on sand. Sand Foot V2 is a prosthesis that allows Sgt. Brady to walk on sand for long periods of time without issue.

Mountain Arm, Conner Magnuson, Amanda Lingle, Jordan Ambrose, Marco Lopez

General Engineering

QL+ Challenger, US Navy Veteran, and transhumeral amputee Cassie Perando needed a way to backpack comfortably and independently while wearing a transhumeral prosthesis, as this is something that she enjoys doing often. The current prosthesis she wears causes pinching while wearing a backpack. To eliminate this issue, we decided to design and create a dynamic, pin-lock socket. This design decision allowed for a comfortable fit for Cassie that will not interfere with the backpack straps. As a secondary suspension system, we designed a sports bra with straps that attach to her opposing side and connect to the front and the …

Effects Of Ring Rolling On Grain Size In Inconel 718 And Waspaloy, David Webster

Materials Engineering

Carlton Forge Works, an industry leader in the manufacture of rolled rings, has observed anomalous grain structures in parts made from Inconel 718 and Waspaloy. These take the form of unusually large grains at the surface of the rings, causing them to fail industry grain size standards. Grain size testing is a critical part of evaluating parts before they are used as grain size and structure control many mechanical properties including creep resistance, low and high cycle fatigue life, and yield strength. These unusually large grains are only present within the first tenth of an inch of the surface of …

Microstructure And Tensile Properties Of Close-Die Forged Ti-6al-4v Aircraft Engine Mount, Renee Roeder, Nick Chen, Michael Viksne

Materials Engineering

The microstructural characteristics of a Ti-6Al-4V close-die forging that passes yield strength specifications are examined and found to be consistent with literature recommendations. Originally, the intent was to compare the microstructure of a forging that passed specification to the microstructure of a forging that did not pass specifications using the imaging software ImageJ. Due to time and safety constraints considering the COVID-19 pandemic, the data that is presented is incomplete data on only the forging that passes specifications. There are no comparisons between the forging that did not pass and the forging that passed.

Autonomous Butter Robot, David Chau, Michael Hegglin

Computer Engineering

Don’t you wish your butter would come to you? Well now it can with the patented Michael and David butter robot! Based on an idea from a TV show, our team set out to see if a similar robot was possible to make in real life. The objective was simple. Can we make a small table sized robot that can bring a person butter using image detection software? With that question in mind we set out buying our components. We wanted to keep it small, so we looked up devices that could do simple image processing and from there we …

Non-Toxic Soil Thickeners For Reducing Mudslide Intensity, Mitchell William Jensen

Materials Engineering

This project was intended to be a continuation of senior project work done last year by a group consisting of two Materials Engineering students and a Soil Science student. Their report was crucial in identifying a range of food thickeners that could be capable of performing in the mud thickening application. All thickeners that were chosen both this year and last year are biocompatible, to alleviate some toxicity concerns. The food thickeners all belong to a class of compounds known as colloids. Since water is the fluid being thickened, these compounds are more accurately referred to as hydrocolloids. Hydrocolloids are …

Pitting Corrosion Of Oerlikon’S Abrasion Resistant Ferritic Stainless Steels, Matthew P. Nalty, Emma Wagstaff

Materials Engineering

Existing hardfacing coatings for hydraulic cylinders and brake disc applications crack during use leaving the components susceptible to corrosion. To address this problem, Oerlikon has designed three new alloys to be abrasion and corrosion resistant. This paper reviews the literature necessary to understand and quantify pitting resistance of stainless-steel alloys. It documents one round of testing ASTM G48 method A: Ferric Chloride Pitting Test of Stainless Steels on the new alloys P72-X9, P72-X13, P129-X9, as well as samples of 431, 316, and 2205 stainless steels. This paper also discusses improvements to the G48 testing method and industry use of the …

Investigation Of Ceramic Firing Processes For Investment Casting Shell Molds, Leonardo Ken Hoaakua Nakamura, Rileigh Anne Cotter

Materials Engineering

PCC Structurals aims to improve the quality and consistency of their ceramic mold production for their investment casting processes to decrease product loss figures. Although their current production processes result in acceptable quantities of high-quality molds, a significant percentage of defective molds are produced. These defective molds cause appreciable product loss due to casting defects and mold failure. Available literature dictates that high-quality investment casting molds must exhibit fracture strengths within a desired range in order to perform adequately. However, information regarding specific firing procedures which consistently result in ceramic mold strengths within this range is not readily available. To …

Alternative To Custom 450© Stainless Steel For Use In Investment Cast Golf Club Heads, William Henry Armstrong Iv, Davis Martin Loen

Materials Engineering

This investigation seeks to improve on the mechanical property of yield strength, while maintaining 10% elongation prior to fracture observed with of Custom 450 stainless steel in an air-melted investment casting operation. Improving this performance includes an additional heat treatment step of homogenization, as well as replacing the alloy. After identifying and downselecting available high strength stainless steels, a trial of Custom 455 stainless steel is recommended due to its high strength compared to the other alternative alloys. A trial has been developed to analyze the effect air melting has on the chemical composition and mechanical properties of Custom 455 …

Failure Analysis Of Investment Cast Near-Alpha Titanium Alloys, Garrett Ryan Bader, Jonathan Anton Linquist

Materials Engineering

In this project, fracture surfaces of three titanium investment castings were studied as part of a failure analysis on a TaylorMade metalwood. The crack formation occurred between investment cast Ti 9-1-1 and rolled Ti 6-4 joined by laser beam welding. The microstructure of the Ti 9-1-1 contained alpha colonies in large prior beta grains, while the Ti 6-4 was primarily Widmanstätten in basket weave morphology, refined with subsequent rolling. Over a period of cyclic loading, cracking occurred at the face-sole transition in the metalwoods that had been cast from a certain supplier B, while metalwoods that had undergone similar treatment …

Insulated Solar Electric Cooker, Paige Camacho, Ahmed Gouda, Caroline Hodes, Wyatt Johnson

General Engineering

The purpose of this Final Project Report is to highlight the work completed by the interdisciplinary engineering capstone project for the Insulated Solar Electric Cooker (ISEC) at California Polytechnic State University, San Luis Obispo under the supervision of Professor Jim Widmann (Mechanical Engineering) and Dr. Peter Schwartz (Physics). Dr. Schwartz, better known as Pete, has been working on the project with a team of students for the past five years and is working to integrate the ISEC in Ghanaian communities. This project focuses on making the ISEC mass-manufacturable and making the transition from biomass cooking to solar cooking as familiar …

Effects Of Surface Finish On High Cycle Fatigue Of Inconel 718, Jessica A. Mcroskey, Matthew Busse

Materials Engineering

Inconel 718 is a nickel-based superalloy and commonly used rocket engine material due to its excellent properties at elevated temperatures. Its fatigue life relies heavily on the surface roughness, as fatigue introduces and propagates cracks at the surface. Part standards set by Aerojet Rocketdyne typically necessitate surface roughness values from 64 to 125 Ra. However, surface topography and residual stresses incurred from the finishing process also affect the fatigue performance. The specific goal of the project is to perform a literature review and write experimental methods to determine how the surface roughness, topography, and residual stresses from turning, grit blasting, …

The Influence Of Time And Temperature On 7781 Prepreg Outside Storage, Matthew L. Fuentez, Edwin Stuart Ross Viii

Materials Engineering

Investigation into the issue of out of specification flow data revealed that unregulated transportation conditions exposed 7781 prepreg with phenolic resin to temperature fluctuations up to 125°F. The temperature fluctuations have the potential to advance unwanted curing in the prepreg, making it unsuitable for manufacturing. However, this explanation does not account for the prepreg exceeding specifications above the upper limit. Another explanation was investigated that involved exposure to moisture. Moisture could be preventing curing from taking place and thus resulting in higher flow values. Data collection was unable to proceed past the preliminary stages due to the COVID-19 pandemic and …

Study Of Permeability Testing Methods For Composite Laminates, Thomas S. Busse, Giannina Marie M. Yu

Materials Engineering

Permeability measurements are strong indicators of the effectiveness of evacuation channels within a composite prepreg. The effectiveness of these evacuation channels directly relates to the void content within a processed composite laminate. The goal of Toray Advanced Composites was to compare two permeability tests and determine which one was more reliable, accurate, and economical. The first permeability test method was the Cirrus method, designed by Cirrus Aircraft, a customer of Toray Advanced Composites. The second test was ASTM D8132, the standard method for permeability testing. Additionally, Toray sought to investigate the effect out-time had on the permeability of three different …

Mechani-Kits Senior Design Project, Jake Utley, Sophie Carson, Vincent Seguin

Mechanical Engineering

Studies suggest that when designed and executed well, hands-on activities can enhance student understanding of key mechanics concepts. Current products are expensive and typically not designed to meet a variety of learning objectives. Through the Mechanics of Inclusion and Inclusivity in Mechanics grant, the Cal Poly Physics and Engineering Departments are seeking to incorporate new hands-on activities into their courses. Our team has designed three inexpensive ”MechaniKits” to be used in physics, statics and dynamics courses [1]. This Final Design Review outlines our findings, objectives, and final designs for this project. It also explains our manufacturing and design verification plans. …

Design And Implementation Of Spatial Augmented Reality In Large Scene, Shuiying Ge, Shuman Liu, Shibiao Xu, Xiaopeng Zhang

Journal of System Simulation

Abstract: To get long distance marker recognition in Augmented Reality, three software development toolkits were used to construct the long distance marker-less registration technology based on depth sensor, and develop a new augmented reality system based on PC platform. The tracking system was constructed by Kinect and camera. Defects in the single camera tracking system for long distance tracking were improved, and human-computer interaction in Augmented Reality was realized. By the detailed description of the main function modules, such as position calibration module, maker-less virtual-real registration module, and natural interaction module, the system design concept was introduced. Experiment results show …

Solving Flexible Job-Shop Scheduling Problem By Improved Chicken Swarm Optimization Algorithm, Shipeng Xu, Dinghui Wu, Kong Fei, Zhicheng Ji

Journal of System Simulation

Abstract: To solve the flexible job-shop scheduling problem (FJSP) more effectively, an improved chicken swarm optimization (ICSO) algorithm was proposed. A flexible job-shop scheduling model was established for the purpose of minimizing the machine makespan. The improved chicken swarm optimization algorithm was presented. Algorithm improved the update formula of chicks and combined the advantages of simulated annealing algorithm and dynamic inertia cosine weight strategy, which achieved an effective balance of global search and local exploration. According to simulating and testing four standard functions and a flexible job shop scheduling model and compared with particle swarm optimization (PSO) and chicken swarm …

Study On Balanced Energy-Consumption Routing Protocol Of Airfield Single-Lamp Monitoring System, Gao Mei, Bingyuan Wang, Dandan Zhang, Zhaorong Sun

Journal of System Simulation

Abstract: To extend the sensor node lifetime and balance the energy consumption of the wireless sensor network, on the basis of the protocols AL-CAME (Airfield lighting-clustering algorithm based on max energy) and ECOMP (Efficient cluster-based communication protocol), a clustered hierarchy protocol of balanced energy-consumption was proposed for the airfield single-lamp monitoring system. According to the protocol, every two sensor nodes formed a cluster, and the node with the highest remaining energy was elected to be cluster head which was responsible for data aggregation within the cluster. The balanced routing algorithm was adopted in data-transmission from cluster head to …