Engineering Commons^™

Targeted Processing Method For Seismic Data Of Karst Caves And Goafs In Nanchuan Area, Meng Qingli, Ren Junxing, Yang Fan

Coal Geology & Exploration

In order to solve the problem of poor imaging effect of near surface karst cave and goaf location seismic data in seismic exploration, this paper summarizes the frequency, energy and signal-to-noise ratio characteristics of seismic data in this area using forward modeling combined with actual data analysis. On this basis, a set of corresponding processing methods are proposed, including micro log constrained tomography static correction, weak signal extraction and compensation, pre-stack five dimensional data regularization and structure constrained grid tomography velocity modeling. Through the application in Nanchuan area, the signal-to-noise ratio and wave group continuity of seismic data are obviously …

The Application Of Opposing Coils Transient Electromagnetics In The Detection Of Karst Subsidence Area, Xie Jia, Liu Yang, Li Xingqiang, Lu Yulong, Li Ganlong

Coal Geology & Exploration

Ground collapse caused by karst is both disastrous and covert. In order to forecast and control it effectively, a research area with strong karst collapse development was selected in this study, and a method that combines Opposing Coils Transient Electromagnetics with engineering geological drilling was used to verify the formation occurrence through the factors including buried depth of overburden, resistivity and isoline variation. The results of geophysical inversion maps and borehole information verification show that the Opposing Coils Transient Electromagnetics method can effectively identify the development of underground corrosion. Especially in the area where the conventional geophysical exploration methods may …

Borehole-Roadway Seismic-While-Mining Tomography Using Correlation Time Difference, Wang Yunhong, Wang Baoli, Cheng Jianyuan, Cui Weixiong, Jin Dan

Coal Geology & Exploration

Using shearer as a source, seismic-while-mining(SWM) technology has realized dynamic, accurate and green intelligent detection in fully mechanized mining faces, and can be used to detect static geological anomaly and dynamic mining geological disasters within the work face. Conventional SWM observation system has the defect of blind area. To solve this problem, a new observation system with detectors installed in both roadway and within boreholes are proposed, which effectively improved the imaging range. Based on seismic interferometry principle, using frequency domain correlation algorithm, this paper turns the SWM signal to explosive source signal, and computes the equivalent shot sets. In …

The Application Of Pneumatic Directional Drilling Technology In Gas Pre-Drainage Of Strips In Soft Coal Seams, Zhang Jie

Coal Geology & Exploration

It is costly and inefficient to drill through floor tunnel to eliminate outburst in soft coal roadway strip in Huaibei Mining Area. The bedding pneumatic directional borehole technology can accurately control the borehole trajectory in the strip coal seam according to the design, and realize the outburst elimination of the strip coal roadway through drilling gas extraction. Based on soft coal seam characteristics of the Huaibei Mining Area, the coal lane stripes drainage of gas in the directional hole design, selection of pneumatic directional drilling equipment, directional bore blastholes and shield technology, the evaluation of extraction effect are studied. The …

Robotic Technologies For High-Throughput Plant Phenotyping: Contemporary Reviews And Future Perspectives, Abbas Atefi, Yufeng Ge, Santosh Pitla, James Schnable

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Phenotyping plants is an essential component of any effort to develop new crop varieties. As plant breeders seek to increase crop productivity and produce more food for the future, the amount of phenotype information they require will also increase. Traditional plant phenotyping relying on manual measurement is laborious, time-consuming, error-prone, and costly. Plant phenotyping robots have emerged as a high-throughput technology to measure morphological, chemical and physiological properties of large number of plants. Several robotic systems have been developed to fulfill different phenotyping missions. In particular, robotic phenotyping has the potential to enable efficient monitoring of changes in plant traits …

Comparison Of Promoter, Dna Vector, And Cationic Carrier For Efficient Transfection Of Hmscs From Multiple Donors And Tissue Sources, Tyler Kozisek, Andrew Hamann, Luke Samuelson, Miguel Fudolig, Angela K. Pannier

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Human mesenchymal stem cells (hMSCs) are primary cells with high clinical relevance that could be enhanced through genetic modification. However, gene delivery, particularly through nonviral routes, is inefficient. To address the shortcomings of nonviral gene delivery to hMSCs, our lab has previously demonstrated that pharmacological “priming” of hMSCs with clinically approved drugs can increase transfection in hMSCs by modulating transfection-induced cytotoxicity. However, even with priming, hMSC transfection remains inefficient for clinical applications. This work takes a complementary approach to addressing the challenges of transfecting hMSCs by systematically investigating key transfection parameters for their effect on transgene expression. Specifically, we investigated …

A Kinematic Error Controller For Real-Time Kinematic Error Correction Of Industrial Robots, Mitchell R. Woodside, Joseph Fischer, Patrick Bazzoli, Douglas A. Bristow, Robert G. Landers

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Industrial robots are being used more and more for manufacturing applications that require accuracy beyond what can be obtained from joint measurement. While offline calibration techniques such as volumetric error compensation can be used to correct robot kinematic error, these methods are unable to compensate for robot deformations caused by changing tool loads during the manufacturing operation. This paper explores the use of a real-time robot kinematic error compensation technique where an external high-precision feedback sensor (in this case a laser tracker) directly measures the robot kinematic error and corrections are implemented during processing. A robot kinematic error model is …

Influence Of Coating Defects Within The Lock Seams On The Corrosion Performance Of Aluminized Steel Drainage Pipes, Mohammed Al Yaarubi

USF Tampa Graduate Theses and Dissertations

The electrochemical behavior of aluminized steel is investigated to determine the corrosion performance of coating deficiencies generated within the lock seams during the fabrication of aluminized steel corrugated pipe. Electrochemical techniques and visual and profilometric analysis are used to assess the ability of the aluminum and zinc coating to provide sufficient galvanic protection to the underlying steel in the presence of a crevice. Also, Crevice coupons and lock-seam samples were used in this investigation in different environmental conditions simulating natural water conditions to relate the corrosion rate with the level of protection that the coating will provide. In addition, a …

Development Of A Numerical Process Model For Adsorbent-Amended Constructed Wetlands, Lillian Mulligan

USF Tampa Graduate Theses and Dissertations

There is a need for alternative methods for municipal landfill leachate treatment as the high concentrations of pollutants in leachate interfere with processes at publicly owned treatment works (POTWs). Constructed wetlands (CWs) have been shown to be a sustainable alternative with good removal efficiencies for chemical oxygen demand (COD) and ammonia nitrogen (NH4+). The addition of an adsorbent media, such as zeolite and biochar, to CWs to further enhance removal efficiencies has been investigated in recent years. However, the long-term effects of zeolite and biochar addition to CWs is not well known. A model could be a useful tool to …

Flow Visualization And Aerosol Characterization Of Respiratory Jets Exhaled From A Mannequin Simulator, Sindhu Reddy Mutra

USF Tampa Graduate Theses and Dissertations

It is important to understand the airborne transmission of infectious diseases due to the COVID-19 pandemic. Physical experiments were conducted to understand the dispersion of aerosols emitted from a mannequin simulator replicating human tidal breathing through the nose and mouth with and without a protective face mask in an enclosed space. Flow patterns are observed via high-speed visualization, and the concentration and size distribution of the particles is measured as a function of distance from the mannequin using an optical particle sizer. Masks were shown to effectively reduce the horizontal dispersion of aerosol for both mouth and nose breathing. Further, …

Corrosion Propagation Of Stainless Steel Reinforced Concrete, Nelly Sofía Orozco Martínez

USF Tampa Graduate Theses and Dissertations

Structural durability is a growing concern in global infrastructure. The infrastructure report card released by the American Society of Civil Engineers (ASCE) indicates that approximately 9.1% of the total bridges in the United States were structurally deficient in 2016. In addition, it suggests that about 40% of the total bridges in the country are now 50 years or older. This issue becomes even more critical in structures exposed to aggressive environments such as marine structures. Thus, federal and regional efforts are now being directed towards infrastructural durability improvement to improve the long-term cost-efficiency of civil infrastructure.

Corrosion prevention strategies may …

Corrosion Durability Service Life Of Calcium Silicate-Based Reinforced Concrete, Carolina Páez Jiménez

USF Tampa Graduate Theses and Dissertations

Corrosion of reinforcing steel is a major area of study for assessing durability of reinforced concrete infrastructure. Conventional concrete infrastructure designs use ordinary Portland cement (OPC) as the primary cementitious material. However, the world's current challenge to achieve sustainable development requires the cement industry to reduce its environmental impact, as it is responsible for 8% of the anthropogenic CO2 emissions. Hence, a new type of cement has been developed. This novel calcium silicate cement (CSC) reduces the carbon dioxide emissions during its manufacturing process as compared to OPC, providing an environmentally-sound alternative for reinforced concrete fabrication.

Corrosion of steel reinforcement …

A Framework To Aid Decision Making For Smart Manufacturing Technologies In Small-And Medium-Sized Enterprises, Purvee Bhatia

USF Tampa Graduate Theses and Dissertations

The fourth industrial revolution or Industry 4.0 has changed today’s manufacturing scenario. The transition to smart manufacturing technologies has been evolving over the last few years and has recently accelerated due to the pandemic. The need to make manufacturing systems agile, adaptive, resilient, and robust has expediated the adoption and implementation of smart manufacturing technologies.

Despite the interest of manufacturers in smart manufacturing, the adoption rate has been slow due to the lack of decision-making tools that can provide a clear strategic roadmap for effective execution. Small and medium sized enterprises (SMEs) are especially slow in adoption due to the …

Sustainability Assessment Of A Pressure Retarded Osmosis System, Samar Al Mashrafi

USF Tampa Graduate Theses and Dissertations

Desalination has the potential to provide a stable supply of clean fresh water and meet the increasing water demands; however, this process does come with a few challenges such as high energy consumption, high energy cost, and a discharge of a highly concentrated brine. Pressure retarded osmosis (PRO) is a technology that could work as an efficient energy recovery technology for desalination since it can significantly reduce the energy consumption and dilute the brine before discharge. Studies have assessed the economic feasibility of PRO systems; however, these studies have not addressed the environmental sustainability of the systems. Thus, there is …

Issue 7: Contributors, David Hartshorn, Martin Jarrold

Online Journal of Space Communication

List of Issue 7 Contributors.

Future Solutions: Access To Ict: A Tale Of Three Briefings, David Hartshorn

Online Journal of Space Communication

If your inbox is anything like mine, then you already know that the publication of satellite communications reports has become an industry unto itself. But that's not to say that it's always an end unto itself. On the contrary.

Future Solutions: Universal Access, David Hartshorn

Online Journal of Space Communication

Today, the nations of the world have an immediate opportunity to advance essential telecommunication policy objectives through harmonisation of regulations governing the use of fixed satellite-based network solutions.

Regulatory Reform: Strengthening Access To Information & Communications Technologies: Guidelines To Facilitate Policy & Regulation For Satellite Services, Global Vsat Forum

Online Journal of Space Communication

This document was prepared by GVF, an association of organisations engaged in the delivery of advanced broadband and narrowband satellite services to consumers, and commercial and government enterprises worldwide.

Regulatory Reform: In The Land Of The 'Coffeenet', Martin Jarrold

Online Journal of Space Communication

Sitting down to write this article at a desk some 30 miles south of central London, and less than one degree west of the Greenwich meridian, I became immediately more conscious than usual of geography. The frequently interwoven use of such western-centric cartographic labels as Middle East, and Far East, with the geographically more precise terms of Western or Central Asia, and East and South-East Asia, sometimes causes us to confuse the actual proximity of Europe's, much larger, near-neighbour.

Regulatory Reform: Asia's Great Step Forward, David Hartshorn

Online Journal of Space Communication

This paper was presented at Connect-World Asia Pacific, June 2002.

Forget about a great leap forward. All that's needed to facilitate communications in Asia are a few small steps. Indeed, today all nations of the world have an immediate opportunity to advance essential telecommunication policy objectives through harmonisation of regulations governing the use of telecommunications solutions.

Regulatory Reform: Wanted: A Bridge For Africa's Digital Divide Apply: Pretty Much Anywhere In Africa Quote Reference: Vsat, Martin Jarrold

Online Journal of Space Communication

For Africa, and for the economy of the whole planet, those hundreds of millions of people across the continent who are currently denied reasonable access to even simple voice service represent a vast untapped pool of creativity. This very large and potentially very powerful economic dynamo demands access to more than the simplest tools of communication, and requires the means to unleash the potential productivity of its own knowledge-base into an increasingly connected world. The International Telecommunications Union acknowledges this, as does its sister organisation, the United Nations. The Global VSAT Forum enjoins you to acknowledge it too.

Overview: A+B+C = Vsat, Martin Jarrold

Online Journal of Space Communication

The benefits of VSAT systems and services are being realised in all spheres across the globe, both private and public. Banks, government departments, schools, hospitals, home offices, small enterprises, multi-national corporates, and rural telephony… all sectors are seizing upon the opportunity to get connected through satellite communications.

Overview: Satellite Communication In Ghana - Challenges And Prospects, Kwasi Boateng

Online Journal of Space Communication

Busy Internet is a Ghanaian ISP that uses satellite connectivity to bring Internet to West Africans. The operations of this ISP illustrate the reliability, versatility and efficiency of, VSAT, (Very Small Aperture Terminal) networks in delivering fast broadband Internet services.

Overview: The View From 22,300 Miles High, David Hartshorn

Online Journal of Space Communication

Asia's geography, claiming many of the world's highest peaks, has provided a dramatic setting for a climbing expedition that began decades ago, when the satellite communications community took its first step on the lower slopes of the mountain.

Overview: Politics And Technology Converge: Case Studies On The Effects Of Regulatory Reform On Vsat Adoption In Developing Countries, Emmanuel Adugu, Kwasi Boateng, D. Flournoy, Eric Gavua, Wencelous Kaswoswe, Miao Zhang

Online Journal of Space Communication

Developing countries are actively implementing satellite data networks, and have undertaken policy reforms to facilitate such networks. This research examines how regulatory changes have resulted in the removal of barriers relating to the deployment of access technologies and growth in connectivity, especially in VSAT installations for low cost Internet access. In addition, this research seeks to identify the socio-economic impact of emerging data network applications in government, business, health and education. In some cases, government offices have been the driver of change; in other cases, businesses have been the ones to initiate and press these developments forward.

Overview: Pipelines Of The Skies, Errol Olivier

Online Journal of Space Communication

Advances in fixed satellite technology are enabling oil and gas concerns to enhance the efficiency of offshore operations with cost-effective voice and data network solutions.

Issue 7: From The Guest Editors, David Hartshorn, Martin Jarrold

Online Journal of Space Communication

During the past 15 years, the international satellite communications industry has been developing and refining network solutions such that today, there are more than one million so-called Very Small Aperture Terminal (VSAT) systems installed and operating in more than 120 countries.

A Laboratory Investigation Of High Polymer Modified Asphalt Mixtures With Softening Agent, Basel K. Al-Badr

Theses and Dissertations

This study was initiated to evaluate the impact of aging and High Polymer Modified Asphalt (HPMA) binders containing a bio-based-oil softening agent (SA) on the rutting, cracking, and durability of asphalt mixtures. One control asphalt binder (PG 52-34), Styrene-Butadiene-Styrene (SBS) polymer modifier, and corn-oil SA were used to produce four asphalt mixtures including a control prepared using PG 52-34 binder and three modified mixtures were produced by blending PG 52-34 binder with different dosages of SBS and SA. The mixtures were tested using the Dynamic Complex Modulus (|E*|), Hamburg Wheel Tracking Device (HWTD), Flow Number (FN), Indirect Tension Cracking Test …

Kinematic Analysis Of Gait In An Underwater Treadmill Using Land-Based Vicon T 40s Motion Capture Cameras Arranged Externally, Shreyas L. Raghu, Ryan T. Conners, Chang-Kwon Kang, David B. Landrum, Paul N. Whitehead

PRC-Affiliated Research

Aquatic therapy for rehabilitation can be performed in a variety of environments, which can vary from a traditional swimming pool to a self-contained underwater treadmill. While kinematic analysis has been performed in large volume swimming pools using specific underwater motion capture systems, researchers may only have access to a land-based motion-capture system, which is not waterproof. Additionally, underwater motion capture systems may not fit within the confines of a smaller underwater treadmill. Thus, the purpose of this study was to design and analyze methodology to quantify lower limb kinematics during an aquatic treadmill session, using a land-based motion capture system. …

Kinematic Analysis Of Gait In An Underwater Treadmill Using Land-Based Vicon T 40s Motion Capture Cameras Arranged Externally, Shreyas L. Raghu, Ryan T. Conners, Chang-Kwon Kang, David B. Landrum, Paul N. Whitehead

PRC-Affiliated Research

Aquatic therapy for rehabilitation can be performed in a variety of environments, which can vary from a traditional swimming pool to a self-contained underwater treadmill. While kinematic analysis has been performed in large volume swimming pools using specific underwater motion capture systems, researchers may only have access to a land-based motion-capture system, which is not waterproof. Additionally, underwater motion capture systems may not fit within the confines of a smaller underwater treadmill. Thus, the purpose of this study was to design and analyze methodology to quantify lower limb kinematics during an aquatic treadmill session, using a land-based motion capture system. …