Engineering Commons^™

Hydrocarbon Source Rocks In Kazhdumi And Pabdeh Formations—A Quick Outlook In Gachsaran Oilfield, Sw Iran, Majid Safaei-Farouji, Mohammadreza Kamali, Mohammad Hail Hakimi

Research outputs 2014 to 2021

Geochemical study of Kazhdumi and Pabdeh Formations as potential source rocks in Gachsaran Oilfield demonstrates that the Kazhdumi Formation has a fair to good capability of hydrocarbon generation and predominately contains type II-III kerogen. On the other hand, the Pabdeh Formation has a poor to good petroleum potential and contains different kerogen types, including type II, type II-III, type III and even for one sample, type IV, indicating different depositional conditions for this formation. The geochemical log of the Kazhdumi Formation shows that there is a close correlation between different geological parameters as noticed prominently in well number 55, which …

Influence Of Mineralogy And Surfactant Concentration On Zeta Potential In Intact Sandstone At High Pressure, Faisal Ur Rahman Awan, Ahmed Al-Yaseri, Hamed Akhondzadeh, Sefan Iglauer, Alireza Keshavarz

Research outputs 2014 to 2021

Hypothesis:

Zeta-potential in the presence of brine has been studied for its application within hydrocarbon reservoirs. These studies have shown that sandstone’s zeta-potential remains negatively charged, non-zero, and levels-off at salinities > 0.4 mol.dm⁻³, thus becoming independent of salinity when ionic strength is increased further. However, research conducted to date has not yet considered clay-rich (i.e. clay ≥ 5 wt%) sandstones.

Experiments:

Firstly, streaming potential measurements were conducted on Bandera Gray sandstones (clay-rich and clay-poor) with 0.6 and 2 mol.dm⁻³ NaCl brine-saturated in pressurised environments (6.895 MPa overburden and 3.447 MPa back-pressure). Secondly, the streaming potential was determined …

Examining The Relationship Among Perceived Academic Climate, Belongingness, And Engineering Identity, Sumaia Ali Raisa

Graduate Theses, Dissertations, and Problem Reports (ETD)

An attempt to cultivate an inclusive learning environment in engineering is trending as a response to women's underrepresentation and a lower retention rate than men undergraduates. This study was situated in such an undergraduate engineering program where interventions were embedded in the course curriculum focusing on cultivating an inclusive engineering identity. Following a sociocultural perspective, the present study aimed to examine the relation of engineering identity with perceived academic climate, sense of belonging, and gender among two engineering cohorts (before covid and during covid context). A total of 482 first-year engineering undergraduates' survey responses were analyzed in this study using …

Methodology For Enhanced Filtration And Dewatering Of Fine-Grain Amd Precipitate Using Geocomposites For Rare Earth Elements Recovery, Iuri Lira Santos

Graduate Theses, Dissertations, and Problem Reports (ETD)

Research performed by the West Virginia Water Research Institute (WVWRI) in partnership with the Department of Energy (DOE) has identified that coal mining by-products contain significant amounts of Rare Earth Elements (REEs). REEs currently are in high demand, and extraction from coal mining reject presents a potential for commercialization if extraction is feasible. The coal mining reject include Acid Mine Drainage (AMD) in the aqueous phase and sludge from AMD treatment. A novel two split selective precipitation method was implemented to remove gangue metals, increasing the concentration of REEs in the sludge.

This process presents a two-fold benefit: 1) treatment …

Clean Process To Utilize The Potassium-Containing Phosphorous Rock With Simultaneous Hcl And Kcl Production Via The Steam-Mediated Reactions, Yunshan Wang, Lufang Shi, Houli Li, Yixiao Wang, Zhiying Wang, Xuebin An, Mingzhu Tang, Gang Yang, Jun He, Jing Hu, Yong Sun

Research outputs 2022 to 2026

In this paper, a clean process based on the steam-mediated reactions for simultaneous HCl and KCl production using the potassium (K)-containing phosphorous rock as a precursor is proposed. Through hydrochloric acid (HCl) leaching, not only the generation of H₃PO₄and CaCl₂ (via further precipitation) were realized but also the acid-insoluble residue [phosphorous-rock slag (PS)] rich in elements, that is, K, Al, Si, and so on, in the form of microcline (KAlSi₃O₈) and quartz (SiO₂) was obtained and became readily available for further HCl and KCl generation. Over 95 % of …

Impacts Of Atmospheric Stilling And Climate Warming On Cyanobacterial Blooms: An Individual-Based Modelling Approach, Mohammad Hassan Ranjbar, David P. Hamilton, Amir Etemad-Shahidi, Fernanda Helfer

Research outputs 2022 to 2026

Harmful algal blooms of the freshwater cyanobacteria genus Microcystis are a global problem and are expected to intensify with climate change. In studies of climate change impacts on Microcystis blooms, atmospheric stilling has not been considered. Stilling is expected to occur in some regions of the world with climate warming, and it will affect lake stratification regimes. We tested if stilling could affect water column Microcystis distributions using a novel individual-based model (IBM). Using the IBM coupled to a three-dimensional hydrodynamic model, we assessed responses of colonial Microcystis biomass to wind speed decrease and air temperature increase projected under a …

Physical Layer Authentication Using Ensemble Learning Technique In Wireless Communications, Muhammad Waqas, Shehr Bano, Fatima Hassan, Shanshan Tu, Ghulam Abbas, Ziaul Haq Abbas

Research outputs 2022 to 2026

Cyber-physical wireless systems have surfaced as an important data communication and networking research area. It is an emerging discipline that allows effective monitoring and efficient real-time communication between the cyber and physical worlds by embedding computer software and integrating communication and networking technologies. Due to their high reliability, sensitivity and connectivity, their security requirements are more comparable to the Internet as they are prone to various security threats such as eavesdropping, spoofing, botnets, man-in-the-middle attack, denial of service (DoS) and distributed denial of service (DDoS) and impersonation. Existing methods use physical layer authentication (PLA), the most promising solution to detect …

Optimal Sizing And Energy Scheduling Of Grid-Supplemented Solar Pv Systems With Battery Storage: Sensitivity Of Reliability And Financial Constraints, Aakash Hassan, Yasir M. Al-Abdeli, Martin Masek, Octavian Bass

Research outputs 2022 to 2026

Establishing reliable, clean, and inexpensive solar PV systems is a complex interplay between the level of reliability (LPSP), financial constraints, and CO2 emissions. This paper investigates the impact of these factors on stand-alone (SA) and grid-supplemented (GS) solar PV systems over multiple seasons. The research uses established hardware models, detailed power management strategies as well as realistic Australian grid tariffs and Genetic Algorithms to find the minimum Cost of Energy (COE) subject to LPSP and financial constraints. The developed power management strategies are also tested experimentally on a real solar PV system. The results indicate that the grid-supplemented system yields …

A Magnetic Nanoparticle-Doped Photopolymer For Holographic Recording, Muhammad Irfan, Suzanne Martin, Muhammad Ahmed Obeidi, Scott Miller, Frank Kuster, Dermot Brabazon, Izabela Naydenova

Articles

Functionalised holograms are important for applications utilising smart diffractive optical elements for light redirection, shaping and in the development of sensors/indicators. This paper reports on holographic recording in novel magnetic nanocomposites and the observed temperature change in dry layers and liquid samples exposed to alternating magnetic field (AMF). The nanocomposite consists of N-isopropylacrylamide (NIPA)-based polymer doped with magnetic nanoparticles (MNPs), and local heating is achieved through magnetic induction. Here, volume transmission holographic gratings (VTHGs) are recorded with up to 24% diffraction efficiency (DE) in the dry layers of magnetic nanocomposites. The dry layers and liquid samples are then exposed to …

Towards Plasmon Mapping Of Sers-Active Ag Dewetted Nanostructures Using Spels, Mohamed Beshr, E. Dexter, Paul E. Tierney, Aidan Meade, Shane Murphy, George Amarandei

Articles

Thermal dewetting of silver thin flm can lead to SERS-active Ag nanoparticles. Here, we report our progress towards using scanning probe energy loss spectroscopy (SPELS) to map the plasmonic behaviour of SERS-active Ag nanoparticles (NP) by investigating NPs produced through the dewetting study of Ag thin flms on SiO2/Si and Ti/SiO2/Si substrates. The nanoparticles size and spatial distribution were controlled by the deposition and thermal annealing parameters. The results of preliminary SPELS measurements of these structures, alongside SERS data show that there is a correlation between the Raman enhancement and the nanoparticle size and interparticle spacing.

Graphene Derivatives Reinforced Metal Matrix Nanocomposite Coatings: A Review, Hamed Sadabadi, Omid Ghaderi, Amir Kordijazi, Pradeep K. Rohatgi

Journal of Metals, Materials and Minerals

Due to the extraordinary mechanical, thermal, and electrical properties of graphene, graphene oxide (GO), and reduced graphene oxide (rGO), these materials have the potential to become ideal nanofillers in the electrodeposited nanocomposite coatings. This article provides an overview of literature on the improvements of properties associated with graphene, GO, and rGO-reinforced coatings, along with the processing parameters and mechanisms that would lead to these improvements in electrodeposited metal matrix nanocomposite coatings, where those affected the microstructural, mechanical, tribological, and anti-corrosion characteristics of coatings. The challenges associated with the electroplating of nanocomposite coatings are addressed. The results of this survey indicated …

The Correlation Between Phase Formation And The Structure Of The Pellets With The Fungal Immobilization Study As A Commercial Substrate Culture/Planting Material, Rattiphorn Sumang, Rampai Kodsueb, Narathip Vitayakorn, Ruangwut Chutima

Journal of Metals, Materials and Minerals

Calcined clay pellets are popular planting material for those who love to grow plants in pots. The calcined clay pellets consist of clay (C), phosphate rock (PR), and rice husk ash (RHA). [(1-x)(50C–50PR)-xRHA], x(RHA) = 0, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55, 0.60, and 0.65 wt% were prepared by a conventional solid-state reaction method. The samples were made into a spherical shape with a diameter of 10 mm and fired at 600℃ to 1000℃. The effect of x contents on phase formation, microstructure, and chemical properties of [(1-x)(50C–50PR)-xRHA] was studied. X-ray diffraction revealed the typical assemblages with quartz, illite, …

Synthesis And Antimicrobial Studies Of Nano-Copper Doped Carbon Substrates; Activated Carbon, Reduced Graphene Oxide, And Carbon Nanofiber, Songwuit Chanthee, Jenjira Jirasangthong, Channarong Asasvatesanupap, Malee Santikunaporn

Journal of Metals, Materials and Minerals

Copper oxides (CuxO) have received considerable attention as a result of their biological activity. Nanoparticles (NPs) of CuxO attached to different substrates exhibit a wide spectrum of antimicrobial activity against bacteria and viruses, with similar properties to silver. The antimicrobial activity of CuxO-NPs doped on distinctive carbon materials was investigated for three carbon substrates: apricot stone activated carbon (AAC), reduced graphene oxide (rGO) and carbon nanofiber (CNF). The CuxO-NPs (5 wt%) doped AAC and rGO substrates were prepared by impregnation of copper nitrate followed by a thermal treatment process, while a similar weight of CuxO-NPs doped CNF was fabricated by …

Preparation Of Feedstock Containing Water-Soluble Binder For Powder Injection Moulding Of Silver, Chuanchom Aumnate, Nithiwach Nawaukkaratharnant, Nutthita Chuankrerkkul

Journal of Metals, Materials and Minerals

Feedstock for powder injection moulding of silver was prepared using water-soluble binder composed of polyethylene glycol (PEG) and polyvinyl butyrol (PVB). Silver powders with particle size in range of 1 μm to 20 μm can be mixed with PEG/PVB binder system to form feedstocks having powder loadings of 42 vol% and 45 vol%. PEG can be removed using water leaching method while PVB can be removed by thermal debinding. Specimens retained their shapes during debinding and after debinding. Components fabricated with relatively higher powder loading resulted in higher density with lower porosity. Density of specimens containing powder loading of 42 …

Tungsten Disulfide-Nickel Oxide Hybrids As High-Performance Supercapacitors, Zainab Ali Hrbe, Samaher Waheed Hashim

Journal of Metals, Materials and Minerals

Two-dimensional materials are suitable for energy storage applications due to their chemical stability, high electrical conductivity and large specific surface area. In this work, tungsten disulfide (WS2) nanosheets were synthesized by chemical exfoliation method and combined with nickel oxide (NiO) nanoparticles to be used as a working electrode for storing energy. The WS2 electrode alone shows a capacitance of about 21.87 mF⸳cm-2, which is improved up to 64.58 mF⸳cm-2 by adding NiO nanoparticles. The occurrence of redox reactions plays an important role in increasing the final capacitance. Moreover, the proposed hybrid maintains 93% of its initial capacitance after 5000 charge-discharge …

The Influence Of Different Crystal Modifiers On Ultra-Low Embodied Energy Curing Fiber-Reinforced Cement Composites, Passakorn Sonprasarn, Wichit Prakaypan, Sureerat Polsilapa, Nuntaporn Kongkajun, Edward A. Laitila, Nutthita Chuankrerkkul, Parinya Chakartnarodom

Journal of Metals, Materials and Minerals

Fiber-reinforced cement composites (FRCC) are widely used in the construction of houses and commercial buildings in many countries such as the United States, the United Kingdom, the European countries, and the Asian countries such as China, India, and Thailand.  Conventionally, the FRCC is manufactured from Portland cement, silica sand, and cellulose fiber using the so-called autoclaved curing under a designate hydrothermal condition to accelerate the hydration reaction resulting in superior properties.  However, the autoclave-curing process needs a huge investment and generates highly environmental impact specially greenhouse gases due to its heavy energy consumption.  Hence, this research aims to develop the …

Sequential Injection Analysis For Mercury Ion With Modified Screen – Printed Carbon Electrode, Eakkasit Punrat, Naphat Piyasart, Chalinee Auanphui, Rutanachai Thaipratum, Shoji Motomizu, Wanida Wonsawat

Journal of Metals, Materials and Minerals

In this study, we developed a simple high-throughput and cost-effective method for monitoring toxic metal ion in an environmental aqueous sample. Mercury ion determination with Sequential Injection Analysis system (SIAs) coupled with the electrochemical detection on the modified screen-printed carbon working electrode (SPCE) is an alternative green analysis of mercury ion. The gold film was used as the modified material for improved mercury ion analysis in the automated system without memory effect on the electrode. Mercury oxidation signal was found at the potential of 0.7 V in 0.1 M HNO3 and 1.0 M HCl with the concentration low to 0.25 …

Effect Of A-Site Modification On Structural And Microwave Dielectric Properties Of Calcium Titanate, Shailendra Rajput, Sunita Keshri

Journal of Metals, Materials and Minerals

This article presents studies on characteristics properties of CaTiO3, Ca0.8Sr0.2TiO3, and Ca0.6La0.8/3TiO3 ceramics. These ceramics were synthesized using the solid-state reaction process. Structural examination revealed that the grown ceramics have an orthorhombic structure with the Pbnm space group. The random distribution of particle size was shown through morphological investigation. Apparent density of developed ceramics was determined using the Archimedes technique and found to be ˂ 90%. The microwave dielectric properties of grown ceramics are compared on the basis of ionic polarizability. It is observed that partial replacement of Ca-ions by Sr-ions provides a high permittivity value (er = 168.93), higher …

Hole Transport Layers In Organic Solar Cells: A Review, Riva Alkarsifi, Jörg Ackermann, Olivier Margeat

Journal of Metals, Materials and Minerals

Thanks to huge research efforts, organic solar cells have become serious candidates in the field of renewable energy sources, with reported power conversion efficiencies above 19% and operating lifetime surpassing decades. In the thin film stack composing the organic solar cell, the transport layers at interfaces play a key role, as important as the photoactive material itself. Both electron (ETL) and hole (HTL) transport layers are indeed directly involved in the efficiency and stability of the devices, due to the very specific properties required for these interfaces. Focusing on the HTL interface, a large number of materials has been used …

Research Progress Of Novel Zirconium Alloys With High Strength And Toughness, Na Zhang, Chaoqun Xia, Jiaqian Qin, Qiang Li, Xinyu Zhang, Riping Liu

Journal of Metals, Materials and Minerals

Atoms of zirconium (Zr) are often known as "first metals of the atomic age". Because of its low cross section for thermal neutron absorption, excellent corrosion resistance, and good mechanical and processing properties, it is extensively used in the nuclear industry. As the properties requirements of materials in chemical, medical and aerospace fields turn out to be higher, the application of Zr alloys in these non-nuclear fields has become more and more widespread due to their excellent properties. In addition to having a high melting point, Zr alloys also have a high specific strength and low thermal expansion coefficient. Therefore, …

Rice Husk Ash Utilization, Composition And Properties: A Brief Review, Vignesh Nayak Ullal, Shivaramu H. T., Aveen K. P.

Journal of Metals, Materials and Minerals

Asian countries rely massively on rice to feed and sustain its massive population. For long the staple food has provided nourishment to the masses and the classes. Rice is grown in large quantities in Asian countries. A by-product of its cultivation is its husk. The husk of the rice grain is mainly utilized as a fuel for the boilers in the rice mills. The uncontrolled burnt rice husk referred to as rice husk ash consists majorly of silica. silica is used in a wide variety of commercial and industrial applications. Use of rice husk ash in various products serves to …

Extraction Of Lutein Dye From Tagetes Erecta Garland Waste For Green Dyeing Of Hemp Fabric Using Response Surface Methodology, Pisutsaran Chitichotpanya, Nattaya Vuthiganond, Thitirat Inprasit, Benjamas Klaykruayat, Seranee Srisuk

Journal of Metals, Materials and Minerals

Large quantities of discarded flowers from religious observances are left at temples and other places of worship, causing global disposal and environmental issues. Recycling and transforming such organic waste into value-added products is one of the most effective and beneficial solutions to the problem. The main goal of this study is to convert the most abundant temple wastes of marigold (Tagetes erecta) flowers into an eco-friendly dyestuff for the textile industry. Our study assessed the suitability of dye extract from garland waste for dyeing hemp fabric and valuated indicators including color strength (K/S) and fastness properties using tannic …

Development Of Fexoy Particle Onto Bacterial Cellulose Network By Forced Hydrolysis And Its Electrical Conductivity, Prompong Khamwongsa, Poramed Wongjom, Andi Magattang Gafur Muchlisc, Chun Che Lin, Seranee Srisuk, Sarute Ummartyotin

Journal of Metals, Materials and Minerals

FexOy particle and bacterial cellulose composite sheet was successfully prepared by forced hydrolysis. The presence of Fe3+ ions in bacterial cellulose suspension significantly provided the positive charge due to electrostatic force as reported by Zeta potential. With the pH of 12 of bacterial cellulose suspension, particle was nucleated between bacterial cellulose networks. Fourier transform infrared exhibited Fe-O stretching. X-ray diffraction reported that the mixture of Fe2O3 and Fe3O4 was existed onto bacterial cellulose composite. Scanning electron microscope reported that FexOy particle was randomly distributed in bacterial cellulose network. Intensity of Fe was qualitatively observed by energy dispersive analysis. With the …

Morphology And Electrochromic Property Of Chemical Bath Deposited Nio Films At Different Niso4 Concentration, Watcharaporn Thongjoon, Kamon Aiempanakit, Itsarapong Chuasontia, Chantana Aiempanakit

Journal of Metals, Materials and Minerals

In this study, nickel oxide (NiO) films were prepared on indium tin oxide (ITO) glass by a chemical bath deposition (CBD) at different nickel sulfate (NiSO4) concentrations. The NiO films were verified for their structural properties with field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) while the optical properties were investigated using a spectrophotometer. Moreover, the NiO films were studied to assess their electrochemical properties by cyclic voltammetry in potassium hydroxide (KOH) electrolyte. The results showed that annealed NiO films exhibited the dominant crystal structure of the (111) plane. Meanwhile, the NiSO4 concentration controlled morphological structure between dense …

Optimized Parameter Of Dissimilar Joining Between Al6061-T6 And Height-Strength Steel With Friction Stir Spot Welding Process (Fssw), Anusak Silachai, Suriya Prasomthong

Journal of Metals, Materials and Minerals

High-strength steel and aluminum alloys are used to manufacture modern vehicles. The objective was to reduce the weight and fuel consumption of the vehicles. In this study the optimum parameters for the friction stir spot welding (FSSW) process between Al6061-T6 aluminum alloy and HSS590 high-strength steel were determined. Response surface methodology based on central composite design (CCD) with three parameters, five levels, and 19 runs was used to conduct experiments and develop mathematical regression models. The three joint parameters were tool speed, welding feed, and dwell time. Analysis of variance was then performed to examine the adequacy of the developed …

Synthesis And Characterization Of Hybrid Shell Microcapsules For Anti-Corrosion Ni-Co Coating, Hamed Sadabadi, Saeed Reza Allahkaram, Omid Ghader, Pradeep K. Rohatgi

Journal of Metals, Materials and Minerals

This paper presents the results of the study of microcapsules synthesized using a novel hybrid shell of polyureaformaldehyde/SiO2 (PUF/SiO2) and a core of linseed oil. The synthesis was accomplished by facial polymerization combined with sol-gel of TEOS, and urea-formaldehyde resin to form the hybrid shell under optimal process parameters. The microcapsules were embedded in a metal coating using the electrodeposition method. Microcapsules were characterized by scanning electron microscope (SEM, FE-SEM), energy-dispersive spectroscopy (EDS), particle size analyzer (PSA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The experimental results indicated that the average size of capsules synthesized umder the optimum processing …

Dyeing Of Curcumin And Durable Press Finishing With Citric Acid On Cotton Fabric Using One Step Process, Supannee Boonroeng, Piyaporn Kampeerapappun

Journal of Metals, Materials and Minerals

Cotton is an affordable and durable option for clothing. However, cotton garments tend to wrinkle easily. Therefore, cotton fabrics were studied to improve their wrinkle resistance properties. In this work, curcumin was mixed in an aqueous solution of citric acid and its catalyst and applied to cotton fabric using pad-dry-cure process for both the dyeing and finishing properties. Aloe vera extract and chitosan were used to compare for the reaction of their functional groups with carboxyl groups of citric acid on cotton fabrics. The mixture of curcumin and citric acid solution showed anti-wrinkle properties on the treated cotton. There were …

Mineralogical Studies And Optimization Of Tabling Parameters Of Low Grade Chromite Ore By Box Behnken Design Of Experiments, Amit Kumar Bhandary, Siddhartha Mukherjee, Rajib Dey, Mahua Ghosh Chaudhuri

Journal of Metals, Materials and Minerals

Chromite ore is geologically associated with gangue materials which have lower density compared to pure chromite (FeO.Cr2O3). Gravity separation techniques are very suitable for beneficiation of low grade chromite ore. In the present study mineralogical analysis of the sample has been carried out by using Wavelength dispersive x-ray fluorescence (WDXRF), X-ray powder diffraction (XRD), Scanning electron microscopy (SEM) and Energy dispersive X-ray (EDX). The beneficiation of low grade (Cr2O3% 26.88) chromite ore has been investigated using wilfley table. Optimization has been carried out using box-behnken statistical design (BBD). The experimental parameters selected are: tilt angle, water flow rate and pre-heat …

Magnetic Nanoparticles Coated With Zwitterionic Copolymer As An Advanced Material For Rapid And Instrument-Free Biomolecular Detection In Human Serum, Supannika Boonjamnian, Varunee Sadsri, Voravee P. Hoven, Piyaporn Na Nongkhai

Journal of Metals, Materials and Minerals

The traditional agglutination assays especially those based on polystyrene beads have been recognized as convenient tools for disease diagnosis despite their limited detection range and low sensitivity. Unlike other particles namely polystyrene beads, SiO2 and gold nanoparticles having insignificant magnetic properties, magnetic nanoparticles (MNPs) offer unique advantages as their magnetic properties for agglutination methods. In the presence of magnet, not only can they be used to enrich the samples, but also their aggregation can also be induced, providing sensitive and rapid measurements. This work aims to develop MNPs for aggregation-based biomolecular detection. The MNPs were surface-modified with PMAMPC via an …

Selective Harmonic Mitigation Based Two-Scale Frequency Control Of Cascaded Modified Packed U-Cell Inverters, Hasan Iqbal, Mohd Tariq, Mohammad Sarfraz, Arif I. Sarwat, Waleed Alhosaini, Obaid Aldosari, Asma Aziz

Research outputs 2022 to 2026

A new Modified Packed U-Cell (MPUC) converter architecture with cascading is proposed in this paper. To provide an output voltage of 25 levels, the proposed cascaded MPUC needs only twelve power switches and four power sources. The converter comprises two cascaded MPUCs with DC supply in a ratio of 5 : 1. One converter is operating at low frequency (LF) and the other at high frequency (HF) that leads to lower power losses and higher levels. Besides, a variable frequency method is anticipated to produce a 25-level output voltage which has low harmonic content (THD) with the help of Selective …