Engineering Commons^™

Development Of A Catalytic System Based On N,N’,N”-Tris-(Β-Oxyethyl)Hexahydro-S-Triazine For Polyisocyanuraturethane Foam, Murod K. Karimov, Nozima M. Alimukhamedova, Lochinbek M. Khurramov, Ravshan I. Adilov, Murafar G. Alimukhamedov

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this work is to develop a catalytic system for the production of polyisocyanurateurethane foams based on N,N',N"-tris(β-hydroxyethyl)hexahydro-S-triazine (TOEGT). N,N',N"-tris(β-hydroxyethyl)hexahydro-S-triazine (TOEGT) exhibits high catalytic activity in polyurethane foam production processes. However, it exhibited moderate catalytic activity in polyisocyanurateurethane  foams, the formation of which is characterized by the sequential-parallel reactions of urethane formation, isocyanate trimerization, and foaming (isocyanate + water). By varying the composition of the catalytic mixture, the required concentrations of each component were determined, which made it possible to synthesize polyisocyanurateurethane foams that meet the requirements of casting polyurethane foams. The optimal ratio of N,N',N"-tris(β-hydroxyethyl)hexahydro-S-triazine: triethylenediamine: tin …

Physicochemical Investigation Of Interactions In The Urea – Dl-Alanine System, Suvonkul E. Nurmonov, Saydullo Kh. Azimov

CHEMISTRY AND CHEMICAL ENGINEERING

A comprehensive physicochemical study of the “urea – DL-alanine – water” system was carried out to determine the nature of the interactions between its components. Methods of isomolar series, X-ray phase analysis, thermal analysis, and FTIR spectroscopy were applied. It was found that molecular associates with a stoichiometry of 1:1 are formed in an aqueous solution, as evidenced by deviations in density, viscosity, refractive index, and electrical conductivity from their additive values. In the solid phase, the system represents a mechanical mixture of the initial components without the formation of new crystalline phases. The presence of hydrogen bonds of the …

Extraction Of Metallic Silver In Powder Form From Electronic Wastes, Mastura Kh. Aripova, Umar A. Yakhyaev, Ripsime V. Mkrtchyan, Shoxrux B. Naimov

CHEMISTRY AND CHEMICAL ENGINEERING

The research is dedicated to the extraction of silver in powder form from electronic wastes and the selective separation of associated elements through the application of hydrometallurgical methods. The conducted study determined the initial chemical composition of the electrical engineering waste (wt.%): Si – 0.08, Al – 0.133, Fe – 0.021, Mg – 0.614, Cu – 0.005,  Zn – 0.02, Ag – 46.9,Zr – 0.557,  Ta – 0.004, Pb – 0.003, Mo – 0.002, S – 0.026. A system for the efficient extraction of metals with minimal losses was developed for the selective dissolution of metals such as Cu, Ni, …

Study Of Microstructural Defects Of Drill Bit Teeth Using Microscopic Methods, Odiljon E. Abdurakhmonov, Mastura Kh. Aripova, Orifjon O. Khomidov, Bakhtiyar T. Zakhidov, Amir I. Abidov

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this study is to investigate microstructural defects in drill bit cutting elements, including milled teeth and WC–Co cemented carbide inserts, to clarify their morphology, chemical–phase characteristics, and potential contribution to manufacturing-related defects. To achieve this goal, the study applied a combined approach based on optical microscopy and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM–EDS). First, the study examined surface and microstructural features, such as pores, depressions, and local heterogeneities formed during manufacturing. Then, it conducted detailed SEM–EDS analyses of selected local regions, including crack initiation sites. As a result, the study revealed that cutting elements …

Sorption Of Lanthanum(Iii) Ions On Impregnated Solid Extractants, Jaloliddin Q. Abdurashidov, Tadjigul R. Odamova, Maksim A. Kamarou, Zuhra Ch. Kadirova, Shahlo Sh. Daminova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this work was to obtain solid extractants by impregnating the organic reagent 1-phenyl-1,3-butadione (BNA) onto carriers based on styrene-divinylbenzene copolymers (PAD600, PAD400) as well as activated carbon, and to investigate the sorption isotherms of La³⁺ ions under static conditions. The structure of the sorbents before and after La³⁺ ion sorption was studied using SEM-EDX and IR spectroscopy. The parameters of sorption extraction of La³⁺ ions, including extraction degree, sorbent capacity, and distribution coefficient, were evaluated. It was established that the PAD600-BNA sorbent exhibits the most favorable sorption properties toward La³⁺ ions.

Two-Stage Heat Treatment For Producing Highly Crystalline H-Bn Nanoparticles From Boric Acid And Urea, Sherzod E. Abdurakhmonov, Mastura Kh. Aripova, Umar A. Yakhyaev, Shoxrux B. Naimov, Odiljon E. Abdurakhmonov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of the study was to investigate the formation of the crystal structure of hexagonal boron nitride (h-BN) nanoparticles obtained by the chemical-thermal method using two-stage heat treatment. Boric acid and urea were used as starting precursors, enabling ammonia-free synthesis conditions. It is shown that the first thermal stage at 600 °C under a nitrogen atmosphere leads to the formation of a predominantly amorphous BN-containing precursor, whereas the second stage at 1000 °C in an N₂/H₂ atmosphere promotes crystallization of a highly ordered hexagonal h-BN phase. The morphology and particle size distribution were examined by transmission …

Structure And Morphology Of Ultradispersed Erbium Ytterbium Oxide Powders Obtained By Deposition Method, Eygeniy N. Poddenezhny, Andrei A. Boiko, Natalya E. Drobyshevskaya, Vladimir S. Urbanovich, Ekaterina E. Trusova

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of research is to develop a new method for synthesis of ultra-dispersed crystalline powders of lanthanide oxides, in particular, erbium oxide doped with ytterbium oxide, intended for making transparent ceramics. The formation of nanostructured powders of the erbium oxide – ytterbium oxide system using deposition and heat treatment processes by co-deposition of salt solutions mixed with ammonium carbonate and hydrogen peroxide complex solution at temperature of 10 °C followed annealing at 100, 650, 900 and 1200°C was studied. Studies of the morphological and structural characteristics of the powders using scanning electron microscopy and X-ray phase analysis showed that …

Sweep Angle Effects Of Flow Over A Seal Whisker-Inspired Undulated Cylinder, Trevor Dunt, Christin T. Murphy, Ondrej Fercak, Raúl Bayoán Cal, Jennifer A. Franck

Mechanical and Materials Engineering Faculty Publications and Presentations

Flow over a seal whisker-inspired undulated cylinder at swept back angles is computationally investigated, comparing the vortex shedding, forces, and wake characteristics to those of an equivalent smooth geometry. Numerous prior studies have demonstrated that undulated cylinders can reduce mean drag and unsteady lift oscillations; however, none have isolated the effects of the sweep angle resulting from whisker positioning in flow. Inspired by the active control seals exert over their whiskers while navigating and sensing in unsteady aquatic environments, this study investigates how such orientation influences the hydrodynamic performance of the geometry. Simulations are performed of flow across a rigid, …

Evaluating Runtime Monitoring For Reinforcement Learning-Based Flight Control, Andrew Zubyk

Doctoral Dissertations and Master's Theses

Ensuring safety in adaptive flight controls systems is an ongoing challenge in aviation, especially as advancements in artificial intelligence and machine learning (AI/ML) trend upwards. Reinforcement learning is becoming more common in aerospace applications due to the ability to improve these models through training.  While models such as reinforcement learning enable controllers to learn complex behaviors from interaction with the environment, their unpredictability in novel or disturbed conditions raises severe concerns in safety-critical domains. This research investigates the integration of runtime monitoring, a real-time assurance technique, with reinforcement learning-based flight controllers to ensure safety and reliability during flight. By supervising …

A Pretraining-Based Framework For On-Device Training Of Imu-Based Locomotion Mode Detection For Wearable Active Exoskeletons, Muhammad Tahir Khan

LSU Master's Theses

Active exoskeletons are being developed to support human movement in physically demanding industries such as construction. For these systems to work effectively, they must be able to correctly identify the user’s current activity. This process is known as locomotion mode detection and plays an important role in selecting the appropriate control parameters for exoskeletons. Many existing approaches use inertial measurement units (IMUs) to recognize these activities and have shown strong performance. However, most of these methods depend on large amounts of labeled data collected under specific conditions. As a result, they often do not perform well when applied to new …

Wearable Sensor System Used To Measure Linear And Angular Acceleration Of The Head Of American Football Players, David A. Emerson

LSU Master's Theses

American football players are repeatedly subject to high-velocity impacts; collisions can exceed 100 g in the NFL [1]. Rotational accelerations of the head caused by high-velocity collisions have been proven to be extremely damaging to the highly organized brain fibers at the brain-skull interface [2]. The sensor system (SS) measures the nonplanar acceleration at four locations on a chin strap using ADXL314 accelerometers and utilizes rigid-body kinematics to estimate the head rotational state from the measured acceleration of the SS [3]. The SS was validated through progressive testing, including steady-state, linear impact, and rotational impact testing. The ADLX314 sensor exhibited …

Reconstruction Of Information System Acceptance Model In The Era Of Integrated Artificial Intelligence: A Systematic Literature Review, Ilham, Merlin Apriliyanti

Library Philosophy and Practice (e-journal)

This study aims to explain the rapid development of Artificial Intelligence (AI) which has driven significant transformations in the development and use of information systems. However, most classical information system acceptance models, such as the Technology Acceptance Model (TAM) and  (UTAUT), have not been able to fully explain the unique characteristics of AI-based systems that are autonomous, adaptive, and complex. This study aims to reconstruct the information system acceptance model in the era of integrated AI through a Systematic Literature Review (SLR) approach. This study was conducted using the PRISMA protocol on 130 leading scientific articles indexed by Scopus and …

Slender And Nonslender Delta Wing Simulation And Analysis, Aashish Gyawali, Brinda Bhattarai, Nishesh Bista, Sundeep Rao Dr

Journal of Aviation Technology and Engineering

Stability, controllability, and maneuverability are critical factors for aircraft with short takeoff and landing distances, such as modern fighter aircraft and unmanned aerial vehicles. Delta wings are commonly employed in these aircraft due to their efficient aerodynamics, enabling high maneuverability, and performance at both low and high speeds. Nonslender wings are used for low-speed performance and agility, while slender wings offer reduced drag and are suited for high-speed operations. In flight, an aircraft encounters different airflow patterns including vortices that circulate from the higher-pressure lower side of the wing to the lower-pressure upper side, contributing to lift generation. However, as …

The Waldo Dataset, Mary E. Koone, Rosie Kallie, Vassilis Athisos, Laurel S. Stvan

Computer Science and Engineering Datasets - Archive

Distinct from the task of predicting the author of a document (authorship attribution), we focus on addressing the issue of how to estimate the similarity between the written language styles of authors. To do so, we present a dataset of metadata derived by asking human annotators, who were presented with three documents, to identify which two were written by the same author and which was written by a different author. The dataset has over 400 such annotations, creating a companion to the Amazon Web Services (AWS) customer review dataset, laying the groundwork for crowdsourcing applications to other natural language processing …

Virtual Humans In Virtual Reality: A Scoping Review On Sociability, Fidelity, And Expression, J K Sangeeth Chandran, Marisa Llorens Salvador, Cathy Ennis

Articles

Introduction:

Virtual reality (VR) systems have evolved significantly over the past decade, enabling immersive experiences with enhanced realism and interactivity. This has motivated an interest in socially oriented applications. As user proxies, Virtual Humans (VHs) play essential roles in such applications. However, despite technological advancements, achieving realistic, expressive, and socially responsive VHs continues to present design and implementation challenges. In this scoping review, we present the state-of-the-art of VR VHs, examining the impact of VHs on the user experience.

Methodology:

We reviewed 59 papers retrieved from five databases across three core themes: the implementation and impact of VH facial expressions, …

Deep Learning Based Control System For Multi-Zone Hvac Residential Buildings, Mohammad H. Z. Alghalayeeni

Mechanical Engineering Theses

Heating, ventilation, and air conditioning (HVAC) systems are major contributors to residential energy consumption. However, most homes continue to rely on single zone thermostat control, which regulates temperature based on a single sensor and cannot account for thermal variations across multiple rooms. This often leads to uneven thermal conditions and inefficient energy use in multi-zone residential buildings. This thesis presents a deep reinforcement learning based approach for improving HVAC zoning control through dynamic airflow distribution. A physics based multi zone thermal model of a residential house was developed to simulate heat transfer processes including conduction, convection, solar and internal heat …

Aiw26s: Prompt Engineering, Ila Lama

Paul English Applied Artificial Intelligence (AI) Institute Publications

This workshop introduced participants to prompt engineering and how to effectively communicate with AI systems. Led by Ila Lama, the session covered key strategies such as defining goals, providing examples, setting constraints, and refining prompts to improve AI-generated outputs.

Participants explored applications of AI across domains, including education, business, and social media, while also discussing responsible AI use. The workshop emphasized that strong prompt design leads to more accurate, structured, and useful results, and that AI should be used to enhance human creativity and decision-making.

Ai-Scm Cmm: A Capability Maturity Model For Artificial Intelligence Integration In Supply Chain Management, Lordt Becklines, Omar F. El-Gayar, Patti Brooks, Insu Park

Annual Research Symposium

Artificial intelligence is increasingly deployed in supply chain management, yet many organizations struggle to align adoption efforts with process readiness, data quality, governance, and workforce capabilities, and they still lack validated supply chain specific roadmap for assessing readiness, sequencing investments, and reducing implementation risk. This study develops and evaluates a Capability Maturity Model for Artificial Intelligence Integration in Supply Chain Management to address that gap. Using a design science research approach, the study synthesizes prior literature and practitioner knowledge to define maturity dimensions, capability indicators, and staged progression levels for AI integration in supply chain contexts. The artifact and assessment …

Sprinkler Package Runoff Risk Tool For Center Pivot Irrigation Systems, Will Bowers

Spring Runoff Conference

Center pivots in Utah 

• 403,524 acres = 67% of sprinkler irrigated fields in the open in Utah 
• Considered one of the most effective sprinkler systems available with technological advancements over the years

Evaluating Alternative Water Conservation Scenarios For Alfalfa In The Great Salt Lake Basin Using Integrated Climate Model Projections, Saddy Pineda-Castellanos, Masoumeh Hashemi

Spring Runoff Conference

Elevation of Great Salt Lake North and South Arms (1903-2026)

An Estimation Of Crop Evapotranspiration Using Soil Water Balance In Vineyards, Tarique Aziz, Burdette Barker, Michael Caron, Michael Pace

Spring Runoff Conference

Breakout Session presentation given at the 2026 Spring Runoff Conference

Immersive Modeling To Generate Holistic Strategies To Get More Water To Great Salt Lake, Hadia Akbar

Spring Runoff Conference

How to get more water to GSL?

Must Address

• Complex water rights
• Competing water needs
• Historical legacies
• Variable and arid hydrology
• Infrastructure limitations and opportunities
• Lack of trust

What Makes Smart Irrigation Work? Lessons From Producers In The Upper Colorado River Basin, Tejinder Singh, Matt Yost, Elisa Flint, Burdette Barker, Jessica Ulrich-Schad, Silas Ekadu

Spring Runoff Conference

Colorado River Basin Water Crisis

• Water allocations in the Colorado River Basin were set during wetter periods and now exceed current river flows, creating a gap between water supply (12.5 maf yr^-1) and demand (15 maf yr^-1).
• River flow has declined 19% since 2000.

Making Water Visible: Neutral, Verification-First Infrastructure For Basin-Scale Water Accountability, Eric Mcculley

Spring Runoff Conference

Every Tool Tells You What the Lake Level WAS.

None Tell You What It WILL BE.

• Current monitoring is retrospective — USGS gauges and DWR reports show only historical data
• Decision lag: By the time you see the problem, it’s too late to adjust
• 2024–2025 season: GSL dropped to record lows before upstream conservation kicked in
• Agricultural users, municipalities, and GSL all compete for limited supply with imperfect information

Leasing Water For Great Salt Lake: Water Savings And Producer Impacts, Conner Harwood

Spring Runoff Conference

Great Salt Lake Water Leasing

• Utah is working to increase inflows to GSL through voluntary water leasing from agriculture
• But key information is missing:
• How much water can leases save at the field level?
• At what price should farmers be compensated?
• This project:

1. Estimates field-level consumptive water use
2. Estimates the value of water in agricultural production
3. Evaluates water savings and producer impacts across leasing strategies

Meteorological Monitoring With Real-Time Data Processing Using Uas, Htoo Poe Sar, Cal Coopmans, Sierra Young

Spring Runoff Conference

Background and Motivation 

• Agricultural water management requires information about crop water use and water consumption 
• Remote sensing methods are used to model and estimate environmental processes – but they require weather data 

Utah Prototype For Visualizing Vulnerabilities Downstream Of Dams, Courtney Flint, Michael Englert, Nicolas Holden

Spring Runoff Conference

The climate question 

• Overtopping = 1/3^rd of all dam failures (ASDSO) 
• Drought concerns and supply uncertainty motivate keeping reservoirs full 
• Overtopping likelier if extreme storm when reservoir full 
• Over much of the country the probability of the annual daily maximum rainfall > 100-year event and the preceding 30-day rainfall >10-year event are going up (Hwang & Lall 2024) 

The Reform Of Prior Appropriation And The Fate Of Great Salt Lake, Christopher L. Lant, Rocky Seeley, Beth Parker, Andrew Follett

Spring Runoff Conference

Legal Issues Raised by the Decline of Great Salt Lake

• Violations of Clean Air Act from dust threaten federal intervention
• Petition to list Wilson’s Phalarope as an endangered species

Nutrient Inputs, Crop Removal, And Residual Soil Nitrogen Under Automated Surge Irrigation In Northen Utah, Ngoni Mufute

Spring Runoff Conference

Introduction

• Increasing pressure on already water scarce resources due to

• Climate Change and or variability

• Increasing demand and competition for water. E.g. due to -urban expansion

• Environmental concerns (Especially concerning the Great Salt Lake (GSL)-

• the shrinking of water levels in the GSL,

• increasing pollution levels in the GSL and

• the impact of these issues on industry,

• dust from the drying lakebed,

• increasing threat to both aquatic life and land animals

The Physical, Legal, And Modeling Infrastructure For Water Resource Management Has Reached A Tipping Point, Paul Brooks

Spring Runoff Conference

Addressing these challenges requires improved predictions of water supply