Engineering Commons^™

Furniture Mover, Zachariah Burkhardt, Gary Mucciarone, Gino Mucciarone, Juan Soto, David Kotyk

Williams Honors College, Honors Research Projects

The movement of furniture is an often overlooked pain point for physically-challenged individuals, especially when rearranging furniture in a room. These individuals may try to minimize the risk of tip-over or strain-related injuries by seeking assistance from others. Still, some individuals are limited in finding volunteers forthcoming and capable of helping. This can lead to a dilemma of either being able to find individuals willing to assist in the process or risking one’s own personal safety when moving furniture. The proposed design project implements the use of multiple, independent platforms with mecanum wheels placed underneath each corner of a piece …

Beeswax Wraps As An Alternative To Single-Use Plastics, Sarah Skiver

Williams Honors College, Honors Research Projects

The project goal was to compare the food storage efficacy of sustainable beeswax wraps verses the single-use plastic methods of resealable plastic sandwich bags and plastic cling wrap. The goal was also to test the reusability of the beeswax wraps, as it is a key advantage of beeswax wraps that is advertised. The project purpose was to explore sustainable and eco-friendly alternatives to single use plastics, which are harmful to the environment in both their production and their disposal. Food spoilage was compared in beeswax wrap, plastic sandwich bags, and plastic cling wrap, and spoilage was also observed in a …

Structural Design And Application Of Polymeric Silicon Elastomers, Jacob Wyant

Williams Honors College, Honors Research Projects

The purpose of this project was to determine how the polymeric structure and mechanical properties of this elastomer are affected by the ratio between the polydimethylsiloxane macromolecular chains and the crosslinkers. These were determined via tensile and compression testing. Then, spiropyran was added to observe how this fluorescence and crosslinking agent affected the elastomer. Also, the elastomer’s fluorescent and icephobic nature were tested. The elastomers with a higher ratio of crosslinker to macromolecular chain could withstand higher tensile and compressive strains but failed at lower stresses than their counterparts with lower concentrations of crosslinkers. The elastomers were also found to …

Development Of A Regeneratively Cooled Liquid Rocket Engine, Dillon Petty, Nicole Zimmerli

Williams Honors College, Honors Research Projects

An additively manufactured (AM) liquid rocket engine, consisting of an injector, combustion chamber, and nozzle, was designed and printed using state-of-the-art methods and materials. The parts were manufactured using laser powder bed fusion. Additive manufacturing allowed for complex geometries and features, such as printing manifolds onto the components with a reduced number of parts. Additive, regenerative cooling channels were designed into the chamber and nozzle to allow for long-duration steady-state operation.

The feed system for the engine was designed and built to allow for pressure-regulated and steady-state testing. Tanks for the fuel and oxidizer were designed and built for a …

Quadcopter Airfoil Analyses, Isabella Allen, Nicholas Tolson, Trevor Mccaffrey

Williams Honors College, Honors Research Projects

This project focuses on the aerodynamic analysis of airfoils for quadcopter applications, aiming to optimize the performance of quadcopters through the selection and analysis of various 3D printed airfoil profiles. Quadcopters are unmanned aerial vehicles with four rotors arranged in a symmetric configuration. Each diagonal pair rotates in the same direction, allowing the offset to ensure the quadcopter remains level. The airfoil selection is crucial as it impacts aerodynamic performance, stability, and efficiency. The parameter of interest in these airfoils is maximum thrust and settling thrust produced, along with material wear of the propellers themselves. The testing of thrust production …

Implementing Systems Engineering Practices To The Zips Aero Design Team, Kaitlyn Bebb, Ariel Bryan

Williams Honors College, Honors Research Projects

The Zips Aero Design Team is a college sponsored design team that competes each year through the American Institute of Aeronautics and Astronautics (AIAA) Design Build Fly (DBF) competition. The rules generally consist of 3 differing flight missions and a ground mission, with overarching requirements such as size, takeoff distance, and battery limitations. A complex set of rules such as these is meant to be difficult for even the best of teams to master, especially without proper organization and project management. This senior design report outlines the benefits of implementing systems engineering to the Zips Aero Design Team, through multiple …

Surface Preparation Study, Ryan Ferguson

Williams Honors College, Honors Research Projects

This work explores a custom air atmospheric pressure plasma treatment (APPT) machine’s effectiveness in cleaning and chemically activating a CFRP surface. It is explore by implementing water contact angle (WCA) measurements, water-break free (WBF) testing, and adhesive tubular lap-joint (TLJ) tensile testing. An 8x3 test matrix of different machine parameters is defined with the bounding conditions being the machine’s capabilities and industry standard recommendations. Each configuration of the test matrix is explored after treatment at multiple time intervals up to 2 weeks afterwards to gain insight into the outlife of the treatments with the intention of adhesively bonding to the …

Human Tracking Function For Robotic Dog, Andrew Sharkey

Williams Honors College, Honors Research Projects

With the increase the increase in automation and humans and robots working side by side, there is a need for a more organic way of controlling robots. The goal of this project is to create a control system for Boston dynamics robotic dog Spot that implements human tracking image software to follow humans using computer vision as well as using hand tracking image software to allow for control input through hand gestures.

The Passing Board, John Fitzgerald

Williams Honors College, Honors Research Projects

For my Honors Research Project I am taking a more personal route and looking to solve a childhood question/issue by designing a board that is small and easy to transport while also giving the best bounce pass possible. My proposed project would be a board that a soccer player can play a bounce pass onto and receive the ball from. The base of this design sounds simple enough, however, I would like to implement a way that the board can be adjusted to alter the angle of return of the soccer ball after the bounce. I also want to design …

The Impact Distracted Driving Has On Fatal Crashes, Adam Pohrte

Williams Honors College, Honors Research Projects

Distracted driving has been a major problem in the United States and around the globe for quite some time. It is one of the leading causes of fatal car crashes, and its impact on road safety has been the subject of much research and debate. The purpose of this paper is to focus on the driver who was distracted that ended up causing the crash. To obtain precise data and results, all the information about these crashes is from the Fatality Analysis Reporting System (FARS). FARS is a nationwide census maintained by the National Highway Traffic Safety Administration (NHTSA) that …

Powering Electric Vehicles: Are We Ready?, Christian Yoder

Williams Honors College, Honors Research Projects

This project will investigate typical power grids and the impacts that electric vehicles have on them. Electric vehicles are rapidly growing in popularity and much of the world is promising to make the switch from combustion engines to EVs. Electric vehicles demand a large amount of electricity. With fast charging becoming available, it is worth asking if the current electrical infrastructure can handle the increase in demand. After talking to a source at FirstEnergy, it seems large electric companies are well aware of areas in need of adjustment and are moving accordingly.

Botsitter, Maria Hatzis, Gregory Blondheim Jr., Marian Bonto, Brett Jacobsen

Williams Honors College, Honors Research Projects

As society progresses into an era where both parents work, whether it is online or in person, children in the home may be put in dangerous situations if they are not given the attention they need. The BotSitter is an automated system that follows the child around and makes an audio alarm to alert both the child and the nearby guardian. Using RSSI trilateration, predetermined danger areas, and embedded controls, the BotSitter will be able to follow the child. The device can manage to keep track of the child for the guardian while being almost completely automated outside of setup.

Teflon Replacement In Pans, Teodora Neamtu

Williams Honors College, Honors Research Projects

The purpose of the project is to determine an optimal prepping method of common cooking oils for pans that will be as effective as Teflon non-stick pans. The reason for this is to replace Teflon coating in pans, which can be very toxic for humans and the environment. Teflon has been a common coating for non-stick surfaces that is useful when cooking things such as eggs. To determine an optimal cooking method, three different oils were used: olive oil, vegetable oil, and shortening. The oils were tested on an aluminum pan by cooking egg whites at various temperatures, cooking times, …

Cost-Benefit Analysis Of Increased Water Treatment Plant Service Goals On Reducing Water Quality Risk, Briton Polen, Kendra Sanner

Williams Honors College, Honors Research Projects

To treat water to make it safe to drink, disinfection processes are used in water treatment plants. These disinfection processes produce disinfection byproducts (DBPs) through the reaction of organic matter and the disinfectant, such as chlorine. DBPs have been shown to pose a cancer risk to consumers. In this report, the focus is on two types of DBPs, trihalomethanes (THMs) and haloacetic acids (HAAs). The cancer risks associated with DBPs are analyzed through ingestion and inhalation pathways. Ingestion and inhalation consist of common water uses like drinking, cooking, or bathing. In addition to this, DBPs have been shown to increase …

Mouthpiece For Patients With Neuromuscular Disorders, Rebekah Starkey, Carissa Thompson, Michael Dickens, Andrew Pero

Williams Honors College, Honors Research Projects

Neuromuscular Disorders (NMDs) impact people throughout the world. An early hallmark of these disorders includes some degree of facial muscle weakness. Respiratory testing is important to evaluate the progression of these patients’ NMDs. However, these tests require that the patient purses their lips around a mouthpiece to create a tight seal. This is a difficult task for one with facial muscle degeneration. This often leads to results that fail to reflect the patient’s true respiratory ability and prevents their physician from providing the appropriate degree of care. The objective of this project was to develop a face mask or mouthpiece …

Intergranular And Pitting Corrosion Mechanisms Of Sensitized Aluminum Alloy Aa5083, Clayton Egleston

Williams Honors College, Honors Research Projects

The motivation and objectives of this project is to examine the mechanisms of intergranular corrosion (IGC) and pitting corrosion of sensitized AA5083. In this regard, different characterization techniques were used, including optical analysis of microstructure, cyclic potentiodynamic polarization with Tafel fitting, electrochemical impedance spectroscopy with electrical equivalent circuit (EEC) fitting, and potentiostatic current transient monitoring. The transition from IGC to pitting corrosion occurs when the grain boundaries become saturated with the β-phase (Mg₂Al₃). It was found that AA5083 becomes more vulnerable to pitting corrosion as the degree of sensitization increases.

Growing In Stem: Hands-On Education Via Tower Gardening, Jeffrey A. Nowak, Shelby Johnston-Werling

Indiana STEM Education Conference

Sole use of a textbook as the primary source of learning in the middle school setting has been linked to potentially limit students’ conceptual understanding of complex content (Driscoll et al., 1994), while the positive impact of hands-on learning has been well documented (Ekwueme et al., 2015; Satterthwait, 2010). Ideally, when a textbook is used in conjunction with content applied in a hands-on manner, student engagement and understanding of standards-based content are increased. In a grant funded collaboration between the Northeast Indiana STEM Education Resource Center housed at Purdue University Fort Wayne and an East Allen Community Schools middle school …

Impact Of Lubricant In The Performance Of Variable Speed Heat Pumps Working With R290, Rubén Ossorio, Emilio Navarro-Peris, Riley Barta

School of Mechanical Engineering Faculty Publications

Modulating the speed of the compressors and adapting its capacity to the required load has led to a decrease in the annual energy consumption in many applications. However, in the compressor, having adequate lubrication at low speeds usually implies discharging too much lubricant at higher speeds. Although necessary for compressor operation, lubricating oil acts as a contaminant in the rest of the system. Consequently, manufacturers have to consider the oil circulation rate (OCR), as it limits the speed range of the compressor. In a previous study, a compressor was tested over its speed range (30 – 110 Hz), working with …

Improving Developers' Understanding Of Regex Denial Of Service Tools Through Anti-Patterns And Fix Strategies, Sk Adnan Hassan, Zainab Aamir, Dongyoon Lee, James C. Davis, Francisco Servant

Department of Electrical and Computer Engineering Faculty Publications

Regular expressions are used for diverse purposes, including input validation and firewalls. Unfortunately, they can also lead to a security vulnerability called ReDoS (Regular Expression Denial of Service), caused by a super-linear worst-case execution time during regex matching. Due to the severity and prevalence of ReDoS, past work proposed automatic tools to detect and fix regexes. Although these tools were evaluated in automatic experiments, their usability has not yet been studied; usability has not been a focus of prior work. Our insight is that the usability of existing tools to detect and fix regexes will improve if we complement them …

An Empirical Study Of Pre-Trained Model Reuse In The Hugging Face Deep Learning Model Registry, Wenxin Jiang, Nicholas Synovic, Matt Hyatt, Taylor R. Schorlemmer, Rohan Sethi, Yung-Hsiang Lu, George K. Thiruvathukal, James C. Davis

Department of Electrical and Computer Engineering Faculty Publications

Deep Neural Networks (DNNs) are being adopted as components in software systems. Creating and specializing DNNs from scratch has grown increasingly difficult as state-of-the-art architectures grow more complex. Following the path of traditional software engineering, machine learning engineers have begun to reuse large-scale pre-trained models (PTMs) and fine-tune these models for downstream tasks. Prior works have studied reuse practices for traditional software packages to guide software engineers towards better package maintenance and dependency management. We lack a similar foundation of knowledge to guide behaviors in pre-trained model ecosystems.

In this work, we present the first empirical investigation of PTM reuse. …

Teachers' Instructional Strategies In Integrated Stem Education, Yousef Alrashdi, Paul A. Asunda

Indiana STEM Education Conference

Integrated Science, Technology, Engineering, and Mathematics (iSTEM) education has been regarded as a model that provides students with skills necessary for future careers and enhances the economy of nations. Although there is a considerable body of research on the effective educational approaches in iSTEM education including problem-based and project-based learning, the ways teachers implement these approaches remain ambiguous due to a paucity of consensus about how to effectively use iSTEM approaches in classrooms (Thibaut et al., 2018). Additionally, there is a need for further investigation to understand teachers’ instructional strategies and practices in iSTEM education (Bush, 2019). To fulfill this …

Integrated Stem: Impact Of Engineering Design And Computer Science In Stem Labs, Jason Morphew, Ruben Lopez, Amir Bralin, Ravishankar Chatta Subramaniam, Sanjay Rebello, Carina Rebello

Indiana STEM Education Conference

By integrating physics laboratories with engineering design and computer science, students apply physics principles to ill-structured and complex problems, engage in knowledge transfer, and gain interest in STEM. The introductory physics labs at Purdue have been updated to include engineering design and computer science principles that ground physics in authentic problems. Integrated labs have been evaluated using student perception post-surveys, student course performance, interviews, and case-study observations. Preliminary results indicate that integrated physics labs promote transfer, enhanced metacognitive skills, student interest, and motivation.

Engineering Technology Programs And Technical Standards: Investigating Library Access And Course Integration, Margaret Phillips, Paul B Mcpherson, Danielle Leclerc

Libraries Faculty and Staff Scholarship and Research

Due to ABET accreditation requirements and industry expectations, integrating technical standards into Engineering Technology (ET) curricula is crucial for student success. However, previous studies have shown that faculty report access and knowledge challenges in working to integrate standards into ET course content. Additionally, academic librarians have long acknowledged there are many issues with providing access to standards to campus users, such as high costs and extensive digital rights management (DRM) restrictions. The purpose of this study is to conduct an environmental scan of library websites at institutions with ET programs to investigate library-provided access to standards and to survey ET …

Data Quality Checking Guide, Wei Zakharov

Libraries Faculty and Staff Scholarship and Research

A data quality checking guide has been developed to facilitate undergraduates on the critical aspects of data quality assessment. The goal is to become competent data consumers and data generators as well. This checking guide encompasses six fundamental dimensions: Data Credibility, Timeliness, Information Completeness, Data Accuracy, Data Consistency, and Data Deduplication. These dimensions are frequently cited in scholarly references on data quality. Each dimension plays a crucial role in ensuring the reliability and usability of data. Scenarios of students' work are also discussed.

Innovation In Quantum Pedagogy, Application, And Its Relation To Culture (Iqparc), Zeynep Gonca Akdemir, Dongyang Li, Muhsin Menekse, Mahdi Hosseini, Erica W. Carlson, Nicholas Dang

Indiana STEM Education Conference

Innovation in Quantum Pedagogy, Application, and its Relation to Culture (IQ-PARC) is a team of Purdue faculty, graduate, and undergraduate students who collaborate and work for the National Defense Education Program (NDEP) for Science, Technology, Engineering, and Mathematics (STEM) education, outreach, and workforce initiative programs. We promote a STEM-literate workforce by providing learning opportunities for youth to understand basic principles and applications of quantum concepts through a variety of both face-to-face and online activities. This research brief describes accomplished tasks in the K-12 education space (e.g., quantum-infused middle school curriculum unit) and shares upcoming plans within the project timeline.

Wave-Powered Batch Reverse Osmosis Buoy, Austin Howse, Camden Frieling, Cooper Ford, Imaan Qazilbash, Joel Veihl, Mariya Savchenko, Ryan Vulich, Sultan Alnajdi, Abhimanyu Das, Antonio Esquivel-Puentes, Ali Naderi Beni, David M. Warsinger, José Garcia-Bravo

School of Mechanical Engineering Faculty Publications

As populations grow across the world, the availability of freshwater at a reasonable cost has become a growing concern to many nations. An estimated 1.1 billion people do not have access to safe drinking water [5]. Many of these areas also exist in coastal communities which get burdened by severe weather storms. During these occasions, access to clean drinking water drastically decreases. Combining this with the potential for ocean energy, access to clean drinking water can be derived with a potential solution. The ocean contains abundant resources that comprise of untapped wave-powered energy, unharvested salt water to be turned potable, …

Studies On Non-Transition Metal Substitution To Ab2 Metal Hydride Alloys For Battery Application, Shiuan Chang

Wayne State University Dissertations

Nowadays, multiphase transition metal-based AB2 metal hydride alloys and the rare-earth metal-based AB5 alloys (currently used in consumer NiMH batteries) are used as negative electrodes in NiMH batteries. It is of great interest to explore the possibility of significantly improving NiMH battery performance to compete with Li-ion batteries. In this area, the effect of dopant elements from Group-IA, -IIA, -IIIA non-transition metal family has not been thoroughly studied. In this study, lithium, magnesium, and boron (a metalloid considered metal in this study) were chosen as modifiers in the C14-phase predominant AB2 alloy by different dopant concentrations and synthesis methods, doping …

Data Driven Method To Assess Safety And Energy On Freeway And Intersection Performance Using Probe Vehicle, Rezwana Kabir

Wayne State University Dissertations

Traffic congestion in cities is becoming a more pressing issue as travel demand increases, leading to safety and mobility problems and wasteful use of vehicle energy. Both freeways and signalized corridors are important in creating an efficient transportation network, and congestion on these infrastructure types presents a significant mobility concern in the United States. With advances in sensing technologies for intelligent transportation systems, probe vehicles equipped with GPS-enabled devices such as cell phones and in-vehicle telematics or navigation systems are increasingly being used to gather more information about traffic conditions. While fixed point detectors can be limited by their geographical …

Optical Diagnostics Of Hydrocarbon Fuel Autoignition Using The Corrected Filtered Natural Emission Of Species Technique, Maysam Molana

Wayne State University Dissertations

The gas temperature and concentration of carbon monoxide and carbon dioxide of a hydrocarbon fuel mixture were measured using a rapid compression machine by applying a modern optical diagnostics methodology called the corrected filtered natural emission of species (C-FNES) technique. This technique uses a correction factor that includes all of the experimental and simulation errors and uncertainties into the measurements. To ensure the robustness of the proposed technique, the effect of temperature and pressure on the measured data was investigated extensively. To this end, a pentane inert mixture was tested in a wide range of operation conditions: six compressed gas …

Initiating Change In Care: Socially Assistive Robots, Sooraj Sushama

Theses and Dissertations

Socially assistive robots (SAR) are autonomous machines equipped with sensors and software that allow them to interact socially with humans. SAR robots are commonly used in healthcare settings to provide patients with non-clinical support, such as conversation and emotional companionship. SARs can also deliver reminders, monitor vital signs, and provide educational information about health conditions or medications. Researchers have studied SAR applications in detail. Additionally, there has been prior research on SAR where users' sociodemographic factors and technology acceptance were studied. But even though the backbone of SAR is an advanced technology, no known research has been done on users' …