Engineering Commons^™

A Comprehensive Review Of Dc-Dc Converters For Ev Applications, Shayan Hosseinzad, Amin Mirzaei

Emirates Journal for Engineering Research

DC-DC converters in Electric vehicles (EVs) have the role of interfacing power sources to the DC-link and the DC-link to the required voltage levels for usage of different systems in EVs like DC drive, electric traction, entertainment, safety and etc. Improvement of gain and performance in these converters has a huge impact on the overall performance and future of EVs. So, different configurations have been suggested by many researches. In this paper, bidirectional DC-DC converters (BDCs) are divided into four categories as isolated-soft, isolated-hard, non-isolated-soft and non-isolated-hard depending on the isolation and type of switching. Moreover, the control strategies, comparative …

Fabric-Based Organic Electrochemical Transistor Towards Wearable Ph Sensing Electronics, Nestor Osvaldo Marquez Rios

USF Tampa Graduate Theses and Dissertations

Wearable electronics interest has attracted the attention of a few sectors because of their applicability in different areas like healthcare, military, and our daily basis. Still building circuits on fabrics to make these wearable electronics is challenging. As transistors are the building blocks of electronic circuits and most of the biosensors, recently, fiber-shaped electrochemical transistors have been studied extensively for a lot of applications including bioelectronics. Fiber-based devices are getting popular in different applications due to their low fabrication cost, lightweight, and flexibility without losing their properties. Additionally, they are potentially suitable for making sensors on garments.

In this work, …

Computational Fluid Dynamics Modeling Of A Wafer Etch Temperature Control System, Henrique Oyama, Kip Nieman, Anh Tran, Bernard Keville, Yewei Wu, Helen Durand

Chemical Engineering and Materials Science Faculty Research Publications

Next-generation etching processes for semiconductor manufacturing exploit the potential of a variety of operating conditions, including cryogenic conditions at which high etch rates of silicon and very low etch rates of the photoresist are achieved. Thus, tight control of wafer temperature must be maintained. However, large and fast changes in the operating conditions make the wafer temperature control very challenging to be performed using typical etch cooling systems. The selection and evaluation of control tunings, material, and operating costs must be considered for next-generation etching processes under different operating strategies. These evaluations can be performed using digital twin environments (which …

Peer Review Of Teaching: Et Theory, Deficit Irrigation And Consumptive Use, Derek M. Heeren, Saleh Taghvaeian

Department of Agricultural and Biological Systems Engineering: Presentations and White Papers

A BSE Peer Review of Teaching was carried out for a graduate level course on Advanced Irrigation Management. This course has been offered for several years; each time improvements are made, but there is always a need for additional improvement. In particular, ET theory, deficit irrigation, and consumptive use are topics that the students struggle to grasp. These topics involve a relatively high level of math for an MS-level (800-level) Agricultural Systems Technology course, and the available materials on these topics either were not well developed or were not a good fit for this class. The primary objective was to …

Resource Recovery From Crew Metabolic Wastes In Lunar And Martian Habitats: Reuse Of Effluent From An Anaerobic Membrane Bioreactor Treating Fecal Organic Matter As Fertilizer Source For Plants, Alexandra A. Smith

USF Tampa Graduate Theses and Dissertations

As humans set their sights on exploration of the Moon and Mars human focused challenges like providing potable water, supplying nutritious food to the astronaut crew, and managing their waste present themselves. There are no readily available resources on the Moon and Mars, therefore nothing should be considered unusable including the organic wastes (i.e., feces and urine) produced by the crew. Fecal matter is not currently recycled and is treated as solid waste. After collection, it is discarded out of the International Space Station where it is incinerated upon re-entry. This approach will not work on the Moon’s surface. There …

Anaerobic Digestion Of Brewery Waste Including Spent Yeast And Hops, Dhanashree Rawalgaonkar

USF Tampa Graduate Theses and Dissertations

Florida is home to more than 300 craft breweries, that brew over a million barrels of beer annually. Brewing is an energy intensive process and produces large quantities of high strength waste including spent grains, yeast, hops, and high strength wastewater. Brewery wastewater, and spent yeast have high Chemical Oxygen Demand (COD) concentrations between 5000 mg/L – 10,000 mg/L, and 200,000 mg/L – 300,000 mg/L respectively. Brewery effluent wastewater is sent to Publicly Owned Treatment Works (POTWs) which implement high surcharges based on the strength of brewery effluent (COD concentration). While some of the spent yeast and hops can be …

Optimal Estimation Inversion Of Ionospheric Electron Density From Gnss-Pod Limb Measurements: Part I-Algorithm And Morphology, Dong L. Wu, Nimalan Swarnalingam, Cornelius C. J. H. Salinas, Daniel J. Emmons, Tyler C. Summers, Robert Gardiner-Garden

Faculty Publications

GNSS-LEO radio links from Precise Orbital Determination (POD) and Radio Occultation (RO) antennas have been used increasingly in characterizing the global 3D distribution and variability of ionospheric electron density (Ne). In this study, we developed an optimal estimation (OE) method to retrieve Ne profiles from the slant total electron content (hTEC) measurements acquired by the GNSS-POD links at negative elevation angles (ε < 0°). Although both OE and onion-peeling (OP) methods use the Abel weighting function in the Ne inversion, they are significantly different in terms of performance in the lower ionosphere. The new OE results can overcome the large Ne oscillations, sometimes negative values, seen in the OP retrievals in the E-region ionosphere. In the companion paper in this Special Issue, the HmF2 and NmF2 from the OE retrieval are validated against ground-based ionosondes and radar observations, showing generally good agreements in NmF2 from all sites. Nighttime hmF2 measurements tend to agree better than the daytime when the ionosonde heights tend to be slightly lower. The OE algorithm has been applied to all GNSS-POD data acquired from the COSMIC-1 (2006–2019), COSMIC-2 (2019–present), and Spire (2019–present) constellations, showing a consistent ionospheric Ne morphology. The unprecedented spatiotemporal sampling of the ionosphere from these constellations now allows a detailed analysis of the frequency–wavenumber spectra for the Ne variability at different heights. In the lower ionosphere (~150 km), we found significant spectral power in DE1, DW6, DW4, SW5, and SE4 wave components, in addition to well-known DW1, SW2, and DE3 waves. In the upper ionosphere (~450 km), additional wave components are still present, including DE4, DW4, DW6, SE4, and SW4. The co-existence of eastward- and westward-propagating wave4 components implies the presence of a stationary wave4 (SPW4), as suggested by other earlier studies. Further improvements to the OE method are proposed, including a tomographic inversion technique that leverages the asymmetric sampling about the tangent point associated with GNSS-LEO links.

Research On Stability Of Rock Mass And +30 Level Surface Construction Works When Re-Exploiting The Seam H10 At Mong Duong Coal Mine, Vietnam, Tien Trung Vu, Doan Viet Dao

Journal of Sustainable Mining

The re-exploitation of coal seams located near the ground is one of the solutions to increase output, reduce mining investment costs, and avoid wasting coal resources. The re-exploitation of coal seams will also cause instability of the surrounding rock mass and may affect surface construction works. Through the process of re-exploiting the longwall in seam H10 at Mong Duong Coal Mine, the authors have studied and evaluated the stability of the rock mass and +30 level surface works (including fan station and gateroad). To achieve the results in this study, the numerical simulation model method and the analytical method were …

Keynote: "Witron", Daniel Ries

International Material Handling Research Colloquium

No abstract provided.

Evaluating The Post-Mining Land Uses Of Former Mine Sites For Sustainable Purposes In South Africa, Sphiwe E Mhlongo

Journal of Sustainable Mining

This paper uses a case study of an abandoned magnesite mine in the Limpopo Province of South Africa to find ways of identifying post-mining land used from the current uses of the abandoned mine sites or features. The approach used involved carrying out a field characterization of the mine site and documentation of the current uses of the features of the abandoned mine site. The technique used to identify the internal and external factors of the land uses involved analyzing their Strength, Weakness, Opportunities, and Threats. The Analytic Hierarchy Process (AHP) technique was used for further ranking of the land …

Reasons Why Oil Reserves Remain Unproductive-A Case Study, Mohamed Al-Saho

Journal of the Arab American University مجلة الجامعة العربية الامريكية للبحوث

By studying the production plans of some wells of Al Furat Petroleum Company, the researcher noticed that the rate of production increases to reach a peak and then falls back sharply. The deformation of the area around the well due to the decrease in the formation pressure (after production for a certain period) may have caused a change in the storage properties (porosity, permeability) and thus lower production rate. However, from the point of view of the geomechanics of the oil formation, which includes the study of the stress situation and its effect on the rock tissue, we will notice …

Identify The Most Productive Crop To Encourage Sustainable Farming Methods In Smart Farming Using Neutrosophic Environment, Ahmed Abdelhafeez, Hadeer Mahmoud, Alber S. Aziz

Neutrosophic Systems with Applications

Only with careful management can the data provided by crops be used to make smart, profitable choices. Data has become the central ingredient in contemporary agriculture, and the recent advancements in handling it are contributing greatly to the meteoric rise of smart farming. Gains in efficiency and longevity may be realized to a significant degree by using the objective data collected by sensors. These data-driven farms can maximize output while minimizing waste and environmental impact thanks to the information they collect and analyze. Various criteria and factors in smart farming can aid in productivity. Sensors, drones, Global Positioning System (GPS) …

Refill Friction Stir Fastener Repair In Aa7050-T7451, Andrew John Curtis

Theses and Dissertations

The majority of Refill Friction Stir Spot Welding (RFSSW) is used to join two materials together oriented in a lap joint configuration. In this study, RFSSW was investigated and tested using an unconventional configuration setup, a hole/plug insertion approach. RFSSW was tested as a means of repairing a cracked rivet hole due to excessive use conditions. This was done by inserting a plug into a hole and using the RFSSW process to bond the plug to the base material. Machine and tool limits were investigated to determine if a refilled plug repair was possible and if complete mixing between plug/hole …

Identify The Most Productive Crop To Encourage Sustainable Farming Methods In Smart Farming Using Neutrosophic Environment, Ahmed Abdelhafeez, Hadeer Mahmoud, Alber S. Aziz

Neutrosophic Systems with Applications

Only with careful management can the data provided by crops be used to make smart, profitable choices. Data has become the central ingredient in contemporary agriculture, and the recent advancements in handling it are contributing greatly to the meteoric rise of smart farming. Gains in efficiency and longevity may be realized to a significant degree by using the objective data collected by sensors. These data-driven farms can maximize output while minimizing waste and environmental impact thanks to the information they collect and analyze. Various criteria and factors in smart farming can aid in productivity. Sensors, drones, Global Positioning System (GPS) …

Cesium Voltilization In Lif-Bef2: Predicting Release In The Event Of Fhr Fuel Failure, Johnny Hedrick Williams

Theses and Dissertations

This work demonstrates how ICP-MS can be employed to evaluate cesium volatilization from LiF-BeF2 (Flibe) salt with ab initio molecular dynamics studies used as corroborating data to better understand cesium behavior. Using mixtures of Flibe with 2 mol% CsF, it was found that cesium was stable within the salt melt at temperatures between 500-650°C over a time span of 8 hours. At 800°C, cesium vaporized from the salt at a rate of 0.83% / hr with a mass flux of 0.0023 g Cs / cm2hr. The atomistic modeling results show poor solvation of Cs at 500°C and 800°C, with stability …

Exploring Alternative Electron Donors For Heterotrophic Denitrification At A Water Reclamation Facility In Tampa Bay, Tejas Athavale

USF Tampa Graduate Theses and Dissertations

An excess of nitrogen in water can pose problems, ranging from algal blooms to creating toxic environments for marine life. Therefore, wastewater treatment plants need to remove nitrogen from wastewater during the treatment process. Biological nitrogen removal is one process these plants may use, which commonly involves nitrification and denitrification, converting nitrogen in the form of ammonia to nitrate, and then ultimately nitrogen gas. The process of denitrification often requires an electron donor, and methanol is a common choice. However, it is flammable, and therefore there is a need to explore alternative electron donors. Alternative donors can include manufactured chemicals …

Characteristics And Hydraulic Behavior Of Adsorptive Media For Use In Permeable Reactive Barriers, Shelby Rocha

USF Tampa Graduate Theses and Dissertations

The Cargill ditch is located on the property of Se7en Wetlands, a 1600-ac treatment wetland system in Lakeland, Polk County, Florida. The Se7en Wetlands property was previously utilized for phosphate mining prior to the construction of the system. Nonpoint nutrient sources derived from remnants of abandoned phosphate mines – known as “legacy phosphorus” – become mobilized by stormwater runoff and impair surface water bodies by promoting harmful algal blooms (HABs). Thus, the Cargill ditch likely conveys nutrient rich flow resulting from legacy phosphorus and is thought to be one contributing factor in the occurrence of HABs within the treatment wetland …

Concepts For The Use Of Knowledge-Based Engineering In Intralogistics System Planning, Christian Landschützer, Alexander Ortner-Pichler

International Material Handling Research Colloquium

No abstract provided.

5g Opportunities In Warehousing, Roshan George, Natalie S. Cherbaka, Kimberly Ellis

International Material Handling Research Colloquium

No abstract provided.

Robotic Bin-Picking: Benchmarking Robotic Grippers With Modified Ycb Object And Model Set, Tone Lerher, Primož Bencak, Darko Hercog, Boris Jerman, Luka Bizjak

International Material Handling Research Colloquium

No abstract provided.

An Efficient Milp Formulation For The Parallel-Load Retrieval In Puzzle-Based Storage Systems With Simultaneous Load Movements, Yossi Bukchin, Tal Raviv

International Material Handling Research Colloquium

No abstract provided.

Considerations When Designing An Autostore System, Russell D. Meller

International Material Handling Research Colloquium

No abstract provided.

Current Challenges And Approaches In Route Selection Of A Fleet Of Amr, Thorsten Schmidt, Karl-Benedikt Reith, Frank Schulze

International Material Handling Research Colloquium

No abstract provided.

Rcs/Rs Under Throughput Investigation, Georg Kartnig Prof., Philipp Trost, Michael Eder

International Material Handling Research Colloquium

No abstract provided.

Warehouse Robotization With Wheel.Me Genius: A Puzzle-Based Movable Racks System, Fabio Sgarbossa, Martin Amaral Halseide, Atle Timenes

International Material Handling Research Colloquium

No abstract provided.

Breakout Session B-1: "Industry 5.0", Jesus Jimenez, Uday Venkatadri

International Material Handling Research Colloquium

No abstract provided.

Breakout Session B-2: "Geopolitics", Md Sarder, Sunderesh S. Heragu

International Material Handling Research Colloquium

No abstract provided.

Breakout Session B-3: "Layouting", Sadan Kulturel-Konak, Anike Murrenhoff

International Material Handling Research Colloquium

No abstract provided.

Design Of Puzzle-Based Storage Systems With Unidimensional Cells, Hector J. Carlo, Andres Blanco

International Material Handling Research Colloquium

No abstract provided.

Perspectives On Automation For Omnichannel Services And The Need For New Robotic Solutions For Store Fulfillment Operations, Jennifer Pazour, Manmit Padhy, Georg Fischer, Joyjit Bhowmick, Sebastian Köhler, Gideon Arndt, Kai Furmans

International Material Handling Research Colloquium

No abstract provided.