Engineering Commons^™

Calibration Of The Johnson–Cook Model At High Temperatures For An Ultra-High Strength Crnimov Steel, Mario F. Buchely, S. Chakraborty, V. Athavale, Laura Bartlett, Ronald J. O'Malley, D. Field, K. Limmer, K. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a study on the thermo-mechanical behavior of an ultra-high strength CrNiMoV steel at high temperatures and medium strain rates through hot tensile tests. The material was examined in two conditions: as-cast/heat-treated (AC/HT) and as-rolled (AR). Tensile tests were conducted at temperatures of 800,900,1000,1100, and 1200°C, and strain rates of 0.1,1, and 10s−1. Inclusion and porosity analysis was also performed on the tensile specimens. The results revealed that the flow stress decreased by approximately 70% on average from 800°C to 1200°C, while increasing by approximately 32% on average from 0.1s−1 to 10s−1 in strain rate. The elongation exhibited …

Atomistic Simulations Of Twin Facets Associated With Three-Dimensional { []011 } Twins In Magnesium, Qiyu Zeng, Mingyu Gong, Houyu Ma, Yao Shen, Jian-Feng Nie, Jian Wang, Yue Liu

Department of Mechanical and Materials Engineering: Faculty Publications

Twinning is a deformation mechanism that creates three-dimensional (3D) twin domains through the migration of twin facets. This occurs via the nucleation and glide of twinning disconnections (TDs), which can pile up to create twin facets. A comprehensive under- standing of twin facets associated with 3D twins, including their atomic structures and energies, is crucial for understanding deformation twinning. In this study, we propose a molecular statics/dynamics (MS/MD) approach to determine characteristic twin facets enclosing 3D non-equilibrium/equilibrium { [] 011 } twin domains, which has been much less studied than the counterpart { [] 012 } twin domains. The stability …

The Essential Work Of Fracture In Peridynamics, Christer Stenström, Kjell Eriksson, Florin Bobaru, Stefan Golling, Pär Jonsén

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the essential work of fracture (EWF) method is introduced for a peridynamic (PD) material model to characterize fracture toughness of ductile materials. First, an analytical derivation for the path-independence of the PD J -integral is provided. Thereafter, the classical J -integral and PD J-integral are computed on a number of analytical crack problems, for subsequent investigation on how it performs under large scale yielding of thin sheets. To represent a highly nonlinear elastic behavior, a new adaptive bond stiffness calibration and a modified bonddamage model with gradual softening are proposed. The model is employed for two …

Mitigating Landslide Hazards In Qena Governorate Of Egypt: A Gis-Based Neutrosophic Paprika Approach, Nabil M. Abdelaziz, Safa Al-Saeed

Neutrosophic Systems with Applications

This paper presents a novel approach to landslide susceptibility assessment in the Qena Governorate, Egypt, integrating the neutrosophic Multi-Criteria Decision-Making (MCDM) method, the Potentially All Pairwise RanKings of all possible Alternatives (PAPRIKA), and the ArcGIS weighted overlay technique. The research focuses on the quantification and prioritization of eight criteria: slope, aspect, proximity to road, soil type, proximity to river, land cover, elevation, and Lithology. These factors are evaluated under the uncertainty and indeterminacy of the neutrosophic environment by employing the PAPRIKA method. The results of the analysis are visualized and interpreted using ArcGIS weighted overlay, offering spatially explicit insights into …

Local Chlorhexidine Delivery For Periodontal Infection Therapy: A Short Review, Muhammad Guruh Najmudin, Azizah Intan Pangesty, Rini Riastuti, Sunarso Sunarso, Abdul Halim Abdullah

Journal of Materials Exploration and Findings

Oral diseases affected more than half of the world’s population. Periodontitis is the second biggest threat to oral health after dental caries. Periodontitis is an inflammation inside periodontal pockets caused by pathogenic microbial colonies which lead to destruction of bone tissue and soft tissue. Chlorhexidine gluconate is an antimicrobial agent that effective to destroy pathogenic microbial and cure periodontitis. Chlorhexidine gluconate is given locally using a carrier material to the infected area. There are several materials that can be used to deliver Chlorhexidine gluconate to the infected periodontal tissue such as gel, liquid (mouthwash), and chip. This short review aims …

Optimization Of Alti Pld Coating By Increasing Ti Content, N2 And Annealing Which Used For Skd61 Pins In Aluminum Die Casting, Rusman Kosasih, Maria Margaretha Suliyanti Prof, Dedi Priadi, Wisnu Usni

Journal of Materials Exploration and Findings

The Alumunium Titanium Nitrogen (AlTiN) coating is known as one of the best coating materials for protective coating, while Pulsed Laser Deposition (PLD) is a laser coating process used for electric layer and superconductor applications, producing thin films up to 20 µm in thickness. The combination of these two matters has already been researched and is still in progress. One major challenge in the aluminium casting industry is to minimize the damage caused to tool steel pins made from SKD61, when aluminium material sticks to the pin, and halting production. Therefore, research on effective coatings for tool steels and testing …

Effect Of Heat Input On Microstructure And Mechanical Properties Of Submerged Arc Welded Sm570-Tmc Steel, Toni Yuhandri, Winarto Winarto, Diana Natalia

Journal of Materials Exploration and Findings

SM570TMC is high-strength steel (HSS), which is commonly used in structures that require higher-strength components. In this research, submerged arc welding (SAW)-welded SM570 TMC steels' microstructure and mechanical characteristics were examined. SM570 plates with 12mm thickness were multi-pass welded by using a 3.0 mm diameter of ESAB OK Autrod 13.40 (AWS A5.23: EG) filler metal. The joint design is a single V multi-pass butt weld with a backing strip. Two welded joints were prepared by using heat inputs of 2.2 and 2.9 kJ/mm. The microstructures of two welded joints were observed by using optical microscopy and scanning electron microscope (SEM). …

The Effect Of Current Density And Hard Chrome Coating Duration On The Mechanical And Tribological Properties Of Aisi D2 Steel, Indah Uswatun Hasanah, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

The effect of hard chromium coating on AISI D2's mechanical properties and wear resistance has been investigated using the electrolysis technique with varying current and coating duration. The variations of current used are 0.8 A, 1.2 A, and 1.6 A, while the coating duration used are 300, 600 and 900 seconds. Characterization of the films was conducted using SEM-EDS, and XRD. It can be observed from SEM characterization that the chrome grains resulted from the electroplating process are fine. The XRD identify chrome compund on the surface coating. The highest hardness value was 520.6 HV on a sample with a …

Microfabrication Of Silicon Carbide And Metallized Polymers Using A Femtosecond Laser, Joseph Taylor Eddy

Theses and Dissertations

Femtosecond lasers deliver a high peak concentration of optical power while maintaining low average power. With an accompanying optical setup, this power can be focused and used for high-precision fabrication of metallized polymers via ablation, creating conductive structures on a thin film. These lasers can also be harnessed in tandem with hydrofluoric acid and the two-photon absorption principle to selectively etch silicon carbide, a very durable and machining-resistant semiconductor with desirable properties. This thesis presents improvements made to the Laser-Assisted Chemical Etching (LACE) technique and the ablation system. ��, the two- photon absorption coefficient of silicon carbide, is measured and …

The Effect Of Heat Treatment And Chemical Treatment On Natural Fibre To The Durability Of Wood Plastic Composites – A Review, Nuratiqah Asyiqin Mohd Nasharudin, Nur Fatihah Sulaiman, Nurul Aziemah Mohammad, Wan Nor Raihan Wan Jaafar, Falah Abu Dr., Siti Norasmah Surip

Journal of Materials Exploration and Findings

The application of WPC is not only limited to indoor applications but has been extended to exterior applications where properties of WPC could compromise during service life. WPC was derived from wood fiber of various sizes to reinforce polymers. Wood fiber has the advantage of a cheaper price, being abundantly available, and ease of processing, however, the critical factor is its hydrophilic nature, where moisture absorption is likely to occur. Thus, treatments for reducing the hydrophilicity of wood fibers are applied. By treatment of wood fiber, the surface impurities were removed, leaving the roughened surface of fibers, thus providing a …

Probabilistic Modeling Of North Atlantic Ocean Hurricane Spawn Considering Climate Change, Susmita Bhowmik, Weichiang Pang, Michael Stoner

Publications

Hurricanes are a significant natural hazard, which cause significant damage and financial losses in the coastal areas of the United States almost every year. For example, the devastating nature of North Atlantic Ocean (NAO) storms can easily be understood from the 2005 Hurricane Katrina, which was the most damaging NAO storm in modern history, causing more than 1,800 deaths and a financial loss of at least 161.3 billion USD. It has been found that the formations of hurricanes depend heavily on climate conditions, which implies a direct relationship between the changes in climate extremes and the occurrences of hurricanes or …

Learning Dynamic Information Of High-Dimensional Signal Time-Series Using Advanced Machine Learning/Artificial Intelligence, Guannan Liu

LSU Doctoral Dissertations

In this dissertation, we propose a novel simulation-based device-free indoor localization and tracking system using the received signal strength indicators (RSSIs) of WiFi signals as the input features. The Feko channel-propagation simulation software is used to process the RSSI maps of the given arbitrary indoor geometry. In order to learn the dynamic information of high-dimensional RSSI time-series, we propose three procedures for the localization and dynamic tracking system.

First, The indoor geometry is partitioned into several equi-size zones and the localization problem is treated as the typical \multi-classification" problem. The advanced machine-learning techniques such as decision tree (DT) classifier, random …

Generation Of Vector Vortex Wave Modes In Cylindrical Waveguides, Md Khadimul Islam, Pawan Gaire, Arjuna Madanayake, Shubhendu Bhardwaj

Department of Electrical and Computer Engineering: Faculty Publications

In this paper, we propose a method to generate Vector Vortex Modes (VVM) inside a metallic cylindrical waveguide at microwave frequencies and demonstrate the experimental validation of the concept. Vector vortex modes of EM waves can carry both spin and orbital angular momentum as they propagate within a tubular medium. The existence of such waves in tubular media can be beneficial to wireless communication in such structures. These waves can carry different orbital angular momentum and spin angular momentum, and therefore, they feature the ability to carry multiple orthogonal modes at the same frequency due to spatial structure of the …

Politicians, Pundits, And Platform Migration: A Comparison Of Political Polarization On Parler And Twitter, Abigial Matthews, Jacqueline M. Otala, Esma Wali, Gillian Kurtic, Lynden Millington, Michael Simpson, Jeanna Matthews, Golshan Madraki

Northeast Journal of Complex Systems (NEJCS)

Parler, a self-proclaimed free speech social media platform founded in 2018, attracted a large influx of new members in 2020 as the result of a highly visible platform migration campaign. Parler usage was linked to the planning of the Jan. 6, 2021 attack on the United States Capitol building, leading to a shutdown of the Parler platform. Parler, which is now back online, offers an important lens through which to examine the broader attempts at platform migration in response to changing content moderation and platform governance policies and their impact on political polarization. We begin by examining the network connections …

Development Of A Covid-19 Vulnerability Index (Cvi) For The Counties And Residents Of New Jersey, Usa., Remo Disalvatore, Sarah K Bauer, Jeong Eun Ahn, Kauser Jahan

Henry M. Rowan College of Engineering Departmental Research

The coronavirus disease 2019, or COVID-19, has impacted countless aspects of everyday life since it was declared a global pandemic by the World Health Organization in March of 2020. From societal to economic impacts, COVID-19 and its variants will leave a lasting impact on our society and the world. During the height of the pandemic, it became increasingly evident that indices, such as the Center for Disease Control's (CDC) Social Vulnerability Index (SVI), were instrumental in predicting vulnerabilities within a community. The CDC's SVI provides important estimates on which communities will be more susceptible to 'hazard events' by compiling a …

List Of 121 Papers Citing One Or More Skin Lesion Image Datasets, Neda Alipour

Other resources

No abstract provided.

Characterizing Wind-Wave Flow Physics And Loading Effects On Power Transmission Systems And Offshore Wind Turbines, Tianqi Ma

LSU Doctoral Dissertations

Recent extreme hurricanes caused extensive damage to critical civil infrastructure. Accurate modeling of the extreme complex wind fields and coupled wind-wave fields is essential to quantify the single wind or combined wind-wave loading effects on the structures. This research aims to characterize wind and wind-wave flow physics to quantify the loading effect on power transmission systems and offshore wind turbines.

First, a microscale (∼km) high-fidelity high-resolution computational model is developed to simulate hurricane wind fields with detailed physics. The generated wind field is applied to analyze the structural response of a power transmission system. The proposed hurricane boundary layer (HBL) …

Crashworthy Perforated Square Steel Tube (Psst) Mailbox Support – Phase I, Robert W. Bielenberg, Cody S. Stolle, Ronald K. Faller

Nebraska Department of Transportation: Research Reports

Federal requirements have made it mandatory that safe mailbox support systems be designed to yield or breakaway whenimpacted by a vehicle. The Nebraska Department of Transportation (NDOT) has previously used a non-proprietary, U-channel post mailbox support that was evaluated at the Midwest Roadside Safety Facility (MwRSF) in the 1980's. NDOT desires that the mailbox support be updated to meet MASH 2016 TL-3 safety performance criteria and be redesigned to use perforated square steel tubing (PSST) for the mailbox support post.

The objective of this research project is to develop a non-proprietary mailbox support using PSST support posts that is MASH …

Optimizing High-Performance Computing Design: The Impacts Of Bandwidth And Topology Across Workloads For Distributed Shared Memory Systems, Jonathan A. Milton

Electrical and Computer Engineering ETDs

With the complexity of high-performance computing designs continuously increasing, the importance of evaluating with simulation also grows. One of the key design aspects is the network architecture; topology and bandwidth greatly influence the overall performance and should be optimized. This work uses simulations written to run in the Structural Simulation Toolkit software framework to evaluate a variety of architecture configurations, identify the optimal design point based on expected workload, and evaluate the changes with increased scale. The results show that advanced topologies outperform legacy architectures justifying the additional design complexity; and that after a certain point increasing the bandwidth provides …

Public Sector Bim Adoption: Development And Evaluation Of Government Policy Interventions: A Systematic Literature Review, Shiyao Kuang, Alan Hore, Ahmed Hassan, Barry Mcauley, Roger West

Conference Papers

Rapid technological advancements in the Architecture, Engineering and Construction (AEC) sector have provided a significant opportunity for improving the industry's efficiency, performance and sustainability. Building Information Modelling (BIM) is an innovative approach to information management in construction that provides a structured methodology for storing and analysing building information exchanged between project stakeholders. However, successful interventions and supports introduced by the public sector in accelerating BIM adoption can be seen through BIM mandates, promotion of information management ISO standards, guidance, funding and procurement integration. In this study, a systematic literature review is adopted to identify BIM policy interventions. The study aims …

Increasing The Impact Of Utah State University's Extension Water Check Program With 5-Second Metering, Mahmud Aveek, David E. Rosenberg, Camilo Bastidas, Jeffery S. Horsburgh, Belize A. Lane, Kelly Kopp, Peter Mayer, Joe Fazio

Reports

Study Goal – Increase the volume of water saved by the Utah State University (USU) Extension landscape Water Check program because outdoor water use is the largest component of residential use with the largest opportunity to reduce use. We used 5-second water use data collected with Flume Smart Home Water Monitoring devices (Figure 1) at residential homes before and after a Water Check (Box 1; Figure 2) to answer four questions:

1. How much water did households save?
2. Which Water Check recommendations did participants implement?
3. Why did participants implement some recommendations and not others?
4. How to further reduce landscape water use?

Residential Building Flood Risk Assessment And The Benefits Of Home Elevation, Ayat Al Assi

LSU Doctoral Dissertations

Evaluating flood risk is an essential component of understanding and increasing community resilience. A robust approach for quantifying flood risk in terms of average annual loss (AAL) in dollars is needed to provide valuable information for stakeholder decision-making inside and outside the special flood hazard area (SFHA, which corresponds to the 100-year floodplain). To further inform flood mitigation strategies, quantifying flood risk reduction with home elevation above an initial first-floor height (FFH₀) and the cost effectiveness of federal mitigation assistance for elevation are important steps to enhance awareness of the effect of elevation in reducing flood risk. …

Increasing The Impact Of Utah State University’S Extension Water Check Program With 5-Second Metering, Mahmud Aveek, David E. Rosenberg, Camilo Bastidas, Jeffery S. Horsburgh, Belize A. Lane, Kelly Kopp, Peter Mayer, Joe Fazio

Reports

Study Goal – Increase the volume of water saved by the Utah State University (USU) Extension landscape Water Check program because outdoor water use is the largest component of residential use with the largest opportunity to reduce use. We used 5-second water use data collected with Flume Smart Home Water Monitoring devices (Figure 1) at residential homes before and after a Water Check (Box 1; Figure 2) to answer four questions:

1. How much water did households save?

2. Which Water Check recommendations did participants implement?

3. Why did participants implement some recommendations and not others?

4. How to further reduce landscape water use?

Mesoporous Particle Embedded Nanofibrous Scaffolds Sustain Biological Factors For Tendon Tissue Engineering, Chiara Rinoldi, Ewa KijeńSka-GawrońSka, Marcin Heljak, Jakub Jaroszewicz, Artur KamińSki, Ali Khademhosseini, Ali Tamayol, Wojciech Swieszkowski

Department of Mechanical and Materials Engineering: Faculty Publications

In recent years, fiber-based systems have been explored in the frame of tissue engineering due to their robustness in recapitulating the architecture and mechanical properties of native tissues. Such scaffolds offer anisotropic architecture capable of reproducing the native collagen fibers’ orientation and distribution. Moreover, fibrous constructs might provide a biomimetic environment for cell encapsulation and proliferation as well as influence their orientation and distribution. In this work, we combine two fiber fabrication techniques, such as electrospinning and wet-spinning, in order to obtain novel cell-laden 3D fibrous layered scaffolds which can simultaneously provide: (i) mechanical support; (ii) suitable microenvironment for 3D …

Assessing The Impact Of Spatial Resolution Of Uas-Based Remote Sensing And Spectral Resolution Of Proximal Sensing On Crop Nitrogen Retrieval Accuracy, Kianoosh Hassani, Hamed Gholizadeh, Saleh Taghvaeian, Victoria Natalie, Jonathan Carpenter, Jamey Jacob

Department of Agricultural and Biological Systems Engineering: Faculty Publications

Foliar nitrogen (N) plays a central role in photosynthetic machinery of plants, regulating their growth rates. However, field-based methods for monitoring plant N concentration are costly and limited in their ability to cover large spatial extents. In this study, we had two objectives: (1) assess the capability of unoccupied aerial system (UAS) and non-imaging spectroscopic data in estimating sorghum and corn N concentration and (2) determine the impact of spatial and spectral resolution of reflectance data on estimating sorghum and corn N concentration. We used a UAS and an ASD spectroradiometer to collect canopy- and leaf-level spectral data from sorghum …

The Intertwined Renewable Energy–Water–Environment (Rewe) Nexus Challenges And Opportunities: A Case Study Of California, Shahryar Jafarinejad, Rebecca R. Hernandez, Sajjad Bigham, Bryan S. Beckingham

Michigan Tech Publications, Part 1

In our built environment, societal production of energy and clean water is inextricably linked to the natural resources from which they are derived. Acknowledgement and consideration of the coupling of energy, water, and the environment (the energy–water–environment nexus) will be critical to a sustainable future. This is particularly true as we transition away from historical energy sources (e.g., coal, petroleum, natural gas) and into the widespread adaptation of renewable energy (RE) sources (e.g., solar, wind, geothermal, hydro, bioenergy) as a strategy to decrease greenhouse gas emissions and consequently slow global climate change. This transition is fraught with both challenges and …

Adsorptive–Photocatalytic Performance For Antibiotic And Personal Care Product Using Cu0.5Mn0.5Fe2O4, Chanat Chokejaroenrat, Chainarong Sakulthaew, Athaphon Angkaew, Apiladda Pattanateeradetch, Wuttinun Raksajit, Kanokwan Teingtham, Piyaporn Phansak, Pawee Klongvessa, Daniel D. Snow, Clifford E. Harris, Steven Comfort

Nebraska Water Center: Faculty Publications

The amount of antibiotics and personal care products entering local sewage systems and ultimately natural waters is increasing and raising concerns about long-term human health effects. We developed an adsorptive photocatalyst, Cu_0.5Mn_0.5Fe₂O₄ nanoparticles, utilizing co-precipitation and calcination with melamine, and quantified its efficacy in removing paraben and oxytetracycline (OTC). During melamine calcination, Cu_0.5Mn_0.5Fe₂O₄ recrystallized, improving material crystallinity and purity for the adsorptive–photocatalytic reaction. Kinetic experiments showed that all four parabens and OTC were removed within 120 and 45 min. We found that contaminant adsorption and reaction …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario F. Buchely, Ronald J. O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the Face-Centered Cubic (FCC) Multi-Principal Element Alloys (MPEAs) Developed Thus Far Contain Cobalt. for Many Applications, it is Either required or Beneficial to Avoid Cobalt, Since Cobalt Has Long-Term Activation Issue (For Nuclear Applications), is Expensive, and is Considered a Critical Material. in Addition, FCC Structured Solid-Solution MPEAs Tend to Have Relatively Low Strength. a FCC Solid-Solution Fe30Ni30Mn30Cr10 (At %) MPEA Was Fabricated Via Arc Melting, Followed by Homogenization at 1100 °C for 12 H. the Alloy Was Hot Rolled at 1100 °C with a Total Reduction of Up to 97 %. the Microstructure Was Characterized and Mechanical …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

Optimizing The Membrane-Assisted Recovery Of Solids (Mars) Technology For Nutrient Removal And Recovery From Concentrated Waste Streams, Ben Yamin Hoque

USF Tampa Graduate Theses and Dissertations

The effective management of nutrients, such as nitrogen and phosphorus, in decentralizedwastewater treatment environments is a pressing challenge. These nutrients pose significant risks to the environment and public health when discharged into water bodies, while their recovery and reuse can help alleviate nutrient shortages in various industries, including agriculture. Conventional biological treatment methods used in centralized facilities are not suitable for decentralized systems due to operational complexities and space limitations. Chemical treatment mechanisms, such as adsorption, ion exchange, precipitation, and air-stripping, offer potential solutions but are accompanied by challenges like high costs and logistical issues. Therefore, finding a sustainable and …