Engineering Commons^™

Heat Capacity Ratios Calculated From The Benedict-Webb-Rubin Equation State, Edward George Delaney

Theses

The ratio of the isobaric heat capacity to the constant volume heat capacity has been calculated over a range of temperatures and pressures for the following hydrocarbons: methane, ethylene, ethane, propane, and n-butane. Graphs and tables of calculated data are presented showing the effect of temperature and pressure on the ratio of the heat capacities for these compounds.

The deviations of the heat capacities from ideal gas behavior were calculated by previous investigators from an equation based on the Benedict-Webb-Rubin equation of state, Experimental data were used to evaluate the heat capacities of the ideal gases, and were used together …

The Sulfonation Of Some Aromatic Compounds Using Sulfuric Acid In The Presence Of Thionyl Chloride, Paul Juergens

Theses

The rate of reaction in the sulfonation of some aromatic compounds with sulfuric acid was increased by the presence of thionyl chloride which, by reacting with the water of formation, effectively maintained the concentration of sulfuric acid above the level at which sulfonation can occur. The thionyl chloride had no measurable effect on the formation of isomers.

The sulfonstion reactions studied included those of toluene, naphthalene, bromobenzene, ortho-bromotoluene, and chlorobenzene.

Prediction Of Vapor-Liquid Equilibria, Daniel James Mchale

Theses

Several equations for predicting vapor-liquid equilibria from the physical properties of the components have been proposed in the literature. Two equations of this type proposed by O. Redlich and others have been investigated to determine their utility.

Results indicate the two equations give fairly satisfactory results for nearly ideal solutions, but are unsatisfactory for non-ideal solutions. Knowledge of molecular interactions in the solution would be necessary before the predictions could be used with confidence.

Variation Of Thickness Of Hard Anodic Films, Alphons Raymond O'Konski

Theses

An investigation was made of the effects of varying processing conditions on the thickness of anodic films produced by the Martin Hard Coat (4) process on commercially pure aluminum and nine aluminum alloys.

This study was conducted to provide sufficient data for designing coating thicknesses on aircraft accessory parts that would conform to the close tolerances maintained in the course of manufacture of precision components. Coating thicknesses up to 0.0051 in. were obtained. Changes in electrolyte strength, temperature of the bath, alloy composition, and current density were made to see their effect on the thickness of the film and growth …

The Determination Of Thoria In Tungsten Electrodes, Louis Arthur Prince

Theses

Two methods of analysis to determine thoria (thorium oxide, ThO₂) content of thoriated tungsten electrodes are investigated.

Chlorination methods are shown to leave thoria residues contaminated with tungstic oxide which may not be removed by extended chlorination. Ignition of the sample in air before chlorination increases contamination. A correction for the tungstic oxide in the residue is obtained colorimetrically.

The classical hydrofluoric-nitric mixed acid method is modified and shown to be equally as accurate, less exposed to operator's error, and more rapid than chlorination methods. Thin-walled polyethylene beakers are preferable to platinum ware for dissolving the sample, and …

A Proposed Method Of Analysis For Vitamin A Acetate And Vitamin A Palmitate Bulk, Julian Anthony Volpe

Theses

An ethyl acetate solution of Vitamin A Acetate and Palmitate can be determined calorimetrically with the addition of concentrated hydrochloric acid in the proper ratio; one part of ethylacetate-Vitamin A solution to four parts of acid. A purplish-blue color is produced which reaches its maximum intensity within one minute and lasts for ten minutes. This color can be read in the Ilett-Summerson colorimeter using glass filter #54. Like many colorimetric determinations, this method is valid within certain concentration limits of sample, 20-225 milligrams of Vitamin A per final 5 milliliter aliquot.

The Reduction Of The Sodium Salt Of 2-Nitro-Phenol-4-Sulfonic Acid With Sodium Sulfide And Sodium Polysulfide, Robert Leslie Waer

Theses

Analytical techniques were studied for the determination of the purity of the sodium salt of 2-nitrophenol-4-sulfonic acid. The best method proved to be reduction followed by diazotisation.

The reduction of the sodium salt of 2 2-nitrophenol-4-sulfonic acid was carried out at various times and temperatures using sodium sulfide and sodium polysulfides as reducing agents. The reduction rate was very slow using sodium sulfide and only fair using sodium polysulfide solutions. Difficulties were experienced because of air oxidation.

The amount of reaction of sodium sulfide in the presence of a large excess of the sodium salt of 2 -nitrophenol-4 -sulfonic acid …

Use Of Liquid Sulfur Trioxide As A Sulfonating Agent For Organic Compounds, Herman Gustav Weiland

Theses

Dodecylbenzene was sulfonated with SO₃ and evaluated as to ash, sodium sulfate, degree of sulfonation, and was also compared with an oleum sulfonation. Its homolog, octadecylbenzene, was made, sulfonated, and found to be less effective as a wetting agent.

Two-ethylhexyl cinnamate, oleic acid, and propyloleate were also sulfonated with good yields and evaluated.

Yields in the sulfonation of Di-2-ethylhexyl maleate were very low. There was evidence of the SO₃ splitting the ester and oxidising it to maleic acid.

The reduction of 9-octadecenophenone, according to Clemmenson's Method, led to the formation of a polymer.

The Heat Of Mixing Of Diactone Alcohol And Water At 25 C, Frederic Miller Konrad

Theses

A calorimeter of twin design with auxiliary apparatus was built for measuring the heat of mixing with a maximum error of ± 1.0%. Reliability of the apparatus was tested with the benzene-methanol system and gave results comparable to those of other investigators with apparatus of different design.

The heat of mixing of diacetone alcohol and water was measured at 25°C over the entire concentration range. A peak value of 238 cal/mole solution was obtained at 0.67 mole fraction water the mixing of two moles water with one of diacetone alcohol.

Specific heat of diacetone alcohol-water mixtures was also measured at …

Continuous Chlorosulfonation Of Benzene : I. Phase Relations, Henry Benjamin Lange

Theses

This work presents liquid-liquid equilibria data on a system suitable for continuous chlorosulfonation of benzene. Complete information is presented for the ternary, chlorosulfonic acid - sulfuric acid - carbon tetrachloride. A partial investigation of the ternary systems, chlorosulfonic acid - sulfuric acid - benzenesulfonyl chloride; chlorosulfonic acid - carbon tetrachloride - benzenesulfonyl chloride; and the quaternary system, carbon tetrachloride - benzenesulfonyl chloride sulfuric acid - chlorosulfonic acid is also presented.

Power Characteristics Of Disc Type Agitator Impellers, Isadore Rubin

Theses

Experiments were conducted to determine the power required to drive disc type agitators and to observe the flowpattern and type of agitation produced in a baffled tank.

Power was measured by determining electrical energy input to a motor and subtracting motor transmission and friction losses previously established by calibration. Impellers were operated at speeds from 600 to 3700 RPM.

Power requirements in the turbulent flow region were correlated by the equation HP = PoL⁵N³ρ/550gc which was derived theoretically.

Reports of previous work on agitator power are discussed.

The Power Numbers (Po) established for the turbulent range, …

Intermediates For P-Acetamidocinnamic Ester Synthesis, William Grayson Fix

Theses

After a review of the various methods found in the literature, a series of reactions were selected which were reported to have good yields.

Using p-nitrotoluene as a starting material, a simultaneous oxidation and reduction with sodium polysulfide was investigated as a means of making p-aminobenzaldehyde. Experimental procedures and yields were reported, and improved methods of recovery were described.

Using p-aminobenzaldehyde from the first reaction, a condensation with malonic acid, in pyridine-piperidine medium, was investigated as a means of preparing p-aminocinnamic acid.

A recommended procedure was described, and some suggestions were made concerning the completion of the synthesis of p-acetamidocinnamic …

Graphical Correlation Of Pressure Drop And Temperature Drop To Friction And Velocity For Adiabatic Flow Of Compressible Fluids, Andrew Anthony Giacobbe

Theses

Problems involving adiabatic flow of compressible fluids in horizontal conduits of constant cross-section usually require tedious trial and error solutions. Although several somewhat simplified methods have been developed, most of these methods are not ideally suited for problems involving flow between two sections of a conduit.

The graphical solutions presented in this paper, relating pressure and temperature ratios to friction and initial Mach numbers, have been developed specifically for flow between sections of a conduit. Use of the graphs requires only the knowledge of initial conditions and determination of the friction factor.

Initial velocities from 30% to 70% of the …

Vapor-Liquid Equilibrium Data And Distillation Packing Evaluation At High Vacuum, Edward Joseph Lasch

Theses

Vapor pressure date and vapor-liquid equilibria date at 1-30 m.m. pressure are presented for benzyl alcohol and benzyl-n-butyl ether system. Activity coefficients for the system are symetrical, the Margules constants ere A_1-2 = A_2-1= .301. HETP values observed at a condenser pressure of 1 m.m. for 1/4" and 3/4" Berl saddles, 1" Intalox saddles, Fibre Glass Combination packings # 076 and # 476, and a Knitted Wire Mesh pecking are presented as a function of the mass throughput and column pressure drop. At a condenser pressure of 1 m.m. the pressure drop per foot in terms of …

Prediction Of Liquid-Liquid Phase Equilibrium Data, William Frank Meola

Theses

This paper covers two methods for the prediction of liquid-liquid equilibrium data in ternary systems consisting of two hydrocarbons and a solvent and forming two liquid phases. One method is that of Pennington and Merril (ii) and the other is that described by Treybal (16), with some simplifying assumptions by the author. Both methods were applied to seven ternary systems in the present study. Five of the systems investigated were found to give rood agreement with experimental results. The assumptions made in deriving the equations for the two methods of prediction did not hold for the other two systems and …

Isobaric Heat Capacity Of Propylene Over A Wide Range Of Temperature And Pressure, Joseph Patrick Tassoney

Theses

This work was done to make possible more accurate design calculatioas for processes that require accurate data on the heat capacity of propylene at elevated temperatures and pressures.

The effect of pressure and temperature on the isobaric heat opacity and the heat capacity at constant volume for propylene relative to the ideal gas state is presented. The results cover pressures from 0 to 9,500 PSIA and temperatures from 350°F. to 2240°F.

An equation was derived from the Benedict-Webb-Rubin equation of state. This equation gives the deviation from the ideal gas state of the isobaric heat capacity of propylene for the …

A Generalized Correlation For The Effect Of Pressure On The Isobaric Heat Capacity Of Gases, Alvin Harvey Weiss

Theses

A generalized correlation is submitted for the deviation of the isobaric heat capacity of hydrocarbons from the ideal state. The range of conditions included is from reduced pressure = 0.2 - 15 and reduced temperature = 1.0 - 5.5. The curves presented have been based on data calculated from the Benedict - Webb - Rubin Equation of State, which is believed to be the most accurate method presently available for caleulating the heat capacity deviation.

The results indicate that the order of magnitude of the correction ts quite large, especially in the critical region. The average absolute error of this …

Construction Of A Mechanically Agitated Autoclave, Stephen A. O'Hare

Bachelors Theses and Reports, 1928 - 1970

Since the beginning of World War II a great deal of investigation has been done on the tungsten deposits in the western United States. These deposits are principally composed of scheelite. The scheelite deposits in the western United States are low grade, and disseminated. With the development of nonmetallic flotation methods these vast deposits of scheelite-bearing ores have become a major source of tungsten for the United States, as the high grade ore deposits have become practically depleted.

Viscosity Of Non-Newtonian Suspensions, David Edward Gullett, Edward Curtis

Theses

The object of this project ras to obtain a reasonable correlation of the effect of velocity, concentration and particle size on apparent viscosity of non-Newtonian slurries.

Through the use of dimensional and graphical analysis an equation, μ/μ_w=1.02(Ak/GC)^.105, was developed which filled these conditions. The average deviation of the apparent viscosity calculated from this equation compared to the experimental value was 14.4%.

The authors believe that this correlation should be tested under a greater variety of conditions of particle size and particle thermal conductivity and for suspending mediums other than water.

Investigation Of 3-Methyl-2-Penten-4-Yne-L-Ol (Cis Form), Lawrence John Ferrari

Theses

The isomerization of 3-methyl-l-penten-4-yne-3-ol into trans-3-methy-2-penten-4-yne-1-ol and an isomer assumed to be the cis form has been studied. The problem of determining whether or not the arbitrarily assumed isomer is a geometrical isomer or an ordinary isomer has been brought forward in industry in the course of a synthesis of Vitamin A.

Qualitative tests on the questionable isomer were without result because of the activity that the unsaturated bonds exhibited when reagents were used to test it. AU possible isomers of the compound were reviewed and the following chemical means were employed to prove that the isomer was the geometric …

Heat Transfer Characteristics Of Non-Newtonian Suspensions, Foster C. Franks, Salvador Faust Rinaldi

Theses

A dimensionless equation resembling the Dittus-Boelter equation with modified exponents and additional dimension less groups has been developed by J. J. Salamone. (12)

HD/K_f = Z(DV_Bρ_B/µ_B⁶(C_fµ_B/K_f^y(D/D_s)^r(C_s/C_f)^J(K_s/K_f)^η(1)

Salamone investigated the range of Reynolds number between 50,000 and 200,000. The results of the correlated data gave the = following exponents for equation; (1)

HD/K_f = .131(DV_Bρ_B/µ_B^.62(C_fµ_B/K_f^.35(D/D …

Application Of Theory To Extrusion Of Polyethylene, Ernest Edward Griesser

Theses

This thesis reviews the theory of isothermal melt extrusion beginning with the writings of early researchers up to its present state. The isothermal extrusion of a near-Newtonian liquid is compared to polyethylene, using five different extrusion screws, and calculated discharge rates are compared to the actual rates for both materials. A method of calculating forward flow was developed and this was shown to provide very good correlation with actual dis-charge rates.

Non-isothermal or plasticating extrusion of polyethylene was also studied and comparison is made to isothermal melt extrusion. The results obtained with the various types of screws studied are also …

Esters Of Sulfanilic And Substituted Sulfanilic Acids, Stephen James Kovalsky

Theses

Attempted esterification of p-acetaminobenezenesulfonyl chloride with any of the low molecular weight alcohols in aqueous systems always results in the formation of sulfanilic acid. When conducted in a non-aqueous medium, the desired esterification did not occur. A water soluble compound formed, instead, which has not yet been identified.

A study was made of sulfanilic acid esters. Alcoholysis reactions involving the butyl ester and methyl alcohol were successful only when the reaction was conducted under pressure and under anhydrous conditions.

A Study Of Servomechanism Damping Methods, Arthur J. Clark Jr.

Electrical and Computer Engineering ETDs

The purpose of this study is first to present a review of the general effects of damping, both Coulomb and Viscous, and feedback devices resulting in error rate damping: second to present detailed mathematical analyses of a number of special damping devices that may be used to advantage in servomechanism design.

A Shock Tube For Transonic And Supersonic Aerodynamic Research, John Hopkins Atkinson

Mechanical Engineering ETDs

The purpose of building a shock tube was to give the University another research tool and demonstration instrument for aerodynamic studies since the present wind tunnel is not suitable for high velocity research. It was hoped that the shock tube might, when calibrated against theoretical flow data, prove suitable as a test facility. Te determine its usefulness as such a facility it was necessary to devise a method for measuring local velocities, investigate size effects of models in the flow and provide a check against standard wind tunnel data. The shock tube was to be built as simply and cheaply …

A Study Of The Brittle Model Method Of Stress Analysis As Applied To Solid Circular Grooved Shafts Tested In Torsion, George V. Lemmon

Mechanical Engineering ETDs

It is the purpose of this study to (1) determine the applicability of the brittle model method of stress analysis to samples subjected to various stress raisers when tested in torsion and (2) to investigate the effects of grooved stress raisers in solid cylindrical members in tested torsion.

The Formation Of Zinc Ferrite From Zinc Sulfate And Ferric Oxide, Robert E. Morris

Bachelors Theses and Reports, 1928 - 1970

Samples of zinc sulfate and ferric oxide were roasted for periods of one, two and three hours at temperatures between 750° and 1000°C. The per cent zinc oxide combined, as zinc ferrite, was determined by dissolving the soluble zinc in a ammonium-ammonia chloride solution. Six samples were roasted at 750°C to determine the degree of decomposition of zinc sulfate to zinc oxide and sulfur trioxide.

A Study Of Certain Ferromagnetic Alloys In The System Copper-Manganese-Gallium, Harold L. Coolidge

Bachelors Theses and Reports, 1928 - 1970

Four alloys, with compositions near Cu2MnGa, were heat treated and magnetic measurements were obtained on a ferromagnetic torsion balance. The specimens were also examined microscopically to observe the structure.

Correlation Of Ordovician And Silurian Formations Of Eastern Montana, Marvin A. Lanphere

Bachelors Theses and Reports, 1928 - 1970

Correlation charts made from electric log data show the relationship of Ordovician and Silurian strata in eastern Montana. The Silurian sediments terminate westward in eastern Montana, but the Ordovician sediments are present westward into central Montana.

The Venturi-Mucker, Don A. Rohrenbach

Bachelors Theses and Reports, 1928 - 1970

Shaft sinking has been and still is one of the biggest bottlenecks in any mining operation. Consequently, the shaft is by far the most expensive and time-consuming excavation of any development program. When the shaft-sinking problem is broken up into its components, it is found that shaft mucking represents the largest fraction, both costwise and timewise. Since the mucking operation is the most important part of shaft sinking, it is, then, the most logical place for the introduction of cheaper methods.