Engineering Commons^™

Test 804: Ursus C-325 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 808: Massey-Ferguson Mf-65 Dieselmatic, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 800: John Deere 2010 Ru Gas, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 801: John Deere 1010 C Gas, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 803: John Deere 1010 Ru Diesel, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Test 802: John Deere 1010 Ru Gas.Pdf, Nebraska Tractor Test Lab

Nebraska Tractor Tests

No abstract provided.

Australian Tractor Tests : Report On Test No. 34 : Fordson Power Major, G H. Vasey, W. F. Baillie

Journal of the Department of Agriculture, Western Australia, Series 4

THIS Report is taken from the full Technical Report No. 34 of this test; test results are shown here in briefer form: fuller explanations are added.

Values quoted may be rounded out to two instead of three significant figures; to this extent the values may differ slightly but not significantly from those shown in the Technical Report

Some values are taken from graphs shown in the Technical Report, which are not shown here.

Blasting. Part 1. Explosives And The Farmer, G A. Greaves

Journal of the Department of Agriculture, Western Australia, Series 4

ABOUT 3,000 tons of commercial blasting explosives of various types are used every year in Western Australia of which approximately two thirds is utilised by mining industries and the remainder goes mainly to quarrying and public works.

The farmer and orchardist actually use only very small amounts but nevertheless explosives are a very useful working tool for the primary producer.

Australian Tractor Tests : Zetor 50 Super : Report On Test No.35, G H. Vasey

Journal of the Department of Agriculture, Western Australia, Series 4

T H I S Report is taken from the full Technical Report No. 35; results are shown here in briefer form: fuller explanations are added. Values quoted may be rounded out to two instead of three significant figures.

The Effect Of Phosphoric Acid On Compaction And Shear Characteristics Of Pure Kaolin Clay, Bhupat Hargovinddas Mehta

Masters Theses

"The work presented is the investigation of the effect of phosphoric acid on the compaction and shear characteristics of pure kaolin. Pure Georgia kaolin clay average particle size of five microns was mixed with different percentages of phosphoric acid. These mixtures were permitted to react for varying periods of time. The results of the study indicate a notable and gradual increase in dry density of the kaolin with increasing percentages of phosphoric acid admixture. The acid admixture ranges from one up to nine percent of the dry weight of the clay. Increase in cohesion of the clay with increase of …

Analyses Of Two New Electrode Configurations For Earth Resistivity Surveying, Chi-Chao Chang

Masters Theses

"Two new electrode configurations for the electrical resistivity- surveying are introduced: the A-configuration, consisting of a closely spaced pair of current electrodes separated at larger distance from the closely spaced pair of potential electrodes, and the B-configuration, in which each closely spaced pair consists both current and potential electrode. Because electrode pairs can be carried as units, the new configurations can be applied to continuous resistivity surveying more easily than the Wenner configuration....

Theoretical apparent resistivity values are derived, by Maxwell's theory of images, for the A- and B-configuration over a two layered earth using the depth probe method, and …

Crustacean Gastroliths From The Jackson Eocene Of Louisiana, Donna L. Frizzell, Wayne C. Horton

Missouri School of Mines and Metallurgy Bulletins

Wechesia louisianae, n. sp., is described from upper Eocene beds at Montgomery, Louisiana. Second species of the genus, it extends the range of Wechesia Frizzell and Exline from Claiborne (middle) Eocene and validates the generic diagnosis.

New Genera And Species Of Myripristid Fishe~ In The Gulf Coast Cenozoic, Known From Otoliths (Pisces, Beryciformes), Donna L. Frizzell, C. Kurt Lamber

Missouri School of Mines and Metallurgy Bulletins

Studies of fossil and Recent otoliths (sagittae) supply an important line of evidence, bearing on classification of teleost fishes, supplementary to that of anatomy, osteology, and "phylogenetic" paleo ichthyology.

Squirrelfishes (" Holocentridae" of authors) are generalized forms in which evolutionary divergence of some magnitude is reflected in unpreservable details of anatomy, inconspicuous skeletal structures, and striking differentiation of the sagittae. Otoliths show the holocentroid complex to consist of one homogeneous unit (l\fyripristidae, elevated) and another more heterogeneous group (Holocentridae, restricted). These lineages have been separated at least since the middle Eocene.

A revised classification, based on available lines of evidence …

Evaluation Of Protective Paint Films On Steel By X-Ray Diffraction Techniques, Donald Charles Knobeloch

Masters Theses

"Paints and related organic materials provide the most widely used means of protecting metals against corrosion. While corrosion measurements are based on a full range of quantitative methods in physical and analytical chemistry, the basic problem of evaluation work in the field of paint chemistry has been characterized by empirical testing procedures. Field tests are still of major importance and secondly, the relative value of paints may be predicted through exacting laboratory tests. However, the results of accelerated exposure tests have never successfully been correlated with service experience despite the efforts of many laboratories over a period of 35 years …

Effect Of Boundary Layer Control, Through Spiral Cuts, On The Film Coefficient Of Convective Heat Transfer, Nicholas W. Barre

Masters Theses

"This thesis is experimental investigation into the possibility of obtaining an increase in the forced convection heat transfer coefficient for a pipe by passing the fluid through a narrow spiral cut in the pipe.

Different spiral pipes with pitches of two, four, eight, ten, sixteen, and twenty inches were used; however, the width of the spiral cut remained unchanged at 3/16 of an inch. Several mass flow rates for water were used up to a maximum of 1536 lbs/hr for each run.

One of the objectives was to find which pitch would give the highest heat transfer rate for a …

A Study Of The Transient State Of Transpiration Cooling, William C. Wolkenhauer

Masters Theses

"This thesis is a successful attempt to show a new approach to the transpiration cooling problem. Transpiration cooling has long been known as an effective way of removing heat from porous material.

It is shown here that transpiration cooling from a porous material, assuming a temperature difference between the coolant and the porous material, is less effective than where the coolant within the pores is assumed to be at the same temperature as the material adjacent to the pore. Previous investigators made the latter assumption.

The specific problem considered here is that of a uniform, porous plate with constant physical …

Preliminary Study Of An Optimum Vibration Absorber For A Multi-Mass System With Multiple Excitation, John Raymond Burrows

Masters Theses

"The object of this thesis is to demonstrate, by the use of a modern digital computer, a fast, efficient method to eliminate or minimize undesirable stress conditions in a multimass vibrating system with multiple excitation. The condition desired is obtained by the addition of an optimum tuned and damped dynamic vibration absorber, for one critical speed only.

Maximum stress is the criteria used for design here and not amplitude as has been used previously by all other authors.

This solution requires the applied torque to be reevaluated as an average torque and a number of half integer harmonics. This method …

Isothermal Decomposition Of Austenite (In 1.4% Tungsten Steel) At Subcritical Temperatures, Samir Moustafa Riad

Masters Theses

"An experimental investigation was conducted in order to study the relationship between temperature, time and the decomposition of austenite in Tungsten steel of a given composition - and to plot the T-T-T Diagram for this steel.

The steel was prepared, homogenized and cut into identical specimens for further heat treatment and metallographic inspection. Precautions were taken to prevent these specimens from decarburizing during any heat treatment.

This experimental work may be divided into three main parts:-

I. Determination of the critical temperature range; i.e. the range of temperature Ae₁ and Ae₃ above which austenite is stable and below …

Transpiration Cooling Of A Plane Porous Plate, Raymond George Posgay

Masters Theses

"The transient temperatures were determined in a porous plate for one dimensional heat flow and one dimensional counter coolant flow. One surface of the porous plate was heated by a hot gas by convective heat transfer. A general discussion of the problem is considered and the procedure described for working all such problems dealing with transpiration cooling.

The solution of such problems is illustrated by two examples employing a ceramic plate one inch thick and cooled by a uniform flow of air in a direction counter to the flow of heat, while one surface of the ceramic plate was heated …

Impact Energy Coupling And Impact Seismic Refraction Using Electronic Timing, Roderick D. Carroll

Masters Theses

"The use of impact energy sources in lieu of explosives for shallow seismic investigations is limited chiefly by the low energy available. Means of increasing the energy transmission of an impact source are investigated, using a weight drop arrangement and an oscilloscope. The energy of refracted arrivals is investigated by direct overburden impacts, compaction of the overburden at the point of impact and the use of steel and aluminum plates as coupling devices. Energy transmission is shown to be greatly increased, using a suitable coupling device and the conditions for optimum coupling are discussed. The elastic constants of the ground …

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Investigation Of Vertical Internal Spillways, Paul R. Munger

Masters Theses

"This investigation resulted in the development of a means of predicting the discharge of water through an internal spillway type rockfill dam. From the data obtained during the various tests, equations were developed by which the coefficient of discharge for an internal spillway type rockfill dam can be determined when the core height, rock size and head causing flow are known. The equations give results with an error of less than 5%, which is adequate for engineering works"--Abstract, page 2.

Transient Temperature Distribution In Solid Sphere Subjected To Radiation Heat Exchange, William H. Stocklin

Masters Theses

"The author believes that numerical analysis is the most feasible approach to calculating the transient temperature distribution in a solid sphere subjected to various surface conditions; heat flow within the sphere is radial.

Numerical analysis is employed to arrive at a series of equations for calculating the transient temperature at selected points of a solid sphere. A study is made to determine a method for calculating temperatures with these equations; a computing device is found to be the most practical method for this purpose. The equations for temperatures at internal points of the solid sphere are general.

The equations have …

Electron Microscope Study Of The Systems Cadmium-Cadmium Chloride And Lead-Lead Chloride, Dennis O'Neill

Masters Theses

"The nature of the dispersed phase in the cadmium-cadmium chloride and lead-lead, chloride systems were investigated with the electron microscope.

Preliminary experiments on preparing and examining the dispersed phase showed that it was most feasible to study the material by electron-microscopic examination of replicas made from the surfaces of the fractured materials. Melting apparatus and methods were chosen so that samples of the melts could be easily quenched to different temperatures and so that the samples could be easily fractured with a minimum of surface contamination. Of the conventional replicating techniques tried, that of carbon replicas pre-shadowed with chromium was …

Effect Of Deflections For A Flat Plate By Slope-Deflection-Gyration Method, William Hsin-Loo Ying

Masters Theses

"Since the procedure for the theoretical solution of a rectangular flat plate or slab is complex, many approximate methods for determining the moments and deflections of such plate have recently been developed. One of these methods is the so called Slope-Deflection-Gyration Method which is performed by means of basically well-known structural theories - slope-deflection and torsion.

For a given plate, it is assumed that the plate is to be divided up into a grid of strips or equivalent beams at right angles to each other. The joints of this grid are assumed to be rigidly intersected and be permitted to …

Apparatus For Inductive-Electromagnetic Model Studies, Won Ho Kim

Masters Theses

"The object of this research is to design, construct and calibrate an apparatus suitable for electromagnetic model studies. A portion of the thesis is devoted to general review and theoretical consideration of electromagnetic prospecting.

Theoretical analysis of electromagnetic survey data by mathematical methods can only be carried out for simple idealized subsurface conditions. Because of the difficulties of theoretical solutions, in contrast to the simplicity of the conditions of similitude in electromagnetic exploration, a model experiment offers a very useful means of studying and comparing the response of naturally occuring conducting mineral bodies.

An apparatus suitable for inductive-electromagnetic model studies …

The Effect Of The Ultraviolet Portion Of The Sun Spectrum On Chlorine Residuals In Water Supplies, Tumkur Mohmed Ameer Ahmed

Masters Theses

"The effect of sunlight on chlorine residuals in water supplies was investigated to provide original and basic information of value to the water purification field.

Three different water systems were employed: (a) The Simplified Water System, (b) The Ground Water System, and (c) The Surface Water System. The RS Sunlamp provided an appropriate source of ultraviolet radiation. A 10 mg/1 chlorine concentration was used. The pH values of 7 and 10 and the illumination intensities of 145 and 200 foot candles were employed. Iodometric determination of chlorine residuals was the main parameter used.

It was found that the chlorine residuals …

Transpiration Cooling, Herbert S. Brahinsky

Masters Theses

"In the investigation of the problem, it is shown that the process of transpiration cooling is an effective method of cooling. This process may be applied to heat screens or heat shields, as was done in the sample problems worked out here. A porous plate with coolant flowing counter to the flow of heat was used.

The plate temperature is determined by the amount of heat flux, coolant flow, thermal conductivity of the material used as a plate, the specific heat of the fluid, the specific heat of the plate material, the density of the plate material and its porosity. …

Some Aspects Of Miscible Phase Displacement As Applied To The Recovery Of Oil Reservoir Crude, David D. Friend

Masters Theses

"Recent application of the miscible sing displacement process as a method to increase recovery from petroleum reservoirs has resulted in a great deal of laboratory investigation, none of which provided conclusive evidence as to the amount of mixing taking place between the displacing and displaced fluids. This investigation attempts to provide a possible insight into the rate and degree of mixing of two fluids with respect to flow path transversed and the rate of advance of the fluids. The laboratory investigation consisted of displacing a fluid from a packed core with another fluid under completely miscible conditions.

Experimental evidence indicates …

Deformations And Bending Moments For A Building Slab With A Central Opening, Wu Ping-Yung

Masters Theses

"The adaptability of the classical slope-deflection method analysis to the analysis of uniformly loaded building slab is the subject of this study. The paper demonstrates the use of slope-deflection in computing deflections and bending moments in uniformly loaded square building slabs both with and without central square openings. The results obtained are compared with results of other methods found by other investigators.

Numerous methods have been proposed for use in solving plate or slab problems. The exact solution in the form of a fourth order partial differential equation has proved to be of value in relatively few cases where boundary …