Engineering Commons^™

Test 887: Allis-Chalmers 190 Xt (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 889: Ford 3000 4-Speed (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 893: Ford 4000 8-Speed (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 900: Massey-Ferguson Mf 180 (Diesel), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 929: Allis-Chalmers 190 Xt (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT

GENERAL CONDITIONS

East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers.

PREPARATION FOR PERFORMANCE RUNS

The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

Test 894: Ford 2000 8-Speed (Gasoline), Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF TEST REPORT GENERAL CONDITIONS East tractor is a production model equipped for common usage. Power consuming accessories can be disconnected only when it is convenient for the operator to do so in practice. Additional weight can be added as ballast if the manufacturer regularly supplies it for sale. The static tire loads and the inflation pressures muse conform to recommendations in the Tire Standards published by the Society of Automotive Engineers. PREPARATION FOR PERFORMANCE RUNS The engine crank case is drained and refilled with a measured amount of new oil conforming to specifications in the operator’s manual. The …

The Effect Of Varying Sea Coal Fineness On Sea Coal Activity In Molding Sands, Laurence A. Cooley

Masters Theses

"An experiment was conducted in an attempt to establish a relation between sea coal activity in a facing sand and the particle size of the sea coal added to the sand. It was felt that if a sufficient difference in distribution of volatiles was detected, a correlation between particle size and activity of the sea coal within the test specimens might be established. The lack of positive evidence to support such a relationship is indicative that a variation in particle size does not promote volatile re-deposition within the range of particle sizes investigated for the particular weight per cent of …

A Study Of The Structural Rearrangements Accompanying Room Temperature Recovery Of High Purity Aluminum, Carlos Manuel Lago

Masters Theses

"X-ray methods (Laue back reflection and transmission) and etch pit studies were used in order to follow structural changes in the deformed metallic lattice during room temperature recovery. The accumulative evidence indicates that the deformed lattice undergoes subboundary movements and regrouping of fragments within a few days after stressing. On the basis of a superficial investigation, it was found that fast neutron bombardment increases the rate of room temperature recovery. Through the use of a new etchant, a finer substructure was revealed within the Lacombe subgrain. Glide strain values were determined for the series investigated, and a new approach was …

Anodic Dissolution And Disintegration Of Tin And Valency Of The Tin Ions Going Into Solution, Mrityunjoy Dutta

Masters Theses

"The increased demand for protective coatings on metals and for non-corrosive alloys has stimulated extensive research on the fundamental behavior of metals in corrosive media. One of the problems still unsolved is the nature of the mechanism of the anodic dissolution of metals like beryllium, zinc, magnesium, cadmium, tin, aluminum, iron in aqueous salt solutions. It has been reported in the literature that these metals show discrepancies which often arise between coulometric data and the weight loss of metal electrodes in various media. Several investigators have proposed different and opposing theories to explain the above deviation. The purpose of the …

The Eccentric Orifice As A Flow Measuring Device In Small Diameter Pipes, James E. Casale

Masters Theses

"This thesis reports and evaluates the use of an eccentrically placed orifice as a flow measuring device in small pipe sizes. The orifice is placed in a concentric location and moved to increasingly eccentric locations until full eccentricity is reached. At full eccentricity the circumference of the orifice is tangent to the circumference of the pipe. The effects of increasing eccentricity are evaluated for four orifices...Flow coefficients for the orifices in different locations are plotted against Reynolds numbers. The eccentric orifice is a reliable, accurate flow measuring device for metering or controlling the flow of fluids. Design criteria can be …

A Study Of Sulfide Inclusions In Medium Carbon Steels, Shane Shiang Yen

Masters Theses

"Sulfur is a very important component in steel. Usually is it present as an impurity in commercial steels. In these materials the sulfur content is 0.05 percent maximum but may be higher or lower than this in some steels...It is generally believed that sulfur has a deleterious effect on the mechanical properties of steels. Originally this investigation was to deal with this aspect of sulfur in steels but the work did not progress to this stage. An effort was made to vary the nature of the sulfides in several experimental heats of steel by controlling their composition. Variation in the …

Maximum Present Value Calculations With Digital Computers, James Boyd Robison

Masters Theses

"This paper discusses maximum present value calculations for a mineral property using digital computers. A semi-quantitative mathematical model to optimize operating conditions is considered. The model is based on a modified cash flow analysis. Many variables affect the solution, and their effect upon present value is described. Selected data (mining rate, costs, reserves, metal sales price, and others) for a hypothetical open pit copper mine are used in a set of solutions for present value. The results are discussed in detail. It is concluded that: (1) Digital computer methods are rapid and useful, (2) Changes in the mining rate, average …

Active Band-Pass Filters Using Twin-Tee Networks, Terry B. Watson

Masters Theses

"The primary objective of this thesis was the design and construction of a set of filters to determine the spectral energy density of random signal data in the spectrum from 10 cps to 20 kcps. The statement of the problem placed rather exacting conditions on the cost and performance of the equipment, and these conditions were met to the extent detailed in the following pages. A secondary objective was the investigation of techniques to improve the performance of band-pass active filters using resistive-capacitive feedback networks. This objective was not achieved to the author's satisfaction, although several promising ideas were discovered"--Abstract, …

A Study Of The Effect Of Surface Beveling On Silicon Rectifiers, Gary L. Voorhis

Masters Theses

"The problem in this thesis is to experimentally obtain voltage vs distance data for different angles of bevel, to determine the optimum bevel angle on the basis of minimum surface electric field, and also to determine the location of the maximum surface electric field with respect to the p-n junction. Experimental equipment is constructed and results are graphically illustrated. It is concluded that in general the maximum surface electric field decreased as the bevel angle decreased, that neglecting practical considerations the optimum bevel angle was 3⁰, and that the maximum surface electric field occurred near, but not at the p-n …

Thermal Degradation Of Poly (Methyl Methacrylate) In Solution In Various Solvents, Ya-Chih Chen

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of different molecular weights in toluene, ethyl acetate and chloroform. Four poly (methyl methacrylate) samples having molecular weights of 2,210,000, 733,000, 320,000, and 43,00, respectively were studied in this investigation. The results indicated that the polymer having a molecular weight of 2,210,000 undergoes degradation while the low molecular weight polymers having molecular weights of 733,000, 320,000, 43,000 undergo reverse polymerization"--Abstract, page [ii].

Finite Difference Solution For Triangular Plates, Hao-Yang Huang

Masters Theses

"In this thesis the finite difference method is used to solve triangular plates with uniformly distributed transverse load. As a matter of convenience triangular coordinates are used. The supporting conditions as well as the shape of plate are varied. All calculations are performed by digital computer. The patterns of differential operators in triangular coordinates, the deflections of plates, and the moment distributions are shown and discussed. The results obtained for some special cases are compared with published solutions"--Abstract, page i.

The Effect Of Epoxy Resins On The Plasticity Index Of An A-6 Soil, A. R. Van Steenbergen

Masters Theses

"This thesis reports the results of an investigation of the variation in plasticity of a clayey soil after treatment with small quantities of epoxy resin and curing agent or with curing agent alone. The series of samples tested consisted of an A-6 soil obtained from the vicinity of Rolla, Missouri, combined with: 1. 0-3% of triethylenetetramine hereafter referred to as TETA. 2. 0-3% of diethylenetriamine hereafter referred to as DETA. 3. 0-3% of Araldite 6010 resin cured with TETA. The TETA content was varied form 20% to 100% of the resin by weight. 4. 0-3% Araldite 6010 resin cured with …

Analysis Of Continuous Folded Plate Roofs, Yung-Ping Wang

Masters Theses

"This work presents an analysis of continuous folded plate roofs considering the effects of relative joint displacements. For this analysis the normal modes of the lateral beam vibration were used as the form of the deflection curve and the loading was sinusoidal. By using symmetry and anti-symmetry, a possible method of analyzing prismatic folded plate roofs comprising one bay transversely but continuous over two or more spans longitudinally is suggested"--Abstract, page ii.

Measurement Of Stray Load Loss Of D.C. Machines, Kanaiyalal Ramanlal Shah

Masters Theses

"For many years the standard practice, in calculation of conventional efficiency of d.c. machines, has been to include stray load losses as equal to 1% of the output. This assumption may be true for large, compensated d.c. machines but it is known to be small for smaller, uncompensated, general-purpose, industrial-type machines of open design. An A.I.E.E. Committee on Rotating Machines was formed to investigate whether the present practice of assigning 1% for the stray load loss is justified or not. They reached a conclusion, reported in 1949, after investigating 243 stray loss tests on different motors ranging from 1/2 hp …

Analysis Of The Flow Characteristics Through A Water Pressure Regulator, Anthony Lee Jatcko

Masters Theses

"This thesis presents an analysis of the flow characteristics through a water pressure regulator. Characteristic curves of the relationship between pressure drop through the regulator and flow through the regulator are developed. To further analyze these relationships, a least squares computer analysis was used to develop equations to fit these curves. An investigation into the modes of dissipating pressure energy in this type of regulator tends to indicate that a significant portion of the energy is lost through viscous shearing action in the area of high turbulence. The aforementioned characteristic curves also showed definite critical pressure points in the form …

Application Of The Photoelastic Coating Method To Evaluate The Stress Distribution On The External Surface Of The Cap Of An Electrical Insulator, Harijeetsinh Jagtiani

Masters Theses

"The Photoelastic Coating Method was applied to find the surface stresses on the cap of an electrical insulator. The strain distribution was observed and photographed. This color photograph indicated a visible geography of the maximum shear strain distribution in the region of the insulator where the birefringent plastic was bonded with a reflective cement. The Oblique Incidence technique was used to determine the principal stresses from the maximum shear strain (or the principal strain difference) readings, obtained from Normal Incidence. The critical cross-section of the insulator head was optically located, giving an initiative for the re-design of the insulator cap. …

Thermal Degradation Of Poly (Methyl Methacrylate) In Solutions In A Closed System, Vikram Pranjivandas Parikh

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of two different molecular weights, 2,303,000 and 43,000, in 1,2-dichloroethane in a closed system. The results indicated that the polymer having a molecular weight of 2,303,000 undergoes degradation while the low molecular weight polymer 43,000 undergoes reverse polymerization, and the molecular weight remains constant. The molecular weight of high molecular weight samples after 48 hours decreased from 2,303,000 to 2,232,000 and 1,690,400 at 50⁰C and at 98.5⁰C, respectively"--Abstract, page [i].

The Electrochemical Oxidation Of Crotonic Acid, John L. Cannaday

Masters Theses

"The purpose of this investigation was to explain the mechanism of the electrochemical oxidation of crotonic acid on platinized-platinum anodes at 80⁰C.

A current-potential study was conducted using the parameters of pH and crotonic acid concentration. Faradaic efficiency was determined by measurement of CO₂ production.

Oxidation occurred both in acidic and basic solutions.The Faradaic efficiency was approximately 100 per cent.

The results were interpreted in terms of a mechanism having the following characteristics.

(a) The first charge transfer is the rate determining step.

(b) The rate is the sum of the rates for two parallel reactions. In strongly acidic solutions, …

Mass Transfer In The Electrodialytic Desalination Of Brackish Water And A Correlation Of Experimental Data With Theory, James Shih-Jiann Yang

Masters Theses

"The object of this work is an experimental investigation into the possibility of obtaining an increase in mass transfer in the electrodialysis of brackish water by altering the physical character of the selective membrane, and a correlation of experimental mass transfer data with theory"--Introduction, page 1.

Comparison Of Measured And Calculated Stiffnesses For Lightweight Normal Concrete Beams, Raman Patel

Masters Theses

"This study is a presentation of the findings involving experimental measurements of stiffness (EI) for different percentages of reinforcement steel in normal and lightweight concrete beams. The experimental values of stiffness are compared with calculated values obtained by applying the standard reinforced concrete theory. The measured values of stiffness obtained by the rotation method are compared with those obtained by the deflection method. Of the thirty beams that were tested, fifteen were tested for normal concrete and the remaining fifteen for lightweight concrete. Each of these beams were tested at different ages, ranging from seven to twenty-eight days.

The test …

Warping And Curling Of Plain Concrete Slabs, Vipinbhai Ratilal Shah

Masters Theses

"The study was made to determine the effect of daily atmospheric temperature variation and curing on the warping and curling of plain concrete slabs and to study the effect of moisture on the warping of plain concrete slabs under nearly constant temperature conditions, by keeping the bottom surface of one slab wet and the other dry.

Daily observations consisted of dial gage readings to determine the progressive variations in warping contours due to typical daily temperature curling. Trends were found for three months of dial gage readings and interpreted in terms of warping and curling of the slabs.

The warping …

The Elastic And Anelastic Constants Of A Synthetic Fluor-Mica Formed By Glass-Ceramic Fabrication Techniques, John H. Ainsworth

Masters Theses

"A tetrasilicic fluor mica, K₂Mg₅Si₈O₂₀F₄, was synthesized using glass forming techniques. Density changes, weight losses, and shrinkage, as well as elastic and anelastic properties, were measured on bars heat-treated at selected temperatures between 500°C and 1150°C to determine the characteristics of this material. Phase changes were followed by determining thermal expansion, logarithmic decrement, and modulus of elasticity from room temperature to 800°C.

It was found that the elastic and anelastic constants decreased gradually with heat treatments from 600°C to 1000°C. This indicated progressively increased structural ordering. Heat treatments above 1000°C …

A Study Of The Non-Newtonian Turbulent Fluid Flow Through An Annulus, Yogesh R. Parikh

Masters Theses

"This investigation is concerned with the study of non-Newtonian flow through an annulus. The experimental analysis of incompressible non-Newtonian fluids in a long cylindrical annulus of radius ratio 0.375 was studied in the turbulent region. Different types of non-Newtonian fluids were used to procure flow behaviour for the annulus.
The effect of increasing flow rate of the non-Newtonian fluids was evaluated by gathering pressure drop data across the annulus using a differential manometer. The power-law model is used in this study to characterize the non-Newtonian flow. The parameters of the power-law model were evaluated by gathering viscometric data on a …

The Design And Construction Of A Medium Power, Synchronous, Electronic Switch, Floyd S. Hall

Masters Theses

"This paper presents the design and construction of a medium power, synchronous, electronic switch and associated timing and control circuits.

The unit described is capable of controlling a 20 ampere resistive or inductive load from a 110/220 volt, 60 Hz excitation source. Thyristors are used as the active switching elements. The period of the on/off switching cycle may be varied from 1/60 second to 8 1/2 seconds. Turn-on and turn-off may occur at independently selected phase angles relative to the reference frequency source.

Higher power operation could be obtained easily with minor design changes"--Abstract, page ii.

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …