Engineering Commons^™

Reliability Of Can-Type Precipitation Gage Measurements, C Earl Israelsen

Reports

A comprehensive review of literature was made of studies conducted since 1952 pertaining to the accuracy of can-type precipitation gage measurements. Brief discussions are given of the results of some of them, and conclusions are drawn. Topics discussed include raingage comparisons, accuracy of precipitation measurements, precipitation gage errors, and precipitation measurements in mountains. A bibliography is included

Consecutive Streamflow Averages For 90 Utah Stations, A. Leon Huber

Reports

No abstract provided.

Mathematical Simulation Of Small Watershed Hydrologic Phenomena, V. V. Dhruva Narayana, Jay M. Bagley

Reports

In many hydrologic investigations concerning small watersheds, data and observations are totally inadequate to provide a basis for outflow hydrographs. Consequently, a variety of empirical approaches have been developed which have limited rational validity. Hydrograph synthesis offers a reasonable approach to predicting the outflow hydrograph characteristics. In order to synthesize a hydrograph, it is necessary to mathematically describe the physical behavior of the dynamic processes involved in the hydrologic phenomena. Hydrograph synthesis may be considered to comprise (a) hydrographs (actual or simulated) of precipitation, (b) hydrographs of abstractions such as interception, infiltration, and depressional storage, (c) routing or translating the …

Using Remote Infrared Sensors To Detect Changes In Moisture Conditions On Natural Watersheds, Ralph D. Briscoe, Frank W. Haws

Reports

Foreword: This report summarizes the results of laboratory measurements of the infrared reflectance of selected living plants typical of the natural watersheds in northern Utah. Data indicate that the IR reflectance decreases as the moisture content of the soil decreases and the moisture tension in the soil increases. Additional data will be collected in the field to confirm the results and to further tests the feasibility of using IR reflectance of vegetation as an indicator of soil moisture conditions on the watershed. Mr. Briscoe, Research Physicist, has been responsible for the gathering of laboratory data and has written the manuscript …

Highway Construction In Windblown Silts Of Western Kentucky, Robert C. Deen

Kentucky Transportation Center Research Report

It has been shown that engineering experience and performance histories of earthwork structures and foundations in distinctive physiographic regions provide valuable insights applicable to the planning and construction of future projects. Geologic information further categorizes earth materials on the basis of parent material and geologic processes which modify the rock and soil masses. A knowledge of the resulting topographic expression or landforms and reference to geologic and soils information contained in surveys, reports, and maps is particularly useful in the early stages of planning and site selection. When sufficient information is available, regional units may be recognized for the purpose …

Skid Testing With An Automobile, Rolands L. Rizenbergs, Hugh A. Ward

Kentucky Transportation Center Research Report

A study was conducted to evaluate the theoretical and practical aspects of using an automobile as a testing device for measurement of pavement slipperiness. Every parameter and significant event in the excursion history of a skidding automobile was measured and recorded. The resultant skid-resistance values, twenty-five in all, were compared and correlated. As a result of the study, the measurement of time in the velocity increment between 30 mph to 20 mph was selected as an interim standard test. A number of experiments were also conducted to aid in the interpretation of test results and to establish control tolerances for …

The Role Of The Doctor Of Engineering Degree In Graduate Education, Wouter Bosch, Robert E. Carlile

Chemistry Faculty Research & Creative Works

No abstract provided.

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, J. R. Chott, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector Currents the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: A quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

Correction To “Analysis Of The N-Wire Exponential Line”, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

An Analytic Model For The Fluxgate Magnetometer, Stanley V. Marshall

Electrical and Computer Engineering Faculty Research & Creative Works

The output voltages from various fluxgate probe types are found to have the same general form, and an analytic model has been developed with which the output may be calculated. In the saturation region where the output pulse is developed, the differential permeability can be closely approximated by an exponential, dB/dH = k₁H^_k2, where k^_l and k^₂ are on the order of 100 and -2.0, respectively, for cores of Supermalloy or Permalloy 80. Using this model, the effect of the nature of the excitation function on output pulse amplitude and width and the effect …

The Design And Construction Of An Apparatus For The Plane Wave Analysis Of Mufflers, Stephen Philip Buckley

Masters Theses

"In the following report, a method for evaluating the attenuation characteristics of a general muffler as well as the design, construction and use of the associated apparatus are described. The method combines accepted plane wave theory and experimental techniques into a relatively straightforward approach to the analysis of acoustic filters. Equations are developed to cover the frequency range between 300 and 4000 cycles per second. Deviations from these equations extend the use of the equipment to low frequencies without the need for unduly long and cumbersome apparatus. This method, which may be called the standing wave method, utilizes a standing …

A Study Of Film Boiling Of Liquid Nitrogen And Liquid Argon Over A Wide Pressure Range With Cylindrical Heaters, V. J. Flanigan

Masters Theses

""A film boiling heat transfer study was conducted with three different diameter cylindrical copper heaters over a wide range of pressures for nitrogen and argon with the heat transfer surface in the horizontal position. The data were compared to the commonly used film boiling heat transfer relations. The common relations were found to be considerably in error for the range of variables covered in this investigation. A semi-empirical equation for corresponding states fluids which correlates the available data as a function of the reduced temperature and reduced pressure was derived and discussed"--Abstract, page iii.

Determining The Transfer Matrices Of Tapered Multiwire Transmission Lines, Clyde A. Vandivort

Masters Theses

"The advent of monolithic and integrated microelectronic circuits has aroused interest in passive multilayered thin film networks. The basic thin film network is shown in Figure 1. This structure consists of alternate resistive and dielectric layers sandwiched together. Such devices are referred to as distributed parameter RC networks. The reduction of volume and increased reliability offered by thin film devices has caused considerable effort to be extended in the analysis of their characteristics....

The incremental equivalent circuit given in Figure 2 stems directly from the above physical parameters and is the circuit used as a basis for the analysis that …

Controlled Environment Broiler Houses In Western Australia, D F. Hessels

Journal of the Department of Agriculture, Western Australia, Series 4

The three main features which contribute to the better returns from controlled environment broiler housing are higher density, better conversion and a reduction in labour.

The higher initial cost of housing and higher running costs are more than covered by these three advantages.

A Comparison Of Strength Properties Of Heat Treated Aisi 1065 Steels At High Strength Levels, Robert Lowell Hollenbeck

Masters Theses

"Six AISI C 1065 steels were heat treated and tensile tested in order to evaluate their ductility at high strength levels. Heat treating and tensile testing procedures were developed for use working with these steels at tensile strengths of 300,000 psi and higher. The austenitizing procedure in the hardening operation was found to affect the strength and ductility of the high strength samples. Rapidly heating to the austenitizing temperature followed by an immediate quench produced better properties than slow heating followed by a soaking period before the quench. However, it was concluded that the carbon contents of the steels studied …

A New Performance Index For Sensitivity And Energy Optimization., Mohamed Zafer Dajani

Masters Theses

"The principal aim of this thesis is to present a new index of performance which when minimized will simultaneously optimize the system energy and sensitivity function of a multivariable linear control system. With this performance index it is usually desirable to discriminate between the sensitivity factor and the energy term by weighting them differently. Two types of weighting factors are presented. Since it is not easy to minimize that performance index for all types of problems, further research is suggested to find methods of solution for such problems. Illustrative examples demonstrate the optimization process and the type of assumptions needed …

A Study Of The Compressibility Of Silty Soils., Marvin L. Byington

Masters Theses

"This study has been conducted to determine the applicability of the Terzaghi Theory of Consolidation and to determine the compressibility of silt soils with varying clay content. A pure silt was extracted from the Lebanon Silt Loam and mixed with varying amounts of the Onyx Cave Illite-Chlorite Clay. The compressibility of these mixtures was determined and an attempt made to apply the Terzaghi Theory in the analysis. It was found that the compressibility of soils high in silt content is very low. It was also found that the Terzaghi Theory may be applied to mixtures of 15 percent or more …

Construction Of A Laboratory Type, Convertible Excitation Argon Laser, Arthur P. Reckinger

Masters Theses

"The purpose of this thesis is to describe the construction of a general purpose, convertable [sic] excitation, laboratory type, argon laser. Quartz tubing was used in the final model while attempts to use alumina were made during earlier work. The final model has total optical power output of 230 mw at a discharge current of 29 amperes in the dc excitation mode. Provision was also made to utilize RF or pulsed excitation. The device is built so that several values of optical transmittance are available with a wide range of mirror placement"--Abstract, page ii.

Effects Of Mixing Procedure Upon Uniformity Of Fibre Reinforced Concrete, Donald E. Nortrup

Masters Theses

"This thesis describes the effects of several methods of introducing wire fibres into a concrete mix upon the uniformity of wire fibre reinforced concrete. Various mechanical and manual methods of introducing the fibres were used and comparisons of the methods were based upon variability in splitting tensile strength and the quantitative distribution of the fibres as determined by visual inspection of sawed cylinders. Test results show that the tensile strength of concrete is increased appreciably by the inclusion of steel wire fibres in the mix and the uniformity of strength is similar to that of unreinforced concrete. The methods of …

Continuous Countercurrent Evaporation Through Porous Water-Repellent Membrane With Pressure Above Atmospheric, Yung C. Hsu

Masters Theses

"An experimental method for measuring mass transfer rates at pressures above atmospheric has been developed for the case of continuous countercurrent evaporation through porous water-repellent membranes. The final developed equipment is suitable for operation under pressures up to 50 psig and at temperatures near the boiling point of 7% salt water when high flow rates are reached. Rates of evaporation of water through the membrane were measured, and the data and results were used to examine the effects of operating conditions on the over-all mass transfer resistance. Least squares equations for fitting the data were also obtained. Over-all mass transfer …

A Programmed Synthesis Procedure For Asynchronous Sequential Circuits, Robert Judson Smith

Masters Theses

"The synthesis procedure for large asynchronous normal fundamental-mode sequential circuits is time-consuming and tedious when performed manually. This paper describes a series of computer programs which, given a machine specification in flow table form, automatically produces simplified normal form implementation design equations. The user may specify that either minimum-variable state assignments, or more rapidly generated near-minimum-variable codes be found. Next-state equations are formed using the generated state assignments and converted to simplified sums of products. Sample machines having flow tables of up to eighteen rows by four columns are synthesized"--Abstract, page ii.

A Transmission Electron Microscopy Study Of Some High Strength Plain Carbon Steels, George Joseph Vytanovych

Masters Theses

"Methods of preparing foils of high strength, heat treated, plain carbon steels for examination in the electron microscope by the transmission technique were perfected and are described. Two processes for the initial thinning of a bulk sample were successful. A chemical process was found to be more rapid but not satisfactory for small samples. A mechanical process was slower, but was applicable to the smaller specimens. Electro-polishing the thinned material yielded acceptable foils from which photomicrographs of good quality were obtained. The microstructure of the high strength steel samples showed typical tempered martensite. No reasons for the differences in ductility …

Minimization And Generation Of Next-State Expressions For Asynchronous Sequential Circuits, Gary Keith Maki

Masters Theses

"One step in the synthesis procedure for realizing an asynchronous sequential circuit that is operating in fundamental mode is to obtain an internal-state assignment that will realize the operations of the circuit. Often the procedures that are used in accomplishing the above task generate several satisfactory assignments. The first part of this paper presents a method that will enable one to predict which of the internal-state assignments will yield a simpler set of next-state expressions. A second topic treated in this paper is one of presenting a method to generate the next-state expressions for an asynchronous sequential circuit directly from …

The Effect Of Concentration On The Viscosity Of Dilute And Moderately Concentrated Polymer Solutions, Hwa Luh

Masters Theses

"The effect of concentration on the viscosity of dilute and moderately concentrated polymer solutions was studied for eight narrow molecular weight polystyrene samples (900

Scanning Properties Of Unsymmetrically Loaded Aperture Arrays, Gary Dean Brunner

Masters Theses

"Radiation patterns resulting from an array of waveguide-fed apertures, filled with assymmetrically [sic] cut dielectric inserts, in an infinite ground plane were investigated. The results of Blumberg and Hemmen concerning single apertures were applied to a two-aperture array, with emphasis upon obtaining an array capable of scanning in the far field through changes in the permittivity of the assymmetrically [sic] cut dielectric inserts. Scanning was shown to be possible with up to a 60⁰ scan angle with a "push-pull" method of varying permittivities, in which the permittivity of one insert is raised while the other is lowered. The aperture field …

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, Joseph Robert Chott

Masters Theses

"When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector currents, the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: a quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

The Measurement Of Explosively Induced Stresses In Rock-Like Materials With A Capacitive Transducer, Vincent Paul Crane

Masters Theses

"A capacitive transducer was developed for measuring the free surface motion in Hydrostone blocks loaded by an explosive plane wave generator approximately one foot from the specimen. The charge to specimen distance was adjusted to produce a single spall, the position of the fracture being noted on the recovered specimen. The longitudinal wave velocity in each specimen was determined by the ultrasonic pulse technique before each shot. From the above measurements the stress, strain and strain rate at the point of fracture were determined. An attempt was made to determine the actual fracture time with imbedded [sic] conductive graphite rods, …

Lattice Constants, Thermal Expansion Coefficients, Densities, And Imperfections In Gold And The Alpha-Phase Of The Gold-Indium System, Vinayak Keshavlal Patel

Masters Theses

"An investigation of structure insensitive properties (lattice parameters, thermal expansion coefficients, densities, and imperfection) of gold and the alpha-phase of the gold-indium system was made. The gold-indium alloys were prepared from high purity (99.999%) gold and indium by melting both metals inside sealed quartz glass tubes which were first evacuated and then filled with helium gas. The solidified alloys were annealed and then examined by x-ray for homogeneity. The lattice constant of 99.999% pure gold at 25⁰C was found to be 4.07894 ł 0.00005 (corrected for refraction) Å. The coefficient of thermal expansion was 13.4 x 10⁻⁶⁰C⁻¹ between 15 and …

An Investigation Of The Effects Of An Impact On Some Of The Mechanical Properties Of Aluminum Alloy 2014-T6, Rajnikant K. Shah

Masters Theses

"Static and impact tests were conducted on an Aluminum alloy 2014-T6 specimen. The purpose of this research was to determine the effects of an impact load on some of the mechanical properties of aluminum. The cross section of the specimen measured 4.438 in. by 3.850 in. and it was 12 in. long. It was equipped with a total of four electric resistance gages connected in two pairs. One pair measured longitudinal strain while the other measured transverse strain. Both gages in each pair were mounted on the opposite sides to cancel the bending effect. In the static tests, load was …

Quality Of Surface And Subsurface Water In A Missouri Carbonate Karst Terrain (Dry Fork, Norman, And Benton Creek Watersheds), James Chi Huang

Masters Theses

"Little is known about the effect of carbonate karst terrain on water quality in the United States. Karst topography occurs over a large portion of Missouri and over a significant part of other midwestern states. The objectives of this study were the determination of the quality of surface and subsurface water in carbonate karst terrain and the investigation and evaluation of the effect of rainfall and runoff on water quality in the Meramec Spring area, east of Rolla, Missouri, during both the dry and wet seasons over the period of one year. Water samples were collected at a large number …