Engineering Commons^™

Phase 1 Inspection Report: National Dam Safety Program. Mississippi - Kaskaskia - St. Louis Basin. Little Indian Creek Dam, Washington County, Missouri, Woodward-Clyde Consultants, Chicago, Illinois

Missouri Dam Safety Inspection Reports

This report presents the results of field inspection and evaluation of the Little Indian Creek Dam (MO 30718).

It was prepared under the National Program of Inspection of Non-Federal Dams.

This dam has been classified as unsafe, non-emergency by the St. Louis District as a result of the application of the following criteria:

a. This dam retains less than 50 percent of the Probable Maximum Flood without overtopping the embankment.

b. Overtopping of the embankment could result in failure of the dam.

c. Dam failure significantly increases the hazard to loss of life downstream.

Phase 1 Inspection Report: National Dam Safety Program. Mississippi -St. Francis Basin. Nims Lake Dam, Washington County, Missouri, Woodward-Clyde Consultants, Chicago, Illinois

Missouri Dam Safety Inspection Reports

This report presents the results of field inspection and evaluation of Nims Lake Dam, Missouri Inventory Number 30064.

It was prepared under the National Program of Inspection of Non-Federal Dams.

This dam has been classified as unsafe, non-emergency by the St. Louis District as a result of the application of the following criteria:

a. Spillway will not pass 50 percent of the Probable Maximum Flood without overtopping the dam.

b. Overtopping of the dam could result in failure of the dam.

c. Dam failure significantly increases the hazard to loss of life downstream.

Calcium Migration In Dense Alumina Aged In Water And Physiological Media, Heidi H. Osterholm

Masters Theses

"The flexural strength and relative Ca concentration at the external surface were measured for a dense alumina aged in deionized water and Ringer's solution at 40⁰C for 60 weeks and at 80⁰C for 45 weeks. Changes in the Ca concentration at the external surface and flexural strength during aging were attributed to the dissolution of the calcium impurity believed to be present in a glass phase of unknown composition. Auger electron spectroscopy was used to investigate the relative concentration of the calcium impurity at the external and fracture surfaces of a dense alumina after in vivo exposure for 6, 12 …

Aerodynamic Study Of Dual Lifting Surfaces, Kamran Rokhsaz

Masters Theses

"Aerodynamic characteristics of two-dimensional dual airfoil systems have been investigated in an incompressible flow field in the area where improved aerodynamic characteristics are realized, due to the flow field coupling of the two airfoils. A simple analytic model has been developed to demonstrate some of the basic coupling effects in such systems. Laplace's differential equation for the stream-function has been solved numerically to determine the potential flow about dual airfoil geometries of different gap, stagger, and decalage. Two numerical methods have been employed; a finite-difference approach in Cartesian coordinates, for which the mixed boundary conditions have been transformed to the …

Microwave Sintering Of Batio₃ Ceramics, Kurt Duane Humphrey

Masters Theses

"Barium titanate and BaTiO₃-based multilayer capacitors were sintered in a commercial microwave oven. The oven was equipped with a 2.45 GHz continuous-wave magnetron with a maximum power output of 650 watts.

Microwave-absorbing setters made of SiC were used to offset thermal losses from the samples and allow sintering temperatures (>1325°C) to be achieved. Pure samples were pressed from commercial BaTiO₃ powder and microwave sintered to about 90% of theoretical density. Multilayer capacitors were obtained from commercial manufacturers and used in all sintering experiments. A comparison between microwave sintered material and identical samples sintered in a conventional electric furnace revealed …

A Multiprocessor System Using A Switch Matrix Configuration, Rabah Aoufi

Masters Theses

"This thesis describes a class of interconnection networks based on the use of a switch matrix to provide processor to memory communication. This switch allows a direct link between any processor to any memory module. The cost and performance of this network are analytically examined. The results are compared with those of a multiprocessor system using a time-shared bus configuration and it is shown that for the two extreme cases of maximum and minimum throughput, the two approaches are equivalent from a performance point of view. However, in the general case, even with a higher cost, the switch matrix provides …

Phase Relations In Magnesium Oxysulfate Cements, Ladawan Urwongse, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

Solubilities of MgO in H₂SO₄ solutions were measured and X‐ray analyses of over 100 neat cement samples were used to construct an isothermal phase diagram for the system MgO‐H₂SO₄‐H₂O at 23°±3°C. The phases MgO, Mg(OH)₂, 3Mg(OH)₂ MgSO₄·8H₂O (3·1·8), MgSO₄·7H₂O, MgSO₄·6H₂O, and MgSO₄·H₂O were stable at 23°C. The phases Mg(OH)₂· MgSO₄·5H₂O (1·1·5) and MgSO₄·4H₂O were observed but are considered to be metastable, resulting …

Autooscillations And Nonlinear Anelasticity, Manfred Wuttig, Tetsuro Suzuki

Materials Science and Engineering Faculty Research & Creative Works

In conclusion it can be stated that a novel phenomenon, a mechanical auto oscillation, has been described theoretically and shown to exist experimentally. These auto oscillations occur when a nonlinear anelastic solid is forced into large amplitude oscillations in the vicinity of a martensitic transformation. They manifest themselves as a low frequency auto modulation of the a martensitic transformation. They manifest themselves as low frequency auto modulation of the forced vibration of such a solid. © 1980.

The System Mgo‐Mgcl2‐H2o At 23°C, Ladawan Urwongse, Charles A. Sorrell

Materials Science and Engineering Faculty Research & Creative Works

Solubilities of MgO in aqueous HC1 solutions at 23°±3°C were measured and combined with analyses of neat magnesium oxychloride cements, cured in sealed containers, to construct an equilibrium phase diagram for the system MgO‐MgCl2‐H₂O. Specific gravities and acidities of solutions saturated with MgO and relative humidities of vapor phases over sealed samples were measured and combined with XRD data to define the compositions in equilibrium with two crystalline phases. Studies of relative reaction rates indicated that the 5–1–8 phase crystallizes more rapidly than the 3·1·8 phase and that cements near the 3·1·8 composition react rapidly with atmospheric CO …

The Dufour Effect. Iii. Direct Experimental Determination Of The Heat Of Transport Of Carbon Tetrachloride-Cyclohexane Liquid Mixtures, Richard L. Rowley, Frederick H. Horne

Faculty Publications

The heat of transport of carbon tetrachloride-cyclohexane liquid mixtures has been determined directly by Dufour effect experiments. The technique employs a withdrawable ''liquid gate'' to create a nonturbulent, sharp diffusional interface. The partial differential equations governing the barycentric velocity, composition, and temperature distributions are solved with a Crank-Nicholson implicit numerical scheme. This allows inclusion of the composition and temperature dependence of the thermodynamic and transport parameters. For mean mole fraction of carbon tetrachloride x1 between 0.34 and 0.55 and for mean temperature T between 295.13 and 296.43 degreesK, the best least squares fit of the data for the heat of …

Test 1355: Steiger Panther Iii Pta-325 And Panther Iv Cs-325 Diesel 10-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1358: John Deere 4640 Power Shift Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1359: John Deere 4040 Syncro Range Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1360: John Deere 4040 Power Shift Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1361: John Deere 4240 Syncro Range Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1365: Massey-Ferguson Mf210 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1366: Massey-Ferguson Mf210-4 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1368: Massey-Ferguson Mf220-4 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1371: Kubota L305 Dt Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1372: Kubota L345 Dt Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1373: White Iseki 2-30 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1374: White Iseki 2-35 Diesel 8-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1375: White Field Boss 4-175 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1377: International 3788 And 6788 Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1376: International 884 Rowcrop Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Finite Element Model Of A Timoshenko Beam With Structural Damping, Louis Ablen Roussos

Mechanical & Aerospace Engineering Theses & Dissertations

A numerical integration technique, a modified version of the Newmark method, is applied to transient motion problems of systems with mass, stiffness, and small nonlinear damping. The nonlinearity is cast as a pseudo-force to avoid repeated recalculation and decomposition of the effective stiffness matrix; thus, the solution technique is dubbed the "pseudo-force Newmark method." Comparisons with exact and perturbation solutions in single-degree-of-freedom problems and with a Gear-method numerical solution in a cantilevered Timoshenko beam finite element problem show the solution technique to be efficient, accurate, and, thus, feasible provided the nonlinear damping is small. As a preliminary step into the …

Nebraska Summary 001: Massey Ferguson 240 Diesel 8 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE

General

Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure.

The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Rubber Covered Rolls-The Nonlinear Elastic Problem, R. C. Batra

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The problem of the indentation of a rubberlike layer bonded to a rigid cylinder and indented by another rigid cylinder is analyzed. The rubberlike layer is assumed to be made of a homogeneous Mooncy-Rivlin material. The materially and geometrically nonlinear problem is solved by using the finite-element code developed by the author. Results computed and presented graphically include the pressure profile at the contact surface, stress distribution at the bond surface and the deformed shape of the indented surface. © 1980 by ASME.

Combined Heat And Lass Transfer In Mixed Confection Ower A Horizontal Flat Plate, T. S. Chen, F. A. Strobel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The combined effects of buoyancy forces from thermal and species diffusion on the heat and mass transfer characteristics are analyzed for laminar boundary layer flow over a horizontal flat plate. The analysis is restricted to processes with low concentration levels such that the interfacial velocities due to mass diffusion and the diffusion-thermo/thermo-diffusion effects can be neglected. Numerical results for friction factor, Nusselt number, and Sherwood number are presented for gases having a Prandtl number of 0.7, with Schmidt numbers ranging from 0.6 to 2.0. In general, it is found that, for the thermally assisting flow, the surface heat and mass …

Computer Aided Optimal Design Of Helical Gears, S. N. Muthukrishnan

Dissertations and Theses

A random search method for optimum design of a pair of helical gears has been developed. The sequence of optimization consists of two principal components. The first is the selection phase, where the output is the starting solution for the design variables - module, facewidth, helix angle and number of teeth on the pinion. The input for the selection phase includes the application environment, approximate center distance, minimum helix angle, desired values of gear ratio, pinion speed and the power to be transmitted. The limits on each of the design variables and the constraints are imposed interactively during the first …