Engineering Commons^™

Final Project Report: Development Of A Hydrogen Fueled Transit Vehicle, C. A. Maccarley

Electrical Engineering

No abstract provided.

Test 1441: International 5488 Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1440: International 3688 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Investigation Of Blood Pressure Measurement Using A Hydraulic Occlusive Cuff, Kusha R. Bhattarai

Dissertations and Theses

This thesis presents an improved oscillotonometric system for the measurement of human blood pressure. The study included:

1. The design of a hydraulic occlusive cuff,

2. The investigation of the wave forms taken from the blood pressure measurements, and

3. The design of a mechanism for the simulation of human blood pressure pulse.

In this study, an experimental system consisting of a rigid shell occlusive cuff, a constant volume displacement pump, a transducer, and a chart recorder was designed and used for data collection.

Test 1435: John Deere 8650 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1437: John Deere 1250 Diesel 9-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1436: John Deere 8450 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1434: John Deere 8850 Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Photovoltaic Cells: Common Power Source For Tomorrow?, Florida Solar Energy Center, Arthur Litka

FSEC Energy Research Center®

The word "photovoltaic" combines the scientific terms "photo", meaning light, and "voltaic", meaning voltage. Together, the terms mean voltage generated by light energy. Specially treated silicon, or another substance, is manufactured in such a way that when light strikes it electricity is produced. The cells have no moving parts, and they are durable. They are commonly called solar cells.

Santa Clara Magazine, Volume 24 Number 8, Spring 1982, Santa Clara University

Santa Clara Magazine

3 - A CHINA DIARY The President's log of the first Catholic delegation to visit China since Cardinal Spellman's visit in 1949. By William J. Rewak, S.J.

16 - PERSONAL FINANCIAL PLANNING A guide to handling financial affairs, especially for those just starting out. By Francis J. Corrigan.

19 - STYLE BY STRUNK Uncommon thoughts about the common language, based on Strunk and White's The Elements of Style. By James P. Degnan.

22 - PHILOSOPHICAL SKIRMISHES ON THE AIR A world-famous philosopher reminisces about some of his broadcast debates with other philosophers over the British Broadcasting Company. By Frederick C. …

Allocation Of Transportation Costs To Users, James E. Black, Jerry G. Pigman

Kentucky Transportation Center Research Report

The 1980 annual cost responsibility and user-generated revenue were determined for each vehicle class using Kentucky's highways. The incremental-cost method was selected as the procedure for assigning the responsibility for each component of the highway cost to the users. Generally, the method is based on the concept that each highway cost component can be subdivided into increments caused by vehicles of different types, sizes, and weights.

Annual costs for the highway system were based on construction, replacement or current value costs representing capital investment components of the highway. Those components were: 1) preliminary design and engineering, 2) right-of-way, 3) utilities …

Accident Rates By Vehicle Type, Joseph D. Crabtree, Kenneth R. Agent

Kentucky Transportation Center Research Report

This report describes the calculation of accident rates for different vehicle types, using vehicle-miles travelled as the measure of exposure. Rates are reported for passenger cars, single-unit trucks, combination trucks, buses, and motorcycles on various highway types. Highway types are broken down by functional classificaion, administrative classification, number of lanes, and rural or urban location. Generally motorcycles had the highest rates and passenger cars had the lowest, although this varied by highway type.

Analysis Of Saturation Flow At Signalized Intersections, Kenneth R. Agent, Joseph D. Crabtree

Kentucky Transportation Center Research Report

The accuracy of saturation flow values is of prime importance when determining the capacity of signalized intersections. The objective of this study was to collect a large sample of field measurements so that reliable saturation flow values could be obtained and the factors affecting saturation flow could be identified.

The results identified several factors which had significant influence on saturation flow. A formula was recommended for use in estimating an appropriate saturation flow value for a specific lane on an approach to an intersection. Adjustment factors were applied to a "base'' saturation flow value. Adjustments were developed for the following …

Evaluation Of Snowplowable Markers, Jerry G. Pigman, Kenneth R. Agent

Kentucky Transportation Center Research Report

The objective of this study was to evaluate available snowplowable markers under similar traffic and snowplowing operations. There were five different markers tested which included the following: 1) Stimsonite 96, 2) Dura-Brite, 3) recessed, 4) Kingray, and 5) Prismo Roadstud.

The Stimsonite 96, Dura-Brite, and recessed markers were found to be acceptable snowplowable markers. All three of these markers were found to have adequate reflectivity during both dry and wet nighttime conditions. This reflectivity was maintained over the test period and the markers proved to be durable when subjected to snowplow operations. However, considering all available input, the recessed marker …

Problem Identification For Highway Safety Plan (Fy 1983), Kenneth R. Agent, Joseph D. Crabtree, Jerry G. Pigman

Kentucky Transportation Center Research Report

An annual highway safety program is proposed each year for the State of Kentucky in order to comply with Section 402, Title 23 of the United States code. This program includes the identification, programming, budgeting, and evaluation of safety projects. This report is the fourth in a series of annual reports which have been included as the problem identification portion of Kentucky's Annual Highway Safety Plan.

The approach used in this study involved identifying problem areas related to the 18 highway safety program standards with added emphasis placed on selected areas. This resulted in the analysis of 19 problem identification …

Triaxial Compression And Permeability Tests On Dense Graded Aggregate, David L. Allen

Kentucky Transportation Center Research Report

Fifty-six dense-graded aggregate samples of crushed limestone were received from the Division of Materials. Triaxial tests and permeability tests were to be performed.

The samples were obtained from seven sources with four gradations (fine, medium, coarse, and gap) from each source and two samples of each gradation. One of the samples of each gradation was to be compacted by standard compactive effort (AASHTO T-99) and the other at modified compactive effort (AASHTO T-180). The seven sources and their identification codes are as follows:

1. Martin - Marietta (59)
2. Hopkinsville Stone (150)
3. Nally - Hayden (112)
4. Harrod - Carter (51)
5. Reed Crushed …

Brewster And Pseudo-Brewster Angles Of Uniaxial Crystal Surfaces And Their Use For Determination Of Optical Properties, M. Elshazly-Zaghloul, R. M.A. Azzam

Electrical Engineering Faculty Publications

Brewster and pseudo-Brewster angles are defined for surfaces of transparent and absorbing uniaxial crystals parallel and perpendicular to the optic axis. Two Brewster angles of a transparent uniaxial crystal surface parallel to the optic axis, measured when the optic axis is oriented perpendicular and parallel to the plane of incidence, readily determine the ordinary and extraordinary indices N_o and N_e. N_o and N_e can also be obtained from two Brewster angles measured on a surface perpendicular to the optic axis in contact with two media of different refractive indices. Conditions for the existence of two …

Modes Of A Laser Resonator With A Retroreflecting Corner Cube Mirror, Guosheng Zhou, Anthony J. Alfrey, Lee W. Casperson

Electrical and Computer Engineering Faculty Publications and Presentations

The self-consistent integral equation for the field distribution of the resonant modes in a resonator with a tilted retroreflecting corner cube mirror is solved. The corner cube acts like a convex lens with radius of curvature -L cot²Ө in the rotation direction (L is the cavity length and Ө the rotation angle) and like a flat plane in the direction of the rotation axis. The field distribution can be described in terms of Hermite-Gaussian functions, and these results have been confirmed experimentally using an Ar-ion laser. The equivalent beam matrix for a reflecting corner cube is also found.

A Unique Microprocessor Instruction Set, D. A. Fairclough

Faculty Publications

New instruction sets have been based on traditather than on the application of scientific method. Here, the latter has yielded a simple, optimal, en-member instruction set.

H & V News

Building Services Engineering

No abstract provided.

Performance Evaluation Of Brick Veneer With Steel Stud Backup, Joseph O. Arumala, Russell H. Brown

CCFSS Library (1939 - present)

No abstract provided.

Test 1432: Ford 7610 And 7710 (16x4) Diesel 8 And 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1431: Ford 6610 And 6710 (16x8) Diesel 8 And 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1433: Ford 7710 And 7610 (16x8) Diesel 8 And 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Cpacs Happenings (April 1982 Newsletter), College Of Public Affairs And Community Service, University Of Nebraska At Omaha

CPACS Newsletters

The College of Public Affairs and Community Service (CPACS) newsletter that reported on the news, collaborations, events, and general happenings of the UNO College of Public Affairs and Community Service. This newsletter has had many names and variations over the years including SPACS Newsletter (1973); Newsletter of the College of Public Affairs and Community Service (1973-1974): Happenings (1974-1980s); and the current e-newsletter titled the CPACS Collective (2021-)

A Comparative Study Of In-Core And Out-Of-Core Equation Solvers For Microcomputer Applications, Salahuddin A. Siddiqui

Retrospective Theses and Dissertations

This research evaluates the applicability to microcomputers of various methods for determining the solution of large systems of simultaneous linear algebraic equations. Such systems of equations characterize physical systems often encountered in Civil Engineering and other engineering disciplines. Many methods of solution involving either in-core or out-of-core storage of data have been developed for use with large digital computers. These methods are reviewed and their applicability to microcomputers is evaluated. A comparison of several schemes is made regarding core size required, time of execution, and precision of results. The out-of-core solution schemes for banded matrices are found to be most …

Development Of A Graphics Display Controller, David R. Hudnall

Retrospective Theses and Dissertations

The goal of this research is to define and develop a computer graphics display controller that will provide a high performance to cost ratio by employing state-of-the-art components and techniques. This report briefly defines the phrase "computer graphics display system" and the related technologies. The system requirements for a target display controller are developed and their hardware implications are presented. An architectural overview precedes a detailed explanation of all functional areas of the target system. This includes an overview of the VLSI graphic figure generator, which is the heart of the target system. Finally, the concept of hardware independent graphic …

Optimizing Growth Options For The Wewahootee Pump And Transport System, Joseph O. Lung

Retrospective Theses and Dissertations

Techniques for performance optimization and energy reduction were reviewed for application to water supply plants. Simple techniques were developed which permit intelligent management decisions for plant operation growth. The techniques were applied to the Wewahootee Water Supply Plant, Cocoa, Florida. Optimum performance for the existing plant was determined together with a growth plan for reducing energy consumption and increasing the maximum flow capacity to meet demand through the year 2000. The following recommendations were made: 1. Plant operators should incorporate the optimized pump operation schedule presented herein. 2. Four existing pumps should be modified for dual speed operation, and a …

A Dynamic Analysis Of An Explosion Driven Hydrodynamic Conical Distributed Breach Shock Tube, Lee E. Griesemer

Retrospective Theses and Dissertations

In order to better simulate an explosive underwater environment, a new design of the existing explosion driven hydrodynamic conical shock tube has been proposed. This new concept calls for the removal of part of the old tube to accommodate a distributed breach plug. The distributed breach should enhance shock wave characteristics by minimizing the energy losses associated with plastic deformations which occur at detonation. This report makes use of a finite element program, SAP IV, to investigate the modal characteristics of the new distributed breach design. A dynamic response history analysis has also been performed in order to predict the …

Evaluation Of Swale Design, David E. Anderson

Retrospective Theses and Dissertations

Swales are designed to infiltrate runoff from intermittent storm events. Present design methodologies have resulted in swales which operate under several conditions; these conditions are soil, vegetation, climatic and geographical location dependent. To attain a swale design which considers and accounts for the important factors under Florida conditions, adequate assessment of rainfall, overland, flow, infiltration and soil moisture must be given priority treatment. Several roadside and residential swales were studied and relationships were drawn for soil moisture, porosity and infiltration rates. A design methodology is included and computer modeling infiltration aids in the design.