Engineering Commons^™

Mathematical Modeling Of Carrier Mediated Mass Transfer Through Liquid Membrane Systems, Keng Chao Wang

Dissertations

Dispersed liquid membrane systems are double emulsion drops. Two immiscible phases are separated by a third phase which is immiscible with the other two phases. The liquid membrane systems were classified into three types: (1) carrier mediated mass transfer, (2) mass transfer with reaction in the receiving phase, (3) mass transfer without any reaction involved. Copper extraction, phenol removal and solvent extraction were used as typical examples for each type of the membrane systems in the derivation of their mathematical models. Models with or without the consideration of film resistances were developed and compared. The models developed in this study …

Stress In The Alveolar Bone Surrounding A Dental Implant, Jagmohan Singh Kohli

Theses

The purpose of this study is to find the stresses developed in mandibular bone due to the occlusal loading of oral endosseous blade implants. Previous work done in this area was based on the theory of "Beam on Elastic Foundation". As the width/length ratio employed is approximately 0.65, the theory of "Plate on Elastic Foundation" used in this thesis is more appropriate. The mandibular bone acts as the foundation supporting the endosseous implants.

The analysis is complicated by the fact that the implants are irregular plates of varying thickness, the foundation modulus is a variable and the occlusal loading is …

Static Dropless Flake Aligner For Producing Composite Wood Material, Gordan P. Krueger, Anders E. Lund, Roy D. Adams

Michigan Tech Patents

Apparatus are provided for forming a loosely felted mat of elongated wood flakes, the wood flakes being supported on an elongated caul. The flakes are deposited between a plurality of closely spaced parallel baffles so as to be aligned in mutually parallel relation. The caul is supported adjacent the lower edges of the baffles and is support for vertical movement to facilitate buildup of the mat. Apparatus movable back and forth along the length of the caul is provided to deposit wood flakes in an evenly dispursed manner. At least one picker wheel also moves along the length of the …

Test 1546: Case 1594 Syncromesh Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1549: Case 2096 Powershift Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1548: Case 1896 Powershift Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1547: Case 1594 Powershift Diesel 12-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Sulfur Dioxide And Particles In Quiescent Volcanic Plumes From Poás, Arenal, And Colima Volcanos, Costa Rica And Mexico, T. Casadevall, William I. Rose, William H. Fuller, William H. Hunt, Mark A. Hart, Jarvis L. Moyers, David C. Woods, Raymond L. Chuan, James P. Friend

Department of Geological and Mining Engineering and Sciences Publications

Measurements of SO₂ emission rates and concentrations and of particle distribution, size, shape, and composition were made in quiescent volcanic plumes emitted into the troposphere from Poás and Arenal volcanos, Costa Rica, and Colima volcano, Mexico. SO₂ emission rates were 700±180 metric tons per day (t/d) for Poás, 210±30 t/d for Arenal, and 320±50 t/d for Colima. The concentrations of SO₂ calculated from the COSPEC/lidar data were 5–380 ppb. Concentrations of SO₂measured directly by flame photometry were 10–250 ppb. Particles collected in the plumes with a quartz crystal microbalance impactor were mostly less than 3 …

Test 1545: Allis-Chalmers 6070 And Deutz-Allis 6070 Deisels 12-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Bonsall Faa Report, Charles A. Bonsall

Robert "Bob" Twiggs STEM Education Collection

The Federal Aviation Administration report related to the NUSAT system from Charles A. Bonsall from October 18, 1984.

Functional Philosophy Of The Nusat System And The Organization That Developed It, Charles A. Bonsall

Robert "Bob" Twiggs STEM Education Collection

A report composed by Charles A. Bonsall titled "Functional Philosophy of the NUSAT System and the organization that developed it" from October 18, 1984.

Self-Flushing Piston Assembly For Slurry Pump, David T. Kao

Civil Engineering Faculty Patents

A slurry pump is provided having a self-flushing piston assembly mounted in a mating cylinder. The piston assembly includes a first piston having a peripheral sealing member and a reciprocating piston rod for driving the first piston for pumping action. A second piston mounted adjacent to the first piston includes a sealing member and forms an enclosed chamber with the first piston. A lost motion coupler connects the pistons together and varies the size of the chamber. On the return stroke of the piston assembly, flushing liquid on the non-slurry side is sucked into the chamber as the chamber expands. …

Multiple Determination Of The Optical Constants Of Thin-Film Coating Materials, D. P. Arndt, R. M.A. Azzam, J. M. Bennett, J. P. Borgogno, C. K. Carniglia, W. E. Case, J. A. Dobrowolski, U. J. Gibson, T. Tuttle Hart, F. C. Ho, V. A. Hodgkin, W. P. Klapp, H. A. Macleod, E. Pelletier, M. K. Purvis, D. M. Quinn, D. H. Strome, R. Swenson, P. A. Temple, T. F. Thonn

Electrical Engineering Faculty Publications

The seven participating laboratories received films of two different thicknesses of Sc₂O₃ and Rh. All samples of each material were prepared in a single deposition run. Brief descriptions are given of the various methods used for determination of the optical constants of these coating materials. The measurement data are presented, and the results are compared. The mean of the variances of the Sc₂O₃refractive-index determinations in the 0.40–0.75-nm spectral region was 0.03. The corresponding variances for the refractive index and absorption coefficient of Rh were 0.35 and 0.26, respectively.

Test 1544: Steiger Panther Iv Cm-360 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1542: Steiger Bearcat Iv Km-225 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1543: Steiger Panther Iv Km-325 Diesel 20-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Design Of Automotive Structural Components Using High Strength Sheet Steels - Structural Behavior Of Beam Webs Subjected To Web Crippling And A Combination Of Web Crippling And Bending, Chiravut Santaputra, Wei-Wen Yu

CCFSS Library (1939 - present)

INTRODUCTION In recent years, high strength steels have been used in automotive structural components to achieve weight reduction while complying with Federal safety standards. The current design recommendations, the "Guide for Preliminary Design of Sheet Steel Automotive Structural Components" 1 was issued by American Iron and Steel Institute (AISI) in February 1981. It was recommended for application to materials with yield strength up to 80 ksi. These design expressions are based primalily on the 1968 Edition of the AISI "Specification for the Design of Cold-Formed Steel Structural Members" 2 which was written for the design of buildings. The AISI Specification …

Manual Of Safety Practices, Rack Manufacturers Institute

Rack Manufacturers Institute (RMI) Specifications and Manuals (1984 - 2012)

No abstract provided.

Bulletin - October, 1984, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A four page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Acuta Enews October 1984, Vol. 13, No. 10

ACUTA Newsletters

In This Issue

TELEPHONE MANAGEMENT SYSTEMICS

WASHINGTON PERSPECTIVE

BITS & PIECES

Estimation Of Equivalent Axleloads: Computer Program Documentation, John M. Salsman, John A. Deacon

Kentucky Transportation Center Research Report

The estimation of equivalent axleloads (EAL) requires the correlation of several data bases. Described herein are three computer programs which summarize truckweight data and classification data, and combine the two data bases to estimate EAL's for each site where classification counts are available in a given year.

The programs also present the data in two matrices to characterize the effects that geographic area, federal-aid classification, coal-haul volume and total volume have on each of the traffic parameters necessary to compute EAL's.

Jackson Purchase Parkway Pavement Study, James H. Havens

Kentucky Transportation Center Research Report

Four distinct patterns of cracking were found. Temperature cracks are transverse and occur at intervals of about 15 to 88 feet. Roller-induced cracking has been made apparent by weather and erosion. Longitudinal cracking is usually at the edges of the wheel paths where rutting is prominent. Map cracking or checkering in the wheel paths is caused by the maximum shear stresses occurring at a depth equal to 1/3rd the radius of the loaded area (tire print). This cracking penetrated about 2.5 inches. This cracking and weakness was found only in the all-gravel asphaltic concrete. No stripping was found, but evidences …

Water-Induced Surface Failures On I 65, Hardin County, Kentucky, Ellis G. Williams, Herbert F. Southgate, Robert C. Deen

Kentucky Transportation Center Research Report

This report documents an investigation of water-related distress on portions of I 65 in Hardin County, Kentucky, on Muldraugh Hill. An open-graded surface placed on a full-depth asphaltic concrete pavement had shown areas of flushing and shallow shear failures in the outer lanes after one year of service. Cores were obtained from the outer lanes in areas exhibiting no problems to shear and flow failures. Core sites also were chosen across the lane to represent edge, wheel track, and between wheel track conditions. Visual inspection of the cores was made under normal lighting and an ultraviolet light and photographs were …

Oxygen Activity Dependence Of The Defect Structure Of La-Doped Batio3, M. M. Nasrallah, Harlan U. Anderson, A. K. Agarwal, B. F. Flandermeyer

Materials Science and Engineering Faculty Research & Creative Works

A model for the behavior of donor doped BaTiO₃ as a function of oxygen activity is proposed. Thermogravimetric measurements show good agreement with the proposed model. The results show that donor-doped BaTiO₃ is stoichiometric with electronic compensation of the donor at low oxygen activity, but with increasing oxygen activity, compensation becomes ionic as excess oxygen is absorbed. The possible compensation mechanisms are discussed. © 1984 Chapman and Hall Ltd.

Pavement Cuts For Utilities - A Guide For Their Management, James Mabry Iddins, Charles F. Scholer

Indiana Local Technical Assistance Program (LTAP) Publications

A manual of street cut methods that have worked well for several states, cities & counties.

Pavement Cuts For Utilities - A Field Guide To Their Accomplishment And Maintenance, James Mabry Iddins, Charles F. Scholer

Indiana Local Technical Assistance Program (LTAP) Publications

A guide to developing specifications and procedures for road maintenance.

Effect Of Wall Temperature Control On Low-Speed Axisymmetric Body Drag, John C. Lin

Mechanical & Aerospace Engineering Theses & Dissertations

This paper presents results of a numerical study of the effect of wall temperature control on the low speed aerodynamic drag of axisymmetric bodies at turbulent Reynolds numbers and zero angle of attack.

Results for both skin-friction and pressure drag were computed for slender bodies using first-order viscous-inviscid interaction theory. Computations using boundary-layer theory were conducted to evaluate the effect of wall heat transfer on bluff-body separation control. Wall heat transfer with 100 percent surface coverage (for all bodies) as well as some partial surface coverage cases were investigated. The wall-to­ tota1-freestream temperature ratio was varied between 0.08 and 2. …

Investigation Of Flow Phenomena In A Repetitively-Pulsed Gas Flow Switch, Shivakumar Srinivasan

Mechanical & Aerospace Engineering Theses & Dissertations

A two-dimensional, unsteady numerical model for analyzing the characteristics of gas flowing through a gas blown spark gap switch has been developed. The computational model is governed by the conservation equations of mass, momentum and energy in an inviscid, non-conducting, perfect, compressible fluid. The governing equations have been solved by using MacCormack's finite volume technique. The effects of rapid gas heating and subsequent changes in the fluid properties of the gas are examined in the high-pressure spark gap switch. The gas temperature, expansion velocity, density and pressure are calculated as functions of time. Air is the dielectric flowing through the …

Design Of Infrasound-Detection System Via Adaptive Lmstde Algorithm, Camille S. Khalaf

Electrical & Computer Engineering Theses & Dissertations

A proposed solution to an aviation safety problem is based on passive detection of turbulent weather phenomena through their infrasonic emission. This thesis describes a system design that is adequate for detection and bearing evaluation of infrasounds. An array of four sensors, with the appropriate hardware, is used for the detection part. Bearing evaluation is based on estimates of time delays between sensor outputs. The generalized cross correlation (GCC), as the conventional time-delay estimation (TOE) method, is first reviewed. An adaptive TUt approach, using the least mean square (LMS) algorithm, is then discussed. A comparison between the two techniques is …

Groundwater Management By Linear Programming, Seungho Song

Civil & Environmental Engineering Theses & Dissertations

Three hydraulic optimization models are developed. These models combine the finite difference equations of two-dimensional groundwater flow in composite aquifers with various linear programming techniques. The hydraulic submodel employed in these hydraulic optimization models is so versatile that it accounts for time varying pumpage, leaky artesian conditions, a variety of boundary conditions, induced infiltrations from streams or rivers, and conversion from artesian to water table conditions. The objective of submodel 1 is to maximize the total hydraulic head from pumping wells at the end of a study period. The objective of submodel 2 is the same as submodel 1, but …