Engineering Commons^™

Investigation Into The Feasibility Of Burning Hazardous Waste In Utility Boilers, Reuben Steinberg

Theses

Disposal of hazardous waste is of major concern in recent years in this country. Declining availability of landfills together with more stringent State and Federal regulations has necessitated the need to consider alternative means of hazardous waste disposal. It was suggested that burning hazardous wastes in presently operating utility boilers might be beneficial to the utilities and offer a solution to this social problem.

This thesis investigates the feasibility of this alternative given the technical, economic and regulatory considerations involved and discusses the findings of adopting this technology for hazardous waste disposal.

Based on the results of this study it …

Graphic Display Of Robot Kinematics, Ramamurthy Vishwanathan

Theses

This thesis uses the HOUIE.BYLI graphics software package to simulate the kinematics of a six degree of freedom, MAKER I robot. The coordinate frames for the various links of the robot were established. The kinematic equations for the manipulator were developed snd solved using the techniques of inverse geometric transformations and transformations of objects in 3D space. A program was also developed to calculate the joint variables of the manipulator given any point on, and the orientation of, an object. These variable values are used to direct the robot end effector to the given point. This can be seen in …

Similitude Analysis Of Model Experiments Of Piles Driven To Rock, George Nicou Georghoudes

Theses

This thesis investigates the similitude requirements for the Dynamic Pile Driving Apparatus in the New Jersey Institute of Technology Laboratory. The apparatus is being used to perform model tests to study bearing stratum fracturing caused by driving pile groups to weak rock.

Two approaches were used to establish similitude between the model and actual field conditions. The first approach utilizes dimensional analysis to develop a relationship between the energy delivered to the rock mass by the pile and the unit length. The second approach proposes a procedure to establish an empirical relationship between the threshold energy to fracture the rock …

On Natural Frequency Of The Stiffened Hvac Ducts, Jin-Lian Ha

Theses

This thesis employs ANSYS program to calculate the natural frequency of a stiffened HVAC duct and to investigate the affect of these stiffeners to the values of the natural frequency.

Investigation through this thesis shows that increases in the number of transverse stiffeners mould increase the natural frequency of the HVAC duct and the installation of the axial stiffener mould also increase the duct natural frequency.

The Impact Of Fms On Batch Production Processes, Jan-Sheau Ho

Theses

A Flexible Manufacturing System (FMS) is an integrated system of combining metalcutting and other processes with materials handling under computer control. With computer control, FMS is capable of processing a variety of different types of workpieces simultaneously. FMS is an approach towards a balancing of high output on the one hand and great flexibility on the other hand. FMS stands as a new technology to improve the productivity of mid-volume, mid-variety production; therefore the manufacturing world will soon feel the impact of FMS.

This thesis attempts to specify what FMS is and how it works, the influence of FMS on …

Electrochemical Reduction Of Quaternary Ammonium Salts, Rudolph K. Kapichak

Theses

The electrochemical reduction of two highly hindered quaternary ammonium salts was attempted. The reductions were performed in hexamethylphosphoramide at a controlled potential using platinum electrodes. It was anticipated that these reductions would provide a route to the formation of anti-Bredt bridgehead olefins. This work is an extension of the work of Dubois, Monvernay and Lacaze who electrochemically reduced quaternary ammonium salts such as trimethyl-t-butylammonium iodide (XX).

Trimethy1-2,4,4-trimethy1-2-pentylammonium iodide (XXIII) was reduced to form 2,4,4-trimethyl-l-pentene (XXVI) and 2,2,4-trimethylpentane (XXV). The yields of the two runs of this reduction were 10% and 20% and in the first run of the reduction 75% …

Optimization Of Reactive Ionized Cluster Beam (R-Icb) Technique For Deposition Of Gan Films, Veronica S. Kyriacou

Theses

The deposition of GaN film onto glass substrate, using the Reactive - Ionized Cluster Beam deposition technique was studied. The creation of clusters is dictated by various parameters such as the vacuum pressure inside and outside the crucible, the crucible temperature, and the nozzle diameter of the crucible. Optimization of these parameters was experimentally studied, and deposition of gallium films on glass substrates was tried as a first step.

The direct heating method was used at first to get the 1100¬1300°C crucible temperature which was required for the creation of gallium clusters. Although different tungsten wire diameters and different number …

The Gpib User's Manual For Hx-40, Ding-Tang Li

Theses

A completed RS-232 to GPIB interfacing system has been built for HX-40 to master the GPIB oriented machine through its serial port. GPIB commands and data can be transfered between HX-40 and the slave station, which is a HP 3582A spectrum analyzer in this project. The data acquisition from serial to GPIB is done by a well-made GPNET mode 10 interfacing board in a transmitting rate of 9600 baud rate. GPNET exchanges data and commands with HX-40 through a RS-232 port, and passes them to the slave station through a GPIB port which is coordinated by GPIB protocol. A software …

Optimum Design Of Structures Subject To Buckling Constraints, Thomas G. Looby

Theses

This thesis describes the optimal design of bar type planar truss structures subject to stress and buckling constraints. All of the structures considered are modeled using the direct stiffness finite element approach. A mathematical programming method incorporating a feasible directions routine is utilized to develop least weight designs for these conditions. The existing structural optimization programme CADOS which has successfully solved stress and deflection problems for this class of structures is adapted herein to treat local stability constraints based on Euler bucking criteria.In addition the optimization routine is modified to more effectively treat, infeasible starting designs. These modifications were tested …

Sputtered Mercury Cadmium Telluride Heterojunction Devices : Electrical Characteristics And Fabrication Process, Ashish N. Mistry

Theses

The main objective of this thesis was to grow high quality epitaxial films of the compound semiconductor Mercury-Cadmium-Telluride (MCT) on Silicon and MCT substrates,using sputtering technology. The research was aimed at investigating the heterojunction behaviour at such interfaces. Detailed studies about the heterojunction theory were made. Devices were made using MCT substrates prepared at the Santa Barbara Research Center (S.B.R. C.),California.

Experiments were designed to grow MCT films with high electron mobility and low carrier concentration in as-grown MCT films and some results were obtained close to reported data for high grade bulk material. Since the parameters involved in sputter …

The Interfacing Between The A/D Converter, Buffer Memory And Hx-40 Microcomputer, Yu-Hwa Chu

Theses

The data acquisition system which includes A/D converter, buffer memory, and address generator, is to digitize the signal for the computer use. The special feature of this system is the computer controlled digitizing rate over a range from 35K to 0.

The interfacing between Motorola 68000 E.C.B. to H.P. 64000 Development System is the simple example for data communication. How to make the protocal to be compatible is the main point. H.P. 64000 is treated as a host computer because it has the capability for data management and large memory for storing data.

Finite Element Analysis Of The Prosthetic Acetabular Region, Katkuri Venkat Rammanohar Reddy

Theses

Femoral component loosening and prosthetic stem fractures have renewed interest in conservative alternatives to conventional total hip replacements. The objective in this study is to get interfacial stresses of a acetabular surface replacement cup. This is done by performing finite element analysis of the model. A solid three - dimensional model with a grid of 3D isoparametric solid elements is generated using ANSYS, a powerful finite element analysis package. The stiffness is considered to be linearly proportional to the stress in the acetabular region. The stresses are determined by performing iterative finite element analysis. Stresses arp computed using two different …

Digital Signal Processing On Tms32010 Evaluation Module And Analog Interface Board, Jiming Sun

Theses

The TMS32010 Evaluation Module (EVM) and Analog Interface Board (AIB) have been used to implement a digital signal processing system. This new system will be the hardware basis for research and development in the DSP field at NJIT in the future. This thesis will serve as a user's guide and overall technical manual for the system.

TMS32010 Assembler, Linker and Simulator in VAX-11 are used to develop the system software, then we can down load the object codes to the EVM through the MODEM in order to test them. By using the A/D and D/A converter as input and output …

Microcomputer-Based System For The Measurement Of Facial Swelling, Michael Guy Demuth

Theses

The measurement of facial swelling after oral surgery can indicate the effect of anti-inflammatory drugs. A mechanical device was interfaced to a microcomputer to allow faster calculation of swelling. The mechanical system first established X and Y coordinates on the face. A feeler arm traced out the facial contours and two linear variable differential transformers (LVDTs) related X and Y displacements to voltages which were fed into a microcomputer via an A/D converter. Three BASIC programs were written which facilitated the analysis of patient swelling. MEASUREMENT stored the X-Y voltages from the LVDTs in a patient disk file. CALCULATION filtered …

Design And Construction Of An Atomic Nitrogen Source For Ion Cluster Beam Deposition Of Thin Film Nitrides, Sahar Elgharib

Theses

The objective of this thesis research was to generate atomic nitrogen to react with Ga being deposited by an Ion Cluster Beam method to prepare GaN thin films. An experimental reactor was designed and constructed to generate atomic nitrogen by making use of a microwave induced discharge to dissociate molecular nitrogen into atomic nitrogen. The concentration and the flow rate of the atomic nitrogen arriving at the substrate were measured by titration with nitrous oxide. The experiments were done with 0.32 square cm quartz tubing at room temperature over the nitrogen pressure range from 0.14 torr to 0.56 torr. Results …

Effects Of Adhesion On The Active Pressure Exerted On A Retaining Wall, Thomas G. Gallagher

Theses

This paper investigated the effect of adhesion on the active pressure behind a retaining wall. No equation existed to solve for the active pressure for a sloped backfill that also takes into consideration cohesive and adhesive forces on a failure wedge. The trial—wedge solution(Culmann method) considers these parameters, but since it is a trial and error method it takes up too much time to solve. A shorter solution is desirable. An equation for the active pressure in terms of ρ(angle between horizontal and failure plane) was derived. A closed form solution for earth pressure was developed by setting the derivative …

Dynamic Laryngeal Analysis : Hardware And Software, Augustine Chan

Theses

A data acquisition and analysis system has been built and tested for the study of laryngeal dynamics: The system uses a computer to control the digitizing rate and to coordinate the pitch prompting for the subject. Tokens of steady state laryngeal vibration are obtained from an electroglottograph when the subject intones a series of computer prompted pitches in a musically scalar sequence. The system digitize the data at a basic rate of 200 samples per laryngeal cycle: This procedure enables the system to perform a modal analysis of laryngeal function: The signal processing and analysis procedure developed displays voice registration …

Cold-Formed Steel Design Manual, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Acuta Enews January 1986, Vol. 15, No. 1

ACUTA Newsletters

In This Issue

President's Message

Shared Tenant Services at Colleges and Universities

Can you hear me?

Party Line

New Product

The University of Central Florida

Telephone Registration

Tradition, Innovation And Conflict: Perspectives On Colorado Water Law, Lawrence J. Macdonnell

Books, Reports, and Studies

This digital resource contains only an abstract, cover image and table of contents information from the published book.

Print copy of book is available in the University of Colorado’s Wise Law Library: http://128.138.161.92/record=b129217

Contents: Introduction / Lawrence J. MacDonnell -- PART ONE : THE BACKGROUND: Meeting Colorado's water requirements : an overview of the issues / David H. Getches -- The historical development of Colorado water law / Raphael J. Moses -- PART TWO : WATER RIGHTS ADJUDICATION AND ADMINISTRATION: Administering Colorado's water : a critique of the present approach / Clyde O. Martz, Bennett W. Raley -- Water administration …

Summer 1986, 90.9 Wmpg Fm

WMPG Program Guides

"Alternative music to soothe the savage soul"

Summer 1986, 90.9 Wmpg Fm

WMPG Program Guides

WMPG Program Guide, Summer 1986.

One sheet w/ letter

Winter/Spring 1986, 90.9 Wmpg Fm

WMPG Program Guides

WMPG Program Guide, Winter/Spring 1986

Finite Element Analysis Of Multipass Effects Of Vehicles On Soil Compaction, David Pollock, J V. Perumpral, T Kuppusamy

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Finite element procedure was used to simulate multiple wheel loading and to predict its effect on soil compaction. Results of nonlinear analysis, conducted using an incremental loading procedure, show effects of tire size, soil type, and number of passes on soil compaction. The results of the study also demonstrate the potential use of the procedure in compaction related studies. However, experimental verification of the model is necessary before the procedure can be recommended for wider use.

State-Feedback Control Of Non-Linear Systems, Stanislaw H. Żak, Carl A. Maccarley

Electrical Engineering

A design method for state-feedback controllers for single-input non-linear systems is proposed. The method makes use of the transformations of the non-linear system into ‘controllable-like’ canonical forms. The resulting non-linear state feedback is designed in such a way that the eigenvalues of the linearized closed-loop model are invariant with respect to any constant operating point. The method constitutes an alternative approach to the design methodology recently proposed by Baumann and Rugh. Also a review of different transformation methods for non-linear systems is presented. An example and simulation results of different control strategies are provided to illustrate the design technique.

Differentiation Of Murine Erythroleukemic Cells During Exposure To Microwave Radiation, Roger F. Brown, S. V. Marshall

Biological Sciences Faculty Research & Creative Works

Cultures of murine erythroleukemic cells undergoing erythroid differentiation in response to induction by hexamethylene bisacetamide (HMBA) were exposed to 1180-MHz microwave (MW) radiation for 48 h while maintained at 37.4°C by variable-temperature air flow. Exposures at 1180 MHz were at 5.5, 11, and 22 mW/cm2 with a normalized specific absorption rate of 3.32 W/kg per mW/cm2. HMBA-induced control cells were incubated in a 37.4°C water bath. Mean cell doubling time was 16.5 h in both the irradiated cultures and the control cultures. About 65% of the cells of irradiated cultures and control cultures were benzidine-positive differentiated cells. Both the irradiated …

Bulletin - January, 1986, Civil Aviation Medical Association

Browse all Civil Aviation Medical Association Newsletters

A six page newsletter of the Civil Aviation Medical Association. The newsletter provided news about civil aviation medicine and information related to the organization.

Missouri National Recreational River Gavins Point Dam To Ponca, Nebraska Streambank Erosion Rate Study For The Period 21 April, 1978 To 10 August, 1985

United States Army Corps of Engineers, Omaha District

This report is to document the procedures used and the results obtained fram the bank erosion study for the Missouri National Recreational River Gavins Point Dam to Ponca, Nebraska. The period studied extends fram 21 April, 1978 to 10 August, 1985 or a period of 7.31 years. The study was made for the Omaha District of the U. S. Army Corps of Engineers by River Pro's under Contract No. DACW45-85-D-0084.

Convection In The Oceanic Crust' Simulationo F Observationsf Rom Deep Sea Drilling Project Hole 504b, Costa Rica Rift, Colin F. Williams, T. N. Narasimhan, Roger N. Anderson, Mark D. Zoback, Keir Becker

United States Department of Energy: Publications

Three-dimensional modeling of convection in the oceanic crust at Deep Sea Drilling Project site 504B using an integral finite difference model reasonably duplicates underpressures, surface heat flow, downhole temperature profiles, and fluid drawdown rates observed by in situ measurements in the borehole. The major constraint to produce such good fits is the permeability versus depth function,a quantity which was actually measured in the borehole. Pronounced "underpressuring" (fluid pressures less than hydrostatic) occurs throughout the convection cell if and only if a tight, nearly impermeable cap rock (chert) exists over the cell. The computed flow rates of water from the ocean …

Moderating Online Conferences, Revised Manuscript, Computerized Conferencing & Communications Center, Elaine B. Kerr

Computerized Conferencing and Communications Center Reports

While considerable lore has accumulated about effective leadership techniques for groups interacting electronically, until now it has not been systematically presented. This material is culled from the experiences of those who have moderated past online conferences, the knowledge common to the EIES User Consultants, and observed behavior from thousands of conferences convened on EIES in the past. While this is a system-specific guide, the general principles ought to be generalizable to other systems, with different structures for group discussion.

Robert Burns put it well:
The best laid schemes o' mice and men
Gang aft a-gley;
An' lea'e us nought but …