Engineering Commons^™

Test 1648: Ford 8830 Powershift Diesel 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1650: Case International 9240 Diesel And Steiger 9240 Diesel 12-Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1653: Caterpiller Challenger 65b And 65c Diesel 10-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nebraska Summary: S125 Massey Ferguson 3670, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S120 Ford Versatile 946, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S111 Lamborghini 115 Vdt, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S103 Ford 3930 8x8, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S100 John Deere 3055, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Toughening Mechanisms In Weak Matrix Ceramic Composites, Jowoong Ha

Doctoral Dissertations

"Tough behavior of ceramic matrix composites is closely related to the weak interface between fiber and matrix. The weak interfaces in composites have been provided by reducing the chemical bonding and the residual thermal stresses between constituents. A new way to introduce the weak interface by induced porosity or damaged zones, so called porosity toughening or damage toughening respectively, was proposed in this study to provide the rationale for guiding development of oxide/oxide composites. The existence of porosity toughening was examined by qualitative theoretical consideration and experiments. Porous oxide/oxide composites were fabricated using alumino-silicate fibers (Nextel 440) and magnesium alumino-silicate …

Nmr Imaging Of Salt-Water Ice, W. Edelstein, E. Schulson

Dartmouth Scholarship

Salt-water ice was imaged in a 2Tesla, horizontal 310 mm bore NMR imaging system at 85 MHz. 50 mm diameter ice cylinders were placed in a temperature-controlled chamber in the NMR system and imaged at temperatures from −20° to 0°C. Paramagnetic Cu2SO4 at a low concentration was added to the solution, from which one ice sample was crystallized in order to decrease the NMR relaxation time of the entrapped brine in the ice cylinder and thereby speed up image acquisition. The Cu2SO4-spiked sample displayed what appears to be small brine pockets/channels which resemble larger drainage channels seen in thin plates …

Kentucky Traffic Accident Facts 1991 Report, Kentucky State Police

Kentucky Transportation Center Research Report

KENTUCKY'S TRAFFIC ACCIDENT FACTS report for 1991 is based on accident reports submitted to the Accident Unit housed in the Kentucky State Police Information Services Branch, Records Section. As required by Kentucky Revised Statutes 189 .635, "every law enforcement agency whose officers investigate a vehicle accident of which a report must be made ... shall file a report of the accident ... within ten days after investigation of the accident upon forms supplied by the bureau." The stated purpose of this requirement is to utilize data on traffic accidents" for such purposes as will improve the traffic safety program in …

A Mathematical Model Of A Sealed Nickel-Cadmium Battery, Deyuan Fan, Ralph E. White

Faculty Publications

A mathematical model for the charge and discharge of a sealed nickel-cadmium (Ni-Cd) battery is presented. The model is used to study the effect of transport properties of the electrolyte and kinetic parameters of the electrode reactions on the cell performance during the charge and discharge period. The model can also be used to demonstrate the changes of cell performance during cycling. Some comparisons between model predictions and experimental results indicate that the model predictions appear to fit the experimental data well. Sensitivity analyses illustrate that the sealed nickel-cadmium battery operates under activation control. It is also shown theoretically that …

Precipitation, Inter-Event Dry Periods, And Reuse Design Curves For Selected Areas Of Florida, Martin Wanielista

BMP Trains Research and Publications

No abstract provided.

A Nuclear Fragmentation Energy Deposition Model, John W. Wilson, D. M. Ngo, T. N. Forgarty, W. W. Buck

Mining Engineering Faculty Research & Creative Works

A formalism for target fragment transport is presented with application to energy loss spectra in thin silicon devices. A nuclear database is recommended that agrees well with the measurements of P.J. McNulty et al. (1980) using surface barrier detectors. High-energy events observed by P.J. McNulty et al. (1981), which are not predicted by intranuclear cascade models, are well represented by this work

Disintegration Of Wood, Marian Mazurkiewicz

Mining Engineering Faculty Research & Creative Works

Disintegration of a body of organic material involving subjecting the body to liquid jet action with the energy of the liquid as it impacts on the body such as to effect disintegration of the body into particles.

Using Optimization And Simulation Techniques To Estimate Initial Weevil Populations, Kunter S. Akbay

Mechanical Engineering Faculty Research and Publications

In this paper, a mathematical programming and simulation method is used to estimate the number of weevils (Neochetina bruchi Hustache, and N. eichhorniae Warner) necessary to initialize the INSECT model which simulates the biological control of waterhyacinth by the weevils. The objective is to estimate the initial input values for the adult population so that the sum of the absolute differences between the observed and the simulated numbers of weevils is minimized. In general, the simulated values using the initial values obtained from the mathematical programming problem were within the 95% confidence intervals of the actual field observations. Also, in …

A Computer Simulation Model Of Waterhyacinth And Weevil Interactions, Kunter S. Akbay, F. G. Howell, J. W. Wooten

Mechanical Engineering Faculty Research and Publications

A personal computer simulation model termed "INSECT" has been developed to evaluate biological control of waterhyacinth (Eichhornia crassipes (Mart.) Solms.) by two species of weevil (Neochetina eichhorniae Warner, and N. bruchi Hustache). The model results were compared with the data from three different locations. For each data set, the simulated plant biomass, adult and larva populations were plotted against the 95% confidence intervals of the actual field observations. In many cases, the simulation results were within the 95% confidence intervals, and especially during the growing season, they indicated trends similar to those seen in the field data. However, there were …

Design Of Robust Controllers For Gas Turbine Engines, D. E. Moellenhoff, Vittal S. Rao, C. A. Skarvan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper describes robust controller design methodologies for gas turbine engines. A linear state variable model for the engine is derived using partial derivatives. The Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) and the Parameter Robust Linear Quadratic Gaussian (PRLQG) robust controller design methodologies have been used to design a controller for gas turbine engines. A new method is proposed by combining the features of LQG/LTR and PRLQG methods and yields good robustness properties with respect to both unstructured uncertainties in the frequency domain and structured parameter variations in the time domain. The new procedure is illustrated with the …

Matrix Cracking In Laminated Composites: A Review, Serge Abrate

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This article presents an overview of the problem of matrix cracking in laminated composite materials. The parameters governing the onset and accumulation of internal damage under several types of loadings are reviewed. The analysis of laminates with matrix cracks can be performed using a shear-lag model, variational, elasticity, finite element or finite difference approaches. Prediction of further cracking is based on either a fracture mechanics approach or a probabilistic failure strength theory. Continuum damage mechanics are used by some investigators to model the behavior of the cracked laminate. Recent developments in this area are summarized here, and suggestions for future …

Linear Interpolation Lattice, Cameron K. Coursey, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

The Well-Known Analysis and Synthesis Filters of Linear Prediction Theory Are Extended Here to Include Linear Interpolation. © 1991 IEEE

Dynamic Adiabatic Shear Band Development In A Bimetallic Body Containing A Void, R. C. Batra, Z. G. Zhu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

We study the problem of the initiation and subsequent growth of a shear band in a thermally softening viscoplaslic prismatic body of square cross-section and containing two symmetrically placed thin layers of a different viscoplastic material and an elliptical void at the center. The yield stress of the material of the thin layer in a quasistatic simple compression test is taken to be either five times or one-fifth that of the matrix material. The body is deformed in plane strain compression at a nominal strain rate of 5.000 s '. These deformations are assumed to be symmetrical about the centroidal …

Toward The Optimization Of Cell Operator Productivity In Computer Integrated Manufacturing, David Leonard Gobeski

Dissertations and Theses @ UNI

Computer integrated manufacturing (CIM) has been seen as the answer to maintaining the lead in American productivity. The cell operator was seen as being critical to the success of CIM. The design of the operator's job was seen as very important. As manufacturing engineers design cell jobs, including the roles and tasks, with the operators, it was believed important for the engineer to know what motivated the cell operator. However, past studies of supervisors and their subordinates have shown that supervisors are unable to predict the importance of the elements of job enrichment of the subordinates. It was questioned whether …

Surface Treatment Of Cast Iron By Adding Different Alloying Elements To Form Metallic Glass Structure Layer Using An Industrial Carbon Dioxide Laser, Mohammad Riahi

Dissertations and Theses @ UNI

Wear and corrosion are the two factors that make utilization of metals very costly. Extraordinary amount of time and money is spent to replace metallic parts affected by either wear or corrosion. Cast iron that is used very widely in a host of different industrial products is one such metal. Among the various methods used to improve the properties of metals, production of amorphous metals is highly noticeable. This process is done by treating the base metal in a certain technique which produces a metal that is more resistant to wear and corrosion.

This study was conducted to examine the …

An Analysis Of Reinforced Concrete Composites Utilizing Recycled Polyethylene Terephthalate Thermoplastic, Jaroslav V. Vaverka

Dissertations and Theses @ UNI

Removing plastic from landfills does not solve the solid waste problem entirely. Plastic products are difficult to recycle because, unlike aluminum or glass, the plastics used in food packaging cannot be reused for the same purpose. Among the commonly used plastic resins, polyethylene terephthalate (PET) has been widely adopted by the packaging industry. This research study was concerned with recycling of PET thermoplastic in concrete as a way to reduce the volume of solid waste.

Current surveys of recycling efforts reveal that existing PET recycling approaches have become inadequate. Solid waste management is stressing the eminent need for new recycling …

Security Assessment Using Neural Computing, Badrul H. Chowdhury, B. M. Wilamowski

Electrical and Computer Engineering Faculty Research & Creative Works

The advantage of fast computation capability of an artificial neural network (ANN) is used to introduce an iterative scheme for security assessment of power systems. Two related approaches are shown which demonstratedly work satisfactorily. The idea of feedback in a single-layer feedforward neural network is experimented yielding higher accuracy. The ANN is trained by using a set of data obtained from off-line analysis of the power network. After training, an approximate solution for a given condition may be found almost immediately. The approximate solution obtained is judged adequate for assessing the security of the power system. A case study is …

A Hybrid Optoelectronic Art-1 Neural Processor, Donald C. Wunsch, T. P. Caudell

Electrical and Computer Engineering Faculty Research & Creative Works

Summary form only given. A new implementation of ART-1 (adaptive resonance theory) has been proposed that efficiently combines optical and electronic devices. All parallel computations are performed by the optics, while serial operations are performed in electronics.

A Laboratory Investigation Of Electro-Optic Kerr Effect For Detection Of Electric Transmission Line Faults, Badrul H. Chowdhury, E. Grigsby, T. J. Englert

Electrical and Computer Engineering Faculty Research & Creative Works

A prototype Kerr cell has been constructed and tested for detecting and identifying faults by monitoring high voltages such as are found in electric power delivery systems. Simulated faults were generated under laboratory conditions and monitored by the Kerr cell. Preliminary analysis was done using analog-to-digital conversion of the detected waveforms with a single board microprocessor serially interfaced with a personal computer. The occurrence of faults is readily observed and results indicate that identification of fault types can be accomplished within less than one cycle of a standard sixty-cycle-per-second delivery system. With a dedicated analysis system such a technique may …

A Neural Architecture For Unsupervised Learning With Shift, Scale And Rotation Invariance, Efficient Software Simulation Heuristics, And Optoelectronic Implementation, Donald C. Wunsch, D. S. Newman, T. P. Caudell, R. A. Falk, C. David Capps

Electrical and Computer Engineering Faculty Research & Creative Works

A simple modification of the adaptive resonance theory (ART) neural network allows shift, scale and rotation invariant learning. The authors point out that this can be accomplished as a neural architecture by modifying the standard ART with hardwired interconnects that perform a Fourier-Mellin transform, and show how to modify the heuristics for efficient simulation of ART architectures to accomplish the additional innovation. Finally, they discuss the implementation of this in optoelectronic hardware, using a modification of the Van der Lugt optical correlator

Hierarchical Neurocontroller Architecture For Intelligent Robotic Manipulation, Xavier J. R. Avula, Luis C. Rabelo

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A hierarchical neurocontroller architecture consisting of two artificial neural network systems for the manipulation of a robotic arm is presented. The higher-level neural system participates in the delineation of the robot arm workspace and coordinates transformation and the motion decision-making process. The lower one provides the correct sequence of control actions. The capabilities, including speed, adaptability, and computational efficiency, of the developed architecture are illustrated by an example.

Decoupled Dynamics For Control And Estimation, S. N. Balakrishnan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Decoupling of the dynamical equations in polar coordinates is used to develop a control scheme for use in target-intercept problems with passive measurements. By defining a pseudo control variable in the radial coordinate, the radial dynamics is made independent of the transverse dynamics. After solving for the radial control, the transverse control is determined through solutions to a two-point boundary value problem. Numerical results from a six degree-of-freedom simulation which used the decoupled control indicate that it is better than the completely Cartesian coordinate control for most of the cases considered. Decoupled control, though, is obtained iteratively through a two-point …