Engineering Commons^™

The Durability Of Hot Mix Asphalt With Petroleum Contaminated Soils, Bonnie H. Dubose

Theses

Petroleum contaminated soils are considered solid waste They must be taken to solid waste facilities such as landfills or some other method must be found to deal with them. Landfills are becoming limited and is looked upon by the government as the least attractive option. One method that looks promising is to use petroleum contaminated soils in Hot Mix Asphalt Concrete.

In the research program the following are examined: 1) Investigation of material properties of the petroleum contaminated soil and aggregates 2) The proper procedure to produce a design blend of asphalt concrete. 3) Establishing the test procedure protocol to …

Catalytic Ozone/Ultraviolet Light Oxidation Of Organics In Water : Integrated Charcoal/Ozonation/Uv Radiation, Dawei Wang

Theses

A novel heterogeneous catalytic-oxidation technology where activated carbon is used as a catalyst-adsorbent, ozone serves as the oxidant and UV light as activation agent, is developed in a lab scale study. We demonstrate this process for destruction of recalcitrant organics in water i.e: combined oxidation by ozone, UV light plus activated carbon. The investigation includes evalution of various operating conditions: ozone levels, activated carbon levels; time for complete destruction of the individual target pollutants, plus evalution of activity of the continuously recativated carbon surface in-situ. All experiments were performed at room temperature in a semi-batch reactor. Seven representative chemicals was …

Mathematical Model And Simulation Of The Progression Of Cutaneous T-Cell Lymphoma, Maria L. Agostinho

Theses

A simple mathematical model and simulation of the progression of cancer with particular emphasis on Cutaneous T Cell Lymphoma was investigated. The mathematical model consists of a set of differential equations that first satisfies the homeostasis levels of the different components present and second predicts the dynamics during a diseased or unhealthy condition. The simulation was done using a FORTRAN program for integrating the differential equations.

Simulation of the immune system is important in evaluating the usefulness of particular sorts of biologically targeted therapies and in selecting the most promising treatment strategies for clinical trials. In particular, the effects of …

An Information Theoretic Approach To Dsn Evaluation, Vivek Mehrotra

Theses

Evaluation of Distributed Sensor Networks (DSN's) for optimal detection using Bayesian cost formulation methods has been the objective of several studies. There have been a few studies on DSN evaluation using an information theoretic approach, wherein an assymetric channel models a detector. We look at the multi-sensor system at the receiver as a black-box and model it as an assymetric channel whose cross over probabilities depend on the probabilties of detection and of false alarm. These probabilities in turn depend on the thresholds of the local detectors and on the fusion rule used. We consider the case wherein the receiver …

1992 Scholars And Artists Bibliography, Michael Schwartz Library, Cleveland State University, Friends Of The Michael Schwartz Library

Scholars and Artists Bibliographies

This bibliography was created for the annual Friends of the Michael Schwartz Library Scholars and Artists Reception, recognizing scholarly and creative achievements of Cleveland State University faculty, staff and emeriti

Photoluminescence And Raman Studies Of Cds Films Grown By Metal-Organic Chemical Vapor Deposition On Si{111} Substrates, Alok K. Berry, P. M. Amirtharaj, Jing Tong Du, Jack L. Boone, Don D. Martin

Electrical and Computer Engineering Faculty Research & Creative Works

CdS epitaxial films grown using metal-organic chemical vapor deposition on Si{111} substrates at growth temperatures ranging from 270 to 325 °C have been characterized using photoluminescence and Raman spectroscopy. Out of all the samples the best optical behavior is obtained from that grown at the lowest temperature. Samples grown at the lowest temperature exhibited increased intensity of the bound excitonic peaks and reduced emission at the defect-related luminescence region. The Raman spectra were compatible with the film surface being normal to the c axis, indicating a preferred growth orientation. © 1992.

Hurricane Andrew Photovoltaic Traffic Control Relief, Florida Solar Energy Center, William Young

FSEC Energy Research Center®

On August 24, 1992 Hurricane Andrew damaged and destroyed much of South Florida. The storm destroyed buildings, structures, and traffic devices along the highway. Travel was hazardous with debris in the roadway, traffic signals damaged or not working, and signs missing. This disaster offered a unique opportunity to research and evaluate the potential for using photovoltaic power systems in emergency traffic control situations. This report describes the findings of this study completed by the Florida Solar Energy Center sponsored by the Florida Department of Transportation.

The Use Of Laboratory Testing To Understand The Behavior Of Collapsible Soil Upon Wetting, Martha H. Denham

Dissertations and Theses

In developing a constitutive model that could predict the settlement due to the collapse, several goals needed to be met. These were to gain an understanding of the collapse phenomenon, knowing the soil properties at the natural water content and how they change after collapse, and develop and test the new model. It was felt that laboratory testing could be of use. The types of test conducted included use of the Oedometer, Pressuremeter, and Triaxial tests. The material that was used for the testing was a "generic" soil manufactured out of diatomite. In all of the tests the soil was …

Spaceflight Payload Design, Flight Experience G-408, William W. Durgin, Fred J. Looft, Albert Sacco, Jr., Robert Thompson, Anthony G. Dixon, Dino Roberti, Robert Labonte, Larry Moschini

Office of the Provost Scholarship

Worcester Polytechnic Institute's first payload of spaceflight experiments flew aboard Columbia, STS-40, during June of 1991 and culminated eight years of work by students and faculty. The Get Away Special (GAS) payload was installed on the GAS bridge assembly at the aft end of the cargo bay behind the Spacelab Life Sciences (SLS-l) laboratory. The experiments were turned on by astronaut signal after reaching orbit and then functioned for 72 hours. Environmental and experimental measurements were recorded on three cassette tapes which, together with zeolite crystals grown on orbit, formed the basis of subsequent analyses.

The experiments were developed over …

Tests Of Profiled Steel Decks With V-Stiffeners, E. S. Bernard, Russell Q. Bridge, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The size and position of intermediate stiffeners in the compression flanges of thin-walled profiled steel decks exerts a strong influence on the dominant buckling mode of the flange. The ability of the deck to provide both high load carrying capacity before the onset of elastic buckling and a high ultimate load capacity may therefore be affected. A programme of tests to determine the effectiveness of intermediate stiffeners in controlling buckling modes has been undertaken. A series of specimens were loaded in pure bending resulting in various buckling waveforms prior to ultimate failure through a plastic collapse mechanism. All specimens were …

Flexural Capacity Of Discretely Braced C'S And Z'S, Thomas Sputo, Jack Haynes, Duane S. Ellifritt

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The American Iron and Steel Institute's Specification for the Design of Cold-Formed Steel Structural Members (1) presently requires that channel and zee flexural members, when not attached to sheathing, be braced against twist and lateral translation at the quarter-points of the span (Section D3.2.2). This provision first appeared in the Second Edition of the Specification in 1956, and has been there through all succeeding editions up through the 1989 Addendum. The newest formula for lateral buckling (part (a) of C3.1.2) is a more exact procedure for calculating lateral torsional buckling of a doubly, singly, or point symmetrical section than was …

Tests Of Continuous Purlins Under Downwards Loading, Michael Celeban, Chris Healy, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The paper describes a test program on purlin-sheeting systems for which the sheeting was screw fastened to the purlins. The test program simulates downwards loading. Z-section purlins were tested in three span continuous lapped configurations. The test purlins were supported by a range of bridging (bracing) members ranging from no bracing to one brace per span. The test results are compared with the design values computed using the Australian Cold-Formed Steel Structures Standard (AS1538-1988). The Australian Standard design is based on a flexural-torsional buckling analysis which may include the restraint from attached sheeting.

The Buckling Behaviour Of Hollow Flange Beams, Mahen Mahendran, T. J. Heidt

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A new cold formed structural section known as the hollow flange beam is currently under development in Australia. This section will have many applications, particularly in portal frame buildings. This paper discusses the lateral distortional buckling behaviour of the hollow flange beam.

Recent Research And Developments In Cold-Formed Steel Design And Construction, Wei-Wen Yu, Roger A. Laboube

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Unstiffened Elements - Some Interesting Features - Tests of Profiled Steel Decks with V-Stiffeners - Bending Strength of Beams with Non-Linear Analysis - Local and Distortional Buckling of Thin-Walled Beams - Design of C-Sections Against Deformational Lip Buckling - Lateral Buckling of Singly Symmetric Beams - Flexural Capacity of Discretely Braced C's and Z's - The Buckling Behaviour of Hollow Flange Beams - Experimental Investigations of I-Beams - Tests of Continuous Purlins Under Downwards Loading - Tests of Full-Scale Roofing Systems - Profiled Sheet Behaviour Under Concentrated Load - On Design of Profiled Sheets with Varying Cross Sections - Properties …

Stainless Steel Tubular Beams - Tests And Design, Gregory J. Hancock, Kim J. R. Rasmussen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The paper presents tests on square and circular stainless steel tubular beams. An important part of the test programme was to quantify the increase in bending strength resulting from cold-work during the fabrication process. Tension and compression tests on coupons cut from finished tubes were also included in the test programme. Stress-strain curves for shear were obtained using the coupon test results and the concept of affinity factors. A design method is proposed for stainless steel tubular beams. The method incorporates the increase in strength produced by the cold-rolling process and is validated by comparing it to the test strengths. …

Bending Strength Of Beams With Non-Linear Analysis, Pekka Salmi, Asko Talja

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Bending strengths of open cross-section beams cold-formed from high-strength steel (HSS) are determined with non-linear analysis. Two kinds of beams are studied. The short beams are for examining the bending resistance of cross-sections and the long beams for studing the lateral buckling of open sections. The beams are modelled with shell elements and non-linear FEM analyses are carried out to predict the strengths of the models. Both material and geometrical non-linearities are included in the analyses. The results are compared with experimental results.

Local And Distortional Buckling Of Thin-Walled Beams, Reynaud Serrette, Teoman Pekoz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Recent research has characterized the behavior of panel beams with laterally unsupported compression flanges as either a complex local buckling mode or an overall buckling mode. Tests have shown that the behavior of the unsupported flange and web is similar to that of lateral buckling, except, rotation is enforced along the axis of the web and the tension flange--a behavior which may be described as distortional buckling. In the work described here, an analytical expression is presented for computing the elastic distortional buckling stress based on a model which treats the web and compression flange as an elastically restrained beam. …

Lateral Buckling Of Singly Symmetric Beams, Teoman Pekoz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

General solutions for the elastic lateral buckling moment of singly symmetric sections are studied. The studies include the effect of the location of the load on the section as well as the effect of moment gradients on the lateral buckling moment. Design provisions are outlined for the case of moment gradients.

On Design Of Profiled Sheets With Varying Cross Sections, Laszlo Horvath, Miklos Nemeti, Bela Veroci

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A short review is given on the effective width concept and about its use for determining of the moment capacity of sheets. A modified method, taking into account the varying flexural rigidity along the spans, is described and illustrated on examples carried out on first -generation panels.

Influence Of Deformed Metal Decking Composite Floors To Beam-Column Connections, Y. Xiao, D. A. Nethercot, B. S. Choo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A series of tests designed to investigate the interaction of a variety of different steel beam to column connection details with a composite metal deck floor is described. The main emphasis is on assessing the connections' moment capacity, rotational stiffness and rotation capacity. The full details of the experimental behaviour of the flush end plate and partial depth end plate connections will be described in this paper. A simple method for moment capacity calculation based on the test results is proposed herein.

The Bi-Axial Behaviour Of Shear Connectors In Composite Slabs And Beams, Chris T. Duffy, David O'Leary, Michel Montourcy

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The use of composite beams which utilise steel beams together with a composite steel sheet/concrete floor slab is well developed. Many forms of steel profile are used and the form of attachment to the steel beam is generally by welded shear studs or shot-fired shear connectors. The design procedures for these beams require a knowledge of the shear capacity of the connectors which may be influenced by the type of profile being used for the beam. This shear capacity is often deduced from information obtained from standard push-off tests which mayor may not include in the test set-up the actual …

Activities Of The Center For Cold-Formed Steel Structures, Wei-Wen Yu, Roger A. Laboube

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The Center for Cold-Formed Steel Structures was established at the University of Missouri-Rolla in May 1990 under the sponsorship of the American Iron and Steel Institute and the University of Missouri-Rolla. This paper summarizes the activities performed at the Center during the past two years.

Education In Cold-Formed Steel Structures - Lifelong Learning, Albert L. Johnson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

What is the system we're dealing with? Who's in the audience? What is the information we need? How do we package it? How is it delivered? How do we know if we've done a good job?

Behavior Of Arc Spot Weld Connections In Tension, Roger A. Laboube, Wei-Wen Yu

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A comprehensive experimental study of the tension strength of arc spot weld connections, that affix a cold-formed steel roof deck to its support member, was conducted. Based on the experimental results obtained from over 260 connection tests, equations have been developed that predict the tension capacity of an arc spot weld connection. These equations are easily applied, and lend themselves to use by structural designers.

Experimental Investigations Of I-Beams, Shang-Jian Chen, Shan-Feng Fang

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

I - beams made of cold - formed thin - walled channels, back to back, can be connected by resistance spot welding or arc-welding. Both stability and ultimate strength of these beams are different for welding method. The stability can be increased provided several battens are attached on the open sections of these beams.

Contrasting Behaviour Of Thin Steel Roof Claddings Uder Simulated Cyclonic Wind Loading, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

During an investigation on thin steel roof claddings under simulated cyclonic wind loading, it was found that trapezoidal roofing behaved quite differently to corrugated roofing due to the presence of overload cycles. This paper examines this contrasting behaviour of these two roofing profiles.

Profiled Sheet Behaviour Under Concentrated Load, Mohsen M. Salaheldin, Lweis C. Schmidt

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The behaviour of profiled sheets under concentrated static load is discussed. The effect of aspect ratio and the depth of the sheet on the redistribution of stresses is investigated. The stress concentration caused by the concentrated load can lead to an anomalous pattern of behaviour, where local plastic failure occurs at lower loads in shorter spans rather than in longer spans.

Properties For Cellular Decks In Negative Bending, K. Balaji, Larry D. Luttrell

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cellular roof and floor decks may be formed by attaching essentially flat sheets to a "hat-shapes" or to fluted profiles by spot welding along the contact lines. This leads to a closed cellular deck unit suitable for such purposes as in-floor power distribution or communication systems. In positive bending, or when the flat sheet is in tension and stable, cellular deck flexural properties can be determined following the American Iron and Steel Institute Cold Formed Steel Design Manual. When the flat sheet is in compression, its contribution is not described in the AISI Manual since it is not continuously connected …

Composite Slabs Analyzed By Block Bending Test, Li An, Krister Cederwall

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A new small-scale test, concrete block bending test, was carried out to determine the amount of shear stress and the slip distribution at the interface between the steel sheet and the concrete. The result was then used in the finite element analysis to predict the behaviour of composite slabs. Good agreement has been shown between the analytical results and measured results from the full-scale composite slabs.

Repeated Point Loading Tests On Composite Slabs, Yoshimitsu Itoh, Kiyoshi Komori, Hiroshi Fujioka

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Single span and double span composite slab specimens were tested by subjecting them to concentrated repeated point loading. From the test results, it was found that the control of concrete cracks caused by the negative moment over the interior support is important in the latter case.