Engineering Commons^™

Test 1668: John Deere 7800 Powerquad Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Consumption And Loss Of Formaldehyde In Electroless Copper Plating, Peter John F. Sutch

Retrospective Theses and Dissertations

The objectives of this research were to quantify formaldehyde consumption due to plating and parasitic reactions and determine the magnitude and distribution of formaldehyde losses from the electroless copper plating process. Plating and rinse bath samples obtained from three electroless copper plating operations were analyzed for formaldehyde and copper in order to develop a mass balance analysis about the plating bath for periods of active production and no production. Fugitive air and stack releases of formaldehyde were estimated using emission factors developed from air sampling at the three facilities. It was determined that approximately 90% of the formaldehyde added to …

Computer Model For Predicting Aids Among Intravenous Drug Users, Daniel Berleant, R. Ron Goforth, Jun Yuan

Journal of the Arkansas Academy of Science

Intravenous drug abuse (IVDA) is an important cause of HIV transmission. Computer simulation is one way to understand and predict the spread of HIV infection among IVDAs. We design and simulate HIV infection among IVDAs and the impact of AIDS on this community, and thereby predict future IVDA population, HIV levels, AIDS levels, and AIDS deaths in this group. The HIV to AIDS, and AIDS to Death latencies are described by probability density functions (PDFs) in this model. Factors such as the recruit, quit, and normal death rate of IVDAs, are considered, as well as the infection and removal rates …

Semi-Insulating Polysilicon Hetero- And Isotype Junctions On Silicon, R. M. Ranade, S. S. Ang, W. D. Brown

Journal of the Arkansas Academy of Science

The effects of nitrogen trifluorideinthe gas stream during deposition of semi-insulating polysilicon (SIPOS) on the electrical characteristics of undoped (SIPSO)/p-Si, and n+-SIPOS/n-Si isotype junctions were investigated. The current-voltage characteristics of undoped SIPOS/p-Si heterojunctions exhibit a strong dependence on the oxygen content of the SIPOS film and depart from a hyperbolic sine behavior as the refractive index of the SIPOS increases.. The addition of nitrogen trifluoride decreases the current density of these undoped SIPOS/p-Si heterojunctions due presumably to the oxidation/hydrolysis of SiF species intoSiO2. The n+-SIPOS formed a rectifying isotype junction o n-Si. The forward current voltage characteristics exhibit two distinct …

Detection Of Skin Tumor Boundaries In Color Images, Fikret Erçal, M. Moganti, William V. Stoecker, Randy Hays Moss

Computer Science Faculty Research & Creative Works

A simple and yet effective method for finding the borders of tumors is presented as an initial step towards the diagnosis of skin tumors from their color images. The method makes use of an adaptive color metric from the red, green, and blue planes that contains information for discriminating the tumor from the background. Using this suitable coordinate transformation, the image is segmented. The tumor portion is then extracted from the segmented image and borders are drawn. Experimental results that verify the effectiveness of this approach are given

Economic Impacts Of Noxious Facilities: Incorporating The Effects Of Risk Aversion, Leslie A. Nieves

RISK: Health, Safety & Environment (1990-2002)

The author suggests an integrative approach for projecting economic impacts of facilities that elicit public Risk aversion. She incorporates both economic stimulus effects and perception-based effects of facilities on the host area economy. Empirical findings are compared and an impact estimation framework is suggested for integrating psychometric and econometric techniques.

Temporal Development Of Electric Field Structures In Photoconductive Gaas Switches, K. H. Schoenbach, J. S. Kenney, F.E. Peterkin, R. J. Allen

Bioelectrics Publications

The temporal development of the electric field distribution in semi‐insulating GaAs photoconductive switches operated in the linear and lock‐on mode has been studied. The field structure was obtained by recording a change in the absorption pattern of the switch due to the Franz–Keldysh effect at a wavelength near the band edge of GaAs. In the linear mode, a high field layer develops at the cathode contact after laser activation. With increasing applied voltage, domainlike structures become visible in the anode region and the switch transits into the lock‐on state, a permanent filamentary electrical discharge. Calibration measurements show the field intensity …

1993 Directory Of Indiana State, County, City And Town Officials Responsible For Road And Street Work, Herpicc

Indiana Local Technical Assistance Program (LTAP) Directory

Contact information for agency officials and employees responsible for Indiana’s local road infrastructure.

Interposed Abdominal Compression Cardiopulmonary Resuscitation: Are We Missing The Mark In Clinical Trials?, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Publications

Straightforward considerations of abdominal anatomy in human beings set tight constraints on the theoretically optimal technique for abdominal compressions during interposed abdominal compression (IAC)-CPR. The location and extent of the abdominal aorta lead naturally to the recommendation that IAC be applied at a level corresponding to the lower two thirds of the sterno-umbilical line. The force vector required to achieve contact compression of the abdominal aorta is inclined in the transverse plane at an angle of 11 degrees from the vertical toward the left. Such slightly angled compression subjects the abdominal aorta to maximally flattening; while the inferior vena cava …

Interposed Abdominal Compression-Cpr: A Case Study In Cardiac Arrest Research, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Publications

When the abdomen is compressed manually in counterpoint to the rhythm of chest compression, in the performance of interposed abdominal compression-CPR, artificial circulation is approximately doubled in animal experiments and in electronic models of the circulatory system. These studies suggest that external manual compression of the abdominal aorta acts like an intra-aortic balloon pump to increase aortic pressure, whereas external manual compression of the abdominal veins acts to prime the right heart and pulmonary vessels before the next chest compression. As a result, perfusion pressures and flows are increased. Several clinical studies of this technique have shown promising results, including …

Development Of A Rapidly Computable Descriptor Of Prostate Tissue Temperature During Transurethral Conductive Heat Therapy For Benign Prostate Hyperplasia, U H. Patel, Charles F. Babbs

Weldon School of Biomedical Engineering Faculty Publications

Benign prostate hyperplasia (BPH) is a condition in older men in which the mass of tissue in the prostate gland gradually increases over the course of many years, ultimately leading to urinary outflow obstruction. Current treatment of this condition is to surgically remove the obstructing tissue. One novel alternative therapy being studied is transurethral thermocoagulation of excessive prostatic mass. In this approach, a heat emitting catheter is placed in the prostatic urethra, and the intraprostatic segment of the catheter is heated to temperatures above 60 oC for one hour. Two dimensional cylindrical coordinate computer simulations of this treatment modality were …

A Spectral Flux Method For Solving The Boltzmann Equation, Muhammad A. Alam, Mark A. Stettler, Mark S. Lundstrom

Department of Electrical and Computer Engineering Faculty Publications

A spectral method for solving the Boltzmann equation by the scattering matrix approach is presented, The algorithm discussed can be used to simulate both bulk and device properties with arbitrary field profiles. Although the primary goal is to reduce the data storage problem of the scattering matrix approach, many of the concepts and mathematical properties developed may be useful for other traditional spectral methods as well.

Minority-Carrier Mobility Enhancement In P+ Ingaas Lattice Matched To Inp, E. S. Harmon, Michael L. Lovejoy, Michael R. Melloch, Mark S. Lundstrom, D. Ritter, R. A. Hamm

Department of Electrical and Computer Engineering Faculty Publications

Minority electron mobilities in pf-In0.ssGac4, As have been measured with the zero field time-of-flight technique. The room-temperature (297 K) minority electron mobilities for p+-In,, 53Gac47A~ doped 0.9 and 3.1 x 10” cmm3 are found to be 2900 and 3300 cm* V-’ s-l, respectively. These are the first measurements to demonstrate enhancement in minority-carrier mobility as doping is increased for heavily doped Ines3Gae.4+s. This enhancement in mobility as doping is increased is similar to that observed in p+-GaAs, which has been attributed to reductions in plasmon and carrier-carrier scattering between minority electrons and majority holes.

Concentration‐Dependent Optical‐Absorption Coefficient In N‐Type Gaas, Gregory Benedict Lush, H. F. Macmillan, S. Asher, Michael R. Melloch, Mark S. Lundstrom

Department of Electrical and Computer Engineering Faculty Publications

The doping-dependent, near-band-edge optical-absorption coefficient CY(h v) was deduced from optical transmission measurements in n-type GaAs thin films. The selenium-doped films were grown by metalorganic chemical-vapor deposition and do ed to produce room-temperature electron concentrations from 1.3 x 10” to 3.8X 1018 cm- P . The transmission measurements covered photon energies between 1.35 and 1.7 eV and were performed on double heterostructures with the substrate removed by selective etching. The results show good qualitative agreement with previous studies and good quantitative agreement, except for the heavily doped samples. For na=3.8 X 10” cme3, a( 1.42 eV> is approximately four times …

Experimental Observation Of A Minority Electron Mobility Enhancement In Degenerately Doped P-Type Gaas, E. S. Harmon, Michael L. Lovejoy, Michael R. Melloch, Mark S. Lundstrom, T. J. De Lyon, J. M. Woodall

Department of Electrical and Computer Engineering Faculty Publications

The variation of minority electron mobility with doping density in p+-GaAs has been measured with the zero-field time-of-flight technique. The results from a series of nine GaAs films doped between 1 X lOI and 8 X 10” cmm3 show the mobility decreasing from 1950 cm2 V-’ s-l at 1 X 10” cmm3 to 1370 cm2 V-l s-l at 9X 10” cmB3. For the doping range 9 x 1018-8x 1019 cme3, the decreasing trend in mobility is reversed. The measured mobility of 3710 cm2 V-’ s-l at 8 X 10” cmp3 is about three times higher than the measured value at …

Feature Extraction And Classification Algorithms For High Dimensional Data, Chulhee Lee, David Landgrebe

Department of Electrical and Computer Engineering Technical Reports

In this research, feature extraction and classification algorithms for high dimensional data are investigated. Developments with regard to sensors for Earth observation are moving in the direction of providing much higher dimensional multispectral imagery than is now possible. In analyzing such high dimensional data, processing time becomes an important factor. With large increases in dimensionality and the number of classes, processing time will increase significantly. To address this problem, a multistage classification scheme is proposed which reduces the processing time substantially by eliminating unlikely classes from further consideration at each stage. Several truncation criteria are developed and the relationship between …

Test 1663: Case International 7150 And 7250 Diesels 18-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1665: John Deere 7600 Powershift Diesel 19-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1666: John Deere 7700 Powerquad Diesel 16-Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1672: John Deere 8870 Powersync Diesel 12 And 24 Speeds, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Test 1673: John Deere 8970 Powersync Diesel 12 And 24 Speed, Nebraska Tractor Test Lab

Nebraska Tractor Tests

EXPLANATION OF THE TEST PROCEDURE General Tractors are tested at the University of Nebraska according to the Agricultural Tractor Test Code approved by the American Society of Agricultural Engineers and the Society of Automotive Engineers or official Nebraska test procedure. The manufacturer selects the tractor to be tested and certifies that it is a stock model. Each tractor is equipped with the common power consuming accessories such as power steering, power lift pump, generator, etc., if available. Power consuming accessories may be disconnected only when the means for disconnecting can be reached from the operating station. An official representative of …

Nebraska Summary: S143 Case-Ih 5230, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S299 Agco Allis 5660, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Assessment Of Environmental Implications Of Abandoned Oil And Gas Wells, Donald L. Warner, Cary L. Mcconnell

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

A detailed study was made of the potential for abandoned oil and gas wells in the Lower Tuscaloosa sand of Mississippi and Louisiana to act as conduits for movement of saline water from the Lower Tuscaloosa into underground sources of drinking water (USDW's). Finite-difference numerical modeling determined the extent that water might be forced from the Lower Tuscaloosa sand into a USDW as a result of injection into the Lower Tuscaloosa. Within the range of conditions modeled, water from the Lower Tuscaloosa never traveled into a USDW. On the basis of the modeling, we concluded that it is unlikely that …

Reversible Complexation Of O2 To (Meso-Tetraphenylporphyrinato)Cobalt(Ii) Plasma Polymer And Sublimed Films At Room Temperature, J. M. Skelly, Nicholas C. Morosoff, V. T. Stannett, A. L. Crumbliss

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Cultural Transposition: Exploring Meanings Of And Strategies For Cross-Cultural Transfer Of Organizational Practices, Yongming Tang

Engineering Management & Systems Engineering Theses & Dissertations

The research objective is to study the phenomenon of transferring organizational practices which are conceptualized in one culture to another different culture. The purpose of the study is (1) to understand how cultural values and beliefs are manifested in behavior; (2) to explore how the Western organizational practices are interpreted and assimilated into an organization in an Eastern culture; and (3) to explore strategies for the fit between local cultural orientations and imported organizational practices. A qualitative, interpretive, and reflexive research methodology was developed to conduct this study.

The study was conducted in two phases. The first phase was designed …

On Minimizing Thermal Deflections Of Laminated Plates, Serge Abrate

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Thermal deflections of symmetrically laminated plates that are continuous over many line supports are determined using the Rayleigh-Ritz method. The constitutive equations and the thermal loads are expressed in terms of four non-dimensional lamination parameters. Layups that minimize thermal deflections are determined for several types of composite plates subjected to temperature increases that vary linearly through the thickness.

Computer Simulation Of Three-Dimensional Mechanical Assemblies: Part Ii - Computer Simulation, T. C. Chou, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Computer simulation of the kinematic and dynamic behaviors of mechanical assemblies has become a very important tool in design and manufacturing, because the designer can foresee how a product is going to perform before the product is actually fabricated. However, up to now, the most current simulation modules are based on analysis from another kinematic or dynamic module by specifying the mating conditions between components, and then displaying the motion on the screen. This computer simulation actually performs similarly to a movie and can only provide visual checking. The drawback of this simulation approach is that designers are forced to …

Computer Simulation Of Three-Dimensional Mechanical Assemblies: Part I - General Formulation, Yong Fang, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In Part I of this paper, a dynamic modeling system for the simulation of three-dimensional mechanical assemblies is presented. With this simulation tool, a designer can interactively create an assembly of mechanical components ready for dynamic analysis. The modeling system presented in this paper include» the derivation of the equations of motion of spatial multi-body systems, and the formulation of the equations to model the associated collision detection and collision responses. Part II of this paper is to introduce the geometry modeling and computer simulation of 3D systems.

Second Law Analysis Of Active Magnetic Regenerative Hydrogen Liquefiers, L. Zhang, S. A. Sherif, T. N. Veziroglu, John W. Sheffield

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Recent published work in the area of magnetic refrigeration reports on its potential for greater efficiency and high reliability. This paper presents an exergy analysis of a three-stage active magnetic regenerative (AMR) hydrogen liquefier which cools a hydrogen gas stream at 77 K and 1 atm to hydrogen liquid at 20 K. Ortho - para conversion of hydrogen is accomplished in a heat exchanger employing a 10 atm helium fluid that cycles in the refrigerator. The performance of the system is described in terms of the cooling capacity and exergy losses as functions of the magnetic material type, magnetic bed …